Ti-10V-2Fe-3Al alloy with fine-grainedβphases was fabricated by friction stir processing with opti-mized processing parameters.The superplastic behavior of the specimens was investigated by tensile deformation at dif...Ti-10V-2Fe-3Al alloy with fine-grainedβphases was fabricated by friction stir processing with opti-mized processing parameters.The superplastic behavior of the specimens was investigated by tensile deformation at different strain rates and temperatures,and an optimal superplastic elongation of 634%was achieved at 700℃ and 3×10^(-4)/s.An annealing treatment at 650℃ for 60 min showed a mi-crostructure withαprecipitates distributed in theβmatrix in the friction stir specimen.Such pre-heat treatment improves the superplasticity of the specimen,achieving an elongation of up to 807%at 750℃ and 3×10^(-4)/s.The influences of tensile temperatures and strain rates on the microstructural evolution,such as grain size variation,grain morphology,and phase transformations,were discussed.The super-plastic deformation behavior of fine-grained Ti-10V-2Fe-3Al alloy is controlled by grain boundary sliding and accompanied by dynamic phase transformation and recrystallization.展开更多
In order to develop the liquid phase sintering process of WC-Ni3Al-B composites,the preparation process of WC＋Ni3Al prealloyed powder by reaction synthesis of carbonyl Ni,analytical purity Al and coarse WC powders wa...In order to develop the liquid phase sintering process of WC-Ni3Al-B composites,the preparation process of WC＋Ni3Al prealloyed powder by reaction synthesis of carbonyl Ni,analytical purity Al and coarse WC powders was investigated.DSC and XRD were adopted to study the procedure of phase transformation for the 3Ni＋Al and 70%WC＋（3Ni＋Al） mixed powders in temperature ranges of 550-1200 °C and 25-1400 °C,respectively.The results demonstrate that the formation mechanism of Ni3Al depends on the reaction temperature.Besides WC phase,there exist Ni2Al3,NiAl and Ni3Al intermetallics in the powder mixture after heat treatment at 200-660 °C,while only NiAl and Ni3Al exist at 660-1100 °C.Homogeneous WC＋Ni3Al powder mixture can be obtained in the temperature range of 1100-1200 °C.The WC-30%（Ni3Al-B） composites prepared from the mixed powders by conventional powder metallurgy technology show nearly full density and the shape of WC is round.WC-30%（Ni3Al-B） composites exhibit higher hardness of 9.7 GPa,inferior bending strength of 1800 MPa and similar fracture toughness of 18 MPa-m1/2 compared with commercial cemented carbides YGR45（WC-30%（Co-Ni-Cr））.展开更多
After the hot deformation sample of Ti-10V-2Fe-3Al alloy was treated by solid solution in theα+βtwo-phase region,the coarseβgrains that often appeared in theβsingle phase region were observed in the local region,i...After the hot deformation sample of Ti-10V-2Fe-3Al alloy was treated by solid solution in theα+βtwo-phase region,the coarseβgrains that often appeared in theβsingle phase region were observed in the local region,indicating that the abnormal grain growth occurred in the local microstructural region,and the macrostructure also showed abnormally coarse grains(ACGs).The dynamic recrystallization(DRX)behavior of Ti-10V-2Fe-3Al titanium alloy was systematically investigated through hot compression tests on the Gleeble-3800 system.The DRX model ofβgrains was established,and the quantitative correlation between DRX characteristics and the appearance of ACG was clarified.Based on these results,a numerical simulation platform was developed to realize the visual prediction of ACG distribution.The results show that the increase of deformation temperature and the decrease of strain rate both contribute to a significant increase in the grain size(d_(DRX)))and volume fraction(X_(DRX))of DRXed grains.However,the proper X_(DRX)and smaller d_(DRX))at low deformation temperature and high strain rate make the macro and microstructure show ACGs after solid solution.Interestingly,if the DRX degree is excessive or insufficient,ACGs cannot be produced,indicating that ACGs are solid solution products based on the appropriate DRX degree.According to the flow curves and statistical results of microstructure,the quantitative model of DRX kinetics and DRX grain size model were constructed,and the quantitative criterion model that is related to the formation of ACG with grain size(d_(DRX)))and volume fraction(X_(DRX))of DRXed grains as the key parameters was established,i.e.,d_(DRX)≤2.60µm,72.5%≤X_(DRX)≤87.9%.By integrating the subroutine of coarse grain criterion,the isothermal compression process of cylindrical samples and the actual die forging process of H-shaped parts were simulated by DEFORM-3D software of finite element(FE),respectively,and the visual prediction of the distribution of macroscopic ACGs was realized.There is a good consistency between the tested results and the simulated results,indicating a strong correlation between macroscopic ACGs and microscopic DRX.展开更多
基金financially supported by the National Natural Science Foundation of China(No.52105373)the China Scholarship Council(No.202106020094).
文摘Ti-10V-2Fe-3Al alloy with fine-grainedβphases was fabricated by friction stir processing with opti-mized processing parameters.The superplastic behavior of the specimens was investigated by tensile deformation at different strain rates and temperatures,and an optimal superplastic elongation of 634%was achieved at 700℃ and 3×10^(-4)/s.An annealing treatment at 650℃ for 60 min showed a mi-crostructure withαprecipitates distributed in theβmatrix in the friction stir specimen.Such pre-heat treatment improves the superplasticity of the specimen,achieving an elongation of up to 807%at 750℃ and 3×10^(-4)/s.The influences of tensile temperatures and strain rates on the microstructural evolution,such as grain size variation,grain morphology,and phase transformations,were discussed.The super-plastic deformation behavior of fine-grained Ti-10V-2Fe-3Al alloy is controlled by grain boundary sliding and accompanied by dynamic phase transformation and recrystallization.
基金Project (2012CB723906) supported by the National Basic Research Program of China
文摘In order to develop the liquid phase sintering process of WC-Ni3Al-B composites,the preparation process of WC＋Ni3Al prealloyed powder by reaction synthesis of carbonyl Ni,analytical purity Al and coarse WC powders was investigated.DSC and XRD were adopted to study the procedure of phase transformation for the 3Ni＋Al and 70%WC＋（3Ni＋Al） mixed powders in temperature ranges of 550-1200 °C and 25-1400 °C,respectively.The results demonstrate that the formation mechanism of Ni3Al depends on the reaction temperature.Besides WC phase,there exist Ni2Al3,NiAl and Ni3Al intermetallics in the powder mixture after heat treatment at 200-660 °C,while only NiAl and Ni3Al exist at 660-1100 °C.Homogeneous WC＋Ni3Al powder mixture can be obtained in the temperature range of 1100-1200 °C.The WC-30%（Ni3Al-B） composites prepared from the mixed powders by conventional powder metallurgy technology show nearly full density and the shape of WC is round.WC-30%（Ni3Al-B） composites exhibit higher hardness of 9.7 GPa,inferior bending strength of 1800 MPa and similar fracture toughness of 18 MPa-m1/2 compared with commercial cemented carbides YGR45（WC-30%（Co-Ni-Cr））.
基金Projects(52275388,52075474)supported by the National Natural Science Foundation of ChinaProject(236Z1008G)supported by the Special Project of Hebei Provincial Central Government Guiding Local Science and Technology Development,China+1 种基金Project(E2022203206)supported by the Natural Science Foundation of Hebei Province,ChinaProject(241080457A)supported by the Shijiazhuang's University-Industry-Academia Cooperation Project in Hebei Province-Major Science and Technology Special Project,China。
文摘After the hot deformation sample of Ti-10V-2Fe-3Al alloy was treated by solid solution in theα+βtwo-phase region,the coarseβgrains that often appeared in theβsingle phase region were observed in the local region,indicating that the abnormal grain growth occurred in the local microstructural region,and the macrostructure also showed abnormally coarse grains(ACGs).The dynamic recrystallization(DRX)behavior of Ti-10V-2Fe-3Al titanium alloy was systematically investigated through hot compression tests on the Gleeble-3800 system.The DRX model ofβgrains was established,and the quantitative correlation between DRX characteristics and the appearance of ACG was clarified.Based on these results,a numerical simulation platform was developed to realize the visual prediction of ACG distribution.The results show that the increase of deformation temperature and the decrease of strain rate both contribute to a significant increase in the grain size(d_(DRX)))and volume fraction(X_(DRX))of DRXed grains.However,the proper X_(DRX)and smaller d_(DRX))at low deformation temperature and high strain rate make the macro and microstructure show ACGs after solid solution.Interestingly,if the DRX degree is excessive or insufficient,ACGs cannot be produced,indicating that ACGs are solid solution products based on the appropriate DRX degree.According to the flow curves and statistical results of microstructure,the quantitative model of DRX kinetics and DRX grain size model were constructed,and the quantitative criterion model that is related to the formation of ACG with grain size(d_(DRX)))and volume fraction(X_(DRX))of DRXed grains as the key parameters was established,i.e.,d_(DRX)≤2.60µm,72.5%≤X_(DRX)≤87.9%.By integrating the subroutine of coarse grain criterion,the isothermal compression process of cylindrical samples and the actual die forging process of H-shaped parts were simulated by DEFORM-3D software of finite element(FE),respectively,and the visual prediction of the distribution of macroscopic ACGs was realized.There is a good consistency between the tested results and the simulated results,indicating a strong correlation between macroscopic ACGs and microscopic DRX.
