According to the structure character of the passive sub-chain of the 3TPS-TPparallel mechanism, the kinematic constraint equations of the movable platform are established,based on which the closed-form inverse kinemat...According to the structure character of the passive sub-chain of the 3TPS-TPparallel mechanism, the kinematic constraint equations of the movable platform are established,based on which the closed-form inverse kinematics formula of the parallel mechanism are presented.Through parting the spherical joints of the active sub-chains and using the force and momentequilibrium of both the active sub-chains and passive sub-chain, the constraint forces acting on theparted joints are determined. Subsequently, the analytic expressions of the actuator driving forcesare derived by means of the force equilibrium of the upper links of active sub-chains.展开更多
In order to improve nitrogen removal in anoxic/oxic(A/O) process effectively for treating domestic wastewaters, the influence factors, DO(dissolved oxygen), nitrate recirculation, sludge recycle, SRT(solids residence ...In order to improve nitrogen removal in anoxic/oxic(A/O) process effectively for treating domestic wastewaters, the influence factors, DO(dissolved oxygen), nitrate recirculation, sludge recycle, SRT(solids residence time), influent COD/TN and HRT(hydraulic retention time) were studied. Results indicated that it was possible to increase nitrogen removal by using corresponding control strategies, such as, adjusting the DO set point according to effluent ammonia concentration; manipulating nitrate recirculation flow according to nitrate concentration at the end of anoxic zone. Based on the experiments results, a knowledge-based approach for supervision of the nitrogen removal problems was considered, and decision trees for diagnosing nitrification and denitrification problems were built and successfully applied to A/O process.展开更多
Effect of added carbon source and nitrate concentration on the denitrifying phosphorus removal by DPB sludge was systematically studied using batch experiments, at the same time the variation of ORP was investigated. ...Effect of added carbon source and nitrate concentration on the denitrifying phosphorus removal by DPB sludge was systematically studied using batch experiments, at the same time the variation of ORP was investigated. Results showed that the denitrifying and phosphorus uptake rate in anoxic phase increased with the high initial anaerobic carbon source addition. However once the initial COD concentration reached a certain level, which was in excess to the PHB saturation of poly-P bacteria, residual COD carried over to anoxic phase inhibited the subsequent denitrifying phosphorus uptake. Simultaneously, phosphate uptake continued until all nitrate was removed, following a slow endogenous release of phosphate. High nitrate concentration in anoxic phase increased the initial denitrifying phosphorus rate. Once the nitrate was exhausted, phosphate uptake changed to release. Moreover, the time of this turning point occurred later with the higher nitrate addition. On the other hand, through on-line monitoring the variation of the ORP with different initial COD concentration, it was found ORP could be used as a control parameter for phosphorus release, but it is impossible to utilize ORP for controlling the denitrificaion and anoxic phosphorus uptake operations.展开更多
The piezoelectric pump with nozzle/diffuser-elements, which oscillating formdiffering from regular volumetric reciprocating or rotating pumps because there arenozzle/diffuser-elements substituted for regular valves, i...The piezoelectric pump with nozzle/diffuser-elements, which oscillating formdiffering from regular volumetric reciprocating or rotating pumps because there arenozzle/diffuser-elements substituted for regular valves, is a new type pump whose actuator is apiezoelectric ceramal part with verse piezoelectric effect In recent year, piezoelectric pump ispaid increasing attention to because it is an ideal candidate in application in such area as medicalhealth, mechanical tools and micro-mechanism. The fundamental research on it, however, is still notmade through. Focuses on the phenomenon of different directions of flow among Germany pump, Chinesepump and Swiss pump, which are all fitted with nozzle/diffuser-elements, and analyzes the coneangle of nozzle/diffuser-elements based on the flow equation of valve-less piezoelectric pump withnozzle/diffuser-elements. As a result, the concepts of diffuser toss coefficient and losscoefficient are introduced to explain these phenomena, from which a discussion is given on theoptimization of the cone angle of nozzle/diffuser-element aiming at the maximum of pump flow.展开更多
On the basis of continuous tests and batch tests, conversion regular patterns of acetate, propionate and butyrate in activated sludge at different heights of the UASB reactor were conducted. Results indicated that the...On the basis of continuous tests and batch tests, conversion regular patterns of acetate, propionate and butyrate in activated sludge at different heights of the UASB reactor were conducted. Results indicated that the conversion capacity of the microbe is decided by the substrate characteristic when sole VFA is used as the only substrate. But when mixed substrates are used,the conversion regulations would have changed accordingly. Relationships of different substrates vary according to their locations. In the whole reactor, propionate's conversion is restrained by acetate and butyrate of high concentration. On the top and at the bottom of the reactor, conversion of acetate, but butyrate, is restrained by propionate. And in the midst, acetate's conversion is accelerated by propionate while that of butyrate is restrained. It is proved, based on the analysis of specific conversion rate, that the space distribution of the microbe is the main factor that affects substrates' conversion. The ethanol type fermentation of the acidogenic phase is the optimal acid type fermentation for the two phase anaerobic process.展开更多
A coating with high hardness, wear and oxidation resistance was prepared by electric arc spray. The hardness, bonding strength, abrasive wear and values of porosity and oxidation resistance of the coating were investi...A coating with high hardness, wear and oxidation resistance was prepared by electric arc spray. The hardness, bonding strength, abrasive wear and values of porosity and oxidation resistance of the coating were investigated. The microstructures and function of Cr3C2 of the coating were analyzed. The results showed surface Rockness Hardness HR30 reached 72.5 and average bond strength reached 49.1Mpa. Also porosity value was less than 2%. In addition, it was found from the comparison between the coating and 45CT coating that, oxidation resistance of the coating was less than that of 45CT, but the abrasive wear of the coating was obvious better than that of 45CT.展开更多
The contributing factors for the cavitation in piezoelectric pumps areanalyzed, theoretically, and the device fitting for observing and recording is set up. With it theexperiments are carried out to observe the emerge...The contributing factors for the cavitation in piezoelectric pumps areanalyzed, theoretically, and the device fitting for observing and recording is set up. With it theexperiments are carried out to observe the emergence and the flowing of the cavitations in thepiezoelectric pumps. According to the statistic and the analysis to the data of the experiments, thepeculiar features are discovered. These features are composed of balls-amassing, center-more, andflow-out.展开更多
Natural daylight has more and more been used in modem buildings to save building energy consumption in China. Light pipe is one of the effective way to reduce electricity consumption for lighting, it can transmit ligh...Natural daylight has more and more been used in modem buildings to save building energy consumption in China. Light pipe is one of the effective way to reduce electricity consumption for lighting, it can transmit light from outdoor to the room without generating excessive heat. Experimental apparatus of side lighting light pipe is described in this paper. Light pipe for side daylighting purpose was installed in the Key Laboratory of Enhanced Heat Transfer and Energy Conservation, Ministry of Education, Beijing University of Technology. It was 2.6m long, with diameters of 360mm.The performance of the light pipe for whole day had been measured. The highest iUuminance was 488lux on Dec.26,2002, obtained from the point beneath the center of the diffuser of the light pipe 1450mm. The ratio of internal illuminance to external was 0.23 %. Because it has many advantages to improve energy efficiency in buildings, light pipe will be populanzed in the near future in China.展开更多
The microstructure, mechanical properties, and electron-emission propertiesof a newly developed heated cathode material Mo-CeO_2 with 4.0% (mass fraction) of CeO_2 wereinvestigated. It is shown that the Mo-CeO_2 catho...The microstructure, mechanical properties, and electron-emission propertiesof a newly developed heated cathode material Mo-CeO_2 with 4.0% (mass fraction) of CeO_2 wereinvestigated. It is shown that the Mo-CeO_2 cathode material possesses high tensile strength andgood room-temperature ductility. After carbonized, the Mo-CeO_2 cathode material has a higher zerofield emission current density and a lower work function compared with the W-ThO_2 cathode material.展开更多
The compound bioceramic coating containing calcium (Ca) and phosphorus (P) on titanium alloy substrate was prepared by means of micro-arc oxidation (MAO) treatment. The results show that under the different electrolyt...The compound bioceramic coating containing calcium (Ca) and phosphorus (P) on titanium alloy substrate was prepared by means of micro-arc oxidation (MAO) treatment. The results show that under the different electrolyte the coating with the color of gray or black and surface morphology of cauliflower or honeycomb, where Ca content and P contain can attain 30% and 20% respectively, can be obtained. Meanwhile, the influences of electrolyte temperature, current density and discharge time on morphology and thickness of coating are also discussed here.展开更多
AIM: To study morphologic and biomechanical changes of oesophagus in diabetes rats.METHODS: Diabetes was induced by a single injection of streptozotocin (STZ). The type of diabetes mellitus induced by parenteral STZ a...AIM: To study morphologic and biomechanical changes of oesophagus in diabetes rats.METHODS: Diabetes was induced by a single injection of streptozotocin (STZ). The type of diabetes mellitus induced by parenteral STZ administration in rats was insulin-dependent (type I). The samples were excised and studied in vitro using a self-developed biomaterial test machine.RESULTS: The body mass was decreased after 4 d with STZ treatment. The length of esophagus shortened after 4, 7,14 d. The opening angle increased after 14 d. The shear,longitudinal and circumferential stiffness were obviously raised after 28 d of STZ treatment.CONCLUSION: The changes of passive biomechanical properties reflect intra-structural alteration of tissue to a certain extent. This alteration will lead to some dysfunction of movement. For example, tension of esophageal wall will change due to some obstructive disease.展开更多
The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow r...The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow rate of external carbon dosage to the anoxic zone, thus the concentration of nitrate plus nitrite(NOx--N) in the anoxic zone was kept closed to the set point. The relationship was studied between the NOx--N concentration in the anoxic zone(S_ NO) and the dosage of external carbon, and the results showed that the removal efficiency of the total nitrogen(TN) could not be largely improved by double dosage of carbon source when S_ NO reached about 2 mg/L. Through keeping S_ NO at the level of about 2 mg/L, the demand of effluent quality could be met and the carbon dosage could be optimized. Based on the Activated Sludge Model No.1(ASM No.1), a simplified mathematical model of external carbon dosage was developed. Simulation results showed that PI controller and feed-forward PI controller both had good dynamic response and steady precision. And feed-forward PI controller had better control effects due to its consideration of influent disturbances.展开更多
Measuring amplitude of signal is the usual method in wavelength demodulation of fiber Bragg grating (FBG) sensors recently. This method is easy to be disturbed and has low precision. In this paper, a novel counting wa...Measuring amplitude of signal is the usual method in wavelength demodulation of fiber Bragg grating (FBG) sensors recently. This method is easy to be disturbed and has low precision. In this paper, a novel counting wavelength demodula- tion scheme of FBG sensors using a high birefringent fiber (HBF) loop mirror is reported. This demodulator has simple structure, high precision, cheap price and convenient use. The resolution of the loop mirror device with a HBF of 30 meters long is 0.067 nm. For a center wavelength of FBG of about 1550 nm and a 40 nm shift range of its reflection wavelength, the relative error of measurement is only ± 0.001. This wavelength demodulation device has significance for widespread application of FBG sensors.展开更多
The paper describes a texture-based fast text location scheme which operates directly in the Discrete Wavelet Transform (DWT) domain. By the distinguishing texture characteristics encoded in wavelet transform domain, ...The paper describes a texture-based fast text location scheme which operates directly in the Discrete Wavelet Transform (DWT) domain. By the distinguishing texture characteristics encoded in wavelet transform domain, the text is fast detected from complex background images stored in the compressed format such as JPEG2000 without full decompress. Compared with some traditional character location methods, the proposed scheme has the advantages of low computational cost, robust to size and font of characters and high accuracy. Preliminary experimental results show that the proposed scheme is efficient and effective.展开更多
AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angle...AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angles of collagen fiber and the pressure it undergoes.METHODS: A kind of 2-dimensional visible quantitative analyzing technique was described. Digital image-processing method was utilized to determine the angle of collagen fiber in parenchyma according to the changes of area analyzed and further to investigate quantitatively the distribution of collagen fiber. A series of intestinal slice′s images preprocessed by polarized light were obtained with electron microscope,and they were processed to unify each pixel. The approximate angles between collagen fibers were obtained via analyzing the images and their corresponding polarized light. The relationship between the angles of collagen fiber and the pressure it undergoes were statistically summarized.RESULTS: The angle of collagen fiber in intestinal tissue was obtained with the quantitative analyzing method of calculating the ratio of different pixels. For the same slice,with polarized light angle′s variation, the corresponding ratio of different pixels was also changed; for slices under different pressures, the biggest ratio of collagen fiber area was changed either.CONCLUSION: This study suggests that the application of stress on the intestinal tissue will change the angle and content of collagen fiber. The method of calculating ratios of different pixel values to estimate collagen fiber angle was practical and reliable. The quantitative analysis used in the present study allows a larger area of soft tissue to be analyzed with relatively low cost and simple equipment.展开更多
Low-cycle fatigue experiments of tension-compression, torsion andtension-torsion with holding time were performed. The interaction law of creep and fatigue undermultiaxial stress at high temperature was investigated, ...Low-cycle fatigue experiments of tension-compression, torsion andtension-torsion with holding time were performed. The interaction law of creep and fatigue undermultiaxial stress at high temperature was investigated, and the micro-mechanism of equilibriumdiagrams was analyzed. A united equation of fatigue life under multiaxial stress was proposed.展开更多
A high-speed photographic method is mainly used to analyze metal transfer ofa cellulose covered electrode in the vertical down welding. The experimental results show that finedroplets spraying transfer and globular tr...A high-speed photographic method is mainly used to analyze metal transfer ofa cellulose covered electrode in the vertical down welding. The experimental results show that finedroplets spraying transfer and globular transfer are the dominant transfer characteristic. The largedroplet spatter, especially the upwards spatter, is a particular phenomenon. It is found that thecombination action of gas blow force, surface tension, gravitational force and electromagnetic forcelead to globular transfer. Gravitational force and electromagnetic force, which hasten big dropletspatter, should not be neglected.展开更多
The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power...The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power device of the static leg becomes azero-current-switch (ZCS), power device of the shifted leg becomes a zero-voltage-switch(ZVS). Thus,on one hand IGBT (Insulated gate bipolar transistor) with tail current can be easily used infull-bridge soft-switching converter; on the other hand additional circuiting energy is greatlyreduced. At the same time, less duty cycle loss, lower secondary parasitic resonance, widersoft-switching load range can be achieved. Based on the existing component models in the Pspicesoftware package, a combined model of IGBT is established, in which a non-linear capacitor isintroduced to replace the parasitic capacitor. Using this model, computerized simulation isconducted for the FB-ZVZCS-PWM soft-switching converter, the switching and energy-transferringcharacteristics of the power device are analyzed. Finally, based on the achievement above, a 10 kWarc welding inverter with FB-ZVZCS-PWM converter is developed. The simulation results are testifiedby experiments. It is proved that by adopting appropriate models, computerized simulation is aneffective and useful tool for the development of the arc welding inverter.展开更多
A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning...A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning electron microscopy, transmission electron microscopy, dilatometry and tensometry. Those measurements suggested that the steel consisted of martensite and retained austenite, which existed between the martensitic laths in a stable thin film, and that the steel showed very high tensile strength of 1400 MPa and good ductility of 15% in elongation after 300°C tempering.展开更多
基金This project is supported by National Natural Science Foundation of China (No.59775006)Postdoctoral Science Foundation of China (No.200031).
文摘According to the structure character of the passive sub-chain of the 3TPS-TPparallel mechanism, the kinematic constraint equations of the movable platform are established,based on which the closed-form inverse kinematics formula of the parallel mechanism are presented.Through parting the spherical joints of the active sub-chains and using the force and momentequilibrium of both the active sub-chains and passive sub-chain, the constraint forces acting on theparted joints are determined. Subsequently, the analytic expressions of the actuator driving forcesare derived by means of the force equilibrium of the upper links of active sub-chains.
文摘In order to improve nitrogen removal in anoxic/oxic(A/O) process effectively for treating domestic wastewaters, the influence factors, DO(dissolved oxygen), nitrate recirculation, sludge recycle, SRT(solids residence time), influent COD/TN and HRT(hydraulic retention time) were studied. Results indicated that it was possible to increase nitrogen removal by using corresponding control strategies, such as, adjusting the DO set point according to effluent ammonia concentration; manipulating nitrate recirculation flow according to nitrate concentration at the end of anoxic zone. Based on the experiments results, a knowledge-based approach for supervision of the nitrogen removal problems was considered, and decision trees for diagnosing nitrification and denitrification problems were built and successfully applied to A/O process.
文摘Effect of added carbon source and nitrate concentration on the denitrifying phosphorus removal by DPB sludge was systematically studied using batch experiments, at the same time the variation of ORP was investigated. Results showed that the denitrifying and phosphorus uptake rate in anoxic phase increased with the high initial anaerobic carbon source addition. However once the initial COD concentration reached a certain level, which was in excess to the PHB saturation of poly-P bacteria, residual COD carried over to anoxic phase inhibited the subsequent denitrifying phosphorus uptake. Simultaneously, phosphate uptake continued until all nitrate was removed, following a slow endogenous release of phosphate. High nitrate concentration in anoxic phase increased the initial denitrifying phosphorus rate. Once the nitrate was exhausted, phosphate uptake changed to release. Moreover, the time of this turning point occurred later with the higher nitrate addition. On the other hand, through on-line monitoring the variation of the ORP with different initial COD concentration, it was found ORP could be used as a control parameter for phosphorus release, but it is impossible to utilize ORP for controlling the denitrificaion and anoxic phosphorus uptake operations.
基金This project is supported by Municipal Natural Science Foundation of Beiiing , China (No.3032005).
文摘The piezoelectric pump with nozzle/diffuser-elements, which oscillating formdiffering from regular volumetric reciprocating or rotating pumps because there arenozzle/diffuser-elements substituted for regular valves, is a new type pump whose actuator is apiezoelectric ceramal part with verse piezoelectric effect In recent year, piezoelectric pump ispaid increasing attention to because it is an ideal candidate in application in such area as medicalhealth, mechanical tools and micro-mechanism. The fundamental research on it, however, is still notmade through. Focuses on the phenomenon of different directions of flow among Germany pump, Chinesepump and Swiss pump, which are all fitted with nozzle/diffuser-elements, and analyzes the coneangle of nozzle/diffuser-elements based on the flow equation of valve-less piezoelectric pump withnozzle/diffuser-elements. As a result, the concepts of diffuser toss coefficient and losscoefficient are introduced to explain these phenomena, from which a discussion is given on theoptimization of the cone angle of nozzle/diffuser-element aiming at the maximum of pump flow.
文摘On the basis of continuous tests and batch tests, conversion regular patterns of acetate, propionate and butyrate in activated sludge at different heights of the UASB reactor were conducted. Results indicated that the conversion capacity of the microbe is decided by the substrate characteristic when sole VFA is used as the only substrate. But when mixed substrates are used,the conversion regulations would have changed accordingly. Relationships of different substrates vary according to their locations. In the whole reactor, propionate's conversion is restrained by acetate and butyrate of high concentration. On the top and at the bottom of the reactor, conversion of acetate, but butyrate, is restrained by propionate. And in the midst, acetate's conversion is accelerated by propionate while that of butyrate is restrained. It is proved, based on the analysis of specific conversion rate, that the space distribution of the microbe is the main factor that affects substrates' conversion. The ethanol type fermentation of the acidogenic phase is the optimal acid type fermentation for the two phase anaerobic process.
基金sponsored by National Natural Science Foundation of China(50375004).
文摘A coating with high hardness, wear and oxidation resistance was prepared by electric arc spray. The hardness, bonding strength, abrasive wear and values of porosity and oxidation resistance of the coating were investigated. The microstructures and function of Cr3C2 of the coating were analyzed. The results showed surface Rockness Hardness HR30 reached 72.5 and average bond strength reached 49.1Mpa. Also porosity value was less than 2%. In addition, it was found from the comparison between the coating and 45CT coating that, oxidation resistance of the coating was less than that of 45CT, but the abrasive wear of the coating was obvious better than that of 45CT.
文摘The contributing factors for the cavitation in piezoelectric pumps areanalyzed, theoretically, and the device fitting for observing and recording is set up. With it theexperiments are carried out to observe the emergence and the flowing of the cavitations in thepiezoelectric pumps. According to the statistic and the analysis to the data of the experiments, thepeculiar features are discovered. These features are composed of balls-amassing, center-more, andflow-out.
文摘Natural daylight has more and more been used in modem buildings to save building energy consumption in China. Light pipe is one of the effective way to reduce electricity consumption for lighting, it can transmit light from outdoor to the room without generating excessive heat. Experimental apparatus of side lighting light pipe is described in this paper. Light pipe for side daylighting purpose was installed in the Key Laboratory of Enhanced Heat Transfer and Energy Conservation, Ministry of Education, Beijing University of Technology. It was 2.6m long, with diameters of 360mm.The performance of the light pipe for whole day had been measured. The highest iUuminance was 488lux on Dec.26,2002, obtained from the point beneath the center of the diffuser of the light pipe 1450mm. The ratio of internal illuminance to external was 0.23 %. Because it has many advantages to improve energy efficiency in buildings, light pipe will be populanzed in the near future in China.
基金This work was financially supported by the National Key Fundamental Research Program (973 Program) (No.G1998061316)
文摘The microstructure, mechanical properties, and electron-emission propertiesof a newly developed heated cathode material Mo-CeO_2 with 4.0% (mass fraction) of CeO_2 wereinvestigated. It is shown that the Mo-CeO_2 cathode material possesses high tensile strength andgood room-temperature ductility. After carbonized, the Mo-CeO_2 cathode material has a higher zerofield emission current density and a lower work function compared with the W-ThO_2 cathode material.
文摘The compound bioceramic coating containing calcium (Ca) and phosphorus (P) on titanium alloy substrate was prepared by means of micro-arc oxidation (MAO) treatment. The results show that under the different electrolyte the coating with the color of gray or black and surface morphology of cauliflower or honeycomb, where Ca content and P contain can attain 30% and 20% respectively, can be obtained. Meanwhile, the influences of electrolyte temperature, current density and discharge time on morphology and thickness of coating are also discussed here.
文摘AIM: To study morphologic and biomechanical changes of oesophagus in diabetes rats.METHODS: Diabetes was induced by a single injection of streptozotocin (STZ). The type of diabetes mellitus induced by parenteral STZ administration in rats was insulin-dependent (type I). The samples were excised and studied in vitro using a self-developed biomaterial test machine.RESULTS: The body mass was decreased after 4 d with STZ treatment. The length of esophagus shortened after 4, 7,14 d. The opening angle increased after 14 d. The shear,longitudinal and circumferential stiffness were obviously raised after 28 d of STZ treatment.CONCLUSION: The changes of passive biomechanical properties reflect intra-structural alteration of tissue to a certain extent. This alteration will lead to some dysfunction of movement. For example, tension of esophageal wall will change due to some obstructive disease.
基金Foundation item:Beijing Science and Technology Commission(No. H020620010120), the Significant International Projects of the National Natural Science Foundation of China(No. 50521140075), Beijing Municipal Education Commission(No. KZ200310005003) and Beijing Key Laboratories
文摘The control strategy and simulation of external carbon addition were specially studied in an anoxic-oxic(A/O) process with low carbon: nitrogen(C/N) domestic wastewater. The control strategy aimed to adjust the flow rate of external carbon dosage to the anoxic zone, thus the concentration of nitrate plus nitrite(NOx--N) in the anoxic zone was kept closed to the set point. The relationship was studied between the NOx--N concentration in the anoxic zone(S_ NO) and the dosage of external carbon, and the results showed that the removal efficiency of the total nitrogen(TN) could not be largely improved by double dosage of carbon source when S_ NO reached about 2 mg/L. Through keeping S_ NO at the level of about 2 mg/L, the demand of effluent quality could be met and the carbon dosage could be optimized. Based on the Activated Sludge Model No.1(ASM No.1), a simplified mathematical model of external carbon dosage was developed. Simulation results showed that PI controller and feed-forward PI controller both had good dynamic response and steady precision. And feed-forward PI controller had better control effects due to its consideration of influent disturbances.
文摘Measuring amplitude of signal is the usual method in wavelength demodulation of fiber Bragg grating (FBG) sensors recently. This method is easy to be disturbed and has low precision. In this paper, a novel counting wavelength demodula- tion scheme of FBG sensors using a high birefringent fiber (HBF) loop mirror is reported. This demodulator has simple structure, high precision, cheap price and convenient use. The resolution of the loop mirror device with a HBF of 30 meters long is 0.067 nm. For a center wavelength of FBG of about 1550 nm and a 40 nm shift range of its reflection wavelength, the relative error of measurement is only ± 0.001. This wavelength demodulation device has significance for widespread application of FBG sensors.
基金Supported by the National Natural Science Foundation of China(No.60402036)the Natural Science Foundation of Beijing(No.4042008).
文摘The paper describes a texture-based fast text location scheme which operates directly in the Discrete Wavelet Transform (DWT) domain. By the distinguishing texture characteristics encoded in wavelet transform domain, the text is fast detected from complex background images stored in the compressed format such as JPEG2000 without full decompress. Compared with some traditional character location methods, the proposed scheme has the advantages of low computational cost, robust to size and font of characters and high accuracy. Preliminary experimental results show that the proposed scheme is efficient and effective.
文摘AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angles of collagen fiber and the pressure it undergoes.METHODS: A kind of 2-dimensional visible quantitative analyzing technique was described. Digital image-processing method was utilized to determine the angle of collagen fiber in parenchyma according to the changes of area analyzed and further to investigate quantitatively the distribution of collagen fiber. A series of intestinal slice′s images preprocessed by polarized light were obtained with electron microscope,and they were processed to unify each pixel. The approximate angles between collagen fibers were obtained via analyzing the images and their corresponding polarized light. The relationship between the angles of collagen fiber and the pressure it undergoes were statistically summarized.RESULTS: The angle of collagen fiber in intestinal tissue was obtained with the quantitative analyzing method of calculating the ratio of different pixels. For the same slice,with polarized light angle′s variation, the corresponding ratio of different pixels was also changed; for slices under different pressures, the biggest ratio of collagen fiber area was changed either.CONCLUSION: This study suggests that the application of stress on the intestinal tissue will change the angle and content of collagen fiber. The method of calculating ratios of different pixel values to estimate collagen fiber angle was practical and reliable. The quantitative analysis used in the present study allows a larger area of soft tissue to be analyzed with relatively low cost and simple equipment.
基金This work is supported by National Natural Science Foundation of China (No. 10172010)
文摘Low-cycle fatigue experiments of tension-compression, torsion andtension-torsion with holding time were performed. The interaction law of creep and fatigue undermultiaxial stress at high temperature was investigated, and the micro-mechanism of equilibriumdiagrams was analyzed. A united equation of fatigue life under multiaxial stress was proposed.
基金This project is supported by Provincial Natural Science Foundation of Shanxi (No.546).
文摘A high-speed photographic method is mainly used to analyze metal transfer ofa cellulose covered electrode in the vertical down welding. The experimental results show that finedroplets spraying transfer and globular transfer are the dominant transfer characteristic. The largedroplet spatter, especially the upwards spatter, is a particular phenomenon. It is found that thecombination action of gas blow force, surface tension, gravitational force and electromagnetic forcelead to globular transfer. Gravitational force and electromagnetic force, which hasten big dropletspatter, should not be neglected.
基金This project is supported by National Natural Science Foundation of China(No.50075003)Municipal Natural Science Foundation of Beijing, China(No.3001001).
文摘The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power device of the static leg becomes azero-current-switch (ZCS), power device of the shifted leg becomes a zero-voltage-switch(ZVS). Thus,on one hand IGBT (Insulated gate bipolar transistor) with tail current can be easily used infull-bridge soft-switching converter; on the other hand additional circuiting energy is greatlyreduced. At the same time, less duty cycle loss, lower secondary parasitic resonance, widersoft-switching load range can be achieved. Based on the existing component models in the Pspicesoftware package, a combined model of IGBT is established, in which a non-linear capacitor isintroduced to replace the parasitic capacitor. Using this model, computerized simulation isconducted for the FB-ZVZCS-PWM soft-switching converter, the switching and energy-transferringcharacteristics of the power device are analyzed. Finally, based on the achievement above, a 10 kWarc welding inverter with FB-ZVZCS-PWM converter is developed. The simulation results are testifiedby experiments. It is proved that by adopting appropriate models, computerized simulation is aneffective and useful tool for the development of the arc welding inverter.
文摘A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning electron microscopy, transmission electron microscopy, dilatometry and tensometry. Those measurements suggested that the steel consisted of martensite and retained austenite, which existed between the martensitic laths in a stable thin film, and that the steel showed very high tensile strength of 1400 MPa and good ductility of 15% in elongation after 300°C tempering.
