This study proposes to use the unconfined compressive strength(UCS)and the bender element(BE)tests for determining the strength and the initial small-strain shear modulus of Bangkok soft marine clay improved by cement...This study proposes to use the unconfined compressive strength(UCS)and the bender element(BE)tests for determining the strength and the initial small-strain shear modulus of Bangkok soft marine clay improved by cement and polyester fibers.This study varies the content of admixed cement(1%–20%)and polyester fibers(0–20%),including the curing time(3–28 d)for preparing 360 samples.Moreover,this study uses the Michaelis-Menten kinetics concept to model cement hydration saturation.From the study,it is concluded as follows.The modelled results reveals that at least 10%cement and 1%polyester fiber are recommended to attain the 28-d UCS standards(294 kPa)for highway subgrade materials in Thailand.This also fulfils sustainable construction due to reducing normal-use cement from 20%to 10%.Unfortunately,the addition of polyester fibers into the Bangkok clay with at least 5%cement reduces shear modulus by 1.12–1.32 times.The Abram's relationship between shear modulus and the mixing-water-to-cement ratio is found time-dependent.From the composite theory,the BE detects the polyester fiber zone as a defect in the Bangkok clay(matrix)with 5%–20%cement.So,the 28-d shear modulus in the polyester fiber zone is negative(up to0.034 MPa for 20%fiber),similar to softening phenomenon in concrete cracking(negative stiffness).For the 28-d shear modulus of fiber zone,the optimum cement content is around 2%for the positive influences of polyester fibers.Experimentally,the timedependent normalized UCS for 10%and 20%cement is compatible with other studies,and its development rate increases with the cement content as 0.3017,0.3172 and 0.3204 for 5%,10%and 20%cement,respectively.The 28-d relationship between shear modulus and UCS shows that low-cement soft clay requires high polyester fiber content(5%–20%)to activate UCS improvement.However,the soft clay with enough cement(20%)causes the uniformly distributed UCS improvement.展开更多
Nano-silica treated with different kinds of coupling agent （KH550, A-143, A-151） was used to modify the surface condition of glass fiber, and then, the modified glass fiber/unsaturated polyester resin （UPR） compos...Nano-silica treated with different kinds of coupling agent （KH550, A-143, A-151） was used to modify the surface condition of glass fiber, and then, the modified glass fiber/unsaturated polyester resin （UPR） composites materials were prepared. Scanning electron microscopy （SEM）, dynamic mechanical analysis （DMA）, and impact test were used to characterize the composite materials＇ structure and properties. The morphology of composite materials shows that the adhesion between nano-silica and glass fiber is improved when silane coupling agent is added in. The DMA and impact test results show that silane coupling agent （especially KH550 and A-151） could effectively improve the composite＇s mechanical properties. When the dose of KH550 was 0.1% （m ： m）, the storage modulus and impact strength reached the maximum.展开更多
The main objective of this study is to investigate the effects of the nanoclay mixed with recycled polyester fiber on the mechanical behavior of soil as a new stabilizer material.To meet this objective,a series of dra...The main objective of this study is to investigate the effects of the nanoclay mixed with recycled polyester fiber on the mechanical behavior of soil as a new stabilizer material.To meet this objective,a series of drained direct shear and compaction tests were performed on unreinforced and reinforced soil specimens with three different combinations of the fiber-soil ratios ranging between 0.1%and 0.5%,as well as three different combinations of nanoclay soil ratios ranging between 0.5%and 1.5%of the soil dry weight.Results indicated that composition of the nanoclay recycled polyester fiber with the soil improved the friction angle(Φ)by 41%and cohesion(c)by 174%.The soil particles stick together through viscose gel produced by nanoclay.In addition,the rough and wavy surface of the fibers creates a bond and friction between the soil particles and prevents the movement of soil particles,and as a result,the soil strength is increased.展开更多
Abstract A newly developed coaxial dielectric barrier discharge reactor with a length of 1000 mm at an atmospheric pressure was used for plasma treatment of polyester fiber cord in a roll-to-roll manner. In this react...Abstract A newly developed coaxial dielectric barrier discharge reactor with a length of 1000 mm at an atmospheric pressure was used for plasma treatment of polyester fiber cord in a roll-to-roll manner. In this reactor, swirling mixture gases of oxygen of about 1% and argon with a flow rate of 1.5 L/rain to 2.7 L/min ensured the gas usage sparing, discharge uniformity and efficient fiber surface modification. The water contact angle and surface morphology of the treated fiber were measured. The results show that the surface oxygenation is mainly responsible for the wettability improvement of the fiber cord when passing through the plasma zone at a linear speed of 3 m/min to 8 m/rain. The specimens of modified-polyester fiber reinforced rubber composite were also prepared for the interracial shear strength tests. Furthermore, the effect of adding oxygen into argon discharge on the fiber surface oxidation was correlated with optical emission spectroscopy. Finally, the effect of adding oxygen into argon discharge on the kinetic processes of the active species generation were also analyzed.展开更多
Modified polyester fibers were obtained using 2% and 6% of kaolin blends through melt spinning.The influences of two thermal treatments maintaining the original tension(180 ℃×2 min and 200 ℃×1 min)on the s...Modified polyester fibers were obtained using 2% and 6% of kaolin blends through melt spinning.The influences of two thermal treatments maintaining the original tension(180 ℃×2 min and 200 ℃×1 min)on the structure and properties of fiber were compared.The changes of grain size and crystallinity of fiber were investigated by X-ray diffraction(XRD).The changes of thermal properties of fibers were analyzed using dynamic mechanical analyzer(DMA).The results show that the crystalline structure of kaolin modified polyester fiber doesn't change with the thermal treatment.With the kaolin content increasing,the grain size of fiber changed.The higher the thermal treatment temperature is,the higher the crystallinity of fiber is.There are two glass-transition temperatures for kaolin modified:the lower one is the glass-transition temperature of polyester fiber matrix,and the higher one is derived from the heterogeneous blend of polyester matrix and nano kaolin.The higher the kaolin content is,the higher the glass-transition temperature is.Thermal treatment could increase the compatibility of polyester matrix and nano kaolin.There was only one glass-transition temperature for the thermal treatment fiber,and the heat resistance of fiber was improved.Thermogravimetric analysis-differential scanning calorimetry(TGA-DSC)results of kaolin modified polyethylene terephthalate(PET)matrix indicate that the decomposition temperature of PET fibers,kaolin modified PET fibers,and thermal treated fibers were little different within 40%-60% of weight loss rate range.展开更多
Cation Dyeable Polyester(CDP)was made by copolymerizing dimethyl terephthalate(DMT),S-sodium sulfonate dimethyl isophthalate(SIPM) with a weight fraction of 4.5% and ethyleneglycol (EG).Blend of PET and CDP was spun i...Cation Dyeable Polyester(CDP)was made by copolymerizing dimethyl terephthalate(DMT),S-sodium sulfonate dimethyl isophthalate(SIPM) with a weight fraction of 4.5% and ethyleneglycol (EG).Blend of PET and CDP was spun into hollow fiber.The fiber was then treated withaqueous NaOH.In this paper,kinetics and mechanism of alkaline hydrolysis of PET,CDP andtheir blend PET/CDP fiber were studied by means of specific area measurement,scantling elec-tron microscopy and other chemical analyses.It was showed that the rate of alkaline hydrolysis isCDP】PET/CDP】PET.Because of blending effect,the alkaline hydrolysis of PET/CDP is dif-ferent from that of PET.CDP phase in the PET/CDP fiber is predominantly hydrolyzed,andhence some pieces of fiber(micro-fiber) fall off the fiber because of etching.展开更多
This paper deals with the fracture feature of three kinds of polyester fibers with differentstructures under different tensile conditions.We studied fracture initiation,crack propagationand ultimate fracture character...This paper deals with the fracture feature of three kinds of polyester fibers with differentstructures under different tensile conditions.We studied fracture initiation,crack propagationand ultimate fracture characteristics under tension of polyester fibers.The fracture features ofpolyester fibers are related with fiber structure and tensile condition.Crack is initiated in fibersurface.It propagates from outside to inside and eventually causes rupture of the fiber.In addi-tion,it is stated also that the analysis on tensile fracture feature of fibers might be confirmed bydynamic testing technique of scanning electron microscopy.展开更多
Ultrafine polypropylene fibers are prepared frompolypropylene/easily hydro - degraded polyester （PP/EHDPET） blend fibers, in which file EHDPET compo-nent is degradable by treating with NaOH - H<sub>2</sub&g...Ultrafine polypropylene fibers are prepared frompolypropylene/easily hydro - degraded polyester （PP/EHDPET） blend fibers, in which file EHDPET compo-nent is degradable by treating with NaOH - H<sub>2</sub>O solu-tion. We investigated the morphology of PP/EHDPETblend fibers before and after stretching and alkalinehydrolysis. Then thermal behavior of the blend has alsobeen studied.展开更多
Highloft nonwoven was produced by heat bonding of bicomponent polyester fibers. The effect of fiber properties and processing parameters on the mechanical properties of the nonwoven was investigated. The heat bonding ...Highloft nonwoven was produced by heat bonding of bicomponent polyester fibers. The effect of fiber properties and processing parameters on the mechanical properties of the nonwoven was investigated. The heat bonding processing parameters for the nonwoven were optimized. The results show that the range of processing temperature is wider while the shell melting point of the bicomponent fibers (Tm1) is lower. The best processing temperature is about 15℃ higher than Tm1 while the shell melting point (Tm1) is higher.展开更多
Wood-plastic composite is an environmentally friendly material,due to its use of recycled thermoplastics and plant fibers.However,its surface lacks attractive aesthetic qualities.In this paper,a method of decorating w...Wood-plastic composite is an environmentally friendly material,due to its use of recycled thermoplastics and plant fibers.However,its surface lacks attractive aesthetic qualities.In this paper,a method of decorating wood fiber/high-density polyethylene(WF/HDPE)without adding adhesive was explored.Canvas or polyester fabrics were selected as the surface decoration materials.The influence of hot-pressing temperature and WF/HDPE ratio on the adhesion was studied.The surface bonding strength,water resistance,and surface color were evaluated,and observation within the infrared spectrum and under scanning electron microscopy was used to analyze the bonding process.The results showed that the fabric and WF/HDPE substrate could be closely laminated together depending on the HDPE layer accumulated on the WF/HDPE surface.The molten HDPE matrix penetrates canvas more easily than polyester fabric,and the canvasveneered composite shows a greater bonding strength than does the polyester fabric-veneered composite.A higher proportion of the thermoplastic component in the substrate improved the bonding.When the hot-pressing temperature exceeded 160°C,the fabric-veneered WF/HDPE panels had greater water resistance,although the canvas fabric changed more obviously in terms of fiber shape and color,compared with the polyester fabric.For the canvas fabric,140°C–160°C was a suitable hot-pressing temperature,whereas 160°C–180°C was more suitable for polyester fabric.The proportion of the thermoplastic component in the composite should be not less than 30%to achieve adequate bonding strength.展开更多
The removal of surface oligomers from polyester fiber was investigated by an Ultrasonic / Alkali System. Effects of concentration of alkali, temperature, time and ultrasonic frequency were discussed. It was found tbat...The removal of surface oligomers from polyester fiber was investigated by an Ultrasonic / Alkali System. Effects of concentration of alkali, temperature, time and ultrasonic frequency were discussed. It was found tbat Ultrasonic / Alkali System could decrease remarkably surface oligomers content of polyester fiber dyed by HIP without influencing the dyeing properties of the fiber.展开更多
The water collector is operated in the humid and hot environment of the cooling tower all the year round.It also needs to carry part of the weight of water and silt.Therefore,it is particularly critical to optimize th...The water collector is operated in the humid and hot environment of the cooling tower all the year round.It also needs to carry part of the weight of water and silt.Therefore,it is particularly critical to optimize the material of the water collector and improve its mechanical properties.Polyester,a general term of polymer obtained from polyols and polyacids,is a kind of engineering plastics with excellent properties and wide applications.Glass fiber is a reinforced plastic reinforcement material,and the biggest characteristic of it is the high tensile strength and good heat resistance.In this paper,glass fiber reinforced polyester resin composite material is prepared,its tensile properties and bending properties are tested,and the performance of the imported material JK2020B is compared and analyzed.The results show that the elastic modulus along the fiber direction is relatively high,but the interlayer force in the direction of thickness and width is very small.This review provides a guidance for production process.展开更多
The paper shows the results of method development identification of colloidal silver nanoparticles on the components of the Raman spectra, using the conditions information uncertainty decision to increase the reliabil...The paper shows the results of method development identification of colloidal silver nanoparticles on the components of the Raman spectra, using the conditions information uncertainty decision to increase the reliability evaluating the presence nanoparticles at the surface polyester fibers.展开更多
基金allocated by National Science,Research and Innovation Fund(NSRF)King Mongkut's University of Technology North Bangkok(project no.KMUTNB-FF-67-B-44 and KMUTNB-FF-67-B-45)supported by the NSRF through the Program Management Unit for Human Resources&Institutional Development,Research and Innovation(grant no.B40G660036).
文摘This study proposes to use the unconfined compressive strength(UCS)and the bender element(BE)tests for determining the strength and the initial small-strain shear modulus of Bangkok soft marine clay improved by cement and polyester fibers.This study varies the content of admixed cement(1%–20%)and polyester fibers(0–20%),including the curing time(3–28 d)for preparing 360 samples.Moreover,this study uses the Michaelis-Menten kinetics concept to model cement hydration saturation.From the study,it is concluded as follows.The modelled results reveals that at least 10%cement and 1%polyester fiber are recommended to attain the 28-d UCS standards(294 kPa)for highway subgrade materials in Thailand.This also fulfils sustainable construction due to reducing normal-use cement from 20%to 10%.Unfortunately,the addition of polyester fibers into the Bangkok clay with at least 5%cement reduces shear modulus by 1.12–1.32 times.The Abram's relationship between shear modulus and the mixing-water-to-cement ratio is found time-dependent.From the composite theory,the BE detects the polyester fiber zone as a defect in the Bangkok clay(matrix)with 5%–20%cement.So,the 28-d shear modulus in the polyester fiber zone is negative(up to0.034 MPa for 20%fiber),similar to softening phenomenon in concrete cracking(negative stiffness).For the 28-d shear modulus of fiber zone,the optimum cement content is around 2%for the positive influences of polyester fibers.Experimentally,the timedependent normalized UCS for 10%and 20%cement is compatible with other studies,and its development rate increases with the cement content as 0.3017,0.3172 and 0.3204 for 5%,10%and 20%cement,respectively.The 28-d relationship between shear modulus and UCS shows that low-cement soft clay requires high polyester fiber content(5%–20%)to activate UCS improvement.However,the soft clay with enough cement(20%)causes the uniformly distributed UCS improvement.
基金Supported by the National Natural Science Foundation of of China(J1210061)
文摘Nano-silica treated with different kinds of coupling agent （KH550, A-143, A-151） was used to modify the surface condition of glass fiber, and then, the modified glass fiber/unsaturated polyester resin （UPR） composites materials were prepared. Scanning electron microscopy （SEM）, dynamic mechanical analysis （DMA）, and impact test were used to characterize the composite materials＇ structure and properties. The morphology of composite materials shows that the adhesion between nano-silica and glass fiber is improved when silane coupling agent is added in. The DMA and impact test results show that silane coupling agent （especially KH550 and A-151） could effectively improve the composite＇s mechanical properties. When the dose of KH550 was 0.1% （m ： m）, the storage modulus and impact strength reached the maximum.
文摘The main objective of this study is to investigate the effects of the nanoclay mixed with recycled polyester fiber on the mechanical behavior of soil as a new stabilizer material.To meet this objective,a series of drained direct shear and compaction tests were performed on unreinforced and reinforced soil specimens with three different combinations of the fiber-soil ratios ranging between 0.1%and 0.5%,as well as three different combinations of nanoclay soil ratios ranging between 0.5%and 1.5%of the soil dry weight.Results indicated that composition of the nanoclay recycled polyester fiber with the soil improved the friction angle(Φ)by 41%and cohesion(c)by 174%.The soil particles stick together through viscose gel produced by nanoclay.In addition,the rough and wavy surface of the fibers creates a bond and friction between the soil particles and prevents the movement of soil particles,and as a result,the soil strength is increased.
基金supported by National Natural Science Foundation of China (No.11075033)Mehler Engineered Products (Suzhou) Co. Ltd. of China
文摘Abstract A newly developed coaxial dielectric barrier discharge reactor with a length of 1000 mm at an atmospheric pressure was used for plasma treatment of polyester fiber cord in a roll-to-roll manner. In this reactor, swirling mixture gases of oxygen of about 1% and argon with a flow rate of 1.5 L/rain to 2.7 L/min ensured the gas usage sparing, discharge uniformity and efficient fiber surface modification. The water contact angle and surface morphology of the treated fiber were measured. The results show that the surface oxygenation is mainly responsible for the wettability improvement of the fiber cord when passing through the plasma zone at a linear speed of 3 m/min to 8 m/rain. The specimens of modified-polyester fiber reinforced rubber composite were also prepared for the interracial shear strength tests. Furthermore, the effect of adding oxygen into argon discharge on the fiber surface oxidation was correlated with optical emission spectroscopy. Finally, the effect of adding oxygen into argon discharge on the kinetic processes of the active species generation were also analyzed.
文摘Modified polyester fibers were obtained using 2% and 6% of kaolin blends through melt spinning.The influences of two thermal treatments maintaining the original tension(180 ℃×2 min and 200 ℃×1 min)on the structure and properties of fiber were compared.The changes of grain size and crystallinity of fiber were investigated by X-ray diffraction(XRD).The changes of thermal properties of fibers were analyzed using dynamic mechanical analyzer(DMA).The results show that the crystalline structure of kaolin modified polyester fiber doesn't change with the thermal treatment.With the kaolin content increasing,the grain size of fiber changed.The higher the thermal treatment temperature is,the higher the crystallinity of fiber is.There are two glass-transition temperatures for kaolin modified:the lower one is the glass-transition temperature of polyester fiber matrix,and the higher one is derived from the heterogeneous blend of polyester matrix and nano kaolin.The higher the kaolin content is,the higher the glass-transition temperature is.Thermal treatment could increase the compatibility of polyester matrix and nano kaolin.There was only one glass-transition temperature for the thermal treatment fiber,and the heat resistance of fiber was improved.Thermogravimetric analysis-differential scanning calorimetry(TGA-DSC)results of kaolin modified polyethylene terephthalate(PET)matrix indicate that the decomposition temperature of PET fibers,kaolin modified PET fibers,and thermal treated fibers were little different within 40%-60% of weight loss rate range.
文摘Cation Dyeable Polyester(CDP)was made by copolymerizing dimethyl terephthalate(DMT),S-sodium sulfonate dimethyl isophthalate(SIPM) with a weight fraction of 4.5% and ethyleneglycol (EG).Blend of PET and CDP was spun into hollow fiber.The fiber was then treated withaqueous NaOH.In this paper,kinetics and mechanism of alkaline hydrolysis of PET,CDP andtheir blend PET/CDP fiber were studied by means of specific area measurement,scantling elec-tron microscopy and other chemical analyses.It was showed that the rate of alkaline hydrolysis isCDP】PET/CDP】PET.Because of blending effect,the alkaline hydrolysis of PET/CDP is dif-ferent from that of PET.CDP phase in the PET/CDP fiber is predominantly hydrolyzed,andhence some pieces of fiber(micro-fiber) fall off the fiber because of etching.
文摘This paper deals with the fracture feature of three kinds of polyester fibers with differentstructures under different tensile conditions.We studied fracture initiation,crack propagationand ultimate fracture characteristics under tension of polyester fibers.The fracture features ofpolyester fibers are related with fiber structure and tensile condition.Crack is initiated in fibersurface.It propagates from outside to inside and eventually causes rupture of the fiber.In addi-tion,it is stated also that the analysis on tensile fracture feature of fibers might be confirmed bydynamic testing technique of scanning electron microscopy.
文摘Ultrafine polypropylene fibers are prepared frompolypropylene/easily hydro - degraded polyester （PP/EHDPET） blend fibers, in which file EHDPET compo-nent is degradable by treating with NaOH - H<sub>2</sub>O solu-tion. We investigated the morphology of PP/EHDPETblend fibers before and after stretching and alkalinehydrolysis. Then thermal behavior of the blend has alsobeen studied.
文摘Highloft nonwoven was produced by heat bonding of bicomponent polyester fibers. The effect of fiber properties and processing parameters on the mechanical properties of the nonwoven was investigated. The heat bonding processing parameters for the nonwoven were optimized. The results show that the range of processing temperature is wider while the shell melting point of the bicomponent fibers (Tm1) is lower. The best processing temperature is about 15℃ higher than Tm1 while the shell melting point (Tm1) is higher.
基金supported by the National Natural Science Foundation of China[31670573]the Innovation Training Program of Northeast Forestry University[201810225398].
文摘Wood-plastic composite is an environmentally friendly material,due to its use of recycled thermoplastics and plant fibers.However,its surface lacks attractive aesthetic qualities.In this paper,a method of decorating wood fiber/high-density polyethylene(WF/HDPE)without adding adhesive was explored.Canvas or polyester fabrics were selected as the surface decoration materials.The influence of hot-pressing temperature and WF/HDPE ratio on the adhesion was studied.The surface bonding strength,water resistance,and surface color were evaluated,and observation within the infrared spectrum and under scanning electron microscopy was used to analyze the bonding process.The results showed that the fabric and WF/HDPE substrate could be closely laminated together depending on the HDPE layer accumulated on the WF/HDPE surface.The molten HDPE matrix penetrates canvas more easily than polyester fabric,and the canvasveneered composite shows a greater bonding strength than does the polyester fabric-veneered composite.A higher proportion of the thermoplastic component in the substrate improved the bonding.When the hot-pressing temperature exceeded 160°C,the fabric-veneered WF/HDPE panels had greater water resistance,although the canvas fabric changed more obviously in terms of fiber shape and color,compared with the polyester fabric.For the canvas fabric,140°C–160°C was a suitable hot-pressing temperature,whereas 160°C–180°C was more suitable for polyester fabric.The proportion of the thermoplastic component in the composite should be not less than 30%to achieve adequate bonding strength.
文摘The removal of surface oligomers from polyester fiber was investigated by an Ultrasonic / Alkali System. Effects of concentration of alkali, temperature, time and ultrasonic frequency were discussed. It was found tbat Ultrasonic / Alkali System could decrease remarkably surface oligomers content of polyester fiber dyed by HIP without influencing the dyeing properties of the fiber.
文摘The water collector is operated in the humid and hot environment of the cooling tower all the year round.It also needs to carry part of the weight of water and silt.Therefore,it is particularly critical to optimize the material of the water collector and improve its mechanical properties.Polyester,a general term of polymer obtained from polyols and polyacids,is a kind of engineering plastics with excellent properties and wide applications.Glass fiber is a reinforced plastic reinforcement material,and the biggest characteristic of it is the high tensile strength and good heat resistance.In this paper,glass fiber reinforced polyester resin composite material is prepared,its tensile properties and bending properties are tested,and the performance of the imported material JK2020B is compared and analyzed.The results show that the elastic modulus along the fiber direction is relatively high,but the interlayer force in the direction of thickness and width is very small.This review provides a guidance for production process.
文摘The paper shows the results of method development identification of colloidal silver nanoparticles on the components of the Raman spectra, using the conditions information uncertainty decision to increase the reliability evaluating the presence nanoparticles at the surface polyester fibers.
