This study aims to investigate the responses of a perovskite-based direct-conversion dual-layer flat-panel detector(DL-FPD)numerically.To this end,the X-ray sensitivity,spatial resolution quantified by the modulation ...This study aims to investigate the responses of a perovskite-based direct-conversion dual-layer flat-panel detector(DL-FPD)numerically.To this end,the X-ray sensitivity,spatial resolution quantified by the modulation transfer function(MTF),and detective quantum efficiency(DQE)of the DL-FPD are evaluated numerically using a linear cascade model.In addition,both the single-crystal(SC)and polycrystalline(PC)structures of MAPbI_(3)are investigated,along with various other key parameters such as the material thickness,electric field strength,X-ray beam spectrum,and electronic readout noise.The results demonstrate that SC perovskite consistently exhibits better performance than PC perovskite owing to fewer material defects.Increasing the layer thickness may decrease the MTF,but can also enhance the sensitivity and DQE.Moreover,appropriately increasing the external electric field within the material can improve the sensitivity,MTF,and DQE.Finally,reducing the electronic readout noise can significantly enhance the DQE for low-dose imaging.This study demonstrates the potential of high-quality dual-energy X-ray imaging using direct-conversion perovskite DL-FPDs.展开更多
Traditional digitizers for signal readout of PET detectors are based on commercial analog-to-digital converters(ADC).However,the cost and power consumption of an entire electronic readout system based on digitizers fo...Traditional digitizers for signal readout of PET detectors are based on commercial analog-to-digital converters(ADC).However,the cost and power consumption of an entire electronic readout system based on digitizers for a PET scanner are high.To address this problem,a soft-core ADC based on a field-programmable gate array(FPGA)was proposed.An FPGA-based ADC(FPGA-ADC)combines low loss and high performance.To achieve good performance,the FPGA-ADC requires three calibrations:time-to-digital converter(TDC)length calibration,TDC alignment calibration,and TDC-to-ADC calibration.A prototype front-end electronics based on FPGA-ADC was built to evaluate the performance of time-of-flight positron emission tomography(TOF PET)detectors.Each PET detector consists of a LYSO crystal single-ended coupled to a silicon photomultiplier(SiPM).The experimental results show that the full-width at half-maximum(FWHM)energy resolution for 511 keV gamma photons after saturation correction of the SiPM was 12.3%.The FWHM coincidence timing resolution(CTR)of the TOF PET detector with the readout of the front-end electronic prototype is 385.2 ps.FPGA-ADCbased front-end electronics are very promising for multichannel,low-cost,highly integrated,and power-efficient readout electronic systems for radiation detector applications.展开更多
Detector and event visualization are crucial components of high-energy physics(HEP)experimental software.Virtual reality(VR)technologies and multimedia development platforms,such as Unity,offer enhanced display effect...Detector and event visualization are crucial components of high-energy physics(HEP)experimental software.Virtual reality(VR)technologies and multimedia development platforms,such as Unity,offer enhanced display effects and flexible extensibility for visualization in HEP experiments.In this study,we present a VR-based method for detector and event displays in the Jiangmen Underground Neutrino Observatory(JUNO)experiment.This method shares the same detector geometry descriptions and event data model as those in the offline software and provides the necessary data conversion interfaces.The VR methodology facilitates an immersive exploration of the virtual environment in JUNO,enabling users to investigate the detector geometry,visualize event data,and tune the detector simulation and event reconstruction algorithms.Additionally,this approach supports applications in data monitoring,physics data analysis,and public outreach initiatives.展开更多
We present the preparation and measurement of the radioactive isotope^(37)Ar,which was produced using thermal neutrons from a reactor,as a calibration source for liquid xenon time projection chambers.^(37)Ar is a low-...We present the preparation and measurement of the radioactive isotope^(37)Ar,which was produced using thermal neutrons from a reactor,as a calibration source for liquid xenon time projection chambers.^(37)Ar is a low-energy calibration source with a half-life of 35.01 days,making it suitable for calibration in the low-energy region of liquid xenon dark-matter experiments.Radioactive isotope^(37)Ar was produced by irradiating ^(36)Ar with thermal neutrons.It was subsequently measured in a gaseous xenon time projection chamber(GXe TPC)to validate its radioactivity.Our results demonstrate that^(37)Ar is an effective and viable calibration source that offers precise calibration capabilities in the low-energy domain of xenon-based detectors.展开更多
We here report a high system detection efficiency(SDE)superconducting single-photon detector(SSPD)at 2μm wavelength.The device integrates a SiO_(2)/Ta_(2)O_(5)distributed Bragg reflector(DBR)and a sandwich-structured...We here report a high system detection efficiency(SDE)superconducting single-photon detector(SSPD)at 2μm wavelength.The device integrates a SiO_(2)/Ta_(2)O_(5)distributed Bragg reflector(DBR)and a sandwich-structured double-layer NbN nanowire to enhance the optical absorption efficiency.A cold development technique is implemented to optimize the superconducting nanowires with sub-40-nm linewidths,thus enhancing the intrinsic detection efficiency(IDE).The fabricated SSPD shows an SDE exceeding 90% at 2μm wavelength.Moreover,the detector allows an operational working temperature of 2.2 K provided by a compact GM cryo-cooler.This detector delivers excellent performance at the 2μm wavelength,and its optimized structural design implies promising potential for extending detection toward longer infrared bands.It thus holds value for advancing high-sensitivity quantum technologies,mid-infrared optical communications,and dark matter detection research.展开更多
The accessibility of urban public transit directly influences residents’quality of life,travel behavior,and social equity.Its correlation with housing prices has garnered significant attention across disciplines such...The accessibility of urban public transit directly influences residents’quality of life,travel behavior,and social equity.Its correlation with housing prices has garnered significant attention across disciplines such as geography,economics,and urban planning.Although much existing research focuses on the impact of individual transportation facilities on housing prices,there is a notable gap in comprehensive analyses that assess the influence of overall urban transit accessibility on housing market dynamics.This study selected the main urban area of Hefei,China,as a case to investigate the spatial distribution of housing prices and evaluate public transit accessibility in 2022.Employing techniques such as the optimized parameter geographical detector and local spatial regression models,the study aimed to elucidate the effects and underlying mechanisms of urban transit accessibility on housing prices.The findings revealed that:1)housing prices in Hefei exhibited a clustered spatial pattern,with high prices concentrated in the city center and lower prices in peripheral areas,forming three distinct high-price hotspots with a‘belt-like’distribution;2)public transit accessibility showed a‘coreperiphery’structure,with accessibility declining in a‘circumferential’pattern around the city center.Based on the‘housing price-accessibility’dimension,four categories were identified:high price-high accessibility(37.25%),high price-low accessibility(19.07%),low price-high accessibility(21.95%),and low price-low accessibility(21.73%);3)the impact of transit accessibility on housing prices was spatially heterogeneous,with bus travel showing the strongest explanatory power(0.692),followed by automobile,subway,and bicycle travel.The interaction of these transportation modes generated a synergistic effect on housing price differentiation,with most influencing factors contributing more than 25%.These findings offer valuable insights for optimizing the spatial distribution of public transit infrastructure and improving both urban housing quality and residents’living standards.展开更多
Formamidinium lead iodide(FAPbI_(3))perovskite exhibits an impressive X-ray absorption coefficient and a large carrier mobility-lifetime product(μτ),making it as a highly promising candidate for X-ray detection appl...Formamidinium lead iodide(FAPbI_(3))perovskite exhibits an impressive X-ray absorption coefficient and a large carrier mobility-lifetime product(μτ),making it as a highly promising candidate for X-ray detection application.However,the presence of larger FA^(+)cation induces to an expansion of the Pb-I octahedral framework,which unfortunately affects both the stability and charge carrier mobility of the corresponding devices.To address this challenge,we develop a novel low-dimensional(HtrzT)PbI_(3) perovskite featuring a conjugated organic cation(1H-1,2,4-Triazole-3-thiol,HtrzT^(+))which matches well with theα-FAPbI_(3) lattices in two-dimensional plane.Benefiting from the matched lattice between(HtrzT)PbI_(3) andα-FAPbI_(3),the anchored lattice enhances the Pb-I bond strength and effectively mitigates the inherent tensile strain of theα-FAPbI_(3) crystal lattice.The X-ray detector based on(HtrzT)PbI_(3)(1.0)/FAPbI_(3) device achieves a remarkable sensitivity up to 1.83×10^(5)μC Gy_(air)^(−1) cm^(−2),along with a low detection limit of 27.6 nGy_(air) s^(−1),attributed to the release of residual stress,and the enhancement in carrier mobility-lifetime product.Furthermore,the detector exhibits outstanding stability under X-ray irradiation with tolerating doses equivalent to nearly 1.17×10^(6) chest imaging doses.展开更多
Soft X-ray detectors play a vital role in materials science,high-energy physics and medical imaging.Cs_(2)AgBiBr_(6),a lead-free double perovskite,has gained attention for its excellent optoelectronic properties,stabi...Soft X-ray detectors play a vital role in materials science,high-energy physics and medical imaging.Cs_(2)AgBiBr_(6),a lead-free double perovskite,has gained attention for its excellent optoelectronic properties,stability,and nontoxicity.However,its fast crystallization and requirement for high-temperature annealing(>250℃)often lead to inferior film quality,limiting its application in flexible devices.This study introduces an alloying strategy that significantly improves the quality of Cs_(2)AgBiBr_(6)thin films annealed at a reduced temperature of 150℃.Devices based on the alloyed thin films exhibit an ultra-low dark current of 0.32 nA·cm^(-2)and a quantum efficiency of 725%.Furthermore,the first successful integration of Cs_(2)AgBiBr_(6)with a thinfilm transistor backplane demonstrates its superior imaging performance,indicating that Cs_(2)AgBiBr_(6)is a promising material for next-generation soft X-ray sensors.展开更多
Numerous sectors,such as education,the IT sector,and corporate organizations,transitioned to virtual meetings after the COVID-19 crisis.Organizations now seek to assess participants’fatigue levels in online meetings ...Numerous sectors,such as education,the IT sector,and corporate organizations,transitioned to virtual meetings after the COVID-19 crisis.Organizations now seek to assess participants’fatigue levels in online meetings to remain competitive.Instructors cannot effectively monitor every individual in a virtual environment,which raises significant concerns about participant fatigue.Our proposed system monitors fatigue,identifying attentive and drowsy individuals throughout the online session.We leverage Dlib’s pre-trained facial landmark detector and focus on the eye landmarks only,offering a more detailed analysis for predicting eye opening and closing of the eyes,rather than focusing on the entire face.We introduce an Eye Polygon Area(EPA)formula,which computes eye activity from Dlib eye landmarks by measuring the polygonal area of the eye opening.Unlike the Eye Aspect Ratio(EAR),which relies on a single distance ratio,EPA adapts to different eye shapes(round,narrow,or wide),providing a more reliable measure for fatigue detection.The VMFD system issues a warning if a participant remains in a fatigued condition for 36 consecutive frames.The proposed technology is tested under multiple scenarios,including low-to high-lighting conditions(50-1400 lux)and both with and without glasses.This study builds an OpenCV application in Python,evaluated using the iBUG 300-W dataset,achieving 97.5%accuracy in detecting active participants.We compare VMFD with conventional methods relying on the EAR and show that the EPA technique performs significantly better.展开更多
A phase-sensitive optical time domain reflectometer （φ-OTDR） based on a 120°-phase-difference Michelson in- terferometer is proposed. The Michelson interferometer with arm difference of 4m is used to test the ...A phase-sensitive optical time domain reflectometer （φ-OTDR） based on a 120°-phase-difference Michelson in- terferometer is proposed. The Michelson interferometer with arm difference of 4m is used to test the phase difference between the Rayleigh scattering from two sections of the fiber. A new demodulation method called the inverse transmission matrix demodulation scheme is utilized to demodulate the distributed phase from the backward scattering along the long fiber, The experimental results show that the 120°-phase-difference inter- ferometer φ-OTDR can detect the phase along the 3km fiber, and the acoustic signal within the whole human hearing range of 20 Hz-20 kHz is reproduced accurately and quickly.展开更多
Robust and fast fat suppression is a challenge in balanced steady-state free precession （SSFP） magnetic resonance imaging. Although single-acquisition phase-sensitive SSFP can provide fat-suppressed images in short ...Robust and fast fat suppression is a challenge in balanced steady-state free precession （SSFP） magnetic resonance imaging. Although single-acquisition phase-sensitive SSFP can provide fat-suppressed images in short scan time, phase errors, especially spatially-dependent phase shift, caused by a variety of factors may result in misplacement of fat and water voxels. In this paper, a novel phase correction algorithm was used to calibrate those phase errors during image reconstruction. This algorithm corrects phase by region growing, employing both the magnitude and the phase information of image pixels. Phantom and in vivo imagings were performed to validate the technique. As a result, excellent fat-suppressed images were acquired by using single-acquisition phase-sensitive SSFP with phase correction.展开更多
Objective:Late gadolinium enhancement(LGE) patterns of cardiovascular magnetic resonance (CMR) relying on PSIR(phase-sensitive inversion recovery sequence) techniques had been used to determine the characteristics of ...Objective:Late gadolinium enhancement(LGE) patterns of cardiovascular magnetic resonance (CMR) relying on PSIR(phase-sensitive inversion recovery sequence) techniques had been used to determine the characteristics of LGE in apical hypertrophic cardiomyopathy(ApHCM). Methods:Forty patients pure ApHCM[age,(60.2±10.4) years,31 men]were enrolled.LGE images were acquired using PSIR,and analyzed using a 17-segment model.Summing the LGE areas in all short axis slices yielded the total volume of late enhancement,which was subsequently presented as a proportion of total LV myocardium(%LGE).Results:Mean maximal apical wall thickness was(17.9±2.3) mm,and mean left ventricular(LV) ejection fraction was(67.7±8.0)%.LGE was detected in 130 segments of 30 patients(75.0%),occupying(4.9±5.5)% of LV myocardium.LGE was mainly detected at the junction between left and right ventricles in 12(30%) and at the apex in 28(70%),although LGE-positive areas were widely distributed,and not limited to the apex.Focal LGE at the non-hypertrophic LV segments was found in some ApHCM patients,even without LGE of hypertrophied apical segments.Conclusions:LGE was frequently observed not only in the thickened apex of the heart but also in other LV segments,irrespective of the presence or absence of hypertrophy.The simple presence of LGE on CMR was not representative of adverse prognosis in this population.展开更多
Objective:To determine the deference between phase sensitive magnetic resonance(MR) imaging and magnitude reconstruction to detect infracted myocardium.Methods:Twenty patients(16 men;4 women;mean age,56 years),experie...Objective:To determine the deference between phase sensitive magnetic resonance(MR) imaging and magnitude reconstruction to detect infracted myocardium.Methods:Twenty patients(16 men;4 women;mean age,56 years),experienced Q-wave myocardial infarction 2 weeks earlier were examined with a 3.0-T MR system 10 minutes after administration of 0.1 mmol/kg body weight gadobenate dimeglumine.To determine the optimal TI,a TI scout sequence was used.A segmented 2D IR true fast imaging with steady-state precession(trueFISP) sequence that produces both phase-sensitive and magnitude-reconstructed images were used at TI values of 200-600 msec(TI values were varied in 100-msec steps) and at optimal TI(mean value,330 msec).Contrast- noise ratios(CNRs) of normal and infarcted myocardium and the area of infarcted myocardium were determined.Two-tailed unpaired sample Student t test was used to compare CNRs,and area of infarction.Results:MMean CNR phase-sensitive and magnitude-reconstructed images at optimal TI(mean value,330 msec) were 6.2,and 6.1,respectively.For a TI of 200 msec,CNR values were 5.5,and 4.2,respectively;for TI of 600 msec,CNR values were 5.8 and 4.3,respectively.Area of infarcted myocardium was underestimated on magnitude-reconstruction images(P = 0.002-0.03) for short TI values(ie.,200 msec) but not on phase sensitive reconstructed when compared with IR tureFISP images obtained at optimal TI.Conclusions: LPhase-sensitive image reconstruction results in reduced need for precise choice of TI and more consistent image quality.展开更多
We study the colour-locked twin-noisy-field correlation effects in the fifth-order nonlinear susceptibility of ultrafast polarization beats in a cascade four-level system. More importantly, the fifth-order phase-sensi...We study the colour-locked twin-noisy-field correlation effects in the fifth-order nonlinear susceptibility of ultrafast polarization beats in a cascade four-level system. More importantly, the fifth-order phase-sensitive heterodyne detection of ultrafast polarization beats has been exploited. The fifth-order nonlinear optical response can be controlled and modified through the colour-locked correlation of twin noisy fields. Thus, this method with the phase dispersion information is a good way to measure the real and imaginary parts of the fifth-order nonlinear susceptibility.展开更多
We present a theoretical scheme for broadband multi-channel quantum noise suppression and phase-sensitive modulation of continuous variables in a coupled resonant system with quantum entanglement properties.The effect...We present a theoretical scheme for broadband multi-channel quantum noise suppression and phase-sensitive modulation of continuous variables in a coupled resonant system with quantum entanglement properties.The effects of different coupling strengths,pumping power in suppressing quantum noise and controlling the width of quantum interference channels are analyzed carefully.Furthermore,quantum noise suppression at quadrature amplitude is obtained with phase-sensitive modulation.It shows that the entanglement strength of the output field and the quantum noise suppression effect can be enhanced significantly by a strong pumping filed due to interaction of pumping light with the nonlinear crystal.The full width at half maxima(FWHM)of the noise curve at the resonant peak(△=0 MHz)is broadened up to 2.17 times compared to the single cavity.In the strong coupling resonant system,the FWHM at △=0 MHz(△=±3.1 MHz)is also broadened up to 1.27(3.53)times compared to the weak coupling resonant system case.The multi-channel quantum interference creates an electromagnetically induced transparent-like line shape,which can be used to improve the transmission efficiency and stability of wave packets in quantum information processing and quantum memory.展开更多
X-ray detectors show potential applications in medical imaging,materials science,and nuclear energy.To achieve high detection efficiency and spatial resolution,many conventional semiconductor materials,such as amorpho...X-ray detectors show potential applications in medical imaging,materials science,and nuclear energy.To achieve high detection efficiency and spatial resolution,many conventional semiconductor materials,such as amorphous selenium,cadmium telluride zinc,and perovskites,have been utilized in direct conversion X-ray detectors.However,these semiconductor materials are susceptible to temperature-induced performance degradation,crystallization,delamination,uneven lattice growth,radiation damage,and high dark current.This study explores a new approach by coupling an FC40 electronic fluorinated liquid with a specialized high-resolution and high-readout-speed complementary metal-oxide-semiconductor(CMOS)pixel array,specifically the Topmetal II−chip,to fabricate a direct conversion X-ray detector.The fluorinated liquid FC40(molecular formula:C_(21)F_(48)N_(2))is an electronic medium that is minimally affected by temperature and displays no issues with uniform conductivity.It exhibits a low dark current and minimal radiation damage and enables customizable thickness in X-ray absorption.This addresses the limitations inherent in conventional semiconductor-based detectors.In this study,simple X-ray detector imaging tests were conducted,demonstrating the excellent coupling capability between FC40 electronic fluorinated liquid and CMOS chips by the X-ray detector.A spatial resolution of 4.0 lp/mm was measured using a striped line par card,and a relatively clear image of a cockroach was displayed in the digital radiography imaging results.Preliminary test results indicated the feasibility of fabricating an X-ray detector by combining FC40 electronic fluorinated liquid and CMOS chips.Owing to the absence of issues related to chip-material coupling,a high spatial resolution could be achieved by reducing the chip pixel size.This method presents a new avenue for studies on novel liquid-based direct conversion X-ray detectors.展开更多
The PICOSEC Micromegas(MM)is a precise timing gaseous detector based on a Cherenkov radiator coupled with a semi-transparent photocathode and an MM amplifying structure.It features a two-stage amplification process th...The PICOSEC Micromegas(MM)is a precise timing gaseous detector based on a Cherenkov radiator coupled with a semi-transparent photocathode and an MM amplifying structure.It features a two-stage amplification process that leads to a significant deterioration of non-uniformity when scaling up to larger areas.Since the performance of gaseous detectors is highly dependent on the choice of working gas,optimizing the gas mixture offers a promising solution to improve the uniformity performance.This paper addresses these challenges through a combined approach of simulation based on Garfield++and experimental studies.The simulation investigates the properties of different mixing fractions of gas mixtures and their impact on detector performance,including gain uniformity and time resolution.To verify the simulation results,experimental tests were conducted using a multi-channel PICOSEC MM prototype with different gas mixtures.The experimental results are consistent with the findings of the simulation,indicating that a higher concentration of neon significantly improves the detector’s gain uniformity.Furthermore,the influence of gas mixtures on time resolution was explored as a critical performance indicator.The study presented in this paper offers valuable insights for improving uniformity in large-area PICOSEC MM detectors and optimizing overall performance.展开更多
Despite rapid advancements in lidar technology,extremely long-range observation remains a signifi⁃cant challenge.Recently,2μm lasers have demonstrated a potential to be applied in CDWL(Coherent Doppler Wind Lidar)sys...Despite rapid advancements in lidar technology,extremely long-range observation remains a signifi⁃cant challenge.Recently,2μm lasers have demonstrated a potential to be applied in CDWL(Coherent Doppler Wind Lidar)system,for its high atmospheric penetration capability through the atmosphere and high potential la⁃ser power.In this study,we present a 2μm balanced detector that consists of a pair of commercial positive-intrin⁃sic-negative(PIN)diodes with a low-noise transimpedance circuit.To meet the high bandwidth requirements,the highspeed transimpedance circuit and bias voltage tuning method were utilized to overcome the large capaci⁃tance of PIN diodes.The circuit transfer function,stability analysis and noise calculation have been studied.The detector was co-packaged with a data acquisition module for convenient data transmission and bias voltage con⁃trol.The characteristics of the detector,including bandwidth,noise and bias voltage influence,are evaluated in laboratory.Results show that the RMS value of the balanced detector background noise is 539μV and the band⁃widths of the two diodes are 110.8 MHz and 110.3 MHz,respectively.The evaluation results show that the bal⁃anced detector meets the wind measurement requirements and allows for a 1.45×increase in bandwidth through bi⁃as voltage tuning.Our work offers insights into lidar detector design and bandwidth enhancement,providing a valuable reference for researchers and professionals in the field.More importantly,it lays a critical foundation for fu⁃ture ultra-long-range and space-borne 2μm coherent wind lidar systems by addressing key device-level challenges.展开更多
To detect space gravitational waves in the extremely low-frequency band,the telescope and optic-al platform require high stability and reliability.However,the cantilevered design presents challenges,espe-cially in the...To detect space gravitational waves in the extremely low-frequency band,the telescope and optic-al platform require high stability and reliability.However,the cantilevered design presents challenges,espe-cially in the glass-metal hetero-bonding process.This study focuses on the analysis and experimental re-search of the bonding layer in the integrated structure.By optimizing the structural configuration and select-ing suitable bonding processes,the reliability of the telescope system is enhanced.The research indicates that using J-133 adhesive achieves the best performance,with a bonding layer thickness of 0.30 mm and a metal substrate surface roughness of Ra 0.8.These findings significantly enhance the reliability of the optical sys-tem while minimizing potential risks.展开更多
基金supported in part by the National Natural Science Foundation of China(Nos.12305349,12235006,12027812)Shenzhen Science and Technology Program(No.JSGGKQTD20210831174329010)Guangdong Basic and Applied Basic Research Foundation(No.2021TQ06Y108).
文摘This study aims to investigate the responses of a perovskite-based direct-conversion dual-layer flat-panel detector(DL-FPD)numerically.To this end,the X-ray sensitivity,spatial resolution quantified by the modulation transfer function(MTF),and detective quantum efficiency(DQE)of the DL-FPD are evaluated numerically using a linear cascade model.In addition,both the single-crystal(SC)and polycrystalline(PC)structures of MAPbI_(3)are investigated,along with various other key parameters such as the material thickness,electric field strength,X-ray beam spectrum,and electronic readout noise.The results demonstrate that SC perovskite consistently exhibits better performance than PC perovskite owing to fewer material defects.Increasing the layer thickness may decrease the MTF,but can also enhance the sensitivity and DQE.Moreover,appropriately increasing the external electric field within the material can improve the sensitivity,MTF,and DQE.Finally,reducing the electronic readout noise can significantly enhance the DQE for low-dose imaging.This study demonstrates the potential of high-quality dual-energy X-ray imaging using direct-conversion perovskite DL-FPDs.
基金supported by the Key R&D Program of Shandong Province(No.2023SFGC0101)Shandong Excellent Young Scientists Fund Program(Overseas)(No.2023HWYQ-047)+1 种基金the Natural Science Foundation of Shandong Province(No.ZR2022QA039)the National Natural Science Foundation of China(NSFC)(No.U2106202).
文摘Traditional digitizers for signal readout of PET detectors are based on commercial analog-to-digital converters(ADC).However,the cost and power consumption of an entire electronic readout system based on digitizers for a PET scanner are high.To address this problem,a soft-core ADC based on a field-programmable gate array(FPGA)was proposed.An FPGA-based ADC(FPGA-ADC)combines low loss and high performance.To achieve good performance,the FPGA-ADC requires three calibrations:time-to-digital converter(TDC)length calibration,TDC alignment calibration,and TDC-to-ADC calibration.A prototype front-end electronics based on FPGA-ADC was built to evaluate the performance of time-of-flight positron emission tomography(TOF PET)detectors.Each PET detector consists of a LYSO crystal single-ended coupled to a silicon photomultiplier(SiPM).The experimental results show that the full-width at half-maximum(FWHM)energy resolution for 511 keV gamma photons after saturation correction of the SiPM was 12.3%.The FWHM coincidence timing resolution(CTR)of the TOF PET detector with the readout of the front-end electronic prototype is 385.2 ps.FPGA-ADCbased front-end electronics are very promising for multichannel,low-cost,highly integrated,and power-efficient readout electronic systems for radiation detector applications.
基金supported by the National Natural Science Foundation of China(Nos.12175321,W2443004,11975021,11675275,U1932101)Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDA10010900)+2 种基金National Key Research and Development Program of China(Nos.2023YFA1606000 and 2020YFA0406400)National College Students Science and Technology Innovation ProjectUndergraduate Base Scientific Research Project of Sun Yat-sen University。
文摘Detector and event visualization are crucial components of high-energy physics(HEP)experimental software.Virtual reality(VR)technologies and multimedia development platforms,such as Unity,offer enhanced display effects and flexible extensibility for visualization in HEP experiments.In this study,we present a VR-based method for detector and event displays in the Jiangmen Underground Neutrino Observatory(JUNO)experiment.This method shares the same detector geometry descriptions and event data model as those in the offline software and provides the necessary data conversion interfaces.The VR methodology facilitates an immersive exploration of the virtual environment in JUNO,enabling users to investigate the detector geometry,visualize event data,and tune the detector simulation and event reconstruction algorithms.Additionally,this approach supports applications in data monitoring,physics data analysis,and public outreach initiatives.
基金supported by National Key R&D grant from the Ministry of Science and Technology of China(Nos.2021YFA1601600,2023YFA1606200)National Science Foundation of China(Nos.12090062,12105008)the Major State Basic Research Development Program of China.
文摘We present the preparation and measurement of the radioactive isotope^(37)Ar,which was produced using thermal neutrons from a reactor,as a calibration source for liquid xenon time projection chambers.^(37)Ar is a low-energy calibration source with a half-life of 35.01 days,making it suitable for calibration in the low-energy region of liquid xenon dark-matter experiments.Radioactive isotope^(37)Ar was produced by irradiating ^(36)Ar with thermal neutrons.It was subsequently measured in a gaseous xenon time projection chamber(GXe TPC)to validate its radioactivity.Our results demonstrate that^(37)Ar is an effective and viable calibration source that offers precise calibration capabilities in the low-energy domain of xenon-based detectors.
基金supported by the Strategic Priority Research Program of Chinese Academy of Sciences(Grant No.XDA0520403)Shanghai Municipal Science and Technology Major Project(Grant No.2019SHZDZX01)+1 种基金Innovation Program for Quantum Science and Technology(Grant No.2023ZD0300100)the National Natural Science Foundation of China(Grant Nos.U24A20320 and 62401554)。
文摘We here report a high system detection efficiency(SDE)superconducting single-photon detector(SSPD)at 2μm wavelength.The device integrates a SiO_(2)/Ta_(2)O_(5)distributed Bragg reflector(DBR)and a sandwich-structured double-layer NbN nanowire to enhance the optical absorption efficiency.A cold development technique is implemented to optimize the superconducting nanowires with sub-40-nm linewidths,thus enhancing the intrinsic detection efficiency(IDE).The fabricated SSPD shows an SDE exceeding 90% at 2μm wavelength.Moreover,the detector allows an operational working temperature of 2.2 K provided by a compact GM cryo-cooler.This detector delivers excellent performance at the 2μm wavelength,and its optimized structural design implies promising potential for extending detection toward longer infrared bands.It thus holds value for advancing high-sensitivity quantum technologies,mid-infrared optical communications,and dark matter detection research.
基金Under the auspices of the National Natural Science Foundation of China(No.42271224,41901193)Ministry of Edu cation Humanities and Social Sciences Research Planning Fund Project of China(No.24YJAZH190)+1 种基金Anhui Province Excellent Youth Research Project in Universities(No.2022AH030019)Anhui Social Sciences Innovation Development Research Project(No.2024CXQ503)。
文摘The accessibility of urban public transit directly influences residents’quality of life,travel behavior,and social equity.Its correlation with housing prices has garnered significant attention across disciplines such as geography,economics,and urban planning.Although much existing research focuses on the impact of individual transportation facilities on housing prices,there is a notable gap in comprehensive analyses that assess the influence of overall urban transit accessibility on housing market dynamics.This study selected the main urban area of Hefei,China,as a case to investigate the spatial distribution of housing prices and evaluate public transit accessibility in 2022.Employing techniques such as the optimized parameter geographical detector and local spatial regression models,the study aimed to elucidate the effects and underlying mechanisms of urban transit accessibility on housing prices.The findings revealed that:1)housing prices in Hefei exhibited a clustered spatial pattern,with high prices concentrated in the city center and lower prices in peripheral areas,forming three distinct high-price hotspots with a‘belt-like’distribution;2)public transit accessibility showed a‘coreperiphery’structure,with accessibility declining in a‘circumferential’pattern around the city center.Based on the‘housing price-accessibility’dimension,four categories were identified:high price-high accessibility(37.25%),high price-low accessibility(19.07%),low price-high accessibility(21.95%),and low price-low accessibility(21.73%);3)the impact of transit accessibility on housing prices was spatially heterogeneous,with bus travel showing the strongest explanatory power(0.692),followed by automobile,subway,and bicycle travel.The interaction of these transportation modes generated a synergistic effect on housing price differentiation,with most influencing factors contributing more than 25%.These findings offer valuable insights for optimizing the spatial distribution of public transit infrastructure and improving both urban housing quality and residents’living standards.
基金supports from the National Natural Science Foundation of China(22375220,U2001214,22471302)the Guangdong Basic and Applied Basic Research Foundation(2024B1515020101)Open Project Fund from State Key Laboratory of Optoelectronic Materials and Technologies(OEMT-2024-KF-08).
文摘Formamidinium lead iodide(FAPbI_(3))perovskite exhibits an impressive X-ray absorption coefficient and a large carrier mobility-lifetime product(μτ),making it as a highly promising candidate for X-ray detection application.However,the presence of larger FA^(+)cation induces to an expansion of the Pb-I octahedral framework,which unfortunately affects both the stability and charge carrier mobility of the corresponding devices.To address this challenge,we develop a novel low-dimensional(HtrzT)PbI_(3) perovskite featuring a conjugated organic cation(1H-1,2,4-Triazole-3-thiol,HtrzT^(+))which matches well with theα-FAPbI_(3) lattices in two-dimensional plane.Benefiting from the matched lattice between(HtrzT)PbI_(3) andα-FAPbI_(3),the anchored lattice enhances the Pb-I bond strength and effectively mitigates the inherent tensile strain of theα-FAPbI_(3) crystal lattice.The X-ray detector based on(HtrzT)PbI_(3)(1.0)/FAPbI_(3) device achieves a remarkable sensitivity up to 1.83×10^(5)μC Gy_(air)^(−1) cm^(−2),along with a low detection limit of 27.6 nGy_(air) s^(−1),attributed to the release of residual stress,and the enhancement in carrier mobility-lifetime product.Furthermore,the detector exhibits outstanding stability under X-ray irradiation with tolerating doses equivalent to nearly 1.17×10^(6) chest imaging doses.
基金supported by the NSFC under Grant No.62474169the National Key Research and Development Program of China under Grant No.2024YFB3212200the funding from USTC under Grant Nos.WK2100000025,KY2190000003,and KY2190000006。
文摘Soft X-ray detectors play a vital role in materials science,high-energy physics and medical imaging.Cs_(2)AgBiBr_(6),a lead-free double perovskite,has gained attention for its excellent optoelectronic properties,stability,and nontoxicity.However,its fast crystallization and requirement for high-temperature annealing(>250℃)often lead to inferior film quality,limiting its application in flexible devices.This study introduces an alloying strategy that significantly improves the quality of Cs_(2)AgBiBr_(6)thin films annealed at a reduced temperature of 150℃.Devices based on the alloyed thin films exhibit an ultra-low dark current of 0.32 nA·cm^(-2)and a quantum efficiency of 725%.Furthermore,the first successful integration of Cs_(2)AgBiBr_(6)with a thinfilm transistor backplane demonstrates its superior imaging performance,indicating that Cs_(2)AgBiBr_(6)is a promising material for next-generation soft X-ray sensors.
文摘Numerous sectors,such as education,the IT sector,and corporate organizations,transitioned to virtual meetings after the COVID-19 crisis.Organizations now seek to assess participants’fatigue levels in online meetings to remain competitive.Instructors cannot effectively monitor every individual in a virtual environment,which raises significant concerns about participant fatigue.Our proposed system monitors fatigue,identifying attentive and drowsy individuals throughout the online session.We leverage Dlib’s pre-trained facial landmark detector and focus on the eye landmarks only,offering a more detailed analysis for predicting eye opening and closing of the eyes,rather than focusing on the entire face.We introduce an Eye Polygon Area(EPA)formula,which computes eye activity from Dlib eye landmarks by measuring the polygonal area of the eye opening.Unlike the Eye Aspect Ratio(EAR),which relies on a single distance ratio,EPA adapts to different eye shapes(round,narrow,or wide),providing a more reliable measure for fatigue detection.The VMFD system issues a warning if a participant remains in a fatigued condition for 36 consecutive frames.The proposed technology is tested under multiple scenarios,including low-to high-lighting conditions(50-1400 lux)and both with and without glasses.This study builds an OpenCV application in Python,evaluated using the iBUG 300-W dataset,achieving 97.5%accuracy in detecting active participants.We compare VMFD with conventional methods relying on the EAR and show that the EPA technique performs significantly better.
基金Supported by the National Natural Science Foundation of China under Grant Nos U0934001 and 11076028the Science and Technology Commission of Shanghai Municipality under Grant Nos 11DZ1140202 and 13XD1425400the Pudong New Area Science and Technology Development Fund of China under Grant No PKJ2012-D04
文摘A phase-sensitive optical time domain reflectometer （φ-OTDR） based on a 120°-phase-difference Michelson in- terferometer is proposed. The Michelson interferometer with arm difference of 4m is used to test the phase difference between the Rayleigh scattering from two sections of the fiber. A new demodulation method called the inverse transmission matrix demodulation scheme is utilized to demodulate the distributed phase from the backward scattering along the long fiber, The experimental results show that the 120°-phase-difference inter- ferometer φ-OTDR can detect the phase along the 3km fiber, and the acoustic signal within the whole human hearing range of 20 Hz-20 kHz is reproduced accurately and quickly.
基金Project partially supported by the National Natural Science Foundation of China (Grant Nos 10527003 and 60672104)the State Key Development Program for Basic Research of China (Grant No 2006CB705700-05)+1 种基金Joint Research Foundation of Beijing Education Committee (Grant No SYS100010401)Beijing Natural Science Foundation (Grant No 3073019)
文摘Robust and fast fat suppression is a challenge in balanced steady-state free precession （SSFP） magnetic resonance imaging. Although single-acquisition phase-sensitive SSFP can provide fat-suppressed images in short scan time, phase errors, especially spatially-dependent phase shift, caused by a variety of factors may result in misplacement of fat and water voxels. In this paper, a novel phase correction algorithm was used to calibrate those phase errors during image reconstruction. This algorithm corrects phase by region growing, employing both the magnitude and the phase information of image pixels. Phantom and in vivo imagings were performed to validate the technique. As a result, excellent fat-suppressed images were acquired by using single-acquisition phase-sensitive SSFP with phase correction.
基金Supported by Haikou Key Science and Technology Project (2012-075)Haikou Science and Technology Planning Project(2009-049-1)Science and Technology Fund of Haikou Health Bureau(2010-SWY-13-058)
文摘Objective:Late gadolinium enhancement(LGE) patterns of cardiovascular magnetic resonance (CMR) relying on PSIR(phase-sensitive inversion recovery sequence) techniques had been used to determine the characteristics of LGE in apical hypertrophic cardiomyopathy(ApHCM). Methods:Forty patients pure ApHCM[age,(60.2±10.4) years,31 men]were enrolled.LGE images were acquired using PSIR,and analyzed using a 17-segment model.Summing the LGE areas in all short axis slices yielded the total volume of late enhancement,which was subsequently presented as a proportion of total LV myocardium(%LGE).Results:Mean maximal apical wall thickness was(17.9±2.3) mm,and mean left ventricular(LV) ejection fraction was(67.7±8.0)%.LGE was detected in 130 segments of 30 patients(75.0%),occupying(4.9±5.5)% of LV myocardium.LGE was mainly detected at the junction between left and right ventricles in 12(30%) and at the apex in 28(70%),although LGE-positive areas were widely distributed,and not limited to the apex.Focal LGE at the non-hypertrophic LV segments was found in some ApHCM patients,even without LGE of hypertrophied apical segments.Conclusions:LGE was frequently observed not only in the thickened apex of the heart but also in other LV segments,irrespective of the presence or absence of hypertrophy.The simple presence of LGE on CMR was not representative of adverse prognosis in this population.
基金supported by Haikou Key Science and Technology Project (2012-075)Haikou Science and Technology Planning Project(2009-049-1)Science and Technology Fund of Haikou Health Bureau(2010-SWY-13-058)
文摘Objective:To determine the deference between phase sensitive magnetic resonance(MR) imaging and magnitude reconstruction to detect infracted myocardium.Methods:Twenty patients(16 men;4 women;mean age,56 years),experienced Q-wave myocardial infarction 2 weeks earlier were examined with a 3.0-T MR system 10 minutes after administration of 0.1 mmol/kg body weight gadobenate dimeglumine.To determine the optimal TI,a TI scout sequence was used.A segmented 2D IR true fast imaging with steady-state precession(trueFISP) sequence that produces both phase-sensitive and magnitude-reconstructed images were used at TI values of 200-600 msec(TI values were varied in 100-msec steps) and at optimal TI(mean value,330 msec).Contrast- noise ratios(CNRs) of normal and infarcted myocardium and the area of infarcted myocardium were determined.Two-tailed unpaired sample Student t test was used to compare CNRs,and area of infarction.Results:MMean CNR phase-sensitive and magnitude-reconstructed images at optimal TI(mean value,330 msec) were 6.2,and 6.1,respectively.For a TI of 200 msec,CNR values were 5.5,and 4.2,respectively;for TI of 600 msec,CNR values were 5.8 and 4.3,respectively.Area of infarcted myocardium was underestimated on magnitude-reconstruction images(P = 0.002-0.03) for short TI values(ie.,200 msec) but not on phase sensitive reconstructed when compared with IR tureFISP images obtained at optimal TI.Conclusions: LPhase-sensitive image reconstruction results in reduced need for precise choice of TI and more consistent image quality.
基金Project supported by the National Natural Science Foundation of China(Grant Nos60308002and60678005)the Foundation for the Author of National Excellent Doctoral Dissertation of China(Grant No200339)+2 种基金the Foundation for Key Program of Ministry of Education,China(Grant No105156)the Fok Ying-Tong Education Foundation for Young Teachers in the Higher Education Institutions of China(Grant No101061)the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No20050698017)
文摘We study the colour-locked twin-noisy-field correlation effects in the fifth-order nonlinear susceptibility of ultrafast polarization beats in a cascade four-level system. More importantly, the fifth-order phase-sensitive heterodyne detection of ultrafast polarization beats has been exploited. The fifth-order nonlinear optical response can be controlled and modified through the colour-locked correlation of twin noisy fields. Thus, this method with the phase dispersion information is a good way to measure the real and imaginary parts of the fifth-order nonlinear susceptibility.
基金Project supported by National Natural Science Foundation of China(Grant Nos.11704053 and 52175531)the Science and Technology Research Program of Chongqing Municipal Education Commission(Grant No.KJQN201800629)。
文摘We present a theoretical scheme for broadband multi-channel quantum noise suppression and phase-sensitive modulation of continuous variables in a coupled resonant system with quantum entanglement properties.The effects of different coupling strengths,pumping power in suppressing quantum noise and controlling the width of quantum interference channels are analyzed carefully.Furthermore,quantum noise suppression at quadrature amplitude is obtained with phase-sensitive modulation.It shows that the entanglement strength of the output field and the quantum noise suppression effect can be enhanced significantly by a strong pumping filed due to interaction of pumping light with the nonlinear crystal.The full width at half maxima(FWHM)of the noise curve at the resonant peak(△=0 MHz)is broadened up to 2.17 times compared to the single cavity.In the strong coupling resonant system,the FWHM at △=0 MHz(△=±3.1 MHz)is also broadened up to 1.27(3.53)times compared to the weak coupling resonant system case.The multi-channel quantum interference creates an electromagnetically induced transparent-like line shape,which can be used to improve the transmission efficiency and stability of wave packets in quantum information processing and quantum memory.
基金supported by the National Natural Science Foundation of China(No.12235006)the National Key Research and Development Program of China(No.2020YFE0202002.
文摘X-ray detectors show potential applications in medical imaging,materials science,and nuclear energy.To achieve high detection efficiency and spatial resolution,many conventional semiconductor materials,such as amorphous selenium,cadmium telluride zinc,and perovskites,have been utilized in direct conversion X-ray detectors.However,these semiconductor materials are susceptible to temperature-induced performance degradation,crystallization,delamination,uneven lattice growth,radiation damage,and high dark current.This study explores a new approach by coupling an FC40 electronic fluorinated liquid with a specialized high-resolution and high-readout-speed complementary metal-oxide-semiconductor(CMOS)pixel array,specifically the Topmetal II−chip,to fabricate a direct conversion X-ray detector.The fluorinated liquid FC40(molecular formula:C_(21)F_(48)N_(2))is an electronic medium that is minimally affected by temperature and displays no issues with uniform conductivity.It exhibits a low dark current and minimal radiation damage and enables customizable thickness in X-ray absorption.This addresses the limitations inherent in conventional semiconductor-based detectors.In this study,simple X-ray detector imaging tests were conducted,demonstrating the excellent coupling capability between FC40 electronic fluorinated liquid and CMOS chips by the X-ray detector.A spatial resolution of 4.0 lp/mm was measured using a striped line par card,and a relatively clear image of a cockroach was displayed in the digital radiography imaging results.Preliminary test results indicated the feasibility of fabricating an X-ray detector by combining FC40 electronic fluorinated liquid and CMOS chips.Owing to the absence of issues related to chip-material coupling,a high spatial resolution could be achieved by reducing the chip pixel size.This method presents a new avenue for studies on novel liquid-based direct conversion X-ray detectors.
基金supported by the National Natural Science Foundation of China(12125505).
文摘The PICOSEC Micromegas(MM)is a precise timing gaseous detector based on a Cherenkov radiator coupled with a semi-transparent photocathode and an MM amplifying structure.It features a two-stage amplification process that leads to a significant deterioration of non-uniformity when scaling up to larger areas.Since the performance of gaseous detectors is highly dependent on the choice of working gas,optimizing the gas mixture offers a promising solution to improve the uniformity performance.This paper addresses these challenges through a combined approach of simulation based on Garfield++and experimental studies.The simulation investigates the properties of different mixing fractions of gas mixtures and their impact on detector performance,including gain uniformity and time resolution.To verify the simulation results,experimental tests were conducted using a multi-channel PICOSEC MM prototype with different gas mixtures.The experimental results are consistent with the findings of the simulation,indicating that a higher concentration of neon significantly improves the detector’s gain uniformity.Furthermore,the influence of gas mixtures on time resolution was explored as a critical performance indicator.The study presented in this paper offers valuable insights for improving uniformity in large-area PICOSEC MM detectors and optimizing overall performance.
基金Supported by the National key R&D Program of China(2022YFB3903103,2023YFC3081100)。
文摘Despite rapid advancements in lidar technology,extremely long-range observation remains a signifi⁃cant challenge.Recently,2μm lasers have demonstrated a potential to be applied in CDWL(Coherent Doppler Wind Lidar)system,for its high atmospheric penetration capability through the atmosphere and high potential la⁃ser power.In this study,we present a 2μm balanced detector that consists of a pair of commercial positive-intrin⁃sic-negative(PIN)diodes with a low-noise transimpedance circuit.To meet the high bandwidth requirements,the highspeed transimpedance circuit and bias voltage tuning method were utilized to overcome the large capaci⁃tance of PIN diodes.The circuit transfer function,stability analysis and noise calculation have been studied.The detector was co-packaged with a data acquisition module for convenient data transmission and bias voltage con⁃trol.The characteristics of the detector,including bandwidth,noise and bias voltage influence,are evaluated in laboratory.Results show that the RMS value of the balanced detector background noise is 539μV and the band⁃widths of the two diodes are 110.8 MHz and 110.3 MHz,respectively.The evaluation results show that the bal⁃anced detector meets the wind measurement requirements and allows for a 1.45×increase in bandwidth through bi⁃as voltage tuning.Our work offers insights into lidar detector design and bandwidth enhancement,providing a valuable reference for researchers and professionals in the field.More importantly,it lays a critical foundation for fu⁃ture ultra-long-range and space-borne 2μm coherent wind lidar systems by addressing key device-level challenges.
文摘To detect space gravitational waves in the extremely low-frequency band,the telescope and optic-al platform require high stability and reliability.However,the cantilevered design presents challenges,espe-cially in the glass-metal hetero-bonding process.This study focuses on the analysis and experimental re-search of the bonding layer in the integrated structure.By optimizing the structural configuration and select-ing suitable bonding processes,the reliability of the telescope system is enhanced.The research indicates that using J-133 adhesive achieves the best performance,with a bonding layer thickness of 0.30 mm and a metal substrate surface roughness of Ra 0.8.These findings significantly enhance the reliability of the optical sys-tem while minimizing potential risks.
