The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that...The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that discontinuous dynamic recrystallization（DDRX） is the predominant recrystallization mechanism at temperature higher than 1050 °C and strain rate lower than 0.01 s-1.Meanwhile,continuous dynamic recrystallization is the main mechanism observed at temperature below 1050 °C and strain rate above 0.01 s-1,mixed with a few DDRX grains.In addition,decreasing strain rate and increasing deformation temperature are found to facilitate the progress of DRX and refinement of grains in the Ti alloy in β forging process.展开更多
The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and el...The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.展开更多
By means of laser shock processing(LSP)treatment,a nanostructured surface layer was formed on 1Cr11Ni2W2MoV stainless steel.Group contrastive high cycle fatigue tests were carried out in 1Cr11Ni2W2MoV stainless steel ...By means of laser shock processing(LSP)treatment,a nanostructured surface layer was formed on 1Cr11Ni2W2MoV stainless steel.Group contrastive high cycle fatigue tests were carried out in 1Cr11Ni2W2MoV stainless steel before and after LSP treated.The experimental data was analyzed by mathematical statistics method and the influence mechanism of fatigue properties affected by LSP treatment was also researched.The results indicate that LSP treatment can improve the high cycle fatigue life of 1Cr11Ni2W2MoV stainless steel effectively.The ultra-fine grained surface layer with residual compressive stress and nanostructured surface layer make great contributions to the improvement in fatigue properties of 1Cr11Ni2W2MoV stainless steel.展开更多
In this study,uniaxial hot compression tests were carried out between 200 and 400℃ over strain rates of0.001-1 s-1 to investigate the hot deformation behavior of Mg-2 Zn-1 Al-0.2 RE alloy with coarse grains.The avera...In this study,uniaxial hot compression tests were carried out between 200 and 400℃ over strain rates of0.001-1 s-1 to investigate the hot deformation behavior of Mg-2 Zn-1 Al-0.2 RE alloy with coarse grains.The average activation energy was measured to be 174.51 kJ/mol.In addition,a constitutive relation based on the Arrhenius equation was established.Dynamic recrystallization(DRX) kinetics were studied by Avrami equation to characterize the evolution of DRX volume fraction.DRX was favored at high temperatures of 300-400℃ and low strain rates of 0.001-0.01 s-1.According to dynamic material model and Prasad’s instability criterion,a maximum power dissipation of 38% and 32% occurs at 400℃/0.001 s-1 and 400℃/0.01 s-1,respectively.According to the proce ssing map,330-400℃/0.001-0.01 s-1was determined as the optimum deformation parameter range.展开更多
Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN...Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN) nanopowders. At first, Nb2O5 reacted with melting sodium hydroxide and transformed into dispersible oxide. The resulting glassy substance after cooling was dispersed and washed several times in distilled water to remove the Na+ ions. The as-prepared colloidal Nb2O5-nH2O was subsequently mixed with acetic solution of barium acetate and magnesium acetate according to the required molar proportions and followed by gelation. The ultrafine BMN powders were finally obtained after heat-treating the gel at 820℃for 1 h, and the as-sintered nanoceramics revealed a high relative density of 98.2%, and a high microwave Q-factor, of 10397 at 1.45GHz.展开更多
基金Project (2007CB613803) supported by the National Basic Research Program of ChinaProject (2010GQC0170) supported by the Natural Science Foundation of Jiangxi Province,ChinaProject (GJJ11159) supported by the Educational Committee of Jiangxi Province,China
文摘The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that discontinuous dynamic recrystallization（DDRX） is the predominant recrystallization mechanism at temperature higher than 1050 °C and strain rate lower than 0.01 s-1.Meanwhile,continuous dynamic recrystallization is the main mechanism observed at temperature below 1050 °C and strain rate above 0.01 s-1,mixed with a few DDRX grains.In addition,decreasing strain rate and increasing deformation temperature are found to facilitate the progress of DRX and refinement of grains in the Ti alloy in β forging process.
基金Project(20871101)supported by the National Natural Science Foundation of ChinaProject(2009WK2007)supported by Key Project of Science and Technology Department of Hunan Province,ChinaProject(CX2009B133)supported by Colleges and Universities in Hunan Province Plans to Graduate Research and Innovation,China
文摘The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.
文摘By means of laser shock processing(LSP)treatment,a nanostructured surface layer was formed on 1Cr11Ni2W2MoV stainless steel.Group contrastive high cycle fatigue tests were carried out in 1Cr11Ni2W2MoV stainless steel before and after LSP treated.The experimental data was analyzed by mathematical statistics method and the influence mechanism of fatigue properties affected by LSP treatment was also researched.The results indicate that LSP treatment can improve the high cycle fatigue life of 1Cr11Ni2W2MoV stainless steel effectively.The ultra-fine grained surface layer with residual compressive stress and nanostructured surface layer make great contributions to the improvement in fatigue properties of 1Cr11Ni2W2MoV stainless steel.
基金the National Key Research and Development Program of China(2016YFB0301104)National Natural Science Foundation of China(51771043)。
文摘In this study,uniaxial hot compression tests were carried out between 200 and 400℃ over strain rates of0.001-1 s-1 to investigate the hot deformation behavior of Mg-2 Zn-1 Al-0.2 RE alloy with coarse grains.The average activation energy was measured to be 174.51 kJ/mol.In addition,a constitutive relation based on the Arrhenius equation was established.Dynamic recrystallization(DRX) kinetics were studied by Avrami equation to characterize the evolution of DRX volume fraction.DRX was favored at high temperatures of 300-400℃ and low strain rates of 0.001-0.01 s-1.According to dynamic material model and Prasad’s instability criterion,a maximum power dissipation of 38% and 32% occurs at 400℃/0.001 s-1 and 400℃/0.01 s-1,respectively.According to the proce ssing map,330-400℃/0.001-0.01 s-1was determined as the optimum deformation parameter range.
文摘Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN) nanopowders. At first, Nb2O5 reacted with melting sodium hydroxide and transformed into dispersible oxide. The resulting glassy substance after cooling was dispersed and washed several times in distilled water to remove the Na+ ions. The as-prepared colloidal Nb2O5-nH2O was subsequently mixed with acetic solution of barium acetate and magnesium acetate according to the required molar proportions and followed by gelation. The ultrafine BMN powders were finally obtained after heat-treating the gel at 820℃for 1 h, and the as-sintered nanoceramics revealed a high relative density of 98.2%, and a high microwave Q-factor, of 10397 at 1.45GHz.
基金Planned Scientific Research Project of Education Department of Shaanxi Provincial Government(15JS056)Pre-research Foundation of Jinchuan Company-Xi'an University of Architecture and Technology(YY1501)
