According to the ion and molecule coexistence theory, the activity model of Al2O3- BaO-B2O3 ternary slag system was established, and the influences of BaO/Al2O3 molar ratio, B2O3 mole fraction and temperature on the a...According to the ion and molecule coexistence theory, the activity model of Al2O3- BaO-B2O3 ternary slag system was established, and the influences of BaO/Al2O3 molar ratio, B2O3 mole fraction and temperature on the activity of the slag system were investigated. Finally, the equal activity curves were drawn with the model results. The results show that with the increase of BaO/Al2O3 ratio, the activity of Al2O3 is significantly reduced, the activi- ty of BaO3-Al2O3 is increased obviously, and the activity of 2Al2O3· B2O3 is also decreased. With the increase of B2O3 mole fraction, the activity of BaO · Al2O3 decreased significantly, while the activities of BaO·B2O3 and 2Al2O3·B2O3 increased. In addition, the influence of temperature on the activities of different components is com paratively smaller than the influence of BaO/Al2O3 ratio and B2O3 mole fraction.展开更多
Among new low-melting-point glasses, bismuth ate glass is deemed to have the most potential as an environmentally friendly replacement for polluting Pb-containing glasses. Current studies of boro-bismuthate glasses fo...Among new low-melting-point glasses, bismuth ate glass is deemed to have the most potential as an environmentally friendly replacement for polluting Pb-containing glasses. Current studies of boro-bismuthate glasses focus on the structural influence of the additional oxide in the context of low-melting-point electronic sealing applications. In this study, the structure of quaternary Bi2O3- ZnO-B2O3-BaO glasses was investigated spectroscopic ally, with Fourier-transform-infrared (FT-IR) and Raman spectra recorded for glasses with different main oxide contents. Signals in the FT-IR are mainly observed around 500 cm﹣1, 720 cm﹣1, 840 cm﹣1, 980 - 1080 cm﹣1, and 1200 - 1500 cm﹣1, while the Raman scattering peaks are located at 130 cm﹣1, 390 cm﹣1, 575 cm﹣1, 920 cm﹣1, and 1250 cm﹣1. The glasses are mainly structured around [BO3] units and the numbers of [BiO6] and [BiO3] units increase with the Bi2O3 content increasing. Concurrently, the FT-IR absorption peaks associated with [BO4] units shift to lower wave numbers, indicating a loosening of the glass structure. However, as the B2O3 content is increased, the numbers of [BO3] and [BO4] units increase, while those of [BiO3] and [BiO6] units decrease, highlighting a densification of the glass structure. ZnO acts as a network modifier in these glasses.展开更多
B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass with different Al_2O_3 contents（1mol%, 3mol%, 5mol%, and 7mol%） was prepared, and it was intended to be used as lead-free and low-melting glass sealants for solid oxide fuel cells....B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass with different Al_2O_3 contents（1mol%, 3mol%, 5mol%, and 7mol%） was prepared, and it was intended to be used as lead-free and low-melting glass sealants for solid oxide fuel cells. The effects of Al_2O_3 content on the structures, thermal properties, and sintering behaviors of the B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass were investigated in detail. The Al_2O_3 content largely influenced the structures and thermal properties of the glass. When the Al_2O_3 content 5mol%, the transition temperature of the glass decreased with the Al_2O_3 content, while the crystallization temperature increased with the Al_2O_3 content. However, higher Al_2O_3 content degraded the stability of the glass. The B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass with 5 mol% Al_2O_3 content exhibits the optimal sintering densification characteristics and can be used as glass sealants for solid oxide fuel cells.展开更多
The effect of ZnO-B2O3（ZB） glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd2O3-TiO2-Bi2O3 （BNTB） system was investigated with the aid of X-ray diffraction, sc...The effect of ZnO-B2O3（ZB） glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd2O3-TiO2-Bi2O3 （BNTB） system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 ℃. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ε=74, tan δ=4×10^-4, and TCC=25 ppm/℃ were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 ℃ for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.展开更多
A series of BaO-La2O3-B2O3(BLB) glass coats on the Ti-based alloy substrates were developed at different temperatures for different times. The BLB glasses were analyzed by differential thermal analysis(DTA) and therma...A series of BaO-La2O3-B2O3(BLB) glass coats on the Ti-based alloy substrates were developed at different temperatures for different times. The BLB glasses were analyzed by differential thermal analysis(DTA) and thermal mechanical analysis(TMA) to determine the crystallization temperature and coefficients of thermal expansion(CETs) of the glass. The tensile strength and microstructure of the glass coats were analyzed and the effects of the coating condition on the tensile strength and microstructure were discussed. The results show that the CETs of the borate glass at different temperatures match with those of Ti-based alloy,and the difference between the borate glass and Ti-based alloy at each temperature is below 5%. The spreading area in N2 atmosphere is much larger than that in air atmosphere,indicating that N2 atmosphere is helpful for the wetting of borate glass to Ti-based alloy. The tensile strength of the glass coats can reach as high as 28.42 MPa,meeting the requirements for the coat binder. With the increase of coating time,the tensile strength of coats increases firstly while then decreases. The coat prepared at 730 ℃ for 30 min is fairly smooth and complete,while the other coats contain lots of defects such as large or small uncoated region. It is believed that the coating temperature of 730 ℃ and coating time of 30 min are the proper coating conditions to prepare BLB glass coats.展开更多
BaO-La2O3-B2O3 （BLB） glass, suitable to be used as a sealing between metals, was chosen to be the binder in preparing glass coats on the Ti-alloy substrate. The SiCN nano-powder was introduced as the filler for the ...BaO-La2O3-B2O3 （BLB） glass, suitable to be used as a sealing between metals, was chosen to be the binder in preparing glass coats on the Ti-alloy substrate. The SiCN nano-powder was introduced as the filler for the absorbing coat because it is considered to be a good high temperature absorber. The effect of the coating temperature and coating time on the tensile strength of the glass coat was investigated and the proper coating parameters to get good mechanical properties were determined. In addition, the effects of the SiCN content on the tensile strength of the absorbing coat were also discussed. Results show that it is possible to prepare the glass coat using the BLB glass as a binder. That the coat formed at 730℃ for 30 min has the best tensile strength witnesses 730 ℃, 30 min to be the proper parameter to prepare the glass coat. The BLB glass coat without SiCN powder possesses good tensile strength and the introduction of the SiCN absorber into the glass coat will lower the tensile strength. As the SiCN content increases, the tensile strength of the absorbing coat decreases, which could be attributed to the aggregation of SiCN in the coats.展开更多
文摘According to the ion and molecule coexistence theory, the activity model of Al2O3- BaO-B2O3 ternary slag system was established, and the influences of BaO/Al2O3 molar ratio, B2O3 mole fraction and temperature on the activity of the slag system were investigated. Finally, the equal activity curves were drawn with the model results. The results show that with the increase of BaO/Al2O3 ratio, the activity of Al2O3 is significantly reduced, the activi- ty of BaO3-Al2O3 is increased obviously, and the activity of 2Al2O3· B2O3 is also decreased. With the increase of B2O3 mole fraction, the activity of BaO · Al2O3 decreased significantly, while the activities of BaO·B2O3 and 2Al2O3·B2O3 increased. In addition, the influence of temperature on the activities of different components is com paratively smaller than the influence of BaO/Al2O3 ratio and B2O3 mole fraction.
文摘Among new low-melting-point glasses, bismuth ate glass is deemed to have the most potential as an environmentally friendly replacement for polluting Pb-containing glasses. Current studies of boro-bismuthate glasses focus on the structural influence of the additional oxide in the context of low-melting-point electronic sealing applications. In this study, the structure of quaternary Bi2O3- ZnO-B2O3-BaO glasses was investigated spectroscopic ally, with Fourier-transform-infrared (FT-IR) and Raman spectra recorded for glasses with different main oxide contents. Signals in the FT-IR are mainly observed around 500 cm﹣1, 720 cm﹣1, 840 cm﹣1, 980 - 1080 cm﹣1, and 1200 - 1500 cm﹣1, while the Raman scattering peaks are located at 130 cm﹣1, 390 cm﹣1, 575 cm﹣1, 920 cm﹣1, and 1250 cm﹣1. The glasses are mainly structured around [BO3] units and the numbers of [BiO6] and [BiO3] units increase with the Bi2O3 content increasing. Concurrently, the FT-IR absorption peaks associated with [BO4] units shift to lower wave numbers, indicating a loosening of the glass structure. However, as the B2O3 content is increased, the numbers of [BO3] and [BO4] units increase, while those of [BiO3] and [BiO6] units decrease, highlighting a densification of the glass structure. ZnO acts as a network modifier in these glasses.
基金Funded by the Jiangxi Provincial Department of Education(KJLD13008)the National Natural Science Foundation of China(number 51362020)the Research Fund for the Doctoral Program of Higher Education(20123601110006)
文摘B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass with different Al_2O_3 contents（1mol%, 3mol%, 5mol%, and 7mol%） was prepared, and it was intended to be used as lead-free and low-melting glass sealants for solid oxide fuel cells. The effects of Al_2O_3 content on the structures, thermal properties, and sintering behaviors of the B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass were investigated in detail. The Al_2O_3 content largely influenced the structures and thermal properties of the glass. When the Al_2O_3 content 5mol%, the transition temperature of the glass decreased with the Al_2O_3 content, while the crystallization temperature increased with the Al_2O_3 content. However, higher Al_2O_3 content degraded the stability of the glass. The B_2O_3-SiO_2-ZnO-BaO-Al_2O_3 glass with 5 mol% Al_2O_3 content exhibits the optimal sintering densification characteristics and can be used as glass sealants for solid oxide fuel cells.
基金Funded by the Tianjin Natural Science Foundation of China (No.06YFJMJC01000)
文摘The effect of ZnO-B2O3（ZB） glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd2O3-TiO2-Bi2O3 （BNTB） system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 ℃. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ε=74, tan δ=4×10^-4, and TCC=25 ppm/℃ were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 ℃ for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.
基金Project(50572090) supported by the National Natural Science Foundation of China
文摘A series of BaO-La2O3-B2O3(BLB) glass coats on the Ti-based alloy substrates were developed at different temperatures for different times. The BLB glasses were analyzed by differential thermal analysis(DTA) and thermal mechanical analysis(TMA) to determine the crystallization temperature and coefficients of thermal expansion(CETs) of the glass. The tensile strength and microstructure of the glass coats were analyzed and the effects of the coating condition on the tensile strength and microstructure were discussed. The results show that the CETs of the borate glass at different temperatures match with those of Ti-based alloy,and the difference between the borate glass and Ti-based alloy at each temperature is below 5%. The spreading area in N2 atmosphere is much larger than that in air atmosphere,indicating that N2 atmosphere is helpful for the wetting of borate glass to Ti-based alloy. The tensile strength of the glass coats can reach as high as 28.42 MPa,meeting the requirements for the coat binder. With the increase of coating time,the tensile strength of coats increases firstly while then decreases. The coat prepared at 730 ℃ for 30 min is fairly smooth and complete,while the other coats contain lots of defects such as large or small uncoated region. It is believed that the coating temperature of 730 ℃ and coating time of 30 min are the proper coating conditions to prepare BLB glass coats.
文摘BaO-La2O3-B2O3 （BLB） glass, suitable to be used as a sealing between metals, was chosen to be the binder in preparing glass coats on the Ti-alloy substrate. The SiCN nano-powder was introduced as the filler for the absorbing coat because it is considered to be a good high temperature absorber. The effect of the coating temperature and coating time on the tensile strength of the glass coat was investigated and the proper coating parameters to get good mechanical properties were determined. In addition, the effects of the SiCN content on the tensile strength of the absorbing coat were also discussed. Results show that it is possible to prepare the glass coat using the BLB glass as a binder. That the coat formed at 730℃ for 30 min has the best tensile strength witnesses 730 ℃, 30 min to be the proper parameter to prepare the glass coat. The BLB glass coat without SiCN powder possesses good tensile strength and the introduction of the SiCN absorber into the glass coat will lower the tensile strength. As the SiCN content increases, the tensile strength of the absorbing coat decreases, which could be attributed to the aggregation of SiCN in the coats.
