The electro-optical payloads on mobile platforms generally suffer undesirable vibrations generated by maneuvers and turbulence.These vibrations are in six degrees of freedom and cause line-of-sight jitters,resulting i...The electro-optical payloads on mobile platforms generally suffer undesirable vibrations generated by maneuvers and turbulence.These vibrations are in six degrees of freedom and cause line-of-sight jitters,resulting in image blurring and loss of tracking accuracy.In this paper,a Hexapod Vibration Isolation System(HVIS)is proposed and optimized to solve this problem.The optimization aims to centralize and minimize the natural frequencies of HVIS,for expanding the vibration isolation bandwidth and improving the vibration isolation in the higher frequency band.Considering that the design space for HVIS is limited and interfered with the frames of the mobile platform,a non-collision algorithm is proposed and applied in the optimization to obtain the feasible optimal design.The optimization result shows that the natural frequency bandwidth has been reduced by 42.9%,and the maximum natural frequency is reduced by 30.2%.The prototypes of initial and optimal designs are manufactured and tested.Both simulated and experimental results demonstrate the validity of the optimization,and the optimal design provides a maximum of 15 dB more isolation in rotation direction than the initial design.展开更多
In recent years,there have been fewer missions to detect neutrons in low Earth orbits(LEO),and the data obtained have been extremely limited.Studying the distribution of the neutron energy spectrum in LEO satellites t...In recent years,there have been fewer missions to detect neutrons in low Earth orbits(LEO),and the data obtained have been extremely limited.Studying the distribution of the neutron energy spectrum in LEO satellites through detection can help solve three major scientific problems:the source of particles in the inner radiation belt,information on solar-accelerated particles,and the proportion of neutrons from different sources in near-Earth space.The detection efficiency and accuracy of neutrons are affected by charged and primary particles in the environment and secondary neutrons produced by the spacecraft itself,which has been a hot research topic.The neutron spectrometer developed in this study adopts two combinations of 15 silicon detectors in terms of detector type and arrangement,which are used for neutron detection via the nuclear reaction method and recoil proton method,respectively,in which a 27μm-thick^(6)LiF conversion layer is used for thermal neutron detection up to 0.4 eV and a 300μm-thick high-density polyethylene conversion layer is used for fast-neutron detection up to 14 MeV and below.The design of the detector set can also remove the influence of primary charged particles and secondary neutrons in the detection environment to a certain extent,thereby improving the accuracy of neutron detection.In this study,the neutron spectrometer hardware,firmware,software design,and basic performance of the front-end readout chip SKIROC2A were tested.The readout circuit of each channel baseline ADC code was less than 17;thus,the channel consistency was good.The RMS noise of the channel baseline was only 7.1 mV and exhibited good stability.The maximum number of events that could be processed per second is 75.The overall power consumption was 3 W,the weight was 792 g,and the volume was less than 1 dm^(3).Furthermore,the neutron spectrometer was tested for principle and detection efficiency using various neutron sources,such as ^(241)Am-Be neutron source,2.5 MeV neutron beam,and 14 MeV neutron beam,and the experiments were analyzed with corresponding simulations.The experimental data and simulation results were in good agreement and met the design requirements.The intrinsic detection efficiency of the probes used in the neutron spectrometer was 1.05%for 14 MeV fast neutrons.展开更多
A polarization-maintaining （PM） fiber Mach-Zehnder （MZ） interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer, all the ...A polarization-maintaining （PM） fiber Mach-Zehnder （MZ） interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer, all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here,we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.展开更多
Liquid crystals （LCs） and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopan...Liquid crystals （LCs） and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopant and monomer concentrations on the electro-optical properties, such as contrast ratio, driving voltage, hysteresis width and response time, are investigated. The reasons of electro-optical properties influenced by the concentrations of the materials are discussed. Through the proper material recipe, the electro-optical properties of polymer stabilized cholesteric LC film can be optimized.展开更多
The novel BaTiO3/BiFeO3/TiO2 multilayer heterojunction is prepared on a fluorine-doped tinoxide(FTO) substrate by the sol–gel method. The results indicate that the Pt/Ba TiO3/BiFeO3/TiO2/FTO heterojunction exhibits s...The novel BaTiO3/BiFeO3/TiO2 multilayer heterojunction is prepared on a fluorine-doped tinoxide(FTO) substrate by the sol–gel method. The results indicate that the Pt/Ba TiO3/BiFeO3/TiO2/FTO heterojunction exhibits stable bipolar resistive switching characteristic, good retention performance, and reversal characteristic. Under different pulse voltages and light fields, four stable resistance states can also be realized. The analysis shows that the main conduction mechanism of the resistive switching characteristic of the heterojunction is space charge limited current(SCLC) effect. After the comprehensive analysis of the band diagram and the P–E ferroelectric property of the multilayer heterojunction, we can deduce that the SCLC is formed by the effect of the oxygen vacancy which is controlled by ferroelectric polarizationmodulated change of interfacial barrier. And the effective photo-generated carrier also plays a regulatory role in resistance state(RS), which is formed by the double ferroelectric layer Ba TiO3/BiFeO3 under different light fields. This research is of potential application values for developing the multi-state non-volatile resistance random access memory(RRAM) devices based on ferroelectric materials.展开更多
We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd：YAG laser. We ex- perimentally study and compare the performance of the pulsed Nd：YAG laser in the free-running and Q-switch...We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd：YAG laser. We ex- perimentally study and compare the performance of the pulsed Nd：YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configu- ration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.展开更多
Transparent relaxor ferroelectric ceramics of the system lanthanum modified lead magnesium niobate have been investigated for a variety of electro-optic properties could make these materials alternatives to (Pb,La)(Zr...Transparent relaxor ferroelectric ceramics of the system lanthanum modified lead magnesium niobate have been investigated for a variety of electro-optic properties could make these materials alternatives to (Pb,La)(Zr,Ti)O3. However, a study that relates the properties in function stoichiometric formula, it has not been analyzed heretofore. Therefore, in this work the effect of A-site substitution of La+3 in the characterization microstructural, structural, optical and electro-optical on (1-x)[Pb(1-3/2y)Lay(Mg1/3Nb2/3)O3]-xPbTiO3 and (1-z)[(1-x)Pb(Mg1/3Nb2/3)O3+xPbTiO3]+zLa2O3 has been performed. It was observed that the properties according to the stoichiometric formula and the PT had a maximum whose behavior was related to the addition of lanthanum in each stoichiometries.展开更多
In this work, we studied the electro-optical properties of high-aligned carbon nanotubes deposited at room temperature. For this, we used the High Density Plasma Chemical Vapor Deposition system. This system uses a ne...In this work, we studied the electro-optical properties of high-aligned carbon nanotubes deposited at room temperature. For this, we used the High Density Plasma Chemical Vapor Deposition system. This system uses a new concept of plasma generation: a planar coil is coupled to an RF system for plasma generation. This was used together with an electrostatic shield, for plasma densification, thereby obtaining high-density plasmas. The carbon nanotubes were deposited using pure methane plasmas. Three methods were used for the surface modification of the sample: reference substrate (silicon wafer only submitted to a chemical cleaning), silicon wafer with surface roughness generated by plasma etching, silicon wafer with a thin iron film and silicon wafer with diamond nano powder used as precursor materials. For each kind of silicon wafer surface, the carbon nanotubes were deposited with two different deposition times (two and three hours). The carbon nanotubes structural characteristics were analyzed by Atomic Force Microscope and Scanning Electronic Microscope. The carbon nanotubes electrical characteristics were observed by Raman Spectroscopy and the carbon nanotubes electro-optical properties were analyzed by current vs voltage electrical measurements and photo-luminescence spectroscopy measurements. The photoelectric effect in the carbon nanotubes were determined by photo-induced current measurements. In this work, we obtained carbon nanotubes with semiconductor properties and carbon nanotubes with metallic properties. The electro-optical effects depend strongly on the substrate preparation and the deposition parameters of the carbon nanotubes. The carbon nanotubes are high aligned and show singular properties that can be used for many applications.展开更多
Liquid crystal（LC） compound with isothiocyanate and naphthyl group is an attractive high birefringence LC material,and can be used in optical devices. In this paper, the electro-optical properties of a series of thi...Liquid crystal（LC） compound with isothiocyanate and naphthyl group is an attractive high birefringence LC material,and can be used in optical devices. In this paper, the electro-optical properties of a series of this type of LC compounds were investigated. The melting points and enthalpy values of these LC compounds were higher than those of corresponding compounds with the phenyl group. These compounds exhibited high birefringence with a maximum value of 0.66. Fluorine substitution in the molecular almost does not affect the birefringence value. When these LC compounds with the naphthyl group were dissolved in a commercial LC mixture, the electro-optical properties depending on temperature were investigated. In the low-temperature region, LC mixtures with the naphthyl-group LC compounds exhibited higher viscosity than pure commercial LCs. In the high-temperature region, viscosity values very closely approached each other. When response performance was investigated, figure-of-merit（FoM） values were measured. The Fo M values of LC mixtures containing LC compounds with naphthyl group were lower than those of reference benzene LCs in the low-temperature region. However, in the high-temperature region, the results were reversed. These isothiocyanate LC compounds with naphthyl group can be applied in special fast-response LC device, particularly the ones used under high-temperature conditions.展开更多
Fluorinated smectic liquid crystals each with a biphenyl benzoate rigid core are investigated. Molecular structures of the studied compounds have difference only in fluorine position and the length of the carbon chain...Fluorinated smectic liquid crystals each with a biphenyl benzoate rigid core are investigated. Molecular structures of the studied compounds have difference only in fluorine position and the length of the carbon chain. Dielectric relaxation study and electro-optical measurements are carried out with the classical SSFLC geometry. The field-induced phase transitions are studied and the（E,T） phase diagram is established.展开更多
A bunch arrival-time monitor(BAM) based on an electro-optical intensity modulation scheme is currently under development at Shanghai Soft X-ray Free-Electron Laser to meet the high-resolution requirements for bunch st...A bunch arrival-time monitor(BAM) based on an electro-optical intensity modulation scheme is currently under development at Shanghai Soft X-ray Free-Electron Laser to meet the high-resolution requirements for bunch stability. The BAM uses a radio frequency signal generated by a pickup cavity to modulate the reference laser pulses in an electro-optical intensity modulator(EOM), and the bunch arrival-time information is derived from the amplitude change of the laser pulse after laser pulse modulation.EOM is a key optical component in the BAM system.Through the basic principle analysis of BAM, many parameters of the EOM are observed to affect the measurement resolution of the BAM system. Therefore, a systematic analysis of the EOM is crucial. In this paper, we present two schemes to compare and analyze an EOM and provide a reference for selecting a new version of the EOM.展开更多
The liquid crystal composite materials consist of microdroplets of liquid crystals which are spontaneously formed in a matrix of a polymer at the time of its polymerization. The director configuration in liquid crysta...The liquid crystal composite materials consist of microdroplets of liquid crystals which are spontaneously formed in a matrix of a polymer at the time of its polymerization. The director configuration in liquid crystal droplets, the model of orientation of droplets, and the contrast ratios of a cell are investigated. Droplet size, spacing and distribution are readily controlled in these materials to allow optimization of displays based upon electrically controlled light scattering from the liquid crystal droplets. Preliminary experimental and theoretical studies of the light scattering and electro-optic response of new material show that these materials can offer new features suitable for large area displays and light valves.展开更多
Electro-Optic Sampling(EOS)detection technique has been widely used in terahertz science and tech⁃nology,and it also can measure the field time waveform of the few-cycle laser pulse.Its frequency response and band lim...Electro-Optic Sampling(EOS)detection technique has been widely used in terahertz science and tech⁃nology,and it also can measure the field time waveform of the few-cycle laser pulse.Its frequency response and band limitation are determined directly by the electro-optic crystal and duration of the probe laser pulse.Here,we investigate the performance of the EOS with thin GaSe crystal in the measurement of the mid-infrared few-cycle la⁃ser pulse.The shift of the central frequency and change of the bandwidth induced by the EOS detection are calcu⁃lated,and then the pulse distortions induced in this detection process are discussed.It is found that this technique produces a red-shift of the central frequency and narrowing of the bandwidth.These changings decrease when the laser wavelength increases from 2μm to 10μm.This work can help to estimate the performance of the EOS de⁃tection technique in the mid-infrared band and offer a reference for the related experiment as well.展开更多
The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precisio...The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precision.To ensure its accuracy of detection,it is necessary to correlate their thermal models to in-orbit da⁃ta.In this work,an investigation of intelligent correlation method named Intelligent Correlation Platform for Ther⁃mal Model(ICP-TM)was established,the advanced Kriging surrogate model and efficient adaptive region opti⁃mization algorithm were introduced.After the correlation with this method for FY-3E/HIRAS-Ⅱ,the results indi⁃cate that compared with the data in orbit,the error of the thermal model has decreased from 5 K to within±1 K in cold case(10℃).Then,the correlated model is validated in hot case(20℃),and the correlated model exhibits good universality.This correlation precision is also much superiors to the general ones like 3 K in other similar lit⁃erature.Furthermore,the process is finished in 8 days using ICP-TM,the efficiency is much better than 3 months based on manual.The results show that the proposed approach significantly enhances the accuracy and efficiency of thermal model,this contributes to the precise thermal control of subsequent infrared optical payloads.展开更多
The rocket sled system is not only a high-speed dynamic ground test system,but also one of the future aerospace horizontal launch schemes.The winged load,as a common type of payload,has greater vibration and noise int...The rocket sled system is not only a high-speed dynamic ground test system,but also one of the future aerospace horizontal launch schemes.The winged load,as a common type of payload,has greater vibration and noise intensity than the wingless load.Due to the severe aerodynamic instability prior to separation,the head-up or head-down phenomena are more evident and the test accuracy significantly decreases.The high-precision computer fluid dynamics and aeroacoustic analysis are employed to explore the multifield coupling mechanism of a rocket sled with the winged payload in the wide speed range(Ma=0.5–2).The results show that as the incoming velocity increases,the cone angle of the shock wave of the rocket sled decreases,the shock pressure increases quickly,and the vortex between the slippers splits and gradually shrinks in size.The velocity of the rocket sled exerts little influence on the modal resonance frequency.The wing has a significant impact on aerodynamic noise,and as the sound pressure level rises,the propagation direction gradually shifts towards the rear and upper regions of the wing.展开更多
本文介绍了红外感知技术在“向上看”的深空探测与“向下看”的对地观测两大领域的发展脉络和前沿挑战。在深空探测方面,以詹姆斯·韦布空间望远镜(James Webb Space Telescope, JWST)为代表,该技术正通过超大口径、甚长波段和超低...本文介绍了红外感知技术在“向上看”的深空探测与“向下看”的对地观测两大领域的发展脉络和前沿挑战。在深空探测方面,以詹姆斯·韦布空间望远镜(James Webb Space Telescope, JWST)为代表,该技术正通过超大口径、甚长波段和超低温制冷等手段,不断逼近观测的物理极限,并致力于揭示宇宙早期的历史奥秘。阐述了对地观测领域不同时期搭载于各类卫星的红外探测载荷的主要发展过程及其代表性和特色。红外对地观测技术从过去宽幅下的低空间分辨率和少量波段,向着空谱大范围下的时-空-谱-辐分辨率提升迈进。大口径低背景光学、长波长高灵敏度探测器、片上智能感知、大数据孪生系统等新型技术,以及通导遥一体的“即时遥感”和商业航天的大规模发展,将助力构建“红外数字地球”底座,增强人类对地球多圈层异常事件以及各种复杂循环过程演变的实时认知和精准预测,推动红外对地观测技术走向大众化应用。展开更多
基于Web of Science核心合集数据库,采用文献计量学方法对中国探月工程(2003-2024)的科研产出进行系统分析.通过量化评估1023篇SCI论文的时空分布特征、国际合作态势及学术影响力,揭示了中国探月工程对全球月球科学研究的贡献.研究表明...基于Web of Science核心合集数据库,采用文献计量学方法对中国探月工程(2003-2024)的科研产出进行系统分析.通过量化评估1023篇SCI论文的时空分布特征、国际合作态势及学术影响力,揭示了中国探月工程对全球月球科学研究的贡献.研究表明,中国探月工程的实施使中国月球科学领域发文量占比提升至32.6%(2024年),工程产出论文的CNCI值(1.03)超越全球均值;科研突破集中于嫦娥四号(月球背面着陆巡视探测)与嫦娥五号(月球样品分析)任务,产出181篇高影响力论文;国际引用情况中,非中国机构占比显著增长,显示工程成果获得广泛国际认可.研究成果为评估中国深空探测计划的科学效益提供了定量依据.展开更多
The fluorine-containing organic polymer was synthesized from 3, 3＇, 4, 4＇-Bisphenyltetracarboxylic （BPDA）, and 2,2-Bis （3-amino-4-hydroxyyphenyl） hexafluoropropane （6FHP）. It is a first-step preparation of a p...The fluorine-containing organic polymer was synthesized from 3, 3＇, 4, 4＇-Bisphenyltetracarboxylic （BPDA）, and 2,2-Bis （3-amino-4-hydroxyyphenyl） hexafluoropropane （6FHP）. It is a first-step preparation of a preimided hydroxy-containing polyimide, followed by the covalent bonding of an active chromophore, dispersed red 19 （DR19）, onto the backbone of the polyimide via the Mitsunobu reaction. The nonlinear optical （NLO） containing polyimide was synthesized. The differential scanning calorimeter （DSC）and thermal gravimetric analysis （TGA） exhibited Tg and the temperature Tg at which 5 % mass losses occurring of polymer were 248 and 309 ℃, respectively. A reflective electro-optic （EO） modulator using this polymer was fabricated. The optical nonlinearities were determined to be d33 = 5. 209×10^-9 esu （poling voltage of 3.6 kV, 205 ℃） and d33 =7. 418×10^-9esu （poling voltage of 3. 8 kV, 210 ℃） by the second harmonic generation method in in-situ condition at a fundamental wavelength of 1 064 nm. The EO coefficients 733 of the polymer layer in the EO modulator were determined to be 2. 182 pm/V （poling voltage of 3.6 kV, 205 ℃） and 3. 107 pm/V （poling voltage of 3.8 kV, 210 ℃） at 1064 nm by an attenuated-total-reflection （ATR） method.展开更多
We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded...We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.展开更多
基金supported by the National Key R&D Program of China(No.2021YFA1003503)。
文摘The electro-optical payloads on mobile platforms generally suffer undesirable vibrations generated by maneuvers and turbulence.These vibrations are in six degrees of freedom and cause line-of-sight jitters,resulting in image blurring and loss of tracking accuracy.In this paper,a Hexapod Vibration Isolation System(HVIS)is proposed and optimized to solve this problem.The optimization aims to centralize and minimize the natural frequencies of HVIS,for expanding the vibration isolation bandwidth and improving the vibration isolation in the higher frequency band.Considering that the design space for HVIS is limited and interfered with the frames of the mobile platform,a non-collision algorithm is proposed and applied in the optimization to obtain the feasible optimal design.The optimization result shows that the natural frequency bandwidth has been reduced by 42.9%,and the maximum natural frequency is reduced by 30.2%.The prototypes of initial and optimal designs are manufactured and tested.Both simulated and experimental results demonstrate the validity of the optimization,and the optimal design provides a maximum of 15 dB more isolation in rotation direction than the initial design.
基金supported by the National Natural Science Foundation of China(NSFC)(Nos.42225405 and U2106202)。
文摘In recent years,there have been fewer missions to detect neutrons in low Earth orbits(LEO),and the data obtained have been extremely limited.Studying the distribution of the neutron energy spectrum in LEO satellites through detection can help solve three major scientific problems:the source of particles in the inner radiation belt,information on solar-accelerated particles,and the proportion of neutrons from different sources in near-Earth space.The detection efficiency and accuracy of neutrons are affected by charged and primary particles in the environment and secondary neutrons produced by the spacecraft itself,which has been a hot research topic.The neutron spectrometer developed in this study adopts two combinations of 15 silicon detectors in terms of detector type and arrangement,which are used for neutron detection via the nuclear reaction method and recoil proton method,respectively,in which a 27μm-thick^(6)LiF conversion layer is used for thermal neutron detection up to 0.4 eV and a 300μm-thick high-density polyethylene conversion layer is used for fast-neutron detection up to 14 MeV and below.The design of the detector set can also remove the influence of primary charged particles and secondary neutrons in the detection environment to a certain extent,thereby improving the accuracy of neutron detection.In this study,the neutron spectrometer hardware,firmware,software design,and basic performance of the front-end readout chip SKIROC2A were tested.The readout circuit of each channel baseline ADC code was less than 17;thus,the channel consistency was good.The RMS noise of the channel baseline was only 7.1 mV and exhibited good stability.The maximum number of events that could be processed per second is 75.The overall power consumption was 3 W,the weight was 792 g,and the volume was less than 1 dm^(3).Furthermore,the neutron spectrometer was tested for principle and detection efficiency using various neutron sources,such as ^(241)Am-Be neutron source,2.5 MeV neutron beam,and 14 MeV neutron beam,and the experiments were analyzed with corresponding simulations.The experimental data and simulation results were in good agreement and met the design requirements.The intrinsic detection efficiency of the probes used in the neutron spectrometer was 1.05%for 14 MeV fast neutrons.
文摘A polarization-maintaining （PM） fiber Mach-Zehnder （MZ） interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer, all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here,we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.
基金Project partially supported by the National Natural Science Foundation of China （Grant Nos. 60736042, 60578035 and 50703039） and the Science Foundation of Jilin Province of China （Grant Nos. 20050520 and 20050321-2）.
文摘Liquid crystals （LCs） and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopant and monomer concentrations on the electro-optical properties, such as contrast ratio, driving voltage, hysteresis width and response time, are investigated. The reasons of electro-optical properties influenced by the concentrations of the materials are discussed. Through the proper material recipe, the electro-optical properties of polymer stabilized cholesteric LC film can be optimized.
基金Project supported by the Scientific Research Program of Hunan Provincial Education Department,China(Grant No.18C0232)the International Cooperative Extension Program of Changsha University of Science and Technology,China(Grant No.2019IC35)
文摘The novel BaTiO3/BiFeO3/TiO2 multilayer heterojunction is prepared on a fluorine-doped tinoxide(FTO) substrate by the sol–gel method. The results indicate that the Pt/Ba TiO3/BiFeO3/TiO2/FTO heterojunction exhibits stable bipolar resistive switching characteristic, good retention performance, and reversal characteristic. Under different pulse voltages and light fields, four stable resistance states can also be realized. The analysis shows that the main conduction mechanism of the resistive switching characteristic of the heterojunction is space charge limited current(SCLC) effect. After the comprehensive analysis of the band diagram and the P–E ferroelectric property of the multilayer heterojunction, we can deduce that the SCLC is formed by the effect of the oxygen vacancy which is controlled by ferroelectric polarizationmodulated change of interfacial barrier. And the effective photo-generated carrier also plays a regulatory role in resistance state(RS), which is formed by the double ferroelectric layer Ba TiO3/BiFeO3 under different light fields. This research is of potential application values for developing the multi-state non-volatile resistance random access memory(RRAM) devices based on ferroelectric materials.
文摘We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd：YAG laser. We ex- perimentally study and compare the performance of the pulsed Nd：YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configu- ration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.
基金CAPES,FAPESP and CNPq for the financial support.
文摘Transparent relaxor ferroelectric ceramics of the system lanthanum modified lead magnesium niobate have been investigated for a variety of electro-optic properties could make these materials alternatives to (Pb,La)(Zr,Ti)O3. However, a study that relates the properties in function stoichiometric formula, it has not been analyzed heretofore. Therefore, in this work the effect of A-site substitution of La+3 in the characterization microstructural, structural, optical and electro-optical on (1-x)[Pb(1-3/2y)Lay(Mg1/3Nb2/3)O3]-xPbTiO3 and (1-z)[(1-x)Pb(Mg1/3Nb2/3)O3+xPbTiO3]+zLa2O3 has been performed. It was observed that the properties according to the stoichiometric formula and the PT had a maximum whose behavior was related to the addition of lanthanum in each stoichiometries.
文摘In this work, we studied the electro-optical properties of high-aligned carbon nanotubes deposited at room temperature. For this, we used the High Density Plasma Chemical Vapor Deposition system. This system uses a new concept of plasma generation: a planar coil is coupled to an RF system for plasma generation. This was used together with an electrostatic shield, for plasma densification, thereby obtaining high-density plasmas. The carbon nanotubes were deposited using pure methane plasmas. Three methods were used for the surface modification of the sample: reference substrate (silicon wafer only submitted to a chemical cleaning), silicon wafer with surface roughness generated by plasma etching, silicon wafer with a thin iron film and silicon wafer with diamond nano powder used as precursor materials. For each kind of silicon wafer surface, the carbon nanotubes were deposited with two different deposition times (two and three hours). The carbon nanotubes structural characteristics were analyzed by Atomic Force Microscope and Scanning Electronic Microscope. The carbon nanotubes electrical characteristics were observed by Raman Spectroscopy and the carbon nanotubes electro-optical properties were analyzed by current vs voltage electrical measurements and photo-luminescence spectroscopy measurements. The photoelectric effect in the carbon nanotubes were determined by photo-induced current measurements. In this work, we obtained carbon nanotubes with semiconductor properties and carbon nanotubes with metallic properties. The electro-optical effects depend strongly on the substrate preparation and the deposition parameters of the carbon nanotubes. The carbon nanotubes are high aligned and show singular properties that can be used for many applications.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61378075,61377032,11604327,and 61475152)the Science Foundation of State Key Laboratory of Applied Optics,China
文摘Liquid crystal（LC） compound with isothiocyanate and naphthyl group is an attractive high birefringence LC material,and can be used in optical devices. In this paper, the electro-optical properties of a series of this type of LC compounds were investigated. The melting points and enthalpy values of these LC compounds were higher than those of corresponding compounds with the phenyl group. These compounds exhibited high birefringence with a maximum value of 0.66. Fluorine substitution in the molecular almost does not affect the birefringence value. When these LC compounds with the naphthyl group were dissolved in a commercial LC mixture, the electro-optical properties depending on temperature were investigated. In the low-temperature region, LC mixtures with the naphthyl-group LC compounds exhibited higher viscosity than pure commercial LCs. In the high-temperature region, viscosity values very closely approached each other. When response performance was investigated, figure-of-merit（FoM） values were measured. The Fo M values of LC mixtures containing LC compounds with naphthyl group were lower than those of reference benzene LCs in the low-temperature region. However, in the high-temperature region, the results were reversed. These isothiocyanate LC compounds with naphthyl group can be applied in special fast-response LC device, particularly the ones used under high-temperature conditions.
文摘Fluorinated smectic liquid crystals each with a biphenyl benzoate rigid core are investigated. Molecular structures of the studied compounds have difference only in fluorine position and the length of the carbon chain. Dielectric relaxation study and electro-optical measurements are carried out with the classical SSFLC geometry. The field-induced phase transitions are studied and the（E,T） phase diagram is established.
基金supported by the National Key R&D Plan(No.2016YFA0401900)
文摘A bunch arrival-time monitor(BAM) based on an electro-optical intensity modulation scheme is currently under development at Shanghai Soft X-ray Free-Electron Laser to meet the high-resolution requirements for bunch stability. The BAM uses a radio frequency signal generated by a pickup cavity to modulate the reference laser pulses in an electro-optical intensity modulator(EOM), and the bunch arrival-time information is derived from the amplitude change of the laser pulse after laser pulse modulation.EOM is a key optical component in the BAM system.Through the basic principle analysis of BAM, many parameters of the EOM are observed to affect the measurement resolution of the BAM system. Therefore, a systematic analysis of the EOM is crucial. In this paper, we present two schemes to compare and analyze an EOM and provide a reference for selecting a new version of the EOM.
文摘The liquid crystal composite materials consist of microdroplets of liquid crystals which are spontaneously formed in a matrix of a polymer at the time of its polymerization. The director configuration in liquid crystal droplets, the model of orientation of droplets, and the contrast ratios of a cell are investigated. Droplet size, spacing and distribution are readily controlled in these materials to allow optimization of displays based upon electrically controlled light scattering from the liquid crystal droplets. Preliminary experimental and theoretical studies of the light scattering and electro-optic response of new material show that these materials can offer new features suitable for large area displays and light valves.
基金Supported by the National Natural Science Foundation of China(12064028)Jiangxi Provincial Natural Science Foundation(20232BAB201045).
文摘Electro-Optic Sampling(EOS)detection technique has been widely used in terahertz science and tech⁃nology,and it also can measure the field time waveform of the few-cycle laser pulse.Its frequency response and band limitation are determined directly by the electro-optic crystal and duration of the probe laser pulse.Here,we investigate the performance of the EOS with thin GaSe crystal in the measurement of the mid-infrared few-cycle la⁃ser pulse.The shift of the central frequency and change of the bandwidth induced by the EOS detection are calcu⁃lated,and then the pulse distortions induced in this detection process are discussed.It is found that this technique produces a red-shift of the central frequency and narrowing of the bandwidth.These changings decrease when the laser wavelength increases from 2μm to 10μm.This work can help to estimate the performance of the EOS de⁃tection technique in the mid-infrared band and offer a reference for the related experiment as well.
基金Supported by the National Key Research and Development Program of China(2022YFB3904803)。
文摘The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precision.To ensure its accuracy of detection,it is necessary to correlate their thermal models to in-orbit da⁃ta.In this work,an investigation of intelligent correlation method named Intelligent Correlation Platform for Ther⁃mal Model(ICP-TM)was established,the advanced Kriging surrogate model and efficient adaptive region opti⁃mization algorithm were introduced.After the correlation with this method for FY-3E/HIRAS-Ⅱ,the results indi⁃cate that compared with the data in orbit,the error of the thermal model has decreased from 5 K to within±1 K in cold case(10℃).Then,the correlated model is validated in hot case(20℃),and the correlated model exhibits good universality.This correlation precision is also much superiors to the general ones like 3 K in other similar lit⁃erature.Furthermore,the process is finished in 8 days using ICP-TM,the efficiency is much better than 3 months based on manual.The results show that the proposed approach significantly enhances the accuracy and efficiency of thermal model,this contributes to the precise thermal control of subsequent infrared optical payloads.
基金supported by the National Natural Science Foundation of China(No.12104047)。
文摘The rocket sled system is not only a high-speed dynamic ground test system,but also one of the future aerospace horizontal launch schemes.The winged load,as a common type of payload,has greater vibration and noise intensity than the wingless load.Due to the severe aerodynamic instability prior to separation,the head-up or head-down phenomena are more evident and the test accuracy significantly decreases.The high-precision computer fluid dynamics and aeroacoustic analysis are employed to explore the multifield coupling mechanism of a rocket sled with the winged payload in the wide speed range(Ma=0.5–2).The results show that as the incoming velocity increases,the cone angle of the shock wave of the rocket sled decreases,the shock pressure increases quickly,and the vortex between the slippers splits and gradually shrinks in size.The velocity of the rocket sled exerts little influence on the modal resonance frequency.The wing has a significant impact on aerodynamic noise,and as the sound pressure level rises,the propagation direction gradually shifts towards the rear and upper regions of the wing.
文摘本文介绍了红外感知技术在“向上看”的深空探测与“向下看”的对地观测两大领域的发展脉络和前沿挑战。在深空探测方面,以詹姆斯·韦布空间望远镜(James Webb Space Telescope, JWST)为代表,该技术正通过超大口径、甚长波段和超低温制冷等手段,不断逼近观测的物理极限,并致力于揭示宇宙早期的历史奥秘。阐述了对地观测领域不同时期搭载于各类卫星的红外探测载荷的主要发展过程及其代表性和特色。红外对地观测技术从过去宽幅下的低空间分辨率和少量波段,向着空谱大范围下的时-空-谱-辐分辨率提升迈进。大口径低背景光学、长波长高灵敏度探测器、片上智能感知、大数据孪生系统等新型技术,以及通导遥一体的“即时遥感”和商业航天的大规模发展,将助力构建“红外数字地球”底座,增强人类对地球多圈层异常事件以及各种复杂循环过程演变的实时认知和精准预测,推动红外对地观测技术走向大众化应用。
文摘基于Web of Science核心合集数据库,采用文献计量学方法对中国探月工程(2003-2024)的科研产出进行系统分析.通过量化评估1023篇SCI论文的时空分布特征、国际合作态势及学术影响力,揭示了中国探月工程对全球月球科学研究的贡献.研究表明,中国探月工程的实施使中国月球科学领域发文量占比提升至32.6%(2024年),工程产出论文的CNCI值(1.03)超越全球均值;科研突破集中于嫦娥四号(月球背面着陆巡视探测)与嫦娥五号(月球样品分析)任务,产出181篇高影响力论文;国际引用情况中,非中国机构占比显著增长,显示工程成果获得广泛国际认可.研究成果为评估中国深空探测计划的科学效益提供了定量依据.
基金Jiangsu Planned Projects for Postdoctoral ResearchFunds(No0602037B)the Natural Science Foundation of Higher Edu-cation Institutions of Jiangsu Province (No05KJB150016)+1 种基金the Nation-al Natural Science Foundation of China (No50377005)the Fund ofJiangsu University (No06JDG015)
文摘The fluorine-containing organic polymer was synthesized from 3, 3＇, 4, 4＇-Bisphenyltetracarboxylic （BPDA）, and 2,2-Bis （3-amino-4-hydroxyyphenyl） hexafluoropropane （6FHP）. It is a first-step preparation of a preimided hydroxy-containing polyimide, followed by the covalent bonding of an active chromophore, dispersed red 19 （DR19）, onto the backbone of the polyimide via the Mitsunobu reaction. The nonlinear optical （NLO） containing polyimide was synthesized. The differential scanning calorimeter （DSC）and thermal gravimetric analysis （TGA） exhibited Tg and the temperature Tg at which 5 % mass losses occurring of polymer were 248 and 309 ℃, respectively. A reflective electro-optic （EO） modulator using this polymer was fabricated. The optical nonlinearities were determined to be d33 = 5. 209×10^-9 esu （poling voltage of 3.6 kV, 205 ℃） and d33 =7. 418×10^-9esu （poling voltage of 3. 8 kV, 210 ℃） by the second harmonic generation method in in-situ condition at a fundamental wavelength of 1 064 nm. The EO coefficients 733 of the polymer layer in the EO modulator were determined to be 2. 182 pm/V （poling voltage of 3.6 kV, 205 ℃） and 3. 107 pm/V （poling voltage of 3.8 kV, 210 ℃） at 1064 nm by an attenuated-total-reflection （ATR） method.
文摘We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.
