The 2024/3003 aluminum gradient alloys are prepared by semi continuous casting. The influences of throttle bore diameter of embedded nozzle and temperature of internal melt on composition distribution, macrostructure,...The 2024/3003 aluminum gradient alloys are prepared by semi continuous casting. The influences of throttle bore diameter of embedded nozzle and temperature of internal melt on composition distribution, macrostructure, hardness are analyzed, and the stability of gradient distribution of composition, macrostructure and hardness along the axial direction of the ingot is also studied. The results show that diffe rent composition profiles can be achieved by adjusting the processing parameters; the volume fraction of inner alloy in the ingot can be increased by enlarging the throttle bore diameter and elevating the temperature of inner melt; quasi steady solidification can be realized within 20 s during cast processing, and consistent quality ingot is obtained by controlling the casting speed and liquid height of inner melt.展开更多
Ti1Al2O3 Functionally Gradient Material (FGM) was prepared by an explosive compaction/SHS process. Ten sheets of the compounding powder were laminated and pressed to get a green body of FGM. It was then compacted expl...Ti1Al2O3 Functionally Gradient Material (FGM) was prepared by an explosive compaction/SHS process. Ten sheets of the compounding powder were laminated and pressed to get a green body of FGM. It was then compacted explosively By burying the explosive compaction body into a stoichiometric Al/TiO2 mixture and igniting the combustion of the stoichiometric Al/TiO2 mixture, the SHS reaction of the explosive compaction body was initiated by the heat released from the combustion of the stoichiometric Al/TiO2 mixture. In this way, Ti/Al2O3 FGM was synthesized. The adiabatic temperatures of each gradient layer were calculated when the preheating temperatures were 298 K and 1173 K, respectively The microstructure, composition and properties of Ti/Al2O3 FGM and the reaction mechanism of each gradient layer were studied. It was found that Ti/Al2O3 FGM prepared by the explosive compaction/SHS process had a high density and a high microhardness. Its structure, composition and properties showed apparent gradient distribution. The structure of the standard stoichiometric ratio gradient layer of FGM was a network structure. Its reaction mode could be described as follows: Al powder melted first, then the molten Al penetrated into the TiO2 zone and reacted with TiO2, and big pores were left in the original positions of Al powder. The reaction of gradient layers with the addition of Al3O3 as diluents was similar to that of the standard stoichiometric ratio gradient layer, so were their structure and composition. However, the reaction of gradient layers with the addition of Ti as diluents was more complex and the composition deviated slightly from the designed one展开更多
The microstructure and mechanical properties of steel/Al structure material produced by additive manufacturing （AM） was investigated in this work based on the cold metal transfer welding. The results show that the m...The microstructure and mechanical properties of steel/Al structure material produced by additive manufacturing （AM） was investigated in this work based on the cold metal transfer welding. The results show that the microstructure gradually changed from the steel side to the aluminum side. The microstructure in the steel layer consisted of vermiform like ferrite and anstenite structure, while in the aluminum layer the microstructure was constituted by c^-A1 grains and typical reticulate distributive Al-Si eutectic structure. Besides, a 7 y.m thickness Ni-Al intermetallic compound layer was emerged at the interface of nickel and aluminum layer. The maximum room-temperature tensile strength of the Steel-Al structure materials was found to be 54 MPa, the rupture morphology showed a brittle fracture characteristic.展开更多
Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force ap...Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.展开更多
Functionally gradient samples are prepared by getting metal Ni or Cu bonded with Ni-matrix composites reinforced by TiB2 particles by field activated diffusion bonding process. The intermetallic compound of Ni3Al has ...Functionally gradient samples are prepared by getting metal Ni or Cu bonded with Ni-matrix composites reinforced by TiB2 particles by field activated diffusion bonding process. The intermetallic compound of Ni3Al has been applied as a mediate layer in order to reduce residual stress. The microstracture, phase composition of the interfaces between the metal and Ni3Al are determined and the mechanical properties of the gradient materials are characterized. Elemental concentration profiles across the interfaces between layers showed significant diffusion dissolution and formation of firm bonds. Measured micro-hardness values of the sample increased monotonically from the metal substrate to the surface layer of composites. The values for the surface composite layer ranged from about 2 000 HK to 3 300 HK. The results of this investigation demonstrate the feasibility of field activated diffusion bonding process for rapid preparation of FGMs.展开更多
文摘The 2024/3003 aluminum gradient alloys are prepared by semi continuous casting. The influences of throttle bore diameter of embedded nozzle and temperature of internal melt on composition distribution, macrostructure, hardness are analyzed, and the stability of gradient distribution of composition, macrostructure and hardness along the axial direction of the ingot is also studied. The results show that diffe rent composition profiles can be achieved by adjusting the processing parameters; the volume fraction of inner alloy in the ingot can be increased by enlarging the throttle bore diameter and elevating the temperature of inner melt; quasi steady solidification can be realized within 20 s during cast processing, and consistent quality ingot is obtained by controlling the casting speed and liquid height of inner melt.
文摘Ti1Al2O3 Functionally Gradient Material (FGM) was prepared by an explosive compaction/SHS process. Ten sheets of the compounding powder were laminated and pressed to get a green body of FGM. It was then compacted explosively By burying the explosive compaction body into a stoichiometric Al/TiO2 mixture and igniting the combustion of the stoichiometric Al/TiO2 mixture, the SHS reaction of the explosive compaction body was initiated by the heat released from the combustion of the stoichiometric Al/TiO2 mixture. In this way, Ti/Al2O3 FGM was synthesized. The adiabatic temperatures of each gradient layer were calculated when the preheating temperatures were 298 K and 1173 K, respectively The microstructure, composition and properties of Ti/Al2O3 FGM and the reaction mechanism of each gradient layer were studied. It was found that Ti/Al2O3 FGM prepared by the explosive compaction/SHS process had a high density and a high microhardness. Its structure, composition and properties showed apparent gradient distribution. The structure of the standard stoichiometric ratio gradient layer of FGM was a network structure. Its reaction mode could be described as follows: Al powder melted first, then the molten Al penetrated into the TiO2 zone and reacted with TiO2, and big pores were left in the original positions of Al powder. The reaction of gradient layers with the addition of Al3O3 as diluents was similar to that of the standard stoichiometric ratio gradient layer, so were their structure and composition. However, the reaction of gradient layers with the addition of Ti as diluents was more complex and the composition deviated slightly from the designed one
基金supported by the National Natural Science Foundation of China(Grant No.51475104,51435004)the National Basic Research Program of China(2013CB035500)
文摘The microstructure and mechanical properties of steel/Al structure material produced by additive manufacturing （AM） was investigated in this work based on the cold metal transfer welding. The results show that the microstructure gradually changed from the steel side to the aluminum side. The microstructure in the steel layer consisted of vermiform like ferrite and anstenite structure, while in the aluminum layer the microstructure was constituted by c^-A1 grains and typical reticulate distributive Al-Si eutectic structure. Besides, a 7 y.m thickness Ni-Al intermetallic compound layer was emerged at the interface of nickel and aluminum layer. The maximum room-temperature tensile strength of the Steel-Al structure materials was found to be 54 MPa, the rupture morphology showed a brittle fracture characteristic.
基金supported by the National Natural Science Foundation of China(Grant No.50001008)the China Postdoctoral Science Foundation.
文摘Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.
基金Acknowledgment The authors wish to thank the financial support for this research from the National Natural Science Foundation of China （Grant No. 50975190） and the Army Office of Research （ZAM）.
文摘Functionally gradient samples are prepared by getting metal Ni or Cu bonded with Ni-matrix composites reinforced by TiB2 particles by field activated diffusion bonding process. The intermetallic compound of Ni3Al has been applied as a mediate layer in order to reduce residual stress. The microstracture, phase composition of the interfaces between the metal and Ni3Al are determined and the mechanical properties of the gradient materials are characterized. Elemental concentration profiles across the interfaces between layers showed significant diffusion dissolution and formation of firm bonds. Measured micro-hardness values of the sample increased monotonically from the metal substrate to the surface layer of composites. The values for the surface composite layer ranged from about 2 000 HK to 3 300 HK. The results of this investigation demonstrate the feasibility of field activated diffusion bonding process for rapid preparation of FGMs.
