The organic phase extracted from interfacial crud of copper solvent extraction at Dexing Copper Mine was analyzed for its different components by combined gas chromatography mass spectroscopy. It was found that the ma...The organic phase extracted from interfacial crud of copper solvent extraction at Dexing Copper Mine was analyzed for its different components by combined gas chromatography mass spectroscopy. It was found that the main impurities in organic phase were methylnaphthalenes and di methylnaphthalenes which originated from commercial 260# kerosene used as diluent. It was found that the impurities containing diluent was unfavorable to phase disengagement. Methods were suggested to improve diluent properties to prevent stable interfacial emulsion.展开更多
The enrichment of copper from copper–cyanide wastewater by solvent extraction was investigated using a quaternary ammonium salt as an extractant. The influences of important parameters, e.g., organic-phase components...The enrichment of copper from copper–cyanide wastewater by solvent extraction was investigated using a quaternary ammonium salt as an extractant. The influences of important parameters, e.g., organic-phase components, aqueous pH values, temperature, inorganic anion impurities, CN/Cu molar ratio, and stripping reagents, were examined systematically, and the optimal conditions were determined. The results indicated that copper was effectively concentrated from low-concentration solutions using Aliquat 336 and that the extraction efficiency increased linearly with increasing temperature. The aqueous pH value and concentrations of inorganic anion impurities only weakly affected the extraction process when varied in appropriate ranges. The CN/Cu molar ratio affected the extraction efficiency by changing the distribution of copper–cyanide complexes. The difference in gold leaching efficiency between using raffinate and fresh water was negligible.展开更多
Copper-catalyzed synthesis of N-aryl anthranilic acid derivatives using effective amination of 2-chloro and 2-bromobenzoic acid under microwave irradiation is reported. Some of the advantages of this method are high c...Copper-catalyzed synthesis of N-aryl anthranilic acid derivatives using effective amination of 2-chloro and 2-bromobenzoic acid under microwave irradiation is reported. Some of the advantages of this method are high chemoselectivity, short reaction times, ease of work up procedure and elimination of the need for acid protection. 2009 Published by Elsevier B.V. on behalf of Chinese Chemical Society.展开更多
Separation of copper and nickel by liquid-liquid extraction from aqueous solutions was studied using LIX 664N in kerosene as solvent. Both metals were taken in their sulfate form and ratio of copper to nickel in feed ...Separation of copper and nickel by liquid-liquid extraction from aqueous solutions was studied using LIX 664N in kerosene as solvent. Both metals were taken in their sulfate form and ratio of copper to nickel in feed solutions was maintained as 10:1. LIX 664N concentration in kerosene was varied from 10% to 40% (v/v) and its effect was studied on percent extraction of copper and nickel for organic to aqueous (O:A) phase ratio of 2:1 at pH 2. Experimental results showed that at pH 2, copper was selectively extracted from its mixture with nickel. Selectivity for copper extraction was as high as 6000 with 40% LIX 664N. Calculations using extraction isotherm indicate almost complete recovery of copper in two stages with O:A ratio of 1:1 and in one stage with O:A ratio of 2:1. After extraction of copper, the pH of raffinate containing nickel was adjusted to a value of 9 by addition of ammonia solution. The effect of LIX 664N concentration on extraction of nickel was studied. Up to 80% nickel could be extracted with 30% LIX 664N at O:A phase ratio of 2:1. Stripping of copper from the organic phase with 180 g/l sulfuric acid at O:A phase ratio of 1:1 gave 98.5% copper recovery in a two-stage operation.展开更多
Nickel, cobalt and copper were separated by solvent extraction with P204. The experimental results show that [Co(NH 3) 6] 3+ is an inert complex in extraction kinetics, therefore cobalt can be separated from nickel an...Nickel, cobalt and copper were separated by solvent extraction with P204. The experimental results show that [Co(NH 3) 6] 3+ is an inert complex in extraction kinetics, therefore cobalt can be separated from nickel and copper by non equilibrium solvent extraction. Under the conditions of temperature 25?℃, contact time of two phases 10?min, phase ratio 1∶1, aqueous pH 10.10 and concentration of P204 20%, [Co(NH 3) 6] 3+ is hardly extracted by P204, while the percentage extractions of nickel and copper are 79.3% and 93.9% respectively. Nickel and copper are separated by equilibrium solvent extraction with P204. Under the conditions of temperature 25?℃, contact time of two phases 1?min, phase ratio 1∶1, equilibrium pH 4.01 and concentration of P204 20%, the separation factor of copper and nickel is 216.展开更多
This paper describes a very simple, efficient synthesis of quinazolinones and chromeno[d]pyrimidinones from the reaction of aryl aldehydes, urea/thiourea and active methylene compounds（dimedone/4-hydroxycoumarin） us...This paper describes a very simple, efficient synthesis of quinazolinones and chromeno[d]pyrimidinones from the reaction of aryl aldehydes, urea/thiourea and active methylene compounds（dimedone/4-hydroxycoumarin） using nano-sized CuI particles under solvent-free conditions. The highlights of this new method are based on using an effective and recyclable catalyst, affording high yields of products,mild reaction conditions, facile work-up and purification.展开更多
The effects of the concentration of Lix 984N,phase ratio,initial pH value of aqueous phase and extraction time on the extraction of copper and iron under the condition of low Cu2+ /Fe3+ ratio in dump bioleaching solut...The effects of the concentration of Lix 984N,phase ratio,initial pH value of aqueous phase and extraction time on the extraction of copper and iron under the condition of low Cu2+ /Fe3+ ratio in dump bioleaching solution of Dexing Copper Mine were explored.The optimal conditions of extraction are as follows: the concentration of Lix 984N 10%; the phase ratio (O/A) 1:1; the initial pH value of aqueous phase 1.5 and the mixing time 2 min.The stripping experiments show that H2SO4 solution could efficiently recover copper from the organic phase under the optimal conditions.展开更多
Lix984N is intimately related to the dynamic characteristics of phase disengagement in copper solvent extraction because of its interfacial activity. With increasing Lix984N content, the phase disengagement time is pr...Lix984N is intimately related to the dynamic characteristics of phase disengagement in copper solvent extraction because of its interfacial activity. With increasing Lix984N content, the phase disengagement time is prolonged and the mechanism dominating phase disengagement process transfers from sedimentation to coalescence. The rate of droplet coalescence is faster than that of droplet sedimentation in the dense dispersion band when the volume fraction of Lix984N is less than 3.0%. The former almost equaled to the latter at Lix984N content of 3.0% and finally becomes lower than the latter when the volume fraction of Lix984N is more than 3.0%. The relationship between the adhesion force of two equal droplets and physical properties of fluids is deduced, which explains that the change of physical properties of organic phase with Lix984N content can make droplet coalescence more difficult and phase disengagement slower.展开更多
An experimental investigation was presented on the separation of Cu（Ⅱ）, Zn（Ⅱ）, and Cd（Ⅱ） from a rich sulfate leachate of zinc slag by solvent extraction. The results of orthogonal experiments indicate that LI...An experimental investigation was presented on the separation of Cu（Ⅱ）, Zn（Ⅱ）, and Cd（Ⅱ） from a rich sulfate leachate of zinc slag by solvent extraction. The results of orthogonal experiments indicate that LIX 984N is highly selective and very efficient in the extraction of Cu（Ⅱ）, and the analysis of variance indicates that the sequence of parameters according to their influence on the separation efficiency is phase ratio 〉 LIX 984N concentration 〉 pH value 〉 extraction time. The optimal condition for copper extraction is obtained as 25% of LIX 984N concentration, 7 rain of extraction time, 3：2 of phase ratio O/A, and pH = 1.7. The separation of Zn（Ⅱ） and Cd（Ⅱ） was performed after the copper extraction from the raffinate. Comparative analysis of the separation with di-2-ethylhexyl phosphoric acid （D2EHPA）, D2EHPA-tributyl- phosophate （TBP） synergistic extracting system, and 2-ethylhexyl phosphonic acid mono 2-ethylhexyl ester （HEHEHP） was made at pH = 2.0. It is demonstrated that the extraction efficiency with D2EHPA is improved after being saponified by sodium hydroxide, and D2EHPA-TBP synergistic extracting, as well as HEHEHP, has a superior selectivity to Zn（Ⅱ） over Cd（Ⅱ）.展开更多
A series of oil products taken from oil refining factories were used as diluents for copper extraction. The influence of diluents on extraction properties has been investigated. The extractants used are Lix984(He...A series of oil products taken from oil refining factories were used as diluents for copper extraction. The influence of diluents on extraction properties has been investigated. The extractants used are Lix984(Henkel) and M5640(Zeneca), and the adaptability of this diluents to these extractants is compared. The checked extraction properties include loading capacity, extraction and strip kinetics, copper/iron selectivity and phase disengagement. The results showed that DSR3 is a suitable diluent for M5640 and Lix984. Further research has been done to reduce the cost of this product by omitting several steps from its production process.展开更多
Extraction of copper from bacterial leach solution using Lix984 had been performed. It was found that the main factors influencing extraction yield of copper are the phase ratio and the concentration of extractant, fo...Extraction of copper from bacterial leach solution using Lix984 had been performed. It was found that the main factors influencing extraction yield of copper are the phase ratio and the concentration of extractant, following the pH of solution and extraction time and the order of factors influencing the separation rate is the pH of solution, the concentration of extractant, the extraction time and the phase ratio. The best conditions obtained by the orthogonal tests are as follows: the extractant concentration 4%, extraction time 3 min, phase ratio 1∶1, pH of solution 2.展开更多
研究了N902/煤油从氨/氯化铵水溶液中萃取铜.考察了萃取时间、水相pH值、萃取剂浓度、温度等对萃取率的影响,以及酸度和时间对铜的反萃率的影响.实验发现,在研究的条件下萃取5 m in达到平衡,而反萃则需要15 m in达到平衡.萃取过程是吸...研究了N902/煤油从氨/氯化铵水溶液中萃取铜.考察了萃取时间、水相pH值、萃取剂浓度、温度等对萃取率的影响,以及酸度和时间对铜的反萃率的影响.实验发现,在研究的条件下萃取5 m in达到平衡,而反萃则需要15 m in达到平衡.萃取过程是吸热过程,测得△H=4.0 kJ/mol.在实验范围内,萃取率先随pH值增大而增加,当pH值超过10.2后,随着pH值增大反而降低.展开更多
文摘The organic phase extracted from interfacial crud of copper solvent extraction at Dexing Copper Mine was analyzed for its different components by combined gas chromatography mass spectroscopy. It was found that the main impurities in organic phase were methylnaphthalenes and di methylnaphthalenes which originated from commercial 260# kerosene used as diluent. It was found that the impurities containing diluent was unfavorable to phase disengagement. Methods were suggested to improve diluent properties to prevent stable interfacial emulsion.
文摘The enrichment of copper from copper–cyanide wastewater by solvent extraction was investigated using a quaternary ammonium salt as an extractant. The influences of important parameters, e.g., organic-phase components, aqueous pH values, temperature, inorganic anion impurities, CN/Cu molar ratio, and stripping reagents, were examined systematically, and the optimal conditions were determined. The results indicated that copper was effectively concentrated from low-concentration solutions using Aliquat 336 and that the extraction efficiency increased linearly with increasing temperature. The aqueous pH value and concentrations of inorganic anion impurities only weakly affected the extraction process when varied in appropriate ranges. The CN/Cu molar ratio affected the extraction efficiency by changing the distribution of copper–cyanide complexes. The difference in gold leaching efficiency between using raffinate and fresh water was negligible.
基金the financial support of this work by the Research Council of Mazandaran University.
文摘Copper-catalyzed synthesis of N-aryl anthranilic acid derivatives using effective amination of 2-chloro and 2-bromobenzoic acid under microwave irradiation is reported. Some of the advantages of this method are high chemoselectivity, short reaction times, ease of work up procedure and elimination of the need for acid protection. 2009 Published by Elsevier B.V. on behalf of Chinese Chemical Society.
文摘Separation of copper and nickel by liquid-liquid extraction from aqueous solutions was studied using LIX 664N in kerosene as solvent. Both metals were taken in their sulfate form and ratio of copper to nickel in feed solutions was maintained as 10:1. LIX 664N concentration in kerosene was varied from 10% to 40% (v/v) and its effect was studied on percent extraction of copper and nickel for organic to aqueous (O:A) phase ratio of 2:1 at pH 2. Experimental results showed that at pH 2, copper was selectively extracted from its mixture with nickel. Selectivity for copper extraction was as high as 6000 with 40% LIX 664N. Calculations using extraction isotherm indicate almost complete recovery of copper in two stages with O:A ratio of 1:1 and in one stage with O:A ratio of 2:1. After extraction of copper, the pH of raffinate containing nickel was adjusted to a value of 9 by addition of ammonia solution. The effect of LIX 664N concentration on extraction of nickel was studied. Up to 80% nickel could be extracted with 30% LIX 664N at O:A phase ratio of 2:1. Stripping of copper from the organic phase with 180 g/l sulfuric acid at O:A phase ratio of 1:1 gave 98.5% copper recovery in a two-stage operation.
文摘Nickel, cobalt and copper were separated by solvent extraction with P204. The experimental results show that [Co(NH 3) 6] 3+ is an inert complex in extraction kinetics, therefore cobalt can be separated from nickel and copper by non equilibrium solvent extraction. Under the conditions of temperature 25?℃, contact time of two phases 10?min, phase ratio 1∶1, aqueous pH 10.10 and concentration of P204 20%, [Co(NH 3) 6] 3+ is hardly extracted by P204, while the percentage extractions of nickel and copper are 79.3% and 93.9% respectively. Nickel and copper are separated by equilibrium solvent extraction with P204. Under the conditions of temperature 25?℃, contact time of two phases 1?min, phase ratio 1∶1, equilibrium pH 4.01 and concentration of P204 20%, the separation factor of copper and nickel is 216.
基金the financial support from the Research Council of East Tehran Branch, Islamic Azad University
文摘This paper describes a very simple, efficient synthesis of quinazolinones and chromeno[d]pyrimidinones from the reaction of aryl aldehydes, urea/thiourea and active methylene compounds（dimedone/4-hydroxycoumarin） using nano-sized CuI particles under solvent-free conditions. The highlights of this new method are based on using an effective and recyclable catalyst, affording high yields of products,mild reaction conditions, facile work-up and purification.
基金Project (2004CB619200) supported by the National Basic Research Program of China
文摘The effects of the concentration of Lix 984N,phase ratio,initial pH value of aqueous phase and extraction time on the extraction of copper and iron under the condition of low Cu2+ /Fe3+ ratio in dump bioleaching solution of Dexing Copper Mine were explored.The optimal conditions of extraction are as follows: the concentration of Lix 984N 10%; the phase ratio (O/A) 1:1; the initial pH value of aqueous phase 1.5 and the mixing time 2 min.The stripping experiments show that H2SO4 solution could efficiently recover copper from the organic phase under the optimal conditions.
文摘Lix984N is intimately related to the dynamic characteristics of phase disengagement in copper solvent extraction because of its interfacial activity. With increasing Lix984N content, the phase disengagement time is prolonged and the mechanism dominating phase disengagement process transfers from sedimentation to coalescence. The rate of droplet coalescence is faster than that of droplet sedimentation in the dense dispersion band when the volume fraction of Lix984N is less than 3.0%. The former almost equaled to the latter at Lix984N content of 3.0% and finally becomes lower than the latter when the volume fraction of Lix984N is more than 3.0%. The relationship between the adhesion force of two equal droplets and physical properties of fluids is deduced, which explains that the change of physical properties of organic phase with Lix984N content can make droplet coalescence more difficult and phase disengagement slower.
文摘An experimental investigation was presented on the separation of Cu（Ⅱ）, Zn（Ⅱ）, and Cd（Ⅱ） from a rich sulfate leachate of zinc slag by solvent extraction. The results of orthogonal experiments indicate that LIX 984N is highly selective and very efficient in the extraction of Cu（Ⅱ）, and the analysis of variance indicates that the sequence of parameters according to their influence on the separation efficiency is phase ratio 〉 LIX 984N concentration 〉 pH value 〉 extraction time. The optimal condition for copper extraction is obtained as 25% of LIX 984N concentration, 7 rain of extraction time, 3：2 of phase ratio O/A, and pH = 1.7. The separation of Zn（Ⅱ） and Cd（Ⅱ） was performed after the copper extraction from the raffinate. Comparative analysis of the separation with di-2-ethylhexyl phosphoric acid （D2EHPA）, D2EHPA-tributyl- phosophate （TBP） synergistic extracting system, and 2-ethylhexyl phosphonic acid mono 2-ethylhexyl ester （HEHEHP） was made at pH = 2.0. It is demonstrated that the extraction efficiency with D2EHPA is improved after being saponified by sodium hydroxide, and D2EHPA-TBP synergistic extracting, as well as HEHEHP, has a superior selectivity to Zn（Ⅱ） over Cd（Ⅱ）.
文摘A series of oil products taken from oil refining factories were used as diluents for copper extraction. The influence of diluents on extraction properties has been investigated. The extractants used are Lix984(Henkel) and M5640(Zeneca), and the adaptability of this diluents to these extractants is compared. The checked extraction properties include loading capacity, extraction and strip kinetics, copper/iron selectivity and phase disengagement. The results showed that DSR3 is a suitable diluent for M5640 and Lix984. Further research has been done to reduce the cost of this product by omitting several steps from its production process.
基金ProjectsupportedbytheFoundationforUniversityKeyTeacheroftheMinistryofEducation P .R .China
文摘Extraction of copper from bacterial leach solution using Lix984 had been performed. It was found that the main factors influencing extraction yield of copper are the phase ratio and the concentration of extractant, following the pH of solution and extraction time and the order of factors influencing the separation rate is the pH of solution, the concentration of extractant, the extraction time and the phase ratio. The best conditions obtained by the orthogonal tests are as follows: the extractant concentration 4%, extraction time 3 min, phase ratio 1∶1, pH of solution 2.
文摘研究了N902/煤油从氨/氯化铵水溶液中萃取铜.考察了萃取时间、水相pH值、萃取剂浓度、温度等对萃取率的影响,以及酸度和时间对铜的反萃率的影响.实验发现,在研究的条件下萃取5 m in达到平衡,而反萃则需要15 m in达到平衡.萃取过程是吸热过程,测得△H=4.0 kJ/mol.在实验范围内,萃取率先随pH值增大而增加,当pH值超过10.2后,随着pH值增大反而降低.
