The existing research of the flatness control for strip cold rolling mainly focuses on the calculation of the optimum adjustment of individual flatness actuator in accordance with the flatness deviation, which can be ...The existing research of the flatness control for strip cold rolling mainly focuses on the calculation of the optimum adjustment of individual flatness actuator in accordance with the flatness deviation, which can be used for general flatness control. However, it does not work for some special rolling processes, such as the elimination of ultra single side edge-waves and the prevention of strip break due to tilting roll control overshooting. For the purpose of solving these problems, the influences of non-symmetrical work roll bending and intermediate roll bending on flatness control were analyzed by studying efficiencies of them. Moreover, impacts of two kinds of non-symmetrical roll bending control on the pressure distribution between rolls were studied theoretically. A non-symmetrical work roll bending model was developed by theoretical analysis in accordance with practical conditions. The model was applied to the revamp of a 1250 6-H reversible universal crown mill (UCM) cold mill. Theoretical study and practical applications show that the coordination utilization of the non-symmetrical work roll bending control and tilting roll control was effective in flatness control when there appeared bad strip single side edge waves, especially when the incoming strip was with a wedge shape. In addition, the risk of strip break due to tilting control overshooting could be reduced. Furthermore, the non-symmetrical roll bending control can reduce the extent of uneven distribution of pressure between rolls caused by intermediate roll shifting in flatness control and slow down roll wear. The non-symmetrical roll bending control technology has important theoretical and practical significance to better flatness control.展开更多
A study on roll gap profile (strip profile) control was accomplished in a1700 mm single-stand temper mill. Some critical problems such as the deviation of work roll contourcaused by grinding and wear, the effectivenes...A study on roll gap profile (strip profile) control was accomplished in a1700 mm single-stand temper mill. Some critical problems such as the deviation of work roll contourcaused by grinding and wear, the effectiveness of work roll bending were discussed. Using a finiteelement model, the effects of roll contours (ground and wear) on strip profile were investigated.The roll bending effect on strip thickness was also analyzed. It is pointed out that there are somespecial features of flatness control in the temper mill: during temper rolling, roll deformation isslight due to small rolling load, and the loaded roll gap profile mainly depends on work rollcontour, while the backup roll has a little effect on gap crown; the effect of bending force ongauge can not be ignored due to the coupling between flatness control and gauge control. A new rollcontour arrangement adaptable to the mill was presented and has been put into practical production.The application of the new set of rolls showed some good results: larger crown control range of workroll bender, higher rolling stability, better strip profile and flatness quality.展开更多
The pearlitic transformation and the deformation behavior of lamellar cementite after cold rolling in eutectoid steels Fe-0.76%C-0.137%Mn(mass fraction) were studied by means of Formastor-F (Full Automatic Transformat...The pearlitic transformation and the deformation behavior of lamellar cementite after cold rolling in eutectoid steels Fe-0.76%C-0.137%Mn(mass fraction) were studied by means of Formastor-F (Full Automatic Transformation Testing Instrument) and field emission scanning electronic microscopy (FESEM) observation. Fine and coarse pearlite were obtained in the eutectoid steels austenitized at 900℃ for 15min, then hold at 620℃ for 90 s and 690℃ for 7 h, respectively. The deformation behavior of cold rolled lamellar cementite could be classified as: cleavage fracture, inhomogeneous slip, fragmentation, thinning or necking, and homogeneous bending. The cementite lamellae with the thickness of more than 100 nm could be deformed plastically.展开更多
304 stainless steel coating was deposited on the Interstitial-Free steel substrate by cold gas dynamic spraying （CGDS）. Three-point bending test of the cold sprayed 304 stainless steel coating was tested by SHIMADZU...304 stainless steel coating was deposited on the Interstitial-Free steel substrate by cold gas dynamic spraying （CGDS）. Three-point bending test of the cold sprayed 304 stainless steel coating was tested by SHIMADZU electro-hydraulic servo-controlled fatigue testing machine and the fracture morphology was examined by scanning electron microscopy. The results showed that the fracture behavior of the cold sprayed 304 stainless steel coating was brittleness fracture. The crack in the coating occurred in the interfaces between particles and the crack extended to the internal of the coating with the increase of the load. When the crack has extended to the combination interface between coating and substrate, the crack extended to the two sides. The microstructure and mechanical property of the cold sprayed 304 stainless steel coating have been optimized after heat treatment.展开更多
基金supported by National Natural Science Foundation of China (Grant No. 50534020)
文摘The existing research of the flatness control for strip cold rolling mainly focuses on the calculation of the optimum adjustment of individual flatness actuator in accordance with the flatness deviation, which can be used for general flatness control. However, it does not work for some special rolling processes, such as the elimination of ultra single side edge-waves and the prevention of strip break due to tilting roll control overshooting. For the purpose of solving these problems, the influences of non-symmetrical work roll bending and intermediate roll bending on flatness control were analyzed by studying efficiencies of them. Moreover, impacts of two kinds of non-symmetrical roll bending control on the pressure distribution between rolls were studied theoretically. A non-symmetrical work roll bending model was developed by theoretical analysis in accordance with practical conditions. The model was applied to the revamp of a 1250 6-H reversible universal crown mill (UCM) cold mill. Theoretical study and practical applications show that the coordination utilization of the non-symmetrical work roll bending control and tilting roll control was effective in flatness control when there appeared bad strip single side edge waves, especially when the incoming strip was with a wedge shape. In addition, the risk of strip break due to tilting control overshooting could be reduced. Furthermore, the non-symmetrical roll bending control can reduce the extent of uneven distribution of pressure between rolls caused by intermediate roll shifting in flatness control and slow down roll wear. The non-symmetrical roll bending control technology has important theoretical and practical significance to better flatness control.
文摘A study on roll gap profile (strip profile) control was accomplished in a1700 mm single-stand temper mill. Some critical problems such as the deviation of work roll contourcaused by grinding and wear, the effectiveness of work roll bending were discussed. Using a finiteelement model, the effects of roll contours (ground and wear) on strip profile were investigated.The roll bending effect on strip thickness was also analyzed. It is pointed out that there are somespecial features of flatness control in the temper mill: during temper rolling, roll deformation isslight due to small rolling load, and the loaded roll gap profile mainly depends on work rollcontour, while the backup roll has a little effect on gap crown; the effect of bending force ongauge can not be ignored due to the coupling between flatness control and gauge control. A new rollcontour arrangement adaptable to the mill was presented and has been put into practical production.The application of the new set of rolls showed some good results: larger crown control range of workroll bender, higher rolling stability, better strip profile and flatness quality.
文摘The pearlitic transformation and the deformation behavior of lamellar cementite after cold rolling in eutectoid steels Fe-0.76%C-0.137%Mn(mass fraction) were studied by means of Formastor-F (Full Automatic Transformation Testing Instrument) and field emission scanning electronic microscopy (FESEM) observation. Fine and coarse pearlite were obtained in the eutectoid steels austenitized at 900℃ for 15min, then hold at 620℃ for 90 s and 690℃ for 7 h, respectively. The deformation behavior of cold rolled lamellar cementite could be classified as: cleavage fracture, inhomogeneous slip, fragmentation, thinning or necking, and homogeneous bending. The cementite lamellae with the thickness of more than 100 nm could be deformed plastically.
基金the support of the BaoShan Iron and Steel Company Limited
文摘304 stainless steel coating was deposited on the Interstitial-Free steel substrate by cold gas dynamic spraying （CGDS）. Three-point bending test of the cold sprayed 304 stainless steel coating was tested by SHIMADZU electro-hydraulic servo-controlled fatigue testing machine and the fracture morphology was examined by scanning electron microscopy. The results showed that the fracture behavior of the cold sprayed 304 stainless steel coating was brittleness fracture. The crack in the coating occurred in the interfaces between particles and the crack extended to the internal of the coating with the increase of the load. When the crack has extended to the combination interface between coating and substrate, the crack extended to the two sides. The microstructure and mechanical property of the cold sprayed 304 stainless steel coating have been optimized after heat treatment.
