Diamond-like carbon （DLC） thin film is one of the most widely used optical thin films. The fraction of chemical bondings has a great influence on the properties of the DLC film. In this work, DLC thin films are prep...Diamond-like carbon （DLC） thin film is one of the most widely used optical thin films. The fraction of chemical bondings has a great influence on the properties of the DLC film. In this work, DLC thin films are prepared by ion-beam sputtering deposition in Ar and CH4 mixtures with graphite as the target. The influences of the ion-beam voltage on the surface morphology, chemical structure, mechanical and infrared optical properties of the DLC films are investigated by atomic force microscopy （AFM）, Raman spectroscopy, nanoindentation, and Fourier transform infrared （FTIR） spec- troscopy, respectively. The results show that the surface of the film is uniform and smooth. The film contains sp2 and sp3 hybridized carbon bondings. The film prepared by lower ion beam voltage has a higher sp3 bonding content. It is found that the hardness of DLC films increases with reducing ion-beam voltage, which can be attributed to an increase in the fraction of sp3 carbon bondings in the DLC film. The optical constants can be obtained by the whole infrared optical spectrum fitting with the transmittance spectrum. The refractive index increases with the decrease of the ion-beam voltage, while the extinction coefficient decreases.展开更多
Perovskite solar cells(PSCs) have become a hot topic in the field of renewable energy due to their excellent power conversion efficiency and potential for low-cost manufacturing. The hole transport layer(HTL), as a ke...Perovskite solar cells(PSCs) have become a hot topic in the field of renewable energy due to their excellent power conversion efficiency and potential for low-cost manufacturing. The hole transport layer(HTL), as a key component of PSCs,plays a crucial role in the cell's overall performance. Magnetron sputtering NiO_(x) has attracted widespread attention due to its high carrier mobility, excellent stability, and suitability for large-scale production. Herein, an insightful summary of the recent progress of magnetron sputtering NiO_(x) as the HTL of PSCs is presented to promote its further development. This review summarized the basic properties of magnetron sputtering NiO_(x) thin film, the key parameters affecting the optoelectronic properties of NiO_(x) thin films during the magnetron-sputtering process, and the performance of the corresponding PSCs. Special attention was paid to the interfacial issues between NiO_(x) and perovskites, and the modification strategies were systematically summarized. Finally, the challenges of sputtering NiO_(x) technology and the possible development opportunities were concluded and discussed.展开更多
The discharge and plasma characteristics of Ag magnetron sputtering discharge operated near the electron series resonance(ESR)oscillation,which was excited using the driving frequency of 27.12 MHz,was investigated.The...The discharge and plasma characteristics of Ag magnetron sputtering discharge operated near the electron series resonance(ESR)oscillation,which was excited using the driving frequency of 27.12 MHz,was investigated.The imaginary part of impedance was found to undergo a transition from capacitive to inductive on varying radio-frequency(RF)power,and the conditions for the ESR excitation were satisfied.The current–voltage(I–V)characteristic of discharge showed that the lower discharge voltage with higher current was an important feature of RF magnetron sputtering operated near the ESR oscillation,which was caused by the small impedance Z originated from the mutual compensation between the sheath capacitive reactance and the plasma inductive reactance.The higher electron temperature,ion flux density and ion energy as well as the moderate electron density were obtained.The interaction of higher energy ions on substrate surface improved the crystallographic quality of Ag films.Therefore,the 27.12 MHz magnetron sputtering operated near the ESR oscillation has better deposition characteristics than that of commercial 13.56 MHz RF magnetron sputtering.展开更多
Silver is an elegant white precious metal,but it is easily oxidized by O3,SO2,and H2S in the air,turning yellow or dark,which affects its decorative effect.The existing silver coating,primarily prepared through the el...Silver is an elegant white precious metal,but it is easily oxidized by O3,SO2,and H2S in the air,turning yellow or dark,which affects its decorative effect.The existing silver coating,primarily prepared through the electroplating process,poses serious environmental pollution problems.It is necessary to seek new,green,and environmentally friendly coating processes while also enhancing the color palette of silver jewelry coatings.Titanium film layers were deposited on Ag925 and Ag999 surfaces using magnetron sputtering coating technology.The effects of sputtering time,substrate surface state,reaction gas type and time,and film thickness on the color of the film layers were studied,and the anti discoloration performance of the obtained film layers under the optimal process was tested.The experimental results show that when the sputtering time varies from 5 to 10 minutes,injecting argon,oxygen,and nitrogen into the coating chamber yields rich colors such as purple with a red tint,blue,yellow green,yellowish purple,and blue purple.The precise control of gas injection time has a significant impact on the color of the film layer.In terms of anti tarnish performance,the film showed good stability in the artificial sweat immersion test.From an environmental perspective,the magnetron sputtering titanium film process has no harmful gas or liquid emissions,which aligns with the sustainable development trend of the jewelry industry and holds great promise for application.This study has improved the visual effect and practical performance of the product,providing important theoretical basis and experimental data support for the application of environmentally friendly silver surface vacuum magnetron sputtering titanium thin film coating technology.展开更多
Ammonium dinitramide(ADN),as a high-energy oxidizer widely applied in the field of rocket and missile propellants,has a prominent issue of high hygroscopicity due to its strong polarity.The previous coating encapsulat...Ammonium dinitramide(ADN),as a high-energy oxidizer widely applied in the field of rocket and missile propellants,has a prominent issue of high hygroscopicity due to its strong polarity.The previous coating encapsulation methods have struggled to address the problems of uneven coating and polarity mismatch.This research innovatively introduces perfluorooctanoic acid(PFOA)as a polar transition intermediate layer.Utilizing the polarity of one end of it to adsorb on the surface of ADN through hydrogen bonds,the problem of polarity mismatch is effectively overcome.Meanwhile,the vibrational magnetron sputtering process has been first applied in the energetic field,with a special vibrating abutment enhancing ADN particle fluidity to solve coating non-uniformity,thus preparing prilled ADN@PFOA@PTFE core-dual-shell composites.Performance tests reveal that this composite material possesses excellent hydrophobic and anti-hygroscopic properties.When left at 25℃and 75%RH for 3 days,moisture absorption was reduced by more than 90%compared to pure ADN.Simultaneously,its thermal stability,heat release performance,and combustion performance have been improved.The research achievements optimize the storage conditions of ADN in the application of rocket and missile propellants,providing solid support and broad development prospects for technological innovation in military fields.展开更多
Ensuring high electrocatalytic performance simultaneously with low or even no precious-metal usage is still a big challenge for the development of electrocatalysts toward oxygen evolution reaction(OER)in anion exchang...Ensuring high electrocatalytic performance simultaneously with low or even no precious-metal usage is still a big challenge for the development of electrocatalysts toward oxygen evolution reaction(OER)in anion exchange membrane water electrolysis.Here,homogeneous high entropy oxide(HEO)film is in-situ fabricated on nickel foam(NF)substrate via magnetron sputtering technology without annealing process in air,which is composed of many spinel-structured(FeCoNiCrMo)_(3)O_(4) grains with an average particle size of 2.5 nm.The resulting HEO film(abbreviated as(FeCoNiCr-Mo)_(3)O_(4))exhibits a superior OER performance with a low OER overpotential of 216 mV at 10 mA cm^(–2) and steadily operates at 100 mA cm^(–2) for 200 h with a decay of only 272μV h^(–1),which is far better than that of commercial IrO_(2) catalyst(290 mV,1090μV h^(–1)).Tetramethylammonium cation(TMA^(+))probe experiment,activation energy analysis and theoretical calculations unveil that the OER on(FeCoNiCrMo)_(3)O_(4) follows an adsorbate evolution mechanism pathway,where the energy barrier of rate-determining step for OER on(FeCoNiCrMo)_(3)O_(4) is substantially lowered.Also,methanol molecular probe experiment suggests that a weakened ^(*)OH bonding on the(FeCoNiCrMo)_(3)O_(4) surface and a rapid deprotonation of ^(*)OH,further enhancing its OER performance.This work provides a feasible solution for designing efficient high entropy oxides electrocatalysts for OER,accelerating the practical process of water electrolysis for H2 production.展开更多
In the past few decades,ion engines have been widely used in deep-space propulsion and satellite station-keeping.The aim of extending the thruster lifetime is still one of the most important parts during the design st...In the past few decades,ion engines have been widely used in deep-space propulsion and satellite station-keeping.The aim of extending the thruster lifetime is still one of the most important parts during the design stage of ion engine.As one of the core components of ion engine,the grid assembly of ion optic systems may experience long-term ion sputtering in extreme electro-thermal environments,which will eventually lead to its structural and electron-backstreaming failures.In this paper,the current studies of the grid assembly erosion process are systematically analyzed from the aspects of sputtering damage process of grid materials,numerical simulations,and measurements of erosion characteristics of grid assembly.The advantages and disadvantages of various erosion prediction models are highlighted,and the key factors and processes affecting the prediction accuracy of grid assembly erosion patterns are analyzed.Three different types of experimental methods of grid assembly erosion patterns are compared.The analysis in this paper is of great importance for selecting the sputter-resistant grid materials,as well as establishing the erosion models and measurement methods to accurately determine the erosion rate and failure modes of grid assembly.Consequently,the working conditions and structure parameters of ion optic systems could be optimized based on erosion models to promote the ion engine lifetime.展开更多
Ta-doped SnO_(2)(TTO)is a suitable candidate to replace transparent conductive oxide(TCO)composed of expensive indium used for optoelectronics and silicon heterojunction solar cells fabricated below 200℃.However,TTO ...Ta-doped SnO_(2)(TTO)is a suitable candidate to replace transparent conductive oxide(TCO)composed of expensive indium used for optoelectronics and silicon heterojunction solar cells fabricated below 200℃.However,TTO films fabricated by sputtering at low temperature still demonstrate too high resistance and optical absorptance for application in industry.In this study,we investigate the influence of sputtering ambient on the optoelectrical properties of TTO films.The addition of hydrogen and oxygen to argon during sputtering leads to a large improvement in the optoelectrical properties of TTO films.The best TTO film has a low average absorptance of 1.9%and a low resistance of 3.8×10^(-3)Ω·cm with a high carrier density of 9.3×10^(19)cm^(-3)and mobility of 17.8 cm^(2)·V^(-1)·s^(-1).The micros tructural and compositional properties of TTO films were characterized using x-ray diffraction,x-ray photoelectron spectroscopy and UV-Vis spectrophotometry.A proper ratio of hydrogen to oxygen in the sputtering gas improves the crystallinity and the doping efficiency of Ta.Optical absorptance is also reduced with suppressed formation of Sn(Ⅱ)in the TTO films.Therefore,our findings exhibit remarkable potential for the industrial application of TTO as a low-cost TCO.展开更多
Atmospheric escape plays a critical role in shaping the long-term climate evolution of Mars.Among the various escape mechanisms,energetic neutral atoms(ENAs)generated through charge exchange between solar wind ions an...Atmospheric escape plays a critical role in shaping the long-term climate evolution of Mars.Among the various escape mechanisms,energetic neutral atoms(ENAs)generated through charge exchange between solar wind ions and exospheric neutrals serve as an important diagnostic for ion-neutral interactions and upper atmospheric loss.This study presents direct observations of hydrogen ENAs(H-ENAs)on the dayside of Mars by using the Mars Ion and Neutral Particle Analyzer(MINPA)onboard China’s Tianwen-1 orbiter.By analyzing H-ENA data during a coronal mass ejection and a stream interaction region from December 29,2021,to January 1,2022,and comparing these data with MAVEN/SWIA(Mars Atmosphere and Volatile EvolutioN/Solar Wind Ion Analyzer)solar wind measurements,we examine the temporal evolution of H-ENA flux and the associated sputtered escape of atmospheric constituents.The observed H-ENA velocity is consistent with upstream solar wind ions,and the H-ENA-to-ion intensity ratio is used to infer variations in exospheric density,revealing a delayed response to enhanced solar wind activity.Penetrating H-ENA intensities reach up to 5.3×10^(6)s^(−1) cm^(−2),with energy fluxes on the order of(0.5-8.1)×10^(−3) mW/m^(2).The estimated oxygen sputtered escape rate driven by penetrating H-ENAs ranges from 5.5×10^(23)s^(−1) to 5.2×10^(24)s^(−1),comparable to or exceeding previous estimates based on penetrating ions.The findings highlight the need for low-altitude H-ENA observations to better quantify their atmospheric interactions and refine our understanding of nonthermal escape processes at Mars.展开更多
One of the primary concerns associated with ion cyclotron resonance heating(ICRH)is the enhanced impurity sputtering resulting from radio frequency(RF)sheath formation near plasma-facing components(PFCs),such as limit...One of the primary concerns associated with ion cyclotron resonance heating(ICRH)is the enhanced impurity sputtering resulting from radio frequency(RF)sheath formation near plasma-facing components(PFCs),such as limiters.Developing a sputtering model integrated with RF sheath simulations allows for a more comprehensive understanding of the kinetic behavior of incident ions and their interactions with the limiter surface.We accordingly develop an impurity sputtering model“PMSAD”,which computes the sputtering yield(amount of impurity)on the limiter surface based on incident ion characteristics and predicts the spatial distribution of impurities.The model provides a robust method for understanding and analyzing the impurity sputtering process from limiter surfaces,which is crucial for preventing ICRH surface erosion and reducing edge and core plasma contamination.展开更多
One-dimensional ZnO nanorods are synthesized by ox idating thin metal zinc films deposited on Si(111) substrates with radio frequen cy magnetron sputtering.The crystal structure,surface morphology,and optical pro per...One-dimensional ZnO nanorods are synthesized by ox idating thin metal zinc films deposited on Si(111) substrates with radio frequen cy magnetron sputtering.The crystal structure,surface morphology,and optical pro perties of nanorods are investigated.X-ray diffraction(XRD) pattern,scanning el ectron microscopy(SEM),and transmission electron microscopy(TEM) analyses show t hat the synthesized single-crystal ZnO nanorods develop like hairpins along dif ferent radials,with a hexagonal wurtzite structure.The diameters of nanorods ran ge between 30 and 60nm and lengths up to micrometers.Photoluminescence(PL) analy sis shows that,under 280nm light excitation,a strong and sharp near band-edge U V light emission band at 372nm and a relatively weak green deep-level light emi ssion band at 516nm are observed from the ZnO nanorods,which indicates excellent crystallization and optical quality of the fabricated ZnO nanorods.展开更多
Al-doped ZnO thin films were prepared on glass substrate using an ultra-high density target by RF magnetron sputtering at room temperature. The microstructure, surface morphology, optical and electrical properties of ...Al-doped ZnO thin films were prepared on glass substrate using an ultra-high density target by RF magnetron sputtering at room temperature. The microstructure, surface morphology, optical and electrical properties of AZO thin films were investigated by X-ray diffractometer, scanning electron microscope, UV-visible spectrophotometer, four-point probe method, and Hall-effect measurement system. The results showed that all the films obtained were polycrystalline with a hexagonal structure and average optical transmittance of AZO thin films was over 85 % at different sputtering powers. The sputtering power had a great effect on optoelectronic properties of the AZO thin films, especially on the resistivity. The lowest resistivity of 4.5×10^-4 Ω·cm combined with the transmittance of 87.1% was obtained at sputtering power of 200 W. The optical band gap varied between 3.48 and 3.68 eV.展开更多
In order to study the effect of the microstructure with Al and V added TiN coatings, TiN, TiAlN and TiAlVN coatings were deposited on AISI M2 high-speed steels by magnetron reactive sputtering. The microstructures of ...In order to study the effect of the microstructure with Al and V added TiN coatings, TiN, TiAlN and TiAlVN coatings were deposited on AISI M2 high-speed steels by magnetron reactive sputtering. The microstructures of all the coatings were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results indicate that the addition of Al into TiN coatings reduces their lattice constant, but a further addition of V into TiAlN coatings increases their lattice constant. Moreover, the growth morphologies for TiN, TiAlN, and TiAlVN indicate that adding Al and V has a tendency to improve the columnar structure. The (111) and (200) orientations of TiN, TiAlN, and TiAlVN are identified. Theε(Fe3N-Fe2N) phase occurs because a small amount of Fe is present in the coatings. The interlayers of TiAlN and TiAlVN have the preferred (01 1 0) orientation. The texture (columnar) structure of the (111) and (200) orientations is observed in the TiAlN and TiAlVN coatings. An orientation relationship of (01 1 0)α-Ti//(110)T.M occurs between the interlayer and tempered martensite (T.M) in TiAlVN.展开更多
Wurtzite aluminum nitride（AlN） films were deposited on Si（100） wafers under various sputtering pressures by radio-frequency（RF） reactive magnetron sputtering. The film properties were investigated by XRD, SEM, A...Wurtzite aluminum nitride（AlN） films were deposited on Si（100） wafers under various sputtering pressures by radio-frequency（RF） reactive magnetron sputtering. The film properties were investigated by XRD, SEM, AFM, XPS and nanoindenter techniques. It is suggested from the XRD patterns that highly c-axis oriented films grow preferentially at low pressures and the growth of（100） planes are preferred at higher pressures. The SEM and AFM images both reveal that the deposition rate and the surface roughness decrease while the average grain size increases with increasing the sputtering pressure. XPS results show that lowering the sputtering pressure is a useful way to minimize the incorporation of oxygen atoms into the AlN films and hence a film with closer stoichiometric composition is obtained. From the measurement of nanomechanical properties of AlN thin films, the largest hardness and elastic modulus are obtained at 0.30 Pa.展开更多
Nano-scaled ZrNbAlN films with different negative bias voltages（Vb） were deposited on bronze substrate and Si（100） wafers by a reactive unbalanced magnetron sputtering technique. Composition and structure properti...Nano-scaled ZrNbAlN films with different negative bias voltages（Vb） were deposited on bronze substrate and Si（100） wafers by a reactive unbalanced magnetron sputtering technique. Composition and structure properties were characterized by X-ray photoelectron spectroscopy and X-ray diffraction. It is found that mole concentrations of Zr and Nb are affected by Vb, which leads to the increase of binding energy of N 1s and Al 2p and decrease of binding energy of Zr 3d5/2 and Nb 3d5/2. Surface morphologies evolution controlled by Vb could be observed. Furthermore, X-ray diffraction patterns reveal that these films show a（111） preferred orientation. Moreover, mechanical property and corrosion behavior of ZrNbAlN films were characterized by nanoindentation test and corrosion test, respectively. A maximum value of 21.85 GPa at-70 V occurs in the ZrNbAlN- bronze system, which outperforms uncoated bronze. Corrosion experiments in 0.5 mol/L NaCl and 0.5 mol/L HCl solution show that corrosion potential and corrosion current are dependent on Vb, and better anti-corrosion property could be obtained at-90 V.展开更多
A kind of W/DLC/W-S-C composite film was fabricated by magnetron sputtering method.Effects of WSx content on the structure and the adhesion of the composite films were investigated.In addition,tribological behavior of...A kind of W/DLC/W-S-C composite film was fabricated by magnetron sputtering method.Effects of WSx content on the structure and the adhesion of the composite films were investigated.In addition,tribological behavior of the composite films was studied in the conditions of the ambient air and N2 gas atmosphere by ball-on-disk tester.The results indicate that the composite films show dense and amorphous microstructure.The WCx and WSx compounds are found in amorphous diamond like carbon matrix in the top layers of W-S-C.A proper WSx content is beneficial for improving the adhesion of the composite films.In air atmosphere,the composite films with high C content have better wear resistance and the friction coefficients range from 0.15 to 0.25.In N2 condition,high WSx content is benefit for the wear resistance and the friction coefficients of the composite films range from 0.03 to 0.1.展开更多
Zinc nitride （Zn3N2） thin films were prepared by radio frequency （RF） magnetron sputtering on quartz glass at different substrate temperatures.The structure and composition were characterized by X-ray diffraction ...Zinc nitride （Zn3N2） thin films were prepared by radio frequency （RF） magnetron sputtering on quartz glass at different substrate temperatures.The structure and composition were characterized by X-ray diffraction and Raman-scattering measurements,respectively.The polycrystalline phase Zn3N2 films appeared when the ratio of the N2 partial pressure to the total pressure reached 1/2.The effects of the substrate temperature on the electrical and optical properties of the Zn3N2 films were investigated by Hall measurements and optical transmission spectra.The electrical and optical properties of the films were highly dependent on the substrate temperature.With the substrate temperature increasing from 100 to 300℃,the resistivity of the Zn3N2 films decreased from 0.49 to 0.023Ω·cm,the carrier concentration increased from 2.7×10^16 to 8.2×10^19cm^-3,and the electron mobility decreased from 115 to 32cm^2/（V·s）.The deposited Zn3N2 films were considered to be n-type semiconductors with a direct optical band gap,which was around 1.23eV when the substrate temperature was 200℃.展开更多
Microstructure of GaAs/SiO 2 nanogranular thin films fabricated by radio frequency magnetron co sputtering technique and postannealing are investigated via atomic force microscope,X ray diffraction,and Rutherford b...Microstructure of GaAs/SiO 2 nanogranular thin films fabricated by radio frequency magnetron co sputtering technique and postannealing are investigated via atomic force microscope,X ray diffraction,and Rutherford backscattering spectroscopy.The results show that GaAs nanocrystals with average diameters from 1 5nm to 3 2nm (depending on the annealing temperature) are uniformly dispersed in the SiO 2 matrices.GaAs and SiO 2 are found in normal stoichiometry in the films.The nonlinear optical refraction and nonlinear optical absorption are studied by Z scan technique using a single Gaussian beam of pulse laser.The third order nonlinear optical refractive index and nonlinear absorption coefficient are enhanced due to the quantum confinement effects and estimated to be 4×10 -12 m 2/W and 2×10 -5 m/W respectively in nonresonant condition,while 2×10 -11 m 2/W and -1×10 -4 m/W respectively in quasi resonant condition.展开更多
Immiscible Cu-W alloy thin films were prepared using dual-target magnetron sputtering deposition process. The structure evolution of Cu-W thin films during preparation was investigated by X-ray diffraction, transmissi...Immiscible Cu-W alloy thin films were prepared using dual-target magnetron sputtering deposition process. The structure evolution of Cu-W thin films during preparation was investigated by X-ray diffraction, transmission electron microscopy and high resolution transmission electron microscopy. In the initial stage of dual-target magnetron sputtering deposition process, an amorphous phase formed; then it crystallized and the analogy spinodal structure formed due to the bombardment of the sputtered particles during sputtering deposition process, the surface structure of the film without the bombardment of the sputtered particles was the amorphous one, the distribution of the crystalline and amorphous phase showed layer structure. The solid solubility with the analogy spinodal structure was calculated using the Vegard law. For Cu-13.7%W （mole fraction） film, its structure was composed of Cu-ll%W solution, Cu-37%W solution and pure Cu; for Cu 14.3%W film, it was composed of Cu-15%W solution, Cu-38%W solution, and pure Cu; for Cu-18.1%W film, it was composed of Cu-19%W solution, Cu-36% W solution and pure Cu.展开更多
Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties an...Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties and microstructure and crystal structures of the resulting films were investigated by scanning electron microscopy（SEM）, atomic force microscopy（AFM）, X-ray diffraction（XRD）, spectrophotometer and Hall-effect measurement system, respectively. XRD results show that all AZO films exhibit a strong preferred c-axis orientation. However, the crystallinity of films decreases with the increase of substrate rotation speed, accompanying with the unbalanced grains grows. For the films prepared at different target-substrate distances, the uniform microstructure and morphology are observed. The highest carrier concentration of 5.9×1020 cm-3 and Hall mobility of 13.1 cm^2/（V·s） are obtained at substrate rotation speed of 0 and target-substrate distance of 7 cm. The results indicate that the structure and performances of the AZO films are strongly affected by substrate rotation speed.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant No.61235011)the Science Foundation of the Science and Technology Commission of Tianjin Municipality,China(Grant Nos.13JCYBJC17300 and 12JCQNIC01200)
文摘Diamond-like carbon （DLC） thin film is one of the most widely used optical thin films. The fraction of chemical bondings has a great influence on the properties of the DLC film. In this work, DLC thin films are prepared by ion-beam sputtering deposition in Ar and CH4 mixtures with graphite as the target. The influences of the ion-beam voltage on the surface morphology, chemical structure, mechanical and infrared optical properties of the DLC films are investigated by atomic force microscopy （AFM）, Raman spectroscopy, nanoindentation, and Fourier transform infrared （FTIR） spec- troscopy, respectively. The results show that the surface of the film is uniform and smooth. The film contains sp2 and sp3 hybridized carbon bondings. The film prepared by lower ion beam voltage has a higher sp3 bonding content. It is found that the hardness of DLC films increases with reducing ion-beam voltage, which can be attributed to an increase in the fraction of sp3 carbon bondings in the DLC film. The optical constants can be obtained by the whole infrared optical spectrum fitting with the transmittance spectrum. The refractive index increases with the decrease of the ion-beam voltage, while the extinction coefficient decreases.
基金financially supported by the Natural Science Foundation of China (62288102, 22379067, T2441002, 6220514, and 5230226)the National Key Research and Development Program of China (2023YFB4204500)+1 种基金the Jiangsu Provincial Departments of Science and Technology (BE2022023, BK20220010, and BZ2023060)the Open Project Program of Wuhan National Laboratory for Optoelectronics (2021WNLOKF003)。
文摘Perovskite solar cells(PSCs) have become a hot topic in the field of renewable energy due to their excellent power conversion efficiency and potential for low-cost manufacturing. The hole transport layer(HTL), as a key component of PSCs,plays a crucial role in the cell's overall performance. Magnetron sputtering NiO_(x) has attracted widespread attention due to its high carrier mobility, excellent stability, and suitability for large-scale production. Herein, an insightful summary of the recent progress of magnetron sputtering NiO_(x) as the HTL of PSCs is presented to promote its further development. This review summarized the basic properties of magnetron sputtering NiO_(x) thin film, the key parameters affecting the optoelectronic properties of NiO_(x) thin films during the magnetron-sputtering process, and the performance of the corresponding PSCs. Special attention was paid to the interfacial issues between NiO_(x) and perovskites, and the modification strategies were systematically summarized. Finally, the challenges of sputtering NiO_(x) technology and the possible development opportunities were concluded and discussed.
基金supported by National Natural Science Foundation of China (No.11275136)。
文摘The discharge and plasma characteristics of Ag magnetron sputtering discharge operated near the electron series resonance(ESR)oscillation,which was excited using the driving frequency of 27.12 MHz,was investigated.The imaginary part of impedance was found to undergo a transition from capacitive to inductive on varying radio-frequency(RF)power,and the conditions for the ESR excitation were satisfied.The current–voltage(I–V)characteristic of discharge showed that the lower discharge voltage with higher current was an important feature of RF magnetron sputtering operated near the ESR oscillation,which was caused by the small impedance Z originated from the mutual compensation between the sheath capacitive reactance and the plasma inductive reactance.The higher electron temperature,ion flux density and ion energy as well as the moderate electron density were obtained.The interaction of higher energy ions on substrate surface improved the crystallographic quality of Ag films.Therefore,the 27.12 MHz magnetron sputtering operated near the ESR oscillation has better deposition characteristics than that of commercial 13.56 MHz RF magnetron sputtering.
文摘Silver is an elegant white precious metal,but it is easily oxidized by O3,SO2,and H2S in the air,turning yellow or dark,which affects its decorative effect.The existing silver coating,primarily prepared through the electroplating process,poses serious environmental pollution problems.It is necessary to seek new,green,and environmentally friendly coating processes while also enhancing the color palette of silver jewelry coatings.Titanium film layers were deposited on Ag925 and Ag999 surfaces using magnetron sputtering coating technology.The effects of sputtering time,substrate surface state,reaction gas type and time,and film thickness on the color of the film layers were studied,and the anti discoloration performance of the obtained film layers under the optimal process was tested.The experimental results show that when the sputtering time varies from 5 to 10 minutes,injecting argon,oxygen,and nitrogen into the coating chamber yields rich colors such as purple with a red tint,blue,yellow green,yellowish purple,and blue purple.The precise control of gas injection time has a significant impact on the color of the film layer.In terms of anti tarnish performance,the film showed good stability in the artificial sweat immersion test.From an environmental perspective,the magnetron sputtering titanium film process has no harmful gas or liquid emissions,which aligns with the sustainable development trend of the jewelry industry and holds great promise for application.This study has improved the visual effect and practical performance of the product,providing important theoretical basis and experimental data support for the application of environmentally friendly silver surface vacuum magnetron sputtering titanium thin film coating technology.
基金funded by Open Research Fund Program of National Key Laboratory of Aerospace Chemical Power(NKLACP120241B04)National Natural Science Foundation of China Youth Science Foundation(12402450)。
文摘Ammonium dinitramide(ADN),as a high-energy oxidizer widely applied in the field of rocket and missile propellants,has a prominent issue of high hygroscopicity due to its strong polarity.The previous coating encapsulation methods have struggled to address the problems of uneven coating and polarity mismatch.This research innovatively introduces perfluorooctanoic acid(PFOA)as a polar transition intermediate layer.Utilizing the polarity of one end of it to adsorb on the surface of ADN through hydrogen bonds,the problem of polarity mismatch is effectively overcome.Meanwhile,the vibrational magnetron sputtering process has been first applied in the energetic field,with a special vibrating abutment enhancing ADN particle fluidity to solve coating non-uniformity,thus preparing prilled ADN@PFOA@PTFE core-dual-shell composites.Performance tests reveal that this composite material possesses excellent hydrophobic and anti-hygroscopic properties.When left at 25℃and 75%RH for 3 days,moisture absorption was reduced by more than 90%compared to pure ADN.Simultaneously,its thermal stability,heat release performance,and combustion performance have been improved.The research achievements optimize the storage conditions of ADN in the application of rocket and missile propellants,providing solid support and broad development prospects for technological innovation in military fields.
文摘Ensuring high electrocatalytic performance simultaneously with low or even no precious-metal usage is still a big challenge for the development of electrocatalysts toward oxygen evolution reaction(OER)in anion exchange membrane water electrolysis.Here,homogeneous high entropy oxide(HEO)film is in-situ fabricated on nickel foam(NF)substrate via magnetron sputtering technology without annealing process in air,which is composed of many spinel-structured(FeCoNiCrMo)_(3)O_(4) grains with an average particle size of 2.5 nm.The resulting HEO film(abbreviated as(FeCoNiCr-Mo)_(3)O_(4))exhibits a superior OER performance with a low OER overpotential of 216 mV at 10 mA cm^(–2) and steadily operates at 100 mA cm^(–2) for 200 h with a decay of only 272μV h^(–1),which is far better than that of commercial IrO_(2) catalyst(290 mV,1090μV h^(–1)).Tetramethylammonium cation(TMA^(+))probe experiment,activation energy analysis and theoretical calculations unveil that the OER on(FeCoNiCrMo)_(3)O_(4) follows an adsorbate evolution mechanism pathway,where the energy barrier of rate-determining step for OER on(FeCoNiCrMo)_(3)O_(4) is substantially lowered.Also,methanol molecular probe experiment suggests that a weakened ^(*)OH bonding on the(FeCoNiCrMo)_(3)O_(4) surface and a rapid deprotonation of ^(*)OH,further enhancing its OER performance.This work provides a feasible solution for designing efficient high entropy oxides electrocatalysts for OER,accelerating the practical process of water electrolysis for H2 production.
基金co-supported by the National Key R&D Program of China(No.2022YFB3403500)the National Natural Science Foundation of China(No.NSFC52202460)the China Postdoctoral Science Foundation(Nos.2021M690392,2021TQ0036,and 2023TQ0031)。
文摘In the past few decades,ion engines have been widely used in deep-space propulsion and satellite station-keeping.The aim of extending the thruster lifetime is still one of the most important parts during the design stage of ion engine.As one of the core components of ion engine,the grid assembly of ion optic systems may experience long-term ion sputtering in extreme electro-thermal environments,which will eventually lead to its structural and electron-backstreaming failures.In this paper,the current studies of the grid assembly erosion process are systematically analyzed from the aspects of sputtering damage process of grid materials,numerical simulations,and measurements of erosion characteristics of grid assembly.The advantages and disadvantages of various erosion prediction models are highlighted,and the key factors and processes affecting the prediction accuracy of grid assembly erosion patterns are analyzed.Three different types of experimental methods of grid assembly erosion patterns are compared.The analysis in this paper is of great importance for selecting the sputter-resistant grid materials,as well as establishing the erosion models and measurement methods to accurately determine the erosion rate and failure modes of grid assembly.Consequently,the working conditions and structure parameters of ion optic systems could be optimized based on erosion models to promote the ion engine lifetime.
基金Project supported by the Key-Area Research and Development Program of Guangdong Province,China(Grant No.2021B0101260001)the Guangdong Basic and Applied Basic Research Foundation(Grant No.2019A1515110411)。
文摘Ta-doped SnO_(2)(TTO)is a suitable candidate to replace transparent conductive oxide(TCO)composed of expensive indium used for optoelectronics and silicon heterojunction solar cells fabricated below 200℃.However,TTO films fabricated by sputtering at low temperature still demonstrate too high resistance and optical absorptance for application in industry.In this study,we investigate the influence of sputtering ambient on the optoelectrical properties of TTO films.The addition of hydrogen and oxygen to argon during sputtering leads to a large improvement in the optoelectrical properties of TTO films.The best TTO film has a low average absorptance of 1.9%and a low resistance of 3.8×10^(-3)Ω·cm with a high carrier density of 9.3×10^(19)cm^(-3)and mobility of 17.8 cm^(2)·V^(-1)·s^(-1).The micros tructural and compositional properties of TTO films were characterized using x-ray diffraction,x-ray photoelectron spectroscopy and UV-Vis spectrophotometry.A proper ratio of hydrogen to oxygen in the sputtering gas improves the crystallinity and the doping efficiency of Ta.Optical absorptance is also reduced with suppressed formation of Sn(Ⅱ)in the TTO films.Therefore,our findings exhibit remarkable potential for the industrial application of TTO as a low-cost TCO.
基金supported by the National Natural Science Foundation of China (Grant Nos. 42188101, 42274211, 41974170, 42374184, 42122032, and 41974196)the Chinese Academy of Sciences (Grant Nos. QYZDJSSW-JSC028, XDA15052500, XDA17010301, and XDB41000000)+3 种基金the CNSA (Grant No. D050103)the Specialized Research Fund for State Key Laboratories of Chinathe Specialized Research Fund for Laboratory of Geospace Environment of the University of Science and Technology of Chinasupported by the International Space Science Institute (ISSI) in Bern and Beijing through the ISSI/ISSI-BJ International Team Project titled “Understanding the Mars Space Environment Through Multi-Spacecraft Measurements” (ISSI Team Project No. 23-582 and ISSI-BJ Team Project No. 58)
文摘Atmospheric escape plays a critical role in shaping the long-term climate evolution of Mars.Among the various escape mechanisms,energetic neutral atoms(ENAs)generated through charge exchange between solar wind ions and exospheric neutrals serve as an important diagnostic for ion-neutral interactions and upper atmospheric loss.This study presents direct observations of hydrogen ENAs(H-ENAs)on the dayside of Mars by using the Mars Ion and Neutral Particle Analyzer(MINPA)onboard China’s Tianwen-1 orbiter.By analyzing H-ENA data during a coronal mass ejection and a stream interaction region from December 29,2021,to January 1,2022,and comparing these data with MAVEN/SWIA(Mars Atmosphere and Volatile EvolutioN/Solar Wind Ion Analyzer)solar wind measurements,we examine the temporal evolution of H-ENA flux and the associated sputtered escape of atmospheric constituents.The observed H-ENA velocity is consistent with upstream solar wind ions,and the H-ENA-to-ion intensity ratio is used to infer variations in exospheric density,revealing a delayed response to enhanced solar wind activity.Penetrating H-ENA intensities reach up to 5.3×10^(6)s^(−1) cm^(−2),with energy fluxes on the order of(0.5-8.1)×10^(−3) mW/m^(2).The estimated oxygen sputtered escape rate driven by penetrating H-ENAs ranges from 5.5×10^(23)s^(−1) to 5.2×10^(24)s^(−1),comparable to or exceeding previous estimates based on penetrating ions.The findings highlight the need for low-altitude H-ENA observations to better quantify their atmospheric interactions and refine our understanding of nonthermal escape processes at Mars.
基金financially supported by the National MCF Energy R&D Program(Grant No.2022YFE03190100)the National Natural Science Foundation of China(Grant Nos.12422513,12105035,U21A20438)the Xiaomi Young Talents Program。
文摘One of the primary concerns associated with ion cyclotron resonance heating(ICRH)is the enhanced impurity sputtering resulting from radio frequency(RF)sheath formation near plasma-facing components(PFCs),such as limiters.Developing a sputtering model integrated with RF sheath simulations allows for a more comprehensive understanding of the kinetic behavior of incident ions and their interactions with the limiter surface.We accordingly develop an impurity sputtering model“PMSAD”,which computes the sputtering yield(amount of impurity)on the limiter surface based on incident ion characteristics and predicts the spatial distribution of impurities.The model provides a robust method for understanding and analyzing the impurity sputtering process from limiter surfaces,which is crucial for preventing ICRH surface erosion and reducing edge and core plasma contamination.
文摘One-dimensional ZnO nanorods are synthesized by ox idating thin metal zinc films deposited on Si(111) substrates with radio frequen cy magnetron sputtering.The crystal structure,surface morphology,and optical pro perties of nanorods are investigated.X-ray diffraction(XRD) pattern,scanning el ectron microscopy(SEM),and transmission electron microscopy(TEM) analyses show t hat the synthesized single-crystal ZnO nanorods develop like hairpins along dif ferent radials,with a hexagonal wurtzite structure.The diameters of nanorods ran ge between 30 and 60nm and lengths up to micrometers.Photoluminescence(PL) analy sis shows that,under 280nm light excitation,a strong and sharp near band-edge U V light emission band at 372nm and a relatively weak green deep-level light emi ssion band at 516nm are observed from the ZnO nanorods,which indicates excellent crystallization and optical quality of the fabricated ZnO nanorods.
基金supported by open research fund from Guangxi Key Laboratory of New Energy and Building Energy Saving, China
文摘Al-doped ZnO thin films were prepared on glass substrate using an ultra-high density target by RF magnetron sputtering at room temperature. The microstructure, surface morphology, optical and electrical properties of AZO thin films were investigated by X-ray diffractometer, scanning electron microscope, UV-visible spectrophotometer, four-point probe method, and Hall-effect measurement system. The results showed that all the films obtained were polycrystalline with a hexagonal structure and average optical transmittance of AZO thin films was over 85 % at different sputtering powers. The sputtering power had a great effect on optoelectronic properties of the AZO thin films, especially on the resistivity. The lowest resistivity of 4.5×10^-4 Ω·cm combined with the transmittance of 87.1% was obtained at sputtering power of 200 W. The optical band gap varied between 3.48 and 3.68 eV.
文摘In order to study the effect of the microstructure with Al and V added TiN coatings, TiN, TiAlN and TiAlVN coatings were deposited on AISI M2 high-speed steels by magnetron reactive sputtering. The microstructures of all the coatings were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results indicate that the addition of Al into TiN coatings reduces their lattice constant, but a further addition of V into TiAlN coatings increases their lattice constant. Moreover, the growth morphologies for TiN, TiAlN, and TiAlVN indicate that adding Al and V has a tendency to improve the columnar structure. The (111) and (200) orientations of TiN, TiAlN, and TiAlVN are identified. Theε(Fe3N-Fe2N) phase occurs because a small amount of Fe is present in the coatings. The interlayers of TiAlN and TiAlVN have the preferred (01 1 0) orientation. The texture (columnar) structure of the (111) and (200) orientations is observed in the TiAlN and TiAlVN coatings. An orientation relationship of (01 1 0)α-Ti//(110)T.M occurs between the interlayer and tempered martensite (T.M) in TiAlVN.
基金Project(21271188)supported by the National Natural Science Foundation of ChinaProject(2012M521541)supported by the China Postdoctoral Science Foundation+2 种基金Project(2012QNZT002)supported by the Fundamental Research Funds for the Central South Universities,ChinaProject(20110933K)supported by the State Key Laboratory of Powder Metallurgy,ChinaProject(CSU2012024)supported by the Open-End Fund for Valuable and Precision Instruments of Central South University,China
文摘Wurtzite aluminum nitride（AlN） films were deposited on Si（100） wafers under various sputtering pressures by radio-frequency（RF） reactive magnetron sputtering. The film properties were investigated by XRD, SEM, AFM, XPS and nanoindenter techniques. It is suggested from the XRD patterns that highly c-axis oriented films grow preferentially at low pressures and the growth of（100） planes are preferred at higher pressures. The SEM and AFM images both reveal that the deposition rate and the surface roughness decrease while the average grain size increases with increasing the sputtering pressure. XPS results show that lowering the sputtering pressure is a useful way to minimize the incorporation of oxygen atoms into the AlN films and hence a film with closer stoichiometric composition is obtained. From the measurement of nanomechanical properties of AlN thin films, the largest hardness and elastic modulus are obtained at 0.30 Pa.
基金Project(50725413)supported by the National Natural Science Foundation of ChinaProject(2010BB4290)supported by Natural Science Foundation Project of CQ CSTC,China
文摘Nano-scaled ZrNbAlN films with different negative bias voltages（Vb） were deposited on bronze substrate and Si（100） wafers by a reactive unbalanced magnetron sputtering technique. Composition and structure properties were characterized by X-ray photoelectron spectroscopy and X-ray diffraction. It is found that mole concentrations of Zr and Nb are affected by Vb, which leads to the increase of binding energy of N 1s and Al 2p and decrease of binding energy of Zr 3d5/2 and Nb 3d5/2. Surface morphologies evolution controlled by Vb could be observed. Furthermore, X-ray diffraction patterns reveal that these films show a（111） preferred orientation. Moreover, mechanical property and corrosion behavior of ZrNbAlN films were characterized by nanoindentation test and corrosion test, respectively. A maximum value of 21.85 GPa at-70 V occurs in the ZrNbAlN- bronze system, which outperforms uncoated bronze. Corrosion experiments in 0.5 mol/L NaCl and 0.5 mol/L HCl solution show that corrosion potential and corrosion current are dependent on Vb, and better anti-corrosion property could be obtained at-90 V.
文摘A kind of W/DLC/W-S-C composite film was fabricated by magnetron sputtering method.Effects of WSx content on the structure and the adhesion of the composite films were investigated.In addition,tribological behavior of the composite films was studied in the conditions of the ambient air and N2 gas atmosphere by ball-on-disk tester.The results indicate that the composite films show dense and amorphous microstructure.The WCx and WSx compounds are found in amorphous diamond like carbon matrix in the top layers of W-S-C.A proper WSx content is beneficial for improving the adhesion of the composite films.In air atmosphere,the composite films with high C content have better wear resistance and the friction coefficients range from 0.15 to 0.25.In N2 condition,high WSx content is benefit for the wear resistance and the friction coefficients of the composite films range from 0.03 to 0.1.
文摘Zinc nitride （Zn3N2） thin films were prepared by radio frequency （RF） magnetron sputtering on quartz glass at different substrate temperatures.The structure and composition were characterized by X-ray diffraction and Raman-scattering measurements,respectively.The polycrystalline phase Zn3N2 films appeared when the ratio of the N2 partial pressure to the total pressure reached 1/2.The effects of the substrate temperature on the electrical and optical properties of the Zn3N2 films were investigated by Hall measurements and optical transmission spectra.The electrical and optical properties of the films were highly dependent on the substrate temperature.With the substrate temperature increasing from 100 to 300℃,the resistivity of the Zn3N2 films decreased from 0.49 to 0.023Ω·cm,the carrier concentration increased from 2.7×10^16 to 8.2×10^19cm^-3,and the electron mobility decreased from 115 to 32cm^2/（V·s）.The deposited Zn3N2 films were considered to be n-type semiconductors with a direct optical band gap,which was around 1.23eV when the substrate temperature was 200℃.
文摘Microstructure of GaAs/SiO 2 nanogranular thin films fabricated by radio frequency magnetron co sputtering technique and postannealing are investigated via atomic force microscope,X ray diffraction,and Rutherford backscattering spectroscopy.The results show that GaAs nanocrystals with average diameters from 1 5nm to 3 2nm (depending on the annealing temperature) are uniformly dispersed in the SiO 2 matrices.GaAs and SiO 2 are found in normal stoichiometry in the films.The nonlinear optical refraction and nonlinear optical absorption are studied by Z scan technique using a single Gaussian beam of pulse laser.The third order nonlinear optical refractive index and nonlinear absorption coefficient are enhanced due to the quantum confinement effects and estimated to be 4×10 -12 m 2/W and 2×10 -5 m/W respectively in nonresonant condition,while 2×10 -11 m 2/W and -1×10 -4 m/W respectively in quasi resonant condition.
文摘Immiscible Cu-W alloy thin films were prepared using dual-target magnetron sputtering deposition process. The structure evolution of Cu-W thin films during preparation was investigated by X-ray diffraction, transmission electron microscopy and high resolution transmission electron microscopy. In the initial stage of dual-target magnetron sputtering deposition process, an amorphous phase formed; then it crystallized and the analogy spinodal structure formed due to the bombardment of the sputtered particles during sputtering deposition process, the surface structure of the film without the bombardment of the sputtered particles was the amorphous one, the distribution of the crystalline and amorphous phase showed layer structure. The solid solubility with the analogy spinodal structure was calculated using the Vegard law. For Cu-13.7%W （mole fraction） film, its structure was composed of Cu-ll%W solution, Cu-37%W solution and pure Cu; for Cu 14.3%W film, it was composed of Cu-15%W solution, Cu-38%W solution, and pure Cu; for Cu-18.1%W film, it was composed of Cu-19%W solution, Cu-36% W solution and pure Cu.
基金Project(51302044)supported by the National Natural Science Foundation of ChinaProject(2012M521596)supported by the Chinese Postdoctoral Science FoundationProject(KLB11003)supported by the Key Laboratory of Clean Energy Materials of Guangdong Higher Education Institute,China
文摘Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties and microstructure and crystal structures of the resulting films were investigated by scanning electron microscopy（SEM）, atomic force microscopy（AFM）, X-ray diffraction（XRD）, spectrophotometer and Hall-effect measurement system, respectively. XRD results show that all AZO films exhibit a strong preferred c-axis orientation. However, the crystallinity of films decreases with the increase of substrate rotation speed, accompanying with the unbalanced grains grows. For the films prepared at different target-substrate distances, the uniform microstructure and morphology are observed. The highest carrier concentration of 5.9×1020 cm-3 and Hall mobility of 13.1 cm^2/（V·s） are obtained at substrate rotation speed of 0 and target-substrate distance of 7 cm. The results indicate that the structure and performances of the AZO films are strongly affected by substrate rotation speed.
