In contrast to conventional transformers, power electronic transformers, as an integral component of new energy power system, are often subjected to high-frequency and transient electrical stresses, leading to heighte...In contrast to conventional transformers, power electronic transformers, as an integral component of new energy power system, are often subjected to high-frequency and transient electrical stresses, leading to heightened concerns regarding insulation failures. Meanwhile, the underlying mechanism behind discharge breakdown failure and nanofiller enhancement under high-frequency electrical stress remains unclear. An electric-thermal coupled discharge breakdown phase field model was constructed to study the evolution of the breakdown path in polyimide nanocomposite insulation subjected to high-frequency stress. The investigation focused on analyzing the effect of various factors, including frequency, temperature, and nanofiller shape, on the breakdown path of Polyimide(PI) composites. Additionally, it elucidated the enhancement mechanism of nano-modified composite insulation at the mesoscopic scale. The results indicated that with increasing frequency and temperature, the discharge breakdown path demonstrates accelerated development, accompanied by a gradual dominance of Joule heat energy. This enhancement is attributed to the dispersed electric field distribution and the hindering effect of the nanosheets. The research findings offer a theoretical foundation and methodological framework to inform the optimal design and performance management of new insulating materials utilized in high-frequency power equipment.展开更多
Acetosyringone （AS） has great influences on Agrobacterium-mediated genetic transformation. In order to improve the transformation frequency of waxy maize, in this study, shoot tips and immature embryo-derived callus...Acetosyringone （AS） has great influences on Agrobacterium-mediated genetic transformation. In order to improve the transformation frequency of waxy maize, in this study, shoot tips and immature embryo-derived callus of Lainongnuo 38 were collected as receptor materials, to compare the effects of pH in suspension medium, addition modes and concentrations of acetosyringone on genetic transformation of waxy maize. Results showed that adding 2 μl of 150 μmol/L AS in the wound with suspension medimn at pH 5.2 can significantly improve the transformation frequency of shoot tips of waxy maize; in genetic transformation of maize callus, adding 5 mg/L AS in infection solution can significantly improve the percentage of resistant callus.展开更多
Ultrahigh resolution synthetic aperture radar(SAR)imaging for ship targets is significant in SAR imaging,but it suffers from high frequency vibration of the platform,which will induce defocus into SAR imaging results....Ultrahigh resolution synthetic aperture radar(SAR)imaging for ship targets is significant in SAR imaging,but it suffers from high frequency vibration of the platform,which will induce defocus into SAR imaging results.In this paper,a novel compensation method based on the sinusoidal frequency modulation Fourier-Bessel transform(SFMFBT)is proposed,it can estimate the vibration errors,and the phase shift ambiguity can be avoided via extracting the time frequency ridge consequently.By constructing the corresponding compensation function and combined with the inverse SAR(ISAR)technique,well-focused imaging results can be obtained.The simulation imaging results of ship targets demonstrate the validity of the proposed approach.展开更多
In the mechanical fault detection and diagnosis field, it is more and more important to analyze the instantaneous frequency （IF） character of complex vibration signal. The improved IF estimation method is put forwar...In the mechanical fault detection and diagnosis field, it is more and more important to analyze the instantaneous frequency （IF） character of complex vibration signal. The improved IF estimation method is put forward aiming at the shortage of traditional Hilbert transform. It is based on Hilbert transform in wavelet domain. With the help of relationship between the real part and the imaginary part obtained from the complex coefficient of continuous wavelet transform or the analyti- cal signal reconstructed in wavelet packet decomposition, the instantaneous phase function of the subcomponent is extracted. In order to improve the precise of IF estimated out, some means such as Linear regression, adaptive filtering, resampling are applied into the instantaneous phase obtained, then, the central differencing operator is used to get desired IF. Simulation results with synthetic and gearbox fault signals are included to illustrate the proposed method.展开更多
Sine Non-linear Chirp Keying(SNCK) is a kind of high-efficient modulation scheme, which provides a potential new beamforming method in communication and radar systems. It has been proved to have advantages in some par...Sine Non-linear Chirp Keying(SNCK) is a kind of high-efficient modulation scheme, which provides a potential new beamforming method in communication and radar systems. It has been proved to have advantages in some parameter estimation issues over conventional modulation schemes. In this paper, a novel transform termed as Discrete Sinusoidal Frequency Modulation transform(DSFMT) is proposed. Then, the DSFMT of SNCK signal is deduced and classified into three types, based on which, the time-bandwidth product is estimated by the proposed algorithm. Simulation results show that the noise has a signifi cant impact on the localization of the peak value and the time-bandwidth product can be estimated by using local ratio values when.展开更多
VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a bac...VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a back-to-back HVDC system, provides faster initial transient recovery, and has better natural damping capability. VFT is simply a DFIM （doubly-fed induction machine） where the machine torque controls the power flow from stator to rotor and vice versa. The main disadvantage of this VFT is the slip rings and brushes required for the rotor circuit, especially in bulk power transmission. The BDFM （brushless doubly-fed machine） with nested cage rotor machine is proved to be a comparable alternative to conventional DFIM in many applications with the advantage that all windings being in the stator frame with fixed output terminals. In this paper, the BDFM is used as a BVFT （brushless variable frequency transformer）. A prototype machine is designed and simulated to verify the system validity.展开更多
This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield...This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield between the primary and secondary windings is designed to minimize eddy current losses, skin and proximity effects, and to reduce the leakage inductance, and the inter winding coupling capacitance. Finite Element Method is employed to analyze the magnetic flux and eddy current distributions. The two different kinds of prototype high frequency transformers are designed and tested. The simulation and experiment results are demonstrated and compared with non-shielded transformers. The shielded transformers have achieved the expected results with a relatively small coupling capacitance, compared with the conventional high frequency transformer. This shield decreases the inter-winding coupling capacitance Cps. The topology of this shield has to be such that it acts as a Faraday screen while avoiding eddy current generation.展开更多
1Ax1 high molecular weight glutenin subunit （HMW-GS） gene expression cassette （GEC） lacking vector backbone sequences together with selectable marker Bar GEC were co-transformed into Chinese hexaploid cultivars Ee...1Ax1 high molecular weight glutenin subunit （HMW-GS） gene expression cassette （GEC） lacking vector backbone sequences together with selectable marker Bar GEC were co-transformed into Chinese hexaploid cultivars Een 1 and Emai 12 to test the feasibility and the efficiency of explant regeneration, transformation frequency and transgene expression comparing with whole vector transformation by the approaches of plasmid extraction and excision, immature embryo isolation, particle co-bombardment, tissue culture, DNA extraction, PCR amplification, southern hybridization, leaf-painting test and SDS-PAGE etc. No significant difference was shown in tissue culture response of the proportion of embryogenic calli, somatic embryogenesis and regeneration frequency between GEC and whole plasmid bombarded embryos, but both regenerated less well than non-bombarded control. Total 56 plantlets that survived PPT selection had insertion of at least the Bar gene, 18 were from the GEC treatment and 38 from the whole plasmid treatment, the escape ratio averaged 0.23. Six independent transplants f230 - f235 with GEC transformation from genotype Emai 12 presented clear PCR amplification bands of Bar and 1Ax1 gene. The transformation and co-transformation frequency were 3.51 and 100% respectively. PCR amplification using a primer-pair specific for ampicillin resistant gene indicated the existence of Amp^R gene in whole vectors but the removal in GECs and transplants. Southern blot of total DNA and PCR products from transgenic plants of 1Ax1 GEC confirmed the integration of the transgene 1Ax1 and the absence of the EcoR Ⅰ recognition site at both ends of the 1Ax1 GEC when integrated. SDS-PAGE showed the expression of 1Ax1 GEC and un-expression of whole plasmid. The length of integrated fragment, the proportion of the gene of interest （GOI） and the selectable marker （MG）, bombardment pressure and genotypes are vital for the expression of a transformed GEC.展开更多
Stratigraphic correlations are essential for the fine-scale characterization of reservoirs.However,conventional data-driven methods that rely solely on log data struggle to construct isochronous stratigraphic framewor...Stratigraphic correlations are essential for the fine-scale characterization of reservoirs.However,conventional data-driven methods that rely solely on log data struggle to construct isochronous stratigraphic frameworks for complex sedimentary environments and multi-source geological settings.In response,this study proposed an intelligent,automatic,log-seismic integrated stratigraphic correlation method that incorporates wavelet frequency-division transform(WFT)and dynamic time warping(DTW)(also referred to as the WFT-DTW method).This approach integrates seismic data as constraints into stratigraphic correlations,enabling accurate tracking of the seismic marker horizons through WFT.Under the constraints of framework construction,a DTW algorithm was introduced to correlate sublayer boundaries automatically.The effectiveness of the proposed method was verified through a stratigraphic correlation experiment on the SA0 Formation of the Xingshugang block in the Lasaxing oilfield,the Songliao Basin,China.In this block,the target layer exhibits sublayer thicknesses ranging from 5 m to 8 m,an average sandstone thickness of 2.1 m,and pronounced heterogeneity.The verification using 1760 layers in 160 post-test wells indicates that the WFT-DTW method intelligently compared sublayers in zones with underdeveloped faults and distinct marker horizons.As a result,the posterior correlation of 1682 layers was performed,with a coincidence rate of up to 95.6%.The proposed method can complement manual correlation efforts while also providing valuable technical support for the lithologic and sand body characterization of reservoirs.展开更多
Quickly and accurately obtaining the internal temperature distribution of a transformer plays a key role in predicting its operating conditions and simplifying the maintenance process.A reasonable equivalent thermal c...Quickly and accurately obtaining the internal temperature distribution of a transformer plays a key role in predicting its operating conditions and simplifying the maintenance process.A reasonable equivalent thermal circuit model is a relatively reliable method of obtaining the internal temperature distribution.However,thermal circuit models without targeted consideration of operating conditions and parameter corrections usually limit the accuracy of the results.This paper proposed a five-node transient thermal circuit model with the introduction of nonlinear thermal resistance,which considered the internal structure and winding layout of the core-type high-frequency transformer.The Nusselt number,a crucial variable in heat convection calculations and directly related to the accuracy of thermal resistance parameters,was calibrated on the basis of the distribution of external cooling air.After parameter calibration,the maximum computational error of the hotspot temperature is reduced by 5.48%compared with that of the uncalibrated model.Finally,an experimental platform for temperature monitoring was established to validate the five-node model and its ability to track the temperature change at each reference point after calibrating the Nusselt number.展开更多
In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation （CPPM） and linear frequency modulation （LFM）, which can be widely used in electronic count...In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation （CPPM） and linear frequency modulation （LFM）, which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval （PRI） of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform （CHT） algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio （SNR） is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.展开更多
This article proposes a new transceiver design for Single carrier frequency division multiple access(SCFDMA)system based on discrete wavelet transform(DWT). SCFDMA offers almost same structure as Orthogonal frequency ...This article proposes a new transceiver design for Single carrier frequency division multiple access(SCFDMA)system based on discrete wavelet transform(DWT). SCFDMA offers almost same structure as Orthogonal frequency division multiple access(OFDMA)with extra advantage of low Peak to Average Power Ratio(PAPR). Moreover,this article also suggests the application of Walsh Hadamard transform(WHT)for linear precoding(LP)to improve the PAPR performance of the system. Supremacy of the proposed transceiver over conventional Fast Fourier transform(FFT)based SCFDMA is shown through simulated results in terms of PAPR,spectral efficiency(SE)and bit error rate(BER).展开更多
Based on the fact that it is diffi cult to implement optimum inversion using 2D and 3D forward modeling with magnetic-source transient electromagnetics(TEM),this paper explores a novel approach to the implementation o...Based on the fact that it is diffi cult to implement optimum inversion using 2D and 3D forward modeling with magnetic-source transient electromagnetics(TEM),this paper explores a novel approach to the implementation of 2D magnetic-source TEM inversion.In particular,we converted magnetic-source TEM data into magnetotelluric(MT)data and then used a 2D MT inversion method to implement a 2D magnetic-source TEM inversion interpretation.First,we studied the similarity between magnetic-source TEM waves and MT waves and between magnetic-source TEM all-time apparent resistivity and MT Cagniard apparent resistivity.Then,we selected an optimal time-frequency transformation coeffi cient to implement rapid time-frequency transformation of all-time TEM apparent resistivity to MT Cagniard apparent resistivity.Afterward,we conducted 1D pseudo-MT inversions of magnetic-source 1D TEM theoretical models.The 1D inversion results demonstrated that the diff erence between the inversion parameters and model parameters was small,while the MT 1D inversion method could be used to conduct magnetic 1D TEM inversion within a certain margin of error.We further conducted 2D pseudo-MT inversions of 3D magnetic-source TEM theoretical models,and the 2D inversion results indicated that selecting a joint 2D pseudo-MT transverse-electric(TE)and transverse-magnetic(TM)inversion method based on measuring the line above a 3D anomalous body can help to accurately implement a 2D inversion interpretation of the 3D TEM response.展开更多
The multiphase boost DC-DC converter with stable control strategy is presented. Multi- phase boost DC-DC converter is designed for high voltage and high power applications, and could be achieved by the adjustment of v...The multiphase boost DC-DC converter with stable control strategy is presented. Multi- phase boost DC-DC converter is designed for high voltage and high power applications, and could be achieved by the adjustment of voltage doubler rectifiers on the secondary side of high frequency transformers. The stable control strategy for three phase boost DC-DC converter has been utilized during simulation in this study and this strategy can be extend to N-number of phases. The stable control strategy consists of only three voltage loops, which are sufficient for appropriate and efficient operation of three phase boost DC-DC converter. With the stable control strategy, the equal power balance sharing can be obtained between input and output. The stability of control strategy has been evaluated by simulating the multiphase boost DC-DC converter for the same and mismatch turn ratios of high frequency transformers. The simulation result is good and the objective of the strategy is a- chieved.展开更多
Associated with ITU-T G.719,a post-processing method in frequency domain for enhancing the perceptual quality of the decoded transient audio is proposed only to the audio decoder with no side information from the enco...Associated with ITU-T G.719,a post-processing method in frequency domain for enhancing the perceptual quality of the decoded transient audio is proposed only to the audio decoder with no side information from the encoder.The proposed post-filter is used to filter the frequency coefficients of the decoded transient frame and consists of a short-term post-filter and a spectral tilt compensation filter which are derived from linear predictive coding（LPC） predictor based on the discrete cosine transform（DCT） coefficients of the decoded transient frame.As a result,the post-filter in frequency domain shapes the temporal noise in time domain and controls the pre-echo noise effectively while enhancing the transient perception.Listening test results show that the preferring ratio of the post-processed transient signal is higher than that of the original decoded signal at a low bit rate of 32 kbit/s in G.719 and the post-processing module brings a complexity of 12.399 WMOPS to the decoder.展开更多
This paper introduces an isolated reversible DC-DC converter with a particular topology, which benefits from both the NPC （neutral point clamped） structure and the series-parallel connection of converters. The key p...This paper introduces an isolated reversible DC-DC converter with a particular topology, which benefits from both the NPC （neutral point clamped） structure and the series-parallel connection of converters. The key property of the proposed topology is the output voltage elevation above the blocking capabilities of each switch, without taking to a delicate synchronization of series-connected semiconductors. The converter is composed by two identical cells, each containing a full bridge, a medium frequency transformer and an NPC converter, connected in parallel at the input and in series at the output. The operation principle of each cell, into which a trapezoidal modulation was implemented, is similar to a DAB （dual active bridge）. A new model improves the dynamic performance of the controller. Simulation and experimental results verify the proposed topology, its control and start-up strategy.展开更多
Objective:PCG represents the acoustic replay of heart sounds from the cardiac structure.To detect and analyse the different conditions of the heart,heart sound signals are essential.CVD is detected by classifiers who ...Objective:PCG represents the acoustic replay of heart sounds from the cardiac structure.To detect and analyse the different conditions of the heart,heart sound signals are essential.CVD is detected by classifiers who superficially identify the cardiac features.Abnormal sounds in systole or diastole could indicate valve stenosis or regurgitation.The presence of S3 or S4 sounds could indicate heart failure or stiffening of the heart muscle.This paper proposes a CVD detection technique using improved WST and DA classifiers.Method:The PCG was obtained from the Physionet dataset.The raw signals were pre-processed using 2D DCT.The 2D DCT was applied to a matrix containing 3000 sounds with 10000 samples.The DCT matrix was then filtered using a 20Hz–190 Hz Type II Chebyshev filter to remove the high frequency noise above 190 Hz.After filtering,the denoised PCG matrix was obtained from the DCT matrix using inverse 2D DCT.The PCG matrix was feature extracted using WST.WST produces low-frequency components by using the LPFs to filter high-frequency components.These features were then used with the DA classifier to predict the CVD.The DA classifier uses discriminant analysis pattern classification.The DA classifier learns the training PCG pattern,from WST features,and then classifies test samples as normal or abnormal.Results:The proposed method removed noise up to 99%.The 2D DCT filter provided an average noise improvement of 37.34 dB.Further tuning in filter order or attenuation level resulted in distortion of the PCG,and noise improvement declined.The DCT filter removed up to 99%of noise as per the SNR estimation.The improved WST and the DA classifier resulted in an accuracy of 99.63%.Conclusion:Comparative analysis with DNN,advocates the superiority of the proposed method.DNN classifiers provide accurate CVD classification but require a more expensive and complex GPU.The DA classifier requires only a CPU.This work demonstrated that superior CVD classification was obtained using a combination of WST features and the DA classifier with 94%accuracy.展开更多
Against the deficiencies of traditional time domain and frequency domain analysis in detecting wheel-rail （W-R） system hidden risks which wheel flats generate, the time-frequency characteristics of W-R shock caused ...Against the deficiencies of traditional time domain and frequency domain analysis in detecting wheel-rail （W-R） system hidden risks which wheel flats generate, the time-frequency characteristics of W-R shock caused by wheel flat are analyzed and the vehicle-rail dynamic model with wheel flat is investigated. The 10 degrees of freedom （DOF） vehicle model is built up. 90-DOF rail model is constructed. The wheel flat excitation model is built up. The vehicle-track coupling dynamic model including wheel flat excitation is set up through nonlinear Hertzian contact theory. The vertical accelerations of axle box are calculated at different speeds and flat sizes based on the vehicle-track coupling dynamic model with wheel flat. Frequency slice wavelet transform （FSWT） is employed to analyze time- frequency characteristics of axle box accelerations to detect the W-R noncontact risks, which the traditional time domain or frequency domain method does not analyze. The results show that the small flat size and high running speed lead to high frequency W-R impact. Large flat size and high running speed result in momentary loss of W-R contact, and there exist security risks between wheel and rail. The conclusion that the phase of axle box accelerations is same to W-R forces lays a theoretical foundation of monitoring W-R contact safety from axle box acceleration instead of traditional W-R force detection.展开更多
The nonparametric kernel estimation of probability density function (PDF) pro-vides a uniform and accurate estimate of flood frequency-magnitude relationship.However, the kernel estimate has the disadvantage that the ...The nonparametric kernel estimation of probability density function (PDF) pro-vides a uniform and accurate estimate of flood frequency-magnitude relationship.However, the kernel estimate has the disadvantage that the smoothing factor h is estimate empirically and is not locally adjusted, thus possibly resulting in deteri oration of density estimate when PDF is not smooth and is heavy-tailed. Such a problem can be alleviate by estimating the density of a transformed random vari able, and then taking the inverse transform. A new and efficient circular transform is proposed and investigated in this paper展开更多
Ultrasonic backscatter signals from cancellous bone are sensitive to the microstructure of trabecular bone,and thus enable the feasibility to extract microstructural information of trabecular bone.The mean trabecular ...Ultrasonic backscatter signals from cancellous bone are sensitive to the microstructure of trabecular bone,and thus enable the feasibility to extract microstructural information of trabecular bone.The mean trabecular bone spacing(MTBS)is an important parameter for characterizing bone microstructure.This paper proposes an MTBS estimation method based on the combination of Hilbert transform and fundamental frequency estimation(CHF). The CHF was verified with ultrasonic backscatter signals from simulations and in vitro measurements at a central frequency of 5MHz.The CHF method was compared with the simplified inverse filter tracking(SIFT)method,Simons' Quadratic Transformation(QT)method,Singular Spectrum Analysis(SSA)method,and Spectral Autocorrelation(SAC)method.Monte-Carlo simulations were performed by varying the MTBS,signal-to-noise ratio(SNR),standard deviation of regular spacing(SDRS),amplitude ratio of diffuse scattering to regular scattering(Ad)and frequency dependent attenuation(nBUA).The simulation results showed that the CHF method had a better performance in MTBS estimation under almost all the examination conditions except for SNR.The estimation percentage correct(EPC)was greater than 90% when the MTBS was in the range of 0.4to 1.4mm.In the in vitro measurements,the estimated EPC by the CHF method was91.25±7.81%(mean±standard deviation).A significant correlation was observed for the CHF-estimated MTBS and micro-computed tomography(μ-CT)-measured values(R^2=0.75,p<0.01).These results demonstrate that the CHF method is anti-interference for MTBS estimation and can be used to estimate trabecular bone spacing.展开更多
基金supported in part by the National Key R&D Program of China (No.2021YFB2601404)Beijing Natural Science Foundation (No.3232053)National Natural Science Foundation of China (Nos.51929701 and 52127812)。
文摘In contrast to conventional transformers, power electronic transformers, as an integral component of new energy power system, are often subjected to high-frequency and transient electrical stresses, leading to heightened concerns regarding insulation failures. Meanwhile, the underlying mechanism behind discharge breakdown failure and nanofiller enhancement under high-frequency electrical stress remains unclear. An electric-thermal coupled discharge breakdown phase field model was constructed to study the evolution of the breakdown path in polyimide nanocomposite insulation subjected to high-frequency stress. The investigation focused on analyzing the effect of various factors, including frequency, temperature, and nanofiller shape, on the breakdown path of Polyimide(PI) composites. Additionally, it elucidated the enhancement mechanism of nano-modified composite insulation at the mesoscopic scale. The results indicated that with increasing frequency and temperature, the discharge breakdown path demonstrates accelerated development, accompanied by a gradual dominance of Joule heat energy. This enhancement is attributed to the dispersed electric field distribution and the hindering effect of the nanosheets. The research findings offer a theoretical foundation and methodological framework to inform the optimal design and performance management of new insulating materials utilized in high-frequency power equipment.
基金Supported by National Natural Science Foundation of China(31201218)National Science and Technology Project of "Twelfth Five Year" Plan of China(2011BAD35B01)+3 种基金Taishan Scholars Program of Shandong Province(Crop Cultivation and Breeding)Basic Research Program of Science and Technology Project of Qingdao City[12-1-4-5-(11)-jch]Starting Fund for High-level Personnel of Qingdao Agricultural University(No.630740)Shandong Key Laboratory of Maize Breeding and Cultivation Techniques
文摘Acetosyringone （AS） has great influences on Agrobacterium-mediated genetic transformation. In order to improve the transformation frequency of waxy maize, in this study, shoot tips and immature embryo-derived callus of Lainongnuo 38 were collected as receptor materials, to compare the effects of pH in suspension medium, addition modes and concentrations of acetosyringone on genetic transformation of waxy maize. Results showed that adding 2 μl of 150 μmol/L AS in the wound with suspension medimn at pH 5.2 can significantly improve the transformation frequency of shoot tips of waxy maize; in genetic transformation of maize callus, adding 5 mg/L AS in infection solution can significantly improve the percentage of resistant callus.
基金supported by the National Natural Science Foundation of China(61871146)the Fundamental Research Funds for the Central Universities(FRFCU5710093720)。
文摘Ultrahigh resolution synthetic aperture radar(SAR)imaging for ship targets is significant in SAR imaging,but it suffers from high frequency vibration of the platform,which will induce defocus into SAR imaging results.In this paper,a novel compensation method based on the sinusoidal frequency modulation Fourier-Bessel transform(SFMFBT)is proposed,it can estimate the vibration errors,and the phase shift ambiguity can be avoided via extracting the time frequency ridge consequently.By constructing the corresponding compensation function and combined with the inverse SAR(ISAR)technique,well-focused imaging results can be obtained.The simulation imaging results of ship targets demonstrate the validity of the proposed approach.
基金This project is supported by National Natural Science Foundation of China (No.50605065)Natural Science Foundation Project of CQ CSTC(No.2007BB2142).
文摘In the mechanical fault detection and diagnosis field, it is more and more important to analyze the instantaneous frequency （IF） character of complex vibration signal. The improved IF estimation method is put forward aiming at the shortage of traditional Hilbert transform. It is based on Hilbert transform in wavelet domain. With the help of relationship between the real part and the imaginary part obtained from the complex coefficient of continuous wavelet transform or the analyti- cal signal reconstructed in wavelet packet decomposition, the instantaneous phase function of the subcomponent is extracted. In order to improve the precise of IF estimated out, some means such as Linear regression, adaptive filtering, resampling are applied into the instantaneous phase obtained, then, the central differencing operator is used to get desired IF. Simulation results with synthetic and gearbox fault signals are included to illustrate the proposed method.
基金supported by Science and Technology on Information Transmission and Dissemination in Communication Networks Laboratory(KX152600015/ITD-U15006)National Natural Science Foundation of China(No.61401196)
文摘Sine Non-linear Chirp Keying(SNCK) is a kind of high-efficient modulation scheme, which provides a potential new beamforming method in communication and radar systems. It has been proved to have advantages in some parameter estimation issues over conventional modulation schemes. In this paper, a novel transform termed as Discrete Sinusoidal Frequency Modulation transform(DSFMT) is proposed. Then, the DSFMT of SNCK signal is deduced and classified into three types, based on which, the time-bandwidth product is estimated by the proposed algorithm. Simulation results show that the noise has a signifi cant impact on the localization of the peak value and the time-bandwidth product can be estimated by using local ratio values when.
文摘VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a back-to-back HVDC system, provides faster initial transient recovery, and has better natural damping capability. VFT is simply a DFIM （doubly-fed induction machine） where the machine torque controls the power flow from stator to rotor and vice versa. The main disadvantage of this VFT is the slip rings and brushes required for the rotor circuit, especially in bulk power transmission. The BDFM （brushless doubly-fed machine） with nested cage rotor machine is proved to be a comparable alternative to conventional DFIM in many applications with the advantage that all windings being in the stator frame with fixed output terminals. In this paper, the BDFM is used as a BVFT （brushless variable frequency transformer）. A prototype machine is designed and simulated to verify the system validity.
文摘This paper presents and investigates planar and coaxial high frequency power transformers used for DC/DC converters in a three phase photo voltaic （PV） power systems. The winding structure including a Faraday shield between the primary and secondary windings is designed to minimize eddy current losses, skin and proximity effects, and to reduce the leakage inductance, and the inter winding coupling capacitance. Finite Element Method is employed to analyze the magnetic flux and eddy current distributions. The two different kinds of prototype high frequency transformers are designed and tested. The simulation and experiment results are demonstrated and compared with non-shielded transformers. The shielded transformers have achieved the expected results with a relatively small coupling capacitance, compared with the conventional high frequency transformer. This shield decreases the inter-winding coupling capacitance Cps. The topology of this shield has to be such that it acts as a Faraday screen while avoiding eddy current generation.
基金supported by China Post-Doctorial Foundation(2002031255)Rothamsted International Foundation(2002)of the UKNatural Science Foundation of Zhejiang Province,China(M303081).
文摘1Ax1 high molecular weight glutenin subunit （HMW-GS） gene expression cassette （GEC） lacking vector backbone sequences together with selectable marker Bar GEC were co-transformed into Chinese hexaploid cultivars Een 1 and Emai 12 to test the feasibility and the efficiency of explant regeneration, transformation frequency and transgene expression comparing with whole vector transformation by the approaches of plasmid extraction and excision, immature embryo isolation, particle co-bombardment, tissue culture, DNA extraction, PCR amplification, southern hybridization, leaf-painting test and SDS-PAGE etc. No significant difference was shown in tissue culture response of the proportion of embryogenic calli, somatic embryogenesis and regeneration frequency between GEC and whole plasmid bombarded embryos, but both regenerated less well than non-bombarded control. Total 56 plantlets that survived PPT selection had insertion of at least the Bar gene, 18 were from the GEC treatment and 38 from the whole plasmid treatment, the escape ratio averaged 0.23. Six independent transplants f230 - f235 with GEC transformation from genotype Emai 12 presented clear PCR amplification bands of Bar and 1Ax1 gene. The transformation and co-transformation frequency were 3.51 and 100% respectively. PCR amplification using a primer-pair specific for ampicillin resistant gene indicated the existence of Amp^R gene in whole vectors but the removal in GECs and transplants. Southern blot of total DNA and PCR products from transgenic plants of 1Ax1 GEC confirmed the integration of the transgene 1Ax1 and the absence of the EcoR Ⅰ recognition site at both ends of the 1Ax1 GEC when integrated. SDS-PAGE showed the expression of 1Ax1 GEC and un-expression of whole plasmid. The length of integrated fragment, the proportion of the gene of interest （GOI） and the selectable marker （MG）, bombardment pressure and genotypes are vital for the expression of a transformed GEC.
基金funded by the Major Science and Technology Project of China National Petroleum Corporation(No.2023ZZ22YJ01).
文摘Stratigraphic correlations are essential for the fine-scale characterization of reservoirs.However,conventional data-driven methods that rely solely on log data struggle to construct isochronous stratigraphic frameworks for complex sedimentary environments and multi-source geological settings.In response,this study proposed an intelligent,automatic,log-seismic integrated stratigraphic correlation method that incorporates wavelet frequency-division transform(WFT)and dynamic time warping(DTW)(also referred to as the WFT-DTW method).This approach integrates seismic data as constraints into stratigraphic correlations,enabling accurate tracking of the seismic marker horizons through WFT.Under the constraints of framework construction,a DTW algorithm was introduced to correlate sublayer boundaries automatically.The effectiveness of the proposed method was verified through a stratigraphic correlation experiment on the SA0 Formation of the Xingshugang block in the Lasaxing oilfield,the Songliao Basin,China.In this block,the target layer exhibits sublayer thicknesses ranging from 5 m to 8 m,an average sandstone thickness of 2.1 m,and pronounced heterogeneity.The verification using 1760 layers in 160 post-test wells indicates that the WFT-DTW method intelligently compared sublayers in zones with underdeveloped faults and distinct marker horizons.As a result,the posterior correlation of 1682 layers was performed,with a coincidence rate of up to 95.6%.The proposed method can complement manual correlation efforts while also providing valuable technical support for the lithologic and sand body characterization of reservoirs.
基金supported by the National Natural Science Foundation of China(Grant 52207180)Xi'an High Voltage Apparatus Research Institute Co.Ltd.(Grant K222301-01)the Anhui Provincial Natural Science Foundation(Grant 2208085UD18).
文摘Quickly and accurately obtaining the internal temperature distribution of a transformer plays a key role in predicting its operating conditions and simplifying the maintenance process.A reasonable equivalent thermal circuit model is a relatively reliable method of obtaining the internal temperature distribution.However,thermal circuit models without targeted consideration of operating conditions and parameter corrections usually limit the accuracy of the results.This paper proposed a five-node transient thermal circuit model with the introduction of nonlinear thermal resistance,which considered the internal structure and winding layout of the core-type high-frequency transformer.The Nusselt number,a crucial variable in heat convection calculations and directly related to the accuracy of thermal resistance parameters,was calibrated on the basis of the distribution of external cooling air.After parameter calibration,the maximum computational error of the hotspot temperature is reduced by 5.48%compared with that of the uncalibrated model.Finally,an experimental platform for temperature monitoring was established to validate the five-node model and its ability to track the temperature change at each reference point after calibrating the Nusselt number.
基金supported by the National Natural Science Foundation of China under Grant 61172116
文摘In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation （CPPM） and linear frequency modulation （LFM）, which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval （PRI） of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform （CHT） algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio （SNR） is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.
文摘This article proposes a new transceiver design for Single carrier frequency division multiple access(SCFDMA)system based on discrete wavelet transform(DWT). SCFDMA offers almost same structure as Orthogonal frequency division multiple access(OFDMA)with extra advantage of low Peak to Average Power Ratio(PAPR). Moreover,this article also suggests the application of Walsh Hadamard transform(WHT)for linear precoding(LP)to improve the PAPR performance of the system. Supremacy of the proposed transceiver over conventional Fast Fourier transform(FFT)based SCFDMA is shown through simulated results in terms of PAPR,spectral efficiency(SE)and bit error rate(BER).
基金this research project is funded by a major science and technology project of Gansu province,“research on the complete set technology for highway construction in collapsible loess region of Gansu province”(No.1302GKDA009).
文摘Based on the fact that it is diffi cult to implement optimum inversion using 2D and 3D forward modeling with magnetic-source transient electromagnetics(TEM),this paper explores a novel approach to the implementation of 2D magnetic-source TEM inversion.In particular,we converted magnetic-source TEM data into magnetotelluric(MT)data and then used a 2D MT inversion method to implement a 2D magnetic-source TEM inversion interpretation.First,we studied the similarity between magnetic-source TEM waves and MT waves and between magnetic-source TEM all-time apparent resistivity and MT Cagniard apparent resistivity.Then,we selected an optimal time-frequency transformation coeffi cient to implement rapid time-frequency transformation of all-time TEM apparent resistivity to MT Cagniard apparent resistivity.Afterward,we conducted 1D pseudo-MT inversions of magnetic-source 1D TEM theoretical models.The 1D inversion results demonstrated that the diff erence between the inversion parameters and model parameters was small,while the MT 1D inversion method could be used to conduct magnetic 1D TEM inversion within a certain margin of error.We further conducted 2D pseudo-MT inversions of 3D magnetic-source TEM theoretical models,and the 2D inversion results indicated that selecting a joint 2D pseudo-MT transverse-electric(TE)and transverse-magnetic(TM)inversion method based on measuring the line above a 3D anomalous body can help to accurately implement a 2D inversion interpretation of the 3D TEM response.
文摘The multiphase boost DC-DC converter with stable control strategy is presented. Multi- phase boost DC-DC converter is designed for high voltage and high power applications, and could be achieved by the adjustment of voltage doubler rectifiers on the secondary side of high frequency transformers. The stable control strategy for three phase boost DC-DC converter has been utilized during simulation in this study and this strategy can be extend to N-number of phases. The stable control strategy consists of only three voltage loops, which are sufficient for appropriate and efficient operation of three phase boost DC-DC converter. With the stable control strategy, the equal power balance sharing can be obtained between input and output. The stability of control strategy has been evaluated by simulating the multiphase boost DC-DC converter for the same and mismatch turn ratios of high frequency transformers. The simulation result is good and the objective of the strategy is a- chieved.
基金Supported by the Cooperation Between BIT and Ericsson
文摘Associated with ITU-T G.719,a post-processing method in frequency domain for enhancing the perceptual quality of the decoded transient audio is proposed only to the audio decoder with no side information from the encoder.The proposed post-filter is used to filter the frequency coefficients of the decoded transient frame and consists of a short-term post-filter and a spectral tilt compensation filter which are derived from linear predictive coding（LPC） predictor based on the discrete cosine transform（DCT） coefficients of the decoded transient frame.As a result,the post-filter in frequency domain shapes the temporal noise in time domain and controls the pre-echo noise effectively while enhancing the transient perception.Listening test results show that the preferring ratio of the post-processed transient signal is higher than that of the original decoded signal at a low bit rate of 32 kbit/s in G.719 and the post-processing module brings a complexity of 12.399 WMOPS to the decoder.
文摘This paper introduces an isolated reversible DC-DC converter with a particular topology, which benefits from both the NPC （neutral point clamped） structure and the series-parallel connection of converters. The key property of the proposed topology is the output voltage elevation above the blocking capabilities of each switch, without taking to a delicate synchronization of series-connected semiconductors. The converter is composed by two identical cells, each containing a full bridge, a medium frequency transformer and an NPC converter, connected in parallel at the input and in series at the output. The operation principle of each cell, into which a trapezoidal modulation was implemented, is similar to a DAB （dual active bridge）. A new model improves the dynamic performance of the controller. Simulation and experimental results verify the proposed topology, its control and start-up strategy.
文摘Objective:PCG represents the acoustic replay of heart sounds from the cardiac structure.To detect and analyse the different conditions of the heart,heart sound signals are essential.CVD is detected by classifiers who superficially identify the cardiac features.Abnormal sounds in systole or diastole could indicate valve stenosis or regurgitation.The presence of S3 or S4 sounds could indicate heart failure or stiffening of the heart muscle.This paper proposes a CVD detection technique using improved WST and DA classifiers.Method:The PCG was obtained from the Physionet dataset.The raw signals were pre-processed using 2D DCT.The 2D DCT was applied to a matrix containing 3000 sounds with 10000 samples.The DCT matrix was then filtered using a 20Hz–190 Hz Type II Chebyshev filter to remove the high frequency noise above 190 Hz.After filtering,the denoised PCG matrix was obtained from the DCT matrix using inverse 2D DCT.The PCG matrix was feature extracted using WST.WST produces low-frequency components by using the LPFs to filter high-frequency components.These features were then used with the DA classifier to predict the CVD.The DA classifier uses discriminant analysis pattern classification.The DA classifier learns the training PCG pattern,from WST features,and then classifies test samples as normal or abnormal.Results:The proposed method removed noise up to 99%.The 2D DCT filter provided an average noise improvement of 37.34 dB.Further tuning in filter order or attenuation level resulted in distortion of the PCG,and noise improvement declined.The DCT filter removed up to 99%of noise as per the SNR estimation.The improved WST and the DA classifier resulted in an accuracy of 99.63%.Conclusion:Comparative analysis with DNN,advocates the superiority of the proposed method.DNN classifiers provide accurate CVD classification but require a more expensive and complex GPU.The DA classifier requires only a CPU.This work demonstrated that superior CVD classification was obtained using a combination of WST features and the DA classifier with 94%accuracy.
基金supported by the National Natural Science Foundation of China(No.51305358,61134002)
文摘Against the deficiencies of traditional time domain and frequency domain analysis in detecting wheel-rail （W-R） system hidden risks which wheel flats generate, the time-frequency characteristics of W-R shock caused by wheel flat are analyzed and the vehicle-rail dynamic model with wheel flat is investigated. The 10 degrees of freedom （DOF） vehicle model is built up. 90-DOF rail model is constructed. The wheel flat excitation model is built up. The vehicle-track coupling dynamic model including wheel flat excitation is set up through nonlinear Hertzian contact theory. The vertical accelerations of axle box are calculated at different speeds and flat sizes based on the vehicle-track coupling dynamic model with wheel flat. Frequency slice wavelet transform （FSWT） is employed to analyze time- frequency characteristics of axle box accelerations to detect the W-R noncontact risks, which the traditional time domain or frequency domain method does not analyze. The results show that the small flat size and high running speed lead to high frequency W-R impact. Large flat size and high running speed result in momentary loss of W-R contact, and there exist security risks between wheel and rail. The conclusion that the phase of axle box accelerations is same to W-R forces lays a theoretical foundation of monitoring W-R contact safety from axle box acceleration instead of traditional W-R force detection.
文摘The nonparametric kernel estimation of probability density function (PDF) pro-vides a uniform and accurate estimate of flood frequency-magnitude relationship.However, the kernel estimate has the disadvantage that the smoothing factor h is estimate empirically and is not locally adjusted, thus possibly resulting in deteri oration of density estimate when PDF is not smooth and is heavy-tailed. Such a problem can be alleviate by estimating the density of a transformed random vari able, and then taking the inverse transform. A new and efficient circular transform is proposed and investigated in this paper
基金supported by the NSFC(11327405,11504057&11525416)
文摘Ultrasonic backscatter signals from cancellous bone are sensitive to the microstructure of trabecular bone,and thus enable the feasibility to extract microstructural information of trabecular bone.The mean trabecular bone spacing(MTBS)is an important parameter for characterizing bone microstructure.This paper proposes an MTBS estimation method based on the combination of Hilbert transform and fundamental frequency estimation(CHF). The CHF was verified with ultrasonic backscatter signals from simulations and in vitro measurements at a central frequency of 5MHz.The CHF method was compared with the simplified inverse filter tracking(SIFT)method,Simons' Quadratic Transformation(QT)method,Singular Spectrum Analysis(SSA)method,and Spectral Autocorrelation(SAC)method.Monte-Carlo simulations were performed by varying the MTBS,signal-to-noise ratio(SNR),standard deviation of regular spacing(SDRS),amplitude ratio of diffuse scattering to regular scattering(Ad)and frequency dependent attenuation(nBUA).The simulation results showed that the CHF method had a better performance in MTBS estimation under almost all the examination conditions except for SNR.The estimation percentage correct(EPC)was greater than 90% when the MTBS was in the range of 0.4to 1.4mm.In the in vitro measurements,the estimated EPC by the CHF method was91.25±7.81%(mean±standard deviation).A significant correlation was observed for the CHF-estimated MTBS and micro-computed tomography(μ-CT)-measured values(R^2=0.75,p<0.01).These results demonstrate that the CHF method is anti-interference for MTBS estimation and can be used to estimate trabecular bone spacing.
