A SiC/ZrSiO4？SiO2 （SZS） coating was successfully fabricated on the carbon/carbon （C/C） composites by pack cementation, slurry painting and sintering to improve the anti-oxidation property and thermal shock r...A SiC/ZrSiO4？SiO2 （SZS） coating was successfully fabricated on the carbon/carbon （C/C） composites by pack cementation, slurry painting and sintering to improve the anti-oxidation property and thermal shock resistance. The anti-oxidation properties under different oxygen partial pressures （OPP） and thermal shock resistance of the SZS coating were investigated. The results show that the SZS coated sample under low OPP, corresponding to the ambient air, during isothermal oxidation was 0.54% in mass gain after 111 h oxidation at 1500 ° C and less than 0.03% in mass loss after 50 h oxidation in high OPP, corresponding to the air flow rate of 36 L/h. Additionally, the residual compressive strengths （RCS） of the SZS coated samples after oxidation for 50 h in high OPP and 80 h in low OPP remain about 70% and 72.5% of those of original C/C samples, respectively. Moreover, the mass loss of SZS coated samples subjected to the thermal cycle from 1500 ° C in high OPP to boiling water for 30 times was merely 1.61%.展开更多
Composite membranes have attracted increasing attentions owing to their potential applications for CO2 separation. In this work, ceramic supported polydimethylsiloxane （PDMS） and poly （ethylene glycol） diacrylate ...Composite membranes have attracted increasing attentions owing to their potential applications for CO2 separation. In this work, ceramic supported polydimethylsiloxane （PDMS） and poly （ethylene glycol） diacrylate （PEGDA） composite membranes were prepared. The microstructure and physicochemical properties of the compos- ite membranes were characterized. Preparation conditions were systematically optimized. The gas separation performance of the as-prepared membranes was studied by pure gas and binary gas permeation measurement of CO〉 N2 and H〉 Experiments showed that PDMS, as silicone rubber, exhibited larger permeance and lower separation factors. Conversely, PEGDA composite membrane presented smaller gas permeance but higher ideal selectivity for CO2/N2. Compared to the performance of those membranes using polymeric supports or freestanding membranes, the two kinds of ceramic supported composite membranes exhibited higher gas permeance and acceptable selectivity. Therefore, the ceramic supported composite membrane can be expected as a candidate for CO2 separation from light gases.展开更多
BNp/Al2O3-SiO2 system ceramic matrix composites with different volume fractions （10%-60%） of hexagonal BN particulates （BNp） were prepared by hot-press sintering technique. Phase components, microstructure, mechan...BNp/Al2O3-SiO2 system ceramic matrix composites with different volume fractions （10%-60%） of hexagonal BN particulates （BNp） were prepared by hot-press sintering technique. Phase components, microstructure, mechanical properties and plasma erosion resistance were also investigated. With the increase of h-BNp content, relative density and Vickers＇ hardness of the composite ceramics decrease, while the flexural strength, elastic modulus and fracture toughness increase and then decrease. The plasma erosion resistance linearly deteriorated with the increase of BNp content which is mainly determined by the density, crystal structure and atomic number of the elements.展开更多
Based on the γ-Al2O3 support with large-size pores, impregnation-deposition method was adopted to prepare the nano CeO_2/γ-Al2O3 composite supports. The results of XRD showed that there was no CeO_2-Al2O3 mixture or...Based on the γ-Al2O3 support with large-size pores, impregnation-deposition method was adopted to prepare the nano CeO_2/γ-Al2O3 composite supports. The results of XRD showed that there was no CeO_2-Al2O3 mixture or solid solution, indicating that CeO_2 was only loaded on the surface of Al2O3. The CeO_2/γ-Al2O3 composite support had larger specific surface area (170 m2·g-1), while for the non-loaded nanosized CeO_2, the specific surface area was small(～50 m2·g-1). The influence of impregnation and drying methods on the surface properties, thermal stability and crystal structure of composite supports was characterized by XRD, DTA and BET. The CeO_2/γ-Al2O3 composite support prepared by vacuum impregnation and microwave drying was better than that prepared by conventional impregnation and drying.展开更多
Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO...Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.展开更多
A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6...A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6-bis-[1-(2,6-dimethylphenylimino)ethyl]pyridine iron(II) dichloride(SC-A) and 1,4-bis(2,6-dimethylphenyl)- acenaphthene diimine nickel(II) dibromide(SC-B) for ethylene polymerization has been prepared by spray-drying technique using tetrahydrofuran suspension containing MgCl2, SiO2 and late-transition metal complexes. The catalysts were characterized by BET, XRD, SEM and the polymers were analyzed using GPC, DSC and 13C-NMR. The test results show that spray-drying is a very effective method for immobilizing late-transition metal catalysts for ethylene polymerization. Among six kinds of cocatalysts for olefin polymerization, TMA and TEA were confirmed to be more effective than other compounds for the ethylene polymerization system using the catalyst SC-A. For the case of the catalyst SC-B, DEAC showed the best performance as cocatalysts in ethylene polymerization. The replication of the catalyst morphology was found in the resultant polyethylene.展开更多
A diphenoxybis(β diketonato)titanium complex, (dbm) 2Ti(OPh) 2, was synthesized and the corresponding MgCl 2\|supported catalyst was prepared by impregnation method. The polymerization activity was drastically improv...A diphenoxybis(β diketonato)titanium complex, (dbm) 2Ti(OPh) 2, was synthesized and the corresponding MgCl 2\|supported catalyst was prepared by impregnation method. The polymerization activity was drastically improved by using MgCl 2\|supported (dbm) 2Ti(OPh) 2 activated by aluminoxane (MAO) for ethylene polymerization (1.5×10 5 g/molTi with the heterogeneous catalyst and 1.3×10\+3 g/molTi with the homogeneous one). When the molar ratio of Al to Ti increased from 50 to 1000, the crystallinity and molecular weight of polyethylene were decreased rapidly. Also, the molecular weight of polyethylene was decreased from 5.1×10 5 to 2.8×10\+5 by increasing the molar content of titanium of the supported catalyst from 0.5×10 -5 to 3.42 ×10 -5 . After 60 min of the reaction, the molecular weight was at 5.0×10 5 or so. It is revealed that the MgCl 2\|supported β diketonato titanium complex is influenced by the polymerization conditions markedly.展开更多
HZSM-5, Al_2O_3, TiO_2 and SiO_2 supported CeO_2-ZrO_2-CrO_x catalysts were prepared by deposition-precipitation method and tested for deep catalytic oxidation of 1,2-dichloroethane（DCE）, as one of the common chlori...HZSM-5, Al_2O_3, TiO_2 and SiO_2 supported CeO_2-ZrO_2-CrO_x catalysts were prepared by deposition-precipitation method and tested for deep catalytic oxidation of 1,2-dichloroethane（DCE）, as one of the common chlorinated organic pollutants. All the catalysts were characterized by means of N_2 adsorption-desorption, X-ray photoelectron spectroscopy（XPS）, ammonia-temperatureprogrammed desorption（NH_3-TPD） and hydrogen temperature-programmed reduction（H2-TPR）. The characterization results revealed that there was strongly synergistic effect between the oxidizability of CZCr species and the acidity of supports, which obviously promoted the catalytic activity for DCE degradation. 20% CZCr/HZSM-5 showed the highest activity and good durability during the long-term continuous test. The catalytic activity decreased in the order： 20%CZCr/HZSM-5〉CZCr〉20%CZCr/TiO_2〉20%CZCr/Al_2O_3〉20%CZCr/SiO_2.展开更多
基金Project supported by the Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center,ChinaProject(51205417)supported by the National Natural Science Foundation of China
文摘A SiC/ZrSiO4？SiO2 （SZS） coating was successfully fabricated on the carbon/carbon （C/C） composites by pack cementation, slurry painting and sintering to improve the anti-oxidation property and thermal shock resistance. The anti-oxidation properties under different oxygen partial pressures （OPP） and thermal shock resistance of the SZS coating were investigated. The results show that the SZS coated sample under low OPP, corresponding to the ambient air, during isothermal oxidation was 0.54% in mass gain after 111 h oxidation at 1500 ° C and less than 0.03% in mass loss after 50 h oxidation in high OPP, corresponding to the air flow rate of 36 L/h. Additionally, the residual compressive strengths （RCS） of the SZS coated samples after oxidation for 50 h in high OPP and 80 h in low OPP remain about 70% and 72.5% of those of original C/C samples, respectively. Moreover, the mass loss of SZS coated samples subjected to the thermal cycle from 1500 ° C in high OPP to boiling water for 30 times was merely 1.61%.
基金Supported by the National Basic Research Program of China （2009CB623406）, the National Natural Science Foundation of China （20990222） and the Natural Science Foundation of Jiangsu Province （BK2009021, SBK200930313）.
文摘Composite membranes have attracted increasing attentions owing to their potential applications for CO2 separation. In this work, ceramic supported polydimethylsiloxane （PDMS） and poly （ethylene glycol） diacrylate （PEGDA） composite membranes were prepared. The microstructure and physicochemical properties of the compos- ite membranes were characterized. Preparation conditions were systematically optimized. The gas separation performance of the as-prepared membranes was studied by pure gas and binary gas permeation measurement of CO〉 N2 and H〉 Experiments showed that PDMS, as silicone rubber, exhibited larger permeance and lower separation factors. Conversely, PEGDA composite membrane presented smaller gas permeance but higher ideal selectivity for CO2/N2. Compared to the performance of those membranes using polymeric supports or freestanding membranes, the two kinds of ceramic supported composite membranes exhibited higher gas permeance and acceptable selectivity. Therefore, the ceramic supported composite membrane can be expected as a candidate for CO2 separation from light gases.
基金Project(HIT.NSRIF.2010112)supported by the Fundamental Research Fund for the Central Universities,ChinaProjects(50902030,51021002)supported by the National Natural Science Foundation of China
文摘BNp/Al2O3-SiO2 system ceramic matrix composites with different volume fractions （10%-60%） of hexagonal BN particulates （BNp） were prepared by hot-press sintering technique. Phase components, microstructure, mechanical properties and plasma erosion resistance were also investigated. With the increase of h-BNp content, relative density and Vickers＇ hardness of the composite ceramics decrease, while the flexural strength, elastic modulus and fracture toughness increase and then decrease. The plasma erosion resistance linearly deteriorated with the increase of BNp content which is mainly determined by the density, crystal structure and atomic number of the elements.
文摘Based on the γ-Al2O3 support with large-size pores, impregnation-deposition method was adopted to prepare the nano CeO_2/γ-Al2O3 composite supports. The results of XRD showed that there was no CeO_2-Al2O3 mixture or solid solution, indicating that CeO_2 was only loaded on the surface of Al2O3. The CeO_2/γ-Al2O3 composite support had larger specific surface area (170 m2·g-1), while for the non-loaded nanosized CeO_2, the specific surface area was small(～50 m2·g-1). The influence of impregnation and drying methods on the surface properties, thermal stability and crystal structure of composite supports was characterized by XRD, DTA and BET. The CeO_2/γ-Al2O3 composite support prepared by vacuum impregnation and microwave drying was better than that prepared by conventional impregnation and drying.
文摘Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.
基金supported by the National Natural Science Foundation of China (Grant No.U1162114)the Science Foundation of Tianjin University of Science & Technology (20090420)
文摘A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6-bis-[1-(2,6-dimethylphenylimino)ethyl]pyridine iron(II) dichloride(SC-A) and 1,4-bis(2,6-dimethylphenyl)- acenaphthene diimine nickel(II) dibromide(SC-B) for ethylene polymerization has been prepared by spray-drying technique using tetrahydrofuran suspension containing MgCl2, SiO2 and late-transition metal complexes. The catalysts were characterized by BET, XRD, SEM and the polymers were analyzed using GPC, DSC and 13C-NMR. The test results show that spray-drying is a very effective method for immobilizing late-transition metal catalysts for ethylene polymerization. Among six kinds of cocatalysts for olefin polymerization, TMA and TEA were confirmed to be more effective than other compounds for the ethylene polymerization system using the catalyst SC-A. For the case of the catalyst SC-B, DEAC showed the best performance as cocatalysts in ethylene polymerization. The replication of the catalyst morphology was found in the resultant polyethylene.
文摘A diphenoxybis(β diketonato)titanium complex, (dbm) 2Ti(OPh) 2, was synthesized and the corresponding MgCl 2\|supported catalyst was prepared by impregnation method. The polymerization activity was drastically improved by using MgCl 2\|supported (dbm) 2Ti(OPh) 2 activated by aluminoxane (MAO) for ethylene polymerization (1.5×10 5 g/molTi with the heterogeneous catalyst and 1.3×10\+3 g/molTi with the homogeneous one). When the molar ratio of Al to Ti increased from 50 to 1000, the crystallinity and molecular weight of polyethylene were decreased rapidly. Also, the molecular weight of polyethylene was decreased from 5.1×10 5 to 2.8×10\+5 by increasing the molar content of titanium of the supported catalyst from 0.5×10 -5 to 3.42 ×10 -5 . After 60 min of the reaction, the molecular weight was at 5.0×10 5 or so. It is revealed that the MgCl 2\|supported β diketonato titanium complex is influenced by the polymerization conditions markedly.
基金Project supports from National Nature Science Foundation of China(21177110)
文摘HZSM-5, Al_2O_3, TiO_2 and SiO_2 supported CeO_2-ZrO_2-CrO_x catalysts were prepared by deposition-precipitation method and tested for deep catalytic oxidation of 1,2-dichloroethane（DCE）, as one of the common chlorinated organic pollutants. All the catalysts were characterized by means of N_2 adsorption-desorption, X-ray photoelectron spectroscopy（XPS）, ammonia-temperatureprogrammed desorption（NH_3-TPD） and hydrogen temperature-programmed reduction（H2-TPR）. The characterization results revealed that there was strongly synergistic effect between the oxidizability of CZCr species and the acidity of supports, which obviously promoted the catalytic activity for DCE degradation. 20% CZCr/HZSM-5 showed the highest activity and good durability during the long-term continuous test. The catalytic activity decreased in the order： 20%CZCr/HZSM-5〉CZCr〉20%CZCr/TiO_2〉20%CZCr/Al_2O_3〉20%CZCr/SiO_2.
