With the increasing demand of recycling disposal of industrial wastewater,oil-in-water(O/W)emulsion has been paid much attention in recent years owing to its high oil con-tent.However,due to the presence of surfactant...With the increasing demand of recycling disposal of industrial wastewater,oil-in-water(O/W)emulsion has been paid much attention in recent years owing to its high oil con-tent.However,due to the presence of surfactant and salt,the emulsion was usually stable with complex physicochemical interfacial properties leading to increased processing diffi-culty.Herein,a novel flow-through electrode-based demulsification reactor(FEDR)was well designed for the treatment of saline O/W emulsion.In contrast to 53.7%for electrical demul-sification only and 80.3%for filtration only,the COD removal efficiency increased to 92.8%under FEDR system.Moreover,the pore size of electrode and the applied voltage were two key factors that governed the FEDR demulsification performance.By observing the mor-phology of oil droplets deposited layer after different operation conditions and the behavior of oil droplets at the electrode surface under different voltage conditions,the mechanism was proposed that the oil droplets first accumulated on the surface of flow-through elec-trode by sieving effect,subsequently the gathered oil droplets could further coalesce with the promoting effect of the anode,leading to a high-performing demulsification.This study offers an attractive option of using flow-through electrode to accomplish the oil recovery with simultaneous water purification.展开更多
Magnetic particles were coupled with a flocculant to enhance the demulsification and separation of waste cutting emulsions.The optimal magnetic particle size and critical magnetic field conditions were investigated to...Magnetic particles were coupled with a flocculant to enhance the demulsification and separation of waste cutting emulsions.The optimal magnetic particle size and critical magnetic field conditions were investigated to achieve large-scale engineering application of magnetic demulsification separation for waste cutting emulsion treatment.The micro-scale magnetic particles were found to show comparable effects to nano-scale magnetic particles on enhancing the demulsification and separation of cutting emulsions,which are beneficial for broadening the selectivity of low-cost magnetic particles.The critical magnetic separation region was determined to be an area 40 mm from the magnetic field source.Compared to the flocculant demulsification,the magnetic demulsification separation exhibited a significant advantage in accelerating flocs-water separation by decreasing the separation time of flocs from 180-240 min to less than 15 min,compressing the flocs by reducing the floc volume ratio from 60%-90%to lower than 20%,and showing excellent adaptability to the variable properties of waste cutting emulsions.Coupled with the design of the magnetic disk separator,continuous demulsification separation of the waste cutting emulsion was achieved at 1.0 t/hr for at least 10 hr to obtain clear effluent with 81%chemical oxygen demand removal and 89%turbidity reduction.This study demonstrates the feasibility of applying magnetic demulsification separation to large-scale continuous treatment of waste emulsion.Moreover,it addresses the flocs-water separation problems that occur in practical flocculant demulsification engineering applications.展开更多
Demulsification of emulsified water-in-oil droplets was worked out with the employment of wetting coalescence materials. Demulsification is carried out in conventional stirred-column and packed-column. Among the four ...Demulsification of emulsified water-in-oil droplets was worked out with the employment of wetting coalescence materials. Demulsification is carried out in conventional stirred-column and packed-column. Among the four kinds of natural fibers and two kinds of inorganic materials tested, natural fiber A, originated from wood shavings was found to give the best performance of demulsification. The demulsification efficiency can exceed 96.5% when demulsification conditions are optimized. The packed-column showed much better performance both in terms of demulsification efficiency and repeated use of the recovered oil phase for extracting cadmium in simulated wastewater. Operating variables governing the demulsification efficiency were investigated.展开更多
Extraction behavior of chlorpromazine hydrochloride (CPZ) and procaine hydro- chloride (PCN) in the system described in the title was studied. Research shows that the extraction efficiency of CPZ can amount to 96% by...Extraction behavior of chlorpromazine hydrochloride (CPZ) and procaine hydro- chloride (PCN) in the system described in the title was studied. Research shows that the extraction efficiency of CPZ can amount to 96% by twice extraction, while that of PCN is 77%. This system produces the distribution coefficients (KD) of 12.3 and 2.6 respectively for CPZ and PCN. Extraction mechanism is deduced according to ultraviolet and molecular fluorescence spectra variation of the drugs in the system studied.展开更多
A spectrophotometric approach for the detection of non-ionic surfactant (Triton X-100) has been proposed in this paper. This method does not involve extraction of the ion-associate with harmful solvents, but employs a...A spectrophotometric approach for the detection of non-ionic surfactant (Triton X-100) has been proposed in this paper. This method does not involve extraction of the ion-associate with harmful solvents, but employs adhesion of the ion-association of potassium/non-ionic surfactants complex and tetraphenylporphyrin tetrasulfonic acid obtained by vigorous shaking. The adhered ion-associate was dissolved with water and its absorbance was measured. The sensitivity for Triton X-100 was determined to be 0.146 (expressed as absorbance of 1 mg/L solution). The adhesion tendency of ion-associate was found to be dependent on the water contact angle, which in turn was influenced by a high adhesion of the ion-associate and by low blank values. In this respect, a tetrafluo-roethylene vessel was found to be the most suitable for the detection of non-ionic surfactants. This spectrophotometrical method is simply and rapidly performed by a procedure based on mechanical shaking and can be employed to detect non-ionic surfactants containing more than 7 polyethylene oxide units.展开更多
The hydrophilic porous glass membranes were used to demulsify water in oil emulsion, liquid membrane and demulsification efficiency can reach more than 96 percent. Effects of pore size of the membrane, transmembrane p...The hydrophilic porous glass membranes were used to demulsify water in oil emulsion, liquid membrane and demulsification efficiency can reach more than 96 percent. Effects of pore size of the membrane, transmembrane pressure and volumetric ratio of oil phase to internal aqueous phase in the emulsion on demulsification were investigated. Correspondingly, effect of transmembrane pressure on permeation flux of the droplets was also studied.展开更多
A study on the membrane coalescence demulsification was carried out with four working systems of water/n-butyl alcohol, water/n-octanol, water/30% TBP(in kerosene) and water/kerosene. The membranes made of polytetrafl...A study on the membrane coalescence demulsification was carried out with four working systems of water/n-butyl alcohol, water/n-octanol, water/30% TBP(in kerosene) and water/kerosene. The membranes made of polytetrafluoroethylene (PTFE) with 1.0μm pore size were used. The results indicated that the excellent demulsification efficiency for emulsions with various oil contents was obtained. A conductivity probe was used to study the demulsification mechanism. An electrode probe was designed and used to determine the oil content near the membrane surface. The obtained data showed that the oil content in the permeated stream was much higher than that in the feed emulsion. A physical mechanism to explain the membrane demulsification was put forward.展开更多
As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsifica...As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsification behavior,characteristics,and stages under BPEF were explored.It was discovered that BPEF drove SSO/W emulsion to move and form vortexes,during which the oil droplets aggregated and accumulated to generate an oil droplet layer(ODL).ODL subsequently transformed into a continuous oil layer(COL)leading to the demulsification and separation of SSO/W emulsion.The conversion rate of ODL to COL was defined and used to evaluate the demulsification process and reflect the coalescence ability and transformation efficiency of dispersed oil droplets into COL.Furthermore,the effects of BPEF voltage,frequency,duty cycle,ratio of pulse output time,and surfactant type and content on the demulsification performance were examined.The optimal values of BPEF parameters for demulsification operation were 400 V,25 Hz,50%,and 4:1.O/W emulsion containing anionic surfactant was apt to be demulsified by BPEF,nonionic surfactant took the second place and cationic surfactant was the most difficult.A high surfactant content was not conducive to the BPEF demulsification.This work is anticipated to provide useful guidance for oil/water separation and oil recovery from actual emulsified oily wastewater by BPEF.展开更多
A simple and rapid method for the determination of polyethylene oxide-type non-ionic surfactants is reported herein. This method is based on the adhesion of calcium/non-ionic surfactant complexes with tetra phenyl por...A simple and rapid method for the determination of polyethylene oxide-type non-ionic surfactants is reported herein. This method is based on the adhesion of calcium/non-ionic surfactant complexes with tetra phenyl porphine sulfonic acid （TPPS） to the wall of reaction vessel upon vigorous shaking. The ion-associate adhering to the inner wall of the vessel was dissolved with water after discarding the solution and spectrophotometrically assayed at 412 nm. From the standard curve for Triton X-100, the order of the sensitivity for different ions was as follows： Ca^2＋〉 K^＋〉 NH4^＋〉 Ba^2＋. The proposed method does not involve extraction of the ion-associated with harmful solvents and can be simply performed by combining a procedure based on hand shaking and the use of a spectrophotometer.展开更多
An improved rotating microchannel(IRM) separator was further explored in the intensification for demulsification and separation process. Oil-in-water(O/W) emulsion system of 2-ethylhexyl phosphoric acid-2-ethylhexyl e...An improved rotating microchannel(IRM) separator was further explored in the intensification for demulsification and separation process. Oil-in-water(O/W) emulsion system of 2-ethylhexyl phosphoric acid-2-ethylhexyl ester(P507)–water without emulsifier was employed to evaluate the performance of the new equipment. In this experiment, the influence on demulsification separation process was explored by changing the geometrical structure and channel height of the microchannel and combining the liquid–liquid two-phase flow pattern, and the correlation general graph between demulsification efficiency and dimensionless parameters was established. The total demulsification effect of the IRM and the separation capacity of the clear organic phase recovered from demulsification are significantly improved. In addition, the liquid–liquid two-phase flow pattern of the clear organic phase after demulsification and the remaining emulsion in the IRM are observed and recorded by high-speed photography. The separation ability of organic phase from the upper outlet can be significantly improved when the total demulsification rate of IRM is up to 90%. There are 3 types and 6 kinds of flow patterns observed. The results demonstrated that the suitable demulsification performance is obtained when the liquid–liquid two-phase inside the IRM is in a parallel pattern. Finally, the relation map between total demulsification efficiency and the universal flow is drawn, which provides a basis for the accurate control of the IRM device.展开更多
基金supported by the National Natural Science Foundation of China(Nos.22022606 and 52221004).
文摘With the increasing demand of recycling disposal of industrial wastewater,oil-in-water(O/W)emulsion has been paid much attention in recent years owing to its high oil con-tent.However,due to the presence of surfactant and salt,the emulsion was usually stable with complex physicochemical interfacial properties leading to increased processing diffi-culty.Herein,a novel flow-through electrode-based demulsification reactor(FEDR)was well designed for the treatment of saline O/W emulsion.In contrast to 53.7%for electrical demul-sification only and 80.3%for filtration only,the COD removal efficiency increased to 92.8%under FEDR system.Moreover,the pore size of electrode and the applied voltage were two key factors that governed the FEDR demulsification performance.By observing the mor-phology of oil droplets deposited layer after different operation conditions and the behavior of oil droplets at the electrode surface under different voltage conditions,the mechanism was proposed that the oil droplets first accumulated on the surface of flow-through elec-trode by sieving effect,subsequently the gathered oil droplets could further coalesce with the promoting effect of the anode,leading to a high-performing demulsification.This study offers an attractive option of using flow-through electrode to accomplish the oil recovery with simultaneous water purification.
基金supported by the National Natural Science Foundation of China(No.51978490)Natural Science Foun-dation of Shanghai(No.20ZDR1461200)the Major Sci-ence and Technology Program for Water Pollution Control and Treatment,China(No.2017ZX07202003-02).
文摘Magnetic particles were coupled with a flocculant to enhance the demulsification and separation of waste cutting emulsions.The optimal magnetic particle size and critical magnetic field conditions were investigated to achieve large-scale engineering application of magnetic demulsification separation for waste cutting emulsion treatment.The micro-scale magnetic particles were found to show comparable effects to nano-scale magnetic particles on enhancing the demulsification and separation of cutting emulsions,which are beneficial for broadening the selectivity of low-cost magnetic particles.The critical magnetic separation region was determined to be an area 40 mm from the magnetic field source.Compared to the flocculant demulsification,the magnetic demulsification separation exhibited a significant advantage in accelerating flocs-water separation by decreasing the separation time of flocs from 180-240 min to less than 15 min,compressing the flocs by reducing the floc volume ratio from 60%-90%to lower than 20%,and showing excellent adaptability to the variable properties of waste cutting emulsions.Coupled with the design of the magnetic disk separator,continuous demulsification separation of the waste cutting emulsion was achieved at 1.0 t/hr for at least 10 hr to obtain clear effluent with 81%chemical oxygen demand removal and 89%turbidity reduction.This study demonstrates the feasibility of applying magnetic demulsification separation to large-scale continuous treatment of waste emulsion.Moreover,it addresses the flocs-water separation problems that occur in practical flocculant demulsification engineering applications.
文摘Demulsification of emulsified water-in-oil droplets was worked out with the employment of wetting coalescence materials. Demulsification is carried out in conventional stirred-column and packed-column. Among the four kinds of natural fibers and two kinds of inorganic materials tested, natural fiber A, originated from wood shavings was found to give the best performance of demulsification. The demulsification efficiency can exceed 96.5% when demulsification conditions are optimized. The packed-column showed much better performance both in terms of demulsification efficiency and repeated use of the recovered oil phase for extracting cadmium in simulated wastewater. Operating variables governing the demulsification efficiency were investigated.
文摘Extraction behavior of chlorpromazine hydrochloride (CPZ) and procaine hydro- chloride (PCN) in the system described in the title was studied. Research shows that the extraction efficiency of CPZ can amount to 96% by twice extraction, while that of PCN is 77%. This system produces the distribution coefficients (KD) of 12.3 and 2.6 respectively for CPZ and PCN. Extraction mechanism is deduced according to ultraviolet and molecular fluorescence spectra variation of the drugs in the system studied.
文摘A spectrophotometric approach for the detection of non-ionic surfactant (Triton X-100) has been proposed in this paper. This method does not involve extraction of the ion-associate with harmful solvents, but employs adhesion of the ion-association of potassium/non-ionic surfactants complex and tetraphenylporphyrin tetrasulfonic acid obtained by vigorous shaking. The adhered ion-associate was dissolved with water and its absorbance was measured. The sensitivity for Triton X-100 was determined to be 0.146 (expressed as absorbance of 1 mg/L solution). The adhesion tendency of ion-associate was found to be dependent on the water contact angle, which in turn was influenced by a high adhesion of the ion-associate and by low blank values. In this respect, a tetrafluo-roethylene vessel was found to be the most suitable for the detection of non-ionic surfactants. This spectrophotometrical method is simply and rapidly performed by a procedure based on mechanical shaking and can be employed to detect non-ionic surfactants containing more than 7 polyethylene oxide units.
文摘The hydrophilic porous glass membranes were used to demulsify water in oil emulsion, liquid membrane and demulsification efficiency can reach more than 96 percent. Effects of pore size of the membrane, transmembrane pressure and volumetric ratio of oil phase to internal aqueous phase in the emulsion on demulsification were investigated. Correspondingly, effect of transmembrane pressure on permeation flux of the droplets was also studied.
基金Supported by the National Natural Science Foundation of China(No.29976021).
文摘A study on the membrane coalescence demulsification was carried out with four working systems of water/n-butyl alcohol, water/n-octanol, water/30% TBP(in kerosene) and water/kerosene. The membranes made of polytetrafluoroethylene (PTFE) with 1.0μm pore size were used. The results indicated that the excellent demulsification efficiency for emulsions with various oil contents was obtained. A conductivity probe was used to study the demulsification mechanism. An electrode probe was designed and used to determine the oil content near the membrane surface. The obtained data showed that the oil content in the permeated stream was much higher than that in the feed emulsion. A physical mechanism to explain the membrane demulsification was put forward.
基金Scientific Platform Project of the Ministry of Education(fykf201907)the Postdoctoral Science Foundation Project of the Natural Science Foundation of Chongqing Municipality(cstc2021jcyjbshX0194)+3 种基金Science and Technology Research Program of Chongqing Municipal Education Commission(KJQN202100820 and KJZD-K201900804)Science and Technology Innovation Project of the Construction of the Chengdu-Chongqing Economic Circle of Chongqing Municipal Education Commission(KJCX2020036)Scientific Research Project of Chongqing Technology and Business University(2152016 and 2056006)Chongqing Technical Innovation and Application Project(cstc2019jscx-msxmX0275).
文摘As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsification behavior,characteristics,and stages under BPEF were explored.It was discovered that BPEF drove SSO/W emulsion to move and form vortexes,during which the oil droplets aggregated and accumulated to generate an oil droplet layer(ODL).ODL subsequently transformed into a continuous oil layer(COL)leading to the demulsification and separation of SSO/W emulsion.The conversion rate of ODL to COL was defined and used to evaluate the demulsification process and reflect the coalescence ability and transformation efficiency of dispersed oil droplets into COL.Furthermore,the effects of BPEF voltage,frequency,duty cycle,ratio of pulse output time,and surfactant type and content on the demulsification performance were examined.The optimal values of BPEF parameters for demulsification operation were 400 V,25 Hz,50%,and 4:1.O/W emulsion containing anionic surfactant was apt to be demulsified by BPEF,nonionic surfactant took the second place and cationic surfactant was the most difficult.A high surfactant content was not conducive to the BPEF demulsification.This work is anticipated to provide useful guidance for oil/water separation and oil recovery from actual emulsified oily wastewater by BPEF.
文摘A simple and rapid method for the determination of polyethylene oxide-type non-ionic surfactants is reported herein. This method is based on the adhesion of calcium/non-ionic surfactant complexes with tetra phenyl porphine sulfonic acid （TPPS） to the wall of reaction vessel upon vigorous shaking. The ion-associate adhering to the inner wall of the vessel was dissolved with water after discarding the solution and spectrophotometrically assayed at 412 nm. From the standard curve for Triton X-100, the order of the sensitivity for different ions was as follows： Ca^2＋〉 K^＋〉 NH4^＋〉 Ba^2＋. The proposed method does not involve extraction of the ion-associated with harmful solvents and can be simply performed by combining a procedure based on hand shaking and the use of a spectrophotometer.
文摘An improved rotating microchannel(IRM) separator was further explored in the intensification for demulsification and separation process. Oil-in-water(O/W) emulsion system of 2-ethylhexyl phosphoric acid-2-ethylhexyl ester(P507)–water without emulsifier was employed to evaluate the performance of the new equipment. In this experiment, the influence on demulsification separation process was explored by changing the geometrical structure and channel height of the microchannel and combining the liquid–liquid two-phase flow pattern, and the correlation general graph between demulsification efficiency and dimensionless parameters was established. The total demulsification effect of the IRM and the separation capacity of the clear organic phase recovered from demulsification are significantly improved. In addition, the liquid–liquid two-phase flow pattern of the clear organic phase after demulsification and the remaining emulsion in the IRM are observed and recorded by high-speed photography. The separation ability of organic phase from the upper outlet can be significantly improved when the total demulsification rate of IRM is up to 90%. There are 3 types and 6 kinds of flow patterns observed. The results demonstrated that the suitable demulsification performance is obtained when the liquid–liquid two-phase inside the IRM is in a parallel pattern. Finally, the relation map between total demulsification efficiency and the universal flow is drawn, which provides a basis for the accurate control of the IRM device.
