Cold-rolling workability, heat treatment characteristics and mechanical properties of Mg-5%-22%Li-2%Zn(mass fraction) wrought alloys were studied. Density of alloys is between 1.19 and 1.62 g/cm^3. The limit of reduct...Cold-rolling workability, heat treatment characteristics and mechanical properties of Mg-5%-22%Li-2%Zn(mass fraction) wrought alloys were studied. Density of alloys is between 1.19 and 1.62 g/cm^3. The limit of reduction for cold rolling of the β phase alloys at 16% and 22%Li exceeds 90% at room temperature. The properties and microstructures of Mg-Li-Zn alloys were studied, which were homogenized, cold rolled, then annealed at different temperatures. Recrystallization behaviors of the alloys were investigated through microstructures observing and hardness measuring. The results show that the cast billets are suitable for rolling after homogenization at 573K for 12 h for Mg-9Li-2Zn-2Ca alloy and at 523K for 24 h for Mg-9Li-2Zn-2Ca alloy. The cold rolled plates were completely recrystallizated by annealing at 573K for 1 h.展开更多
The microstructure and mechanical properties of as-cast Al−Cu−Li−Mg−Zn alloys fabricated by conventional gravity casting and centrifugal casting techniques combined with rapid solidification were investigated.Experime...The microstructure and mechanical properties of as-cast Al−Cu−Li−Mg−Zn alloys fabricated by conventional gravity casting and centrifugal casting techniques combined with rapid solidification were investigated.Experimental results demonstrated that compared with the gravity casting technique,the water-cooling centrifugal casting technique significantly reduces porosity,refinesα(Al)grains and secondary phases,modifies the morphology of secondary phases,and mitigates both macro-and micro-segregation.These improvements arise from the synergistic effects of the vigorous backflow,centrifugal field,vibration and rapid solidification.Porosity and coarse plate-like Al13Fe4/Al7Cu2Fe phase result in the fracture before the gravity-cast alloy reaches the yield point.The centrifugal-cast alloy,however,exhibits an ultra-high yield strength of 292.0 MPa and a moderate elongation of 6.1%.This high yield strength is attributed to solid solution strengthening(SSS)of 225.3 MPa,and grain boundary strengthening(GBS)of 35.7 MPa.Li contributes the most to SSS with a scaling factor of 7.9 MPa·wt.%^(-1).The elongation of the centrifugal-cast alloy can be effectively enhanced by reducing the porosity and segregation behavior,refining the microstructure and changing the morphology of secondary phases.展开更多
Mg-9wt%Li-2wt%Zn alloy was prepared and studied in this article. The addition of Ca to the alloy from 0.1wt% to 1wt% can refine the α-Mg and the best effect of refinement occurs when Ca content is 0.4wt%-0.5wt%. The ...Mg-9wt%Li-2wt%Zn alloy was prepared and studied in this article. The addition of Ca to the alloy from 0.1wt% to 1wt% can refine the α-Mg and the best effect of refinement occurs when Ca content is 0.4wt%-0.5wt%. The billets can be rolled to thin sheets at room temperature, from which it is obvious that the addition of Ca improves alloys ormalin. while it decreases with the excess addition of Ca. The results also show that the ultimate tensile strength （UTS） and yield strength （YS） of the alloy with lwt% Ca may rise by 28% and 25%, respectively, however, the elongation decreases. It is clarified that the adsorption of proper Ca on the grain boundaries refines α-Mg and improves the tensile properties, but the presence of excess Ca and stable Ca2Mg6Zn3phase worsens the elongation.展开更多
The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experimen...The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experiment, Mg-5Li-2Zn, Mg-9Li-2Zn, Mg-16Li-2Zn, Mg-22Li-2Zn, Mg-5Li-2Zn-2Ca, Mg-9Li-2Zn-2Ca, Mg-16Li-2Zn-2Ca, and Mg-22Li-2Zn-2Ca （wt%） were melted. During the melting process, the flux, which was composed of lithium chloride （LiCl） and lithium fluoride （LiF） in the proportion of 3：1 （mass ratio） and argon gas were used to protect the alloys from oxidation. The microstructure, mechanical properties, and cold-rolling workability of the wrought alloys were studied. The crystal grain of the alloys （adding Ga） is fine . The hardness of the studied alloys decreases with an increase in element Li. The density of the studied alloys is in the range of 1.187 to 1.617 g/cm^3. The reduction of the Mg-16Li-2Zn and Mg-22Li-2Zn alloys can exceed 85% at room temperature. The Mg-9Li-2Zn-2Ca alloy was heat treated at 300℃ for 8, 12, 16, and 24 h, respectively. The optimum heat treatment of the Mg-9Li-2Zn-2Ca alloy is 300℃×12h by metallographic observation and by studying the mechanical properties of the alloys.展开更多
The as-cast Mg-8 Li-xZn-yGd(x=1 2, 3,4;y=1,2;wt.%)alloys were prepared in a vacuum induction furnace and their microstructure and mechanical properties were investigated. The results show that the increase of Zn conte...The as-cast Mg-8 Li-xZn-yGd(x=1 2, 3,4;y=1,2;wt.%)alloys were prepared in a vacuum induction furnace and their microstructure and mechanical properties were investigated. The results show that the increase of Zn content results in the volume fraction of W-phase(Mg3 Zn3 Gd2) increasing while that of Mg3 Gd phase decreasing. The strength of Mg-8 Li-xZn-1 Gd alloys is improved with the increase of Zn content,which is ascribed to the second phase strengthening of fine strip-like W-phase and the solid solution strengthening of Zn element.For Mg-8 Li-4 Zn-yGd alloys,the increase of Gd content leads to the appearance of coarse and discontinuous net-like W-phase, which decreases the strength. The Mg-8 Li-4 Zn-1 Gd alloy exhibits an optimum comprehensive performance with the yield strength, ultimate tensile strength and elongation of 154.7 MPa, 197.0 MPa and 12.4%, respectively. In addition,the aging behavior of the typical alloys was also investigated.展开更多
基金Project supported by National High Tech Research Programof China (2001AA335010)
文摘Cold-rolling workability, heat treatment characteristics and mechanical properties of Mg-5%-22%Li-2%Zn(mass fraction) wrought alloys were studied. Density of alloys is between 1.19 and 1.62 g/cm^3. The limit of reduction for cold rolling of the β phase alloys at 16% and 22%Li exceeds 90% at room temperature. The properties and microstructures of Mg-Li-Zn alloys were studied, which were homogenized, cold rolled, then annealed at different temperatures. Recrystallization behaviors of the alloys were investigated through microstructures observing and hardness measuring. The results show that the cast billets are suitable for rolling after homogenization at 573K for 12 h for Mg-9Li-2Zn-2Ca alloy and at 523K for 24 h for Mg-9Li-2Zn-2Ca alloy. The cold rolled plates were completely recrystallizated by annealing at 573K for 1 h.
基金financially supported by the Natural Science Foundation of Ningbo,China (No.2023J053)。
文摘The microstructure and mechanical properties of as-cast Al−Cu−Li−Mg−Zn alloys fabricated by conventional gravity casting and centrifugal casting techniques combined with rapid solidification were investigated.Experimental results demonstrated that compared with the gravity casting technique,the water-cooling centrifugal casting technique significantly reduces porosity,refinesα(Al)grains and secondary phases,modifies the morphology of secondary phases,and mitigates both macro-and micro-segregation.These improvements arise from the synergistic effects of the vigorous backflow,centrifugal field,vibration and rapid solidification.Porosity and coarse plate-like Al13Fe4/Al7Cu2Fe phase result in the fracture before the gravity-cast alloy reaches the yield point.The centrifugal-cast alloy,however,exhibits an ultra-high yield strength of 292.0 MPa and a moderate elongation of 6.1%.This high yield strength is attributed to solid solution strengthening(SSS)of 225.3 MPa,and grain boundary strengthening(GBS)of 35.7 MPa.Li contributes the most to SSS with a scaling factor of 7.9 MPa·wt.%^(-1).The elongation of the centrifugal-cast alloy can be effectively enhanced by reducing the porosity and segregation behavior,refining the microstructure and changing the morphology of secondary phases.
文摘Mg-9wt%Li-2wt%Zn alloy was prepared and studied in this article. The addition of Ca to the alloy from 0.1wt% to 1wt% can refine the α-Mg and the best effect of refinement occurs when Ca content is 0.4wt%-0.5wt%. The billets can be rolled to thin sheets at room temperature, from which it is obvious that the addition of Ca improves alloys ormalin. while it decreases with the excess addition of Ca. The results also show that the ultimate tensile strength （UTS） and yield strength （YS） of the alloy with lwt% Ca may rise by 28% and 25%, respectively, however, the elongation decreases. It is clarified that the adsorption of proper Ca on the grain boundaries refines α-Mg and improves the tensile properties, but the presence of excess Ca and stable Ca2Mg6Zn3phase worsens the elongation.
文摘The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experiment, Mg-5Li-2Zn, Mg-9Li-2Zn, Mg-16Li-2Zn, Mg-22Li-2Zn, Mg-5Li-2Zn-2Ca, Mg-9Li-2Zn-2Ca, Mg-16Li-2Zn-2Ca, and Mg-22Li-2Zn-2Ca （wt%） were melted. During the melting process, the flux, which was composed of lithium chloride （LiCl） and lithium fluoride （LiF） in the proportion of 3：1 （mass ratio） and argon gas were used to protect the alloys from oxidation. The microstructure, mechanical properties, and cold-rolling workability of the wrought alloys were studied. The crystal grain of the alloys （adding Ga） is fine . The hardness of the studied alloys decreases with an increase in element Li. The density of the studied alloys is in the range of 1.187 to 1.617 g/cm^3. The reduction of the Mg-16Li-2Zn and Mg-22Li-2Zn alloys can exceed 85% at room temperature. The Mg-9Li-2Zn-2Ca alloy was heat treated at 300℃ for 8, 12, 16, and 24 h, respectively. The optimum heat treatment of the Mg-9Li-2Zn-2Ca alloy is 300℃×12h by metallographic observation and by studying the mechanical properties of the alloys.
基金Project(2016YFB0301004)supported by the National Key Research and Development Program of ChinaProject(51771115)supported by the National Natural Science Foundation of China+3 种基金Project(6141B06310106)supported by the Joint Fund for Space Science and Technology,ChinaProject(009-031-001)supported by the Science and Technology Innovation Program,ChinaProject(USCAST2016-18)supported by the Research Program of Joint Research Center of Advanced Spaceflight Technologies,ChinaProject(SAST2016048)supported by the Science Innovation Foundation of Shanghai Academy of Spaceflight Technology,China
文摘The as-cast Mg-8 Li-xZn-yGd(x=1 2, 3,4;y=1,2;wt.%)alloys were prepared in a vacuum induction furnace and their microstructure and mechanical properties were investigated. The results show that the increase of Zn content results in the volume fraction of W-phase(Mg3 Zn3 Gd2) increasing while that of Mg3 Gd phase decreasing. The strength of Mg-8 Li-xZn-1 Gd alloys is improved with the increase of Zn content,which is ascribed to the second phase strengthening of fine strip-like W-phase and the solid solution strengthening of Zn element.For Mg-8 Li-4 Zn-yGd alloys,the increase of Gd content leads to the appearance of coarse and discontinuous net-like W-phase, which decreases the strength. The Mg-8 Li-4 Zn-1 Gd alloy exhibits an optimum comprehensive performance with the yield strength, ultimate tensile strength and elongation of 154.7 MPa, 197.0 MPa and 12.4%, respectively. In addition,the aging behavior of the typical alloys was also investigated.
