期刊文献+

基于高阶累积量的齿轮系统辨识方法研究 被引量:4

A Gear System Identification Method Based on Higher Order Cumulants
在线阅读 下载PDF
导出
摘要 高阶累积量分析技术是近年来迅速发展起来的新技术 ,作为处理非高斯信号、非线性信号以及盲信号的重要工具而受到日益重视。它有许多优点 ,特别是对于外加高斯噪声不敏感以及可以检测系统的非线性特性 ,故理论上可以完全抑制高斯噪声的影响 ,提高分析精度。本文在对其研究的基础上 ,将它应用于齿轮旋翼传动系统动态特性分析之中 ,对传动系统和旋翼桨叶的动态固有频率等进行了识别 ,并与频域和时域识别法进行了比较 ,表明该方法是一种可行的有发展前途的方法 。 A gear transmission system exhibits a coupling nonlinear vibration due to the nonlinearity of gear meshing,bearing and gearbox supporting system stiffnesses incorporated with the modulating of gear and bearing as well as the nonlinear coupling of rotary wings.The dynamic signals of the system appear of complicated non-Gauss and nonlinear characteristics.A new method of modern signal processing-the higher order cumulant was adopted.The nonlinear modulating characteristics of the system were monitored by determining the dynamic response of the transmission system and helicopter rotary wings.The dynamic natural frequencies of the transmission system and the rotary wings were obtained by analyzing in the cumulant domain.Its comparison with the power spectrum method and the time-series analysis (ARMA) identification Method shows that the higher order cumulant method is supperior in noise inhibiting,higher identification accuracy and nonlinear characteristic extracting of the system.
出处 《航空动力学报》 EI CAS CSCD 北大核心 2000年第4期435-438,共4页 Journal of Aerospace Power
基金 航空科学基金资助项目! (94C5 30 92 )
关键词 齿轮传动系统 旋翼 高阶累积量 辨识 gear transmission system rotor wings dyanmic properties higher order cumulant identificatioD
  • 相关文献

参考文献3

二级参考文献11

  • 1邵忍平,何大为,沈允文,徐敏.齿轮减速器扭振特性实验辨识及简化动力模型研究[J].机械传动,1996,20(3):20-23. 被引量:2
  • 2邵忍平,沈允文,刘更,徐敏.齿轮旋翼传动系统动态固有特性识别[J].航空动力学报,1997,12(2):206-208. 被引量:6
  • 3方宗德 机械传动学会齿轮专业委员会.斜轮传动态特性的理论与实验研究.第二届全国齿轮动力学学术会议论文集[M].武昌:齿轮专业委员会,1991.52-59.
  • 4邵忍平.齿轮传动系统振动特性辨识及声辐射机理研究[M].西安:西北工业大学,1999..
  • 5邵忍平,机械科学与技术,1996年,15卷,1期
  • 6团体著者,直升机动力学手册,1990年
  • 7周传荣,机械振动参数识别及其应用,1989年
  • 8邵忍平,学位论文,1999年
  • 9Sho H,Bulletin of JSME,1995年,38卷,1期,112页
  • 10方宗德,第二届全国齿轮动力学学术会议论文集,1991年,52页

共引文献14

同被引文献42

  • 1吴淼 周雅立 等.齿根裂纹诊断技术.全国第二届齿轮动力学学术会议论文[M].武昌,1991.192-198.
  • 2郑吉兵.裂纹转子的动态响应、稳定性及分叉与混沌:[博士学位论文].西安:西北工业大学,1996..
  • 3廖明夫.裂纹转子动力学特性及其监测技术研究:[博士学位论文].西安:西北工业大学,1996..
  • 4周海 加藤正名 等.齿车装置状态诊断.日本机械学会论文集[M].,1994,60(571).1064-1069.
  • 5Lin Darning, Murray Wiseman, Dragan Banjevic, et al. An Approach to Signal Processing and Condition-Based Maintenance for Gearboxes Subject to Tooth Failure. Mechanical Systems and Signal Processing, 2004, 18(5):993-1007
  • 6Chinmaya Kar, Mohant A R. Multistage Gearbox Condition Monitoring Using Motor Current Signature Analysis and Kolmogorov-Smirnov Test. Journal of Sound and Vibration, 2006, 290(1-2): 337-368
  • 7Vania A, Pennacchi P. Experimental and Theoretical Application of Fault Identification Measures of Accuracy in Rotating Machine Diagnostics. Mechanical Systems and Signal Processing, 2004,18(6): 329-352
  • 8Dalpiaz G, Rivola A, Rubini R. Effectiveness and Sensitivity of Vibration Processing Techniques for Local Fault Detection in Gears. Mechanical Systems and Signal Processing, 2000,14 (3) : 387-412
  • 9Lai Wuxing, Peter W T, Zhang Guicai, Shi Tielin. Classification of Gear Faults Using Cumulants and the Radial Basis Function Network. Mechanical Systems and Signal Processing, 2004, 18(2), 381-389
  • 10LIN D, WISEMAN M, BANJEVIC D, et al. An approach to signal processing and condition-based maintenance for gearboxes subject to tooth failure[J]. Mechanical Systems and Signal Processing, 2004, 18(5): 993-1 007.

引证文献4

二级引证文献44

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部