This paper describes the effect of the composition of the oxide films on the properties of electrodes Ti/M<sub>x</sub>Ti<sub>y</sub>Sn<sub>z</sub>O<sub>2</sub> (M = Ir o...This paper describes the effect of the composition of the oxide films on the properties of electrodes Ti/M<sub>x</sub>Ti<sub>y</sub>Sn<sub>z</sub>O<sub>2</sub> (M = Ir or Ru) prepared by the polymeric precursor method. XRD studies showed that the anodes are formed by solid solutions. The electrodes containing IrO<sub>2</sub> exhibit lower activity for the oxygen evolution reaction. The doping of the electrode surface with SnO<sub>2</sub> improves the catalytic properties of the anodes. However, it should be held in appropriate compositions, because the change in the atomic ratio of this element shows a marked effect on the stability of the oxides. Electrode Ti/Ir<sub>0.2</sub>Ti<sub>0.3</sub>Sn<sub>0.5</sub>O<sub>2</sub> has lower lifetime, i.e. 6 hours. The 20% decrease in the stoichiometric amount of SnO<sub>2</sub> increases the time to a value above 70 hours, as observed for Ti/Ir<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub>. Electrode Ti/Ru<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub> shows lifetime of 11 hours;therefore IrO<sub>2</sub> is more stable than RuO<sub>2</sub> under the conditions investigated. These results suggest that electrode Ti/Ir<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub> is promising for different applications, such as water electrolysis, capacitors and organic electrosynthesis.展开更多
In the current work, LaNiO3 perovskite was synthesized using the polymeric precursor method. The materials were thermally treated at 300°C for 2 hours, subsequently supported on alumina or zirconia and finally ca...In the current work, LaNiO3 perovskite was synthesized using the polymeric precursor method. The materials were thermally treated at 300°C for 2 hours, subsequently supported on alumina or zirconia and finally calcined at 800°C for 4 hours. The resulting samples were characterized by X-ray diffraction, thermogravimetry, BET surface area and thermo-programmed reduction. Steam reforming reactions were carried out at 750°C and 6 bar during 4 hours using a pilot reactor under a H2O:CH4 ratio of 2.5. The mass of catalysts was about 5.7 g. X-ray diffraction patterns confirmed the formation of the perovskite structure in all samples prepared. The results also showed that lanthanum nickelate was more efficient when supported on alumina than zirconia. Finally, it was observed that the methane conversion was approximately 94% and the selectivity to hydrogen was about 70%. In all cases low selectivity to CO and CO2 was verified.展开更多
In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and ...In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and the average particle size was 20 nm determined by FEG-SEM analysis. The photocatalytic activities of these films were studied using Rhodamine B as a target compound in a fixed bed reactor developed in our laboratory and UV lamp. It was observed that the addition of copper to TiO2 increased significantly its photocatalytic activity during the oxidation of Rhodamine B. The degradation exceeded 90% within 48 hours of irradiation compared to 38% when pure TiO2 was used. Moreover, there was a reduction in the particles band gap energy when compared to that of pure TiO2. These results indicate that the TiO2/CuO films are promising catalysts for the development of fixed bed reactors to be used to treat effluents containing azo dyes.展开更多
This work presents a study on the synthesis of LaNixCo1-xO3 perovskites via complex precursor methods. Perovskite oxides with the composition LaNixCo1-xO3 were synthesized by chelating precursor and polymeric precurso...This work presents a study on the synthesis of LaNixCo1-xO3 perovskites via complex precursor methods. Perovskite oxides with the composition LaNixCo1-xO3 were synthesized by chelating precursor and polymeric precursor methods using nickel and/or cobalt nitrates, lanthanum nitrate, ethylene glycol, citric acid, and EDTA as starting source. The obtained perovskite were characterized by thermogravimetric analysis, infrared spectroscopy, X-ray diffraction and the morphology of the samples were investigated by N2 adsorption experiments and average medium particle size. TG curves and FTIR spectra were particularly useful in establishing of the optimal calcination temperature of the precursor powders. X-ray diffraction patterns revealed the formation of the perovskite structure in all samples prepared by both synthesis method and after calcinations at 700℃. The results showed that the preparation method resulted in oxides with the intended structure. The specific surface area values were influenced by preparation method.展开更多
Layered double hydroxides(LDHs)are widely used owing to their unique alternating anionic and cationic layered twodimensional(2D)structures.However,studies on the preparation of 2D LDH nanosheets with uniform thickness...Layered double hydroxides(LDHs)are widely used owing to their unique alternating anionic and cationic layered twodimensional(2D)structures.However,studies on the preparation of 2D LDH nanosheets with uniform thickness and their photodetectors are limited.In this study,two novel ultrathin LDH(Ca-In and Ca-Al LDH)nanosheets are peeled off from precursor bimetallic phosphides through the original precursor method.Both Ca-In and Ca-Al LDH nanosheets demonstrate a uniform thickness distribution with an average thickness of 3–4 nm,micron-level lateral sizes,and moderate bandgap.Owing to its broad light absorption range,hydrophilicity,and stability,Ca-In and Ca-Al LDH nanosheets are applied for the first time in photoelectrochemical photodetectors,realizing a wide range of light detection from ultraviolet(365 nm)to visible light(635 nm).Moreover,the fabricated photodetectors exhibit excellent cycle stability,and the average photocurrent density shows no reduction after 70 days.Therefore,this study provides an effective method to prepare 2D Ca-In and Ca-Al LDH nanosheets with uniform thickness and photoelectric application prospects.展开更多
SnO2 and Sb-doped SnO2 particles were synthesized using the polymeric precursor method with different Sn salt precursors： SnCl2.2H2O, SnCl4.5H20, or Sn citrate. Sb2O3 was used as the precursor of Sb, and the molar ra...SnO2 and Sb-doped SnO2 particles were synthesized using the polymeric precursor method with different Sn salt precursors： SnCl2.2H2O, SnCl4.5H20, or Sn citrate. Sb2O3 was used as the precursor of Sb, and the molar ratio of nsn：nsb was held constant. FTIR and TGA/DTA were used to examine the influence of the Sn precursor on the formation and thermal decomposition of the Sn and Sn-Sb complexes. The calcination products obtained from heating the Sn and Sn-Sb complexes at 500℃ in air were analyzed using XRD and TEM analysis. The results revealed that the SnO2 and Sb-doped SnO2 formation temperatures depended on the nature of the Sn precursor. The calcination products were found to be SnO2 and Sb-doped SnO2 particles, which crystallized in a tetragonal cassiterite structure with a highly preferred （110） planar orientation. The Sn precursor and the presence of Sb in the SnO2 matrix strongly influenced the crystallinity and lattice parameters.展开更多
Based on the borehole strainmeter recordings immediately before the strong earthquakes （Ms〉7.5） during the period from 2001 to 2005 observed at the Taian observation station, Shandong Province, the authors make a s...Based on the borehole strainmeter recordings immediately before the strong earthquakes （Ms〉7.5） during the period from 2001 to 2005 observed at the Taian observation station, Shandong Province, the authors make a systematic and objective examination of the precursor waves of the quakes. The effects of Earth tides with periods larger than 128 min are eliminated through high-pass filtering; and atmospheric-pressure inferences are removed by linear regression. The 2-128 min signals are then separated into six frequency bands by employing the wavelet method. Results indicate that the wavelet method is capable of picking out information of weak variations in the signals. According to the characteristics of the ＇precursor waves＇ obtained from wavelet transformation, the method of overrun ratio analysis is put forward for examination. All the detailed components of the wavelets have been analyzed. For the time series of the overrun rate in all these components, statisitical calculation has been made for the slopes of fit curves, and mean values and standard deviations were obtained and positive-negative slope ratios were analyzed. The three statistical data show that ＇precursor waves＇ are not widely recorded by borehole strainmeter within 15 days before remote strong earthquakes.展开更多
The predictability of El Ni-o-Southern Oscillation (ENSO) has been an important area of study for years. Searching for the optimal precursor (OPR) of ENSO occurrence is an effective way to understand its predictabilit...The predictability of El Ni-o-Southern Oscillation (ENSO) has been an important area of study for years. Searching for the optimal precursor (OPR) of ENSO occurrence is an effective way to understand its predictability. The CNOP (conditional nonlinear optimal perturbation), one of the most effective ways to depict the predictability of ENSO, is adopted to study the optimal sea surface temperature (SST) precursors (SST-OPRs) of ENSO in the IOCAS ICM (intermediate coupled model developed at the Institute of Oceanology, Chinese Academy of Sciences). To seek the SST-OPRs of ENSO in the ICM, non-ENSO events simulated by the ICM are chosen as the basic state. Then, the gradient-definition-based method (GD method) is employed to solve the CNOP for different initial months of the basic years to obtain the SSTOPRs. The experimental results show that the obtained SST-OPRs present a positive anomaly signal in the western-central equatorial Pacific, and obvious differences exist in the patterns between the different seasonal SST-OPRs along the equatorial western-central Pacific, showing seasonal dependence to some extent. Furthermore, the non-El Ni-o events can eventually evolve into El Ni-o events when the SST-OPRs are superimposed on the corresponding seasons;the peaks of the Ni-o3.4 index occur at the ends of the years, which is consistent with the evolution of the real El Ni-o. These results show that the GD method is an effective way to obtain SST-OPRs for ENSO events in the ICM. Moreover, the OPRs for ENSO depicted using the GD method provide useful information for finding the early signal of ENSO in the ICM.展开更多
Selective-controlled structure and shape of CeVO4 nanocrystals were successfully synthesized via a hydrothermal method from Na3VO4·12H2O and Ce（NO3）3·6H2O.The resulting products were characterized by X-ray...Selective-controlled structure and shape of CeVO4 nanocrystals were successfully synthesized via a hydrothermal method from Na3VO4·12H2O and Ce（NO3）3·6H2O.The resulting products were characterized by X-ray powder diffraction （XRD）,field emission scanning electron microscopy （FESEM） and energy dispersive spectroscopy （EDS）.The influence of hydrothermal temperature,precursor solution concentration on the crystal and morphology of products were further studied.The results showed that the as-synthesized products exhibited pure single-crystal CeVO4 nanoparticles with tetragonal structure.The hydrothermal temperature and precursor solution concentration had important effects on the formation of CeVO4 nanoparticles.Furthermore,the growth mechanism of CeVO4 nanoparticles was explained with Ostwald ripening mechanism.展开更多
The synthesis of precursor of green phosphors, LaPO4: Ce, Tb, by means of co-precipitation with cocurrent flow feed was studied. The effects of the reaction temperature, the kind and concentration of the acid in the b...The synthesis of precursor of green phosphors, LaPO4: Ce, Tb, by means of co-precipitation with cocurrent flow feed was studied. The effects of the reaction temperature, the kind and concentration of the acid in the bottom water, and the charging rate on the physical properties, such as particle size, were investigated. It is found that the particle size of the powder is controllable by adjusting acidity in bottom water and charging rate. The powder with diameter size of 3 to 5μm was obtained. Its XRD and SEM were analyzed. XRD patterns of the as-prepared green phosphor powders display the typical peaks of CePO4. SEM shows that the morphology of powders is ball-shaped.展开更多
In the process of synthesis of nanometer SiC precursors with sol-gel of SiO2 and lignin , the products of all sizes required can be controlled by the concentration of reac-t ants , pH, temperature, reaction and ageing...In the process of synthesis of nanometer SiC precursors with sol-gel of SiO2 and lignin , the products of all sizes required can be controlled by the concentration of reac-t ants , pH, temperature, reaction and ageing time , and so on . The best conditions in this research are : the concentration of Na2SiO3 and organic matters are 4. 50% and 26.4% respectively, pH = 3.3 , T = 65℃ , ageing time is 30min , dried at 150 ℃ , the size of SiC precursors is about 2.0μm .展开更多
A series of Ni/ZrO_2 catalysts were synthesized by urea combustion method for CO_2 methanation.The effects of zirconium precursors and urea dosage on the structure and catalytic performance of the catalysts were teste...A series of Ni/ZrO_2 catalysts were synthesized by urea combustion method for CO_2 methanation.The effects of zirconium precursors and urea dosage on the structure and catalytic performance of the catalysts were tested.Results showed that the Ni/ZrO_2–O catalyst derived from zirconium oxynitrate hydrate exhibited better catalytic activity than the Ni/ZrO_2 catalyst because of its higher Ni dispersion and smaller Ni particle size.In addition,the urea dosage significantly influenced the low-temperature activity of the catalysts by affecting the metal–support interaction,Ni dispersion,and Ni particle size.The Ni/ZrO_2–O-0.4 catalyst with a urea-to-nitrate molar ratio of 0.4 exhibited the best catalytic activity owing to its moderate metal–support interaction,highest Ni dispersion,and smallest Ni particle size,achieving 69.2% CO_2 conversion and 100% CH_4 selectivity at 300℃,0.1 MPa,and a weight hour space velocity(WHSV)of 50,000 mL/(g·h).Moreover,the urea combustion method can lead to the entire phase transformation from monoclinic ZrO_2 to tetragonal ZrO_2 accompanied by the incorporation of oxygen vacancies in the ZrO_2 lattice.This phenomenon can also be related to the high catalytic activity of the as-prepared catalysts.展开更多
LiNi0.5Mn1.5O4 was synthesized by two different coprecipitation methods:composite carbonate process and composite hydroxide method. The effects of calcination temperature of precursors on the physical properties and e...LiNi0.5Mn1.5O4 was synthesized by two different coprecipitation methods:composite carbonate process and composite hydroxide method. The effects of calcination temperature of precursors on the physical properties and electrochemical performance of the samples were investigated. The results of scanning electron microscopy(SEM) show that as calcination temperature increases,the crystallinity of the samples is improved,and their grain sizes are obviously increased. X-Ray diffraction(XRD) data show that the LiNi0.5Mn1.5O4 compounds obtained by two coprecipitation methods both exhibit a pure cubic spinel structure without any impurities. Furthermore,it is found that the samples prepared with relatively high temperature precursors present large initial discharge capacity(>125 mA·h/g) and excellent cycling stability with a capacity retention rate larger than 91% after 30 cycles at current density of 1 C. This probably derives from their higher crystallinity and larger grain sizes. However,the initial discharge capacity of LiNi0.5Mn1.5O4 synthesized by composite carbonate process is smaller than that prepared by composite carbonate process,but it shows better capacity retention ability.展开更多
Using rare earth and zinc coordination polymers with aromatic carboxylic acids as the precursors, composing with the polyethylene glycol (PEG) as the dispersing media, micro crystalline phosphors Zn_3(PO_4)_2∶Eu 3+ a...Using rare earth and zinc coordination polymers with aromatic carboxylic acids as the precursors, composing with the polyethylene glycol (PEG) as the dispersing media, micro crystalline phosphors Zn_3(PO_4)_2∶Eu 3+ and LaPO_4∶Eu 3+ were synthesized by in-situ co-precipitation method. X-ray diffraction and scanning electronic micrograph were used to characterize the resultant samples, whose particle size are in the range of micrometer. The emission spectra of Zn_3(PO_4)_2∶Eu 3+ (λ_ ex=245 nm) and LaPO_4∶Eu 3+ (λ_ ex=390 nm) shows that the emission for Eu 3+ in Zn_3(PO_4)_2 is dominated by the 5D_0→7F_1 (592 nm) magnetic-dipole transition,While the dominant emission for Eu 3+ in LaPO_4 is the typical hypersensitive transition 5D_0→7F_2 (618 nm).展开更多
Most earthquakes on the Chinese mainland have occurred within the depth range of 10-25 km,which is usually called the seismogenic layer.According to the rule of penetration depth,the precursor of the electric anomaly,...Most earthquakes on the Chinese mainland have occurred within the depth range of 10-25 km,which is usually called the seismogenic layer.According to the rule of penetration depth,the precursor of the electric anomaly,which is transferred from the seismogenic layer to the Earth’s surface,should be very weak,but the ability to monitor earthquakes can be greatly improved if the field precursor effect is taken into consideration because of expansion of the electric anomaly area.The results of one-and two-dimensional modeling computations are consistent with the observed fact that the apparent resistivity decreases before earthquakes.This provides good evidence for our inference.The corresponding physical mechanism is that the conductivity of the anomaly area may be increased by the rock dilatation and fluid permeation due to the stress effect during the developing process of earthquakes.展开更多
Seismic hazard analysis is gaining increased attention in the present era because of the catastrophic effects of earthquakes.Scientists always have as a goal to develop new techniques that will help forecast earthquak...Seismic hazard analysis is gaining increased attention in the present era because of the catastrophic effects of earthquakes.Scientists always have as a goal to develop new techniques that will help forecast earthquakes before their reoccurrence. In this research,we have performed a shear failure experiment on rock samples with prefabricated cracks to simulate the process of plate movement that forms strike-slip faults. We studied the evolution law of the deformation field to simulate the shear failure experiment, and these results gave us a comprehensive understanding of the elaborate strain distribution law and its formation process with which to identify actual fault zones. We performed uniaxial compression tests on marble slabs with prefabricated double shear cracks to study the distribution and evolution of the deformation field during shear failure. Analysis of the strain field at different loading stages showed that with an increase in the load, the shear strain field initially changed to a disordered-style distribution. Further, the strain field was partially concentrated and finally completely concentrated near the crack and then distributed in the shape of a strip along the crack. We also computed coefficients of variation(CVs) for the physical quantities u, v, and exy, which varied with the load. The CV curves were found to correspond to the different loading stages. We found that at the uniform deformation stage, the CV value was small and changed slowly,whereas at the later nonuniform deformation stage, the CV value increased sharply and changed abruptly. Therefore, the precursor to a rock sample breakdown can be predicted by observing the variation characteristics of CV statistics. The correlation we found between our experimental and theoretical results revealed that our crack evolution and sample deformation results showed good coupling with seismic distribution characteristics near the San Andreas Fault.展开更多
文摘This paper describes the effect of the composition of the oxide films on the properties of electrodes Ti/M<sub>x</sub>Ti<sub>y</sub>Sn<sub>z</sub>O<sub>2</sub> (M = Ir or Ru) prepared by the polymeric precursor method. XRD studies showed that the anodes are formed by solid solutions. The electrodes containing IrO<sub>2</sub> exhibit lower activity for the oxygen evolution reaction. The doping of the electrode surface with SnO<sub>2</sub> improves the catalytic properties of the anodes. However, it should be held in appropriate compositions, because the change in the atomic ratio of this element shows a marked effect on the stability of the oxides. Electrode Ti/Ir<sub>0.2</sub>Ti<sub>0.3</sub>Sn<sub>0.5</sub>O<sub>2</sub> has lower lifetime, i.e. 6 hours. The 20% decrease in the stoichiometric amount of SnO<sub>2</sub> increases the time to a value above 70 hours, as observed for Ti/Ir<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub>. Electrode Ti/Ru<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub> shows lifetime of 11 hours;therefore IrO<sub>2</sub> is more stable than RuO<sub>2</sub> under the conditions investigated. These results suggest that electrode Ti/Ir<sub>0.3</sub>Ti<sub>0.4</sub>Sn<sub>0.3</sub>O<sub>2</sub> is promising for different applications, such as water electrolysis, capacitors and organic electrosynthesis.
基金The authors wish to acknowledge RECAT-Petrobras,Rede de Hidrogenio-MCTANP for their financial support and scholarship grants.
文摘In the current work, LaNiO3 perovskite was synthesized using the polymeric precursor method. The materials were thermally treated at 300°C for 2 hours, subsequently supported on alumina or zirconia and finally calcined at 800°C for 4 hours. The resulting samples were characterized by X-ray diffraction, thermogravimetry, BET surface area and thermo-programmed reduction. Steam reforming reactions were carried out at 750°C and 6 bar during 4 hours using a pilot reactor under a H2O:CH4 ratio of 2.5. The mass of catalysts was about 5.7 g. X-ray diffraction patterns confirmed the formation of the perovskite structure in all samples prepared. The results also showed that lanthanum nickelate was more efficient when supported on alumina than zirconia. Finally, it was observed that the methane conversion was approximately 94% and the selectivity to hydrogen was about 70%. In all cases low selectivity to CO and CO2 was verified.
基金FAPESP,FAPEMIG,CAPES and CNPq for the financial support.
文摘In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and the average particle size was 20 nm determined by FEG-SEM analysis. The photocatalytic activities of these films were studied using Rhodamine B as a target compound in a fixed bed reactor developed in our laboratory and UV lamp. It was observed that the addition of copper to TiO2 increased significantly its photocatalytic activity during the oxidation of Rhodamine B. The degradation exceeded 90% within 48 hours of irradiation compared to 38% when pure TiO2 was used. Moreover, there was a reduction in the particles band gap energy when compared to that of pure TiO2. These results indicate that the TiO2/CuO films are promising catalysts for the development of fixed bed reactors to be used to treat effluents containing azo dyes.
文摘This work presents a study on the synthesis of LaNixCo1-xO3 perovskites via complex precursor methods. Perovskite oxides with the composition LaNixCo1-xO3 were synthesized by chelating precursor and polymeric precursor methods using nickel and/or cobalt nitrates, lanthanum nitrate, ethylene glycol, citric acid, and EDTA as starting source. The obtained perovskite were characterized by thermogravimetric analysis, infrared spectroscopy, X-ray diffraction and the morphology of the samples were investigated by N2 adsorption experiments and average medium particle size. TG curves and FTIR spectra were particularly useful in establishing of the optimal calcination temperature of the precursor powders. X-ray diffraction patterns revealed the formation of the perovskite structure in all samples prepared by both synthesis method and after calcinations at 700℃. The results showed that the preparation method resulted in oxides with the intended structure. The specific surface area values were influenced by preparation method.
基金supported by the State Key Program of the National Natural Science Foundation of China(No.52130303)the National Key R&D Program of China(No.2016YFA0202302)+1 种基金the National Natural Science Foundation of China(Nos.52103093 and 52173078)the China Postdoctoral Science Foundation(No.2021M702424).
文摘Layered double hydroxides(LDHs)are widely used owing to their unique alternating anionic and cationic layered twodimensional(2D)structures.However,studies on the preparation of 2D LDH nanosheets with uniform thickness and their photodetectors are limited.In this study,two novel ultrathin LDH(Ca-In and Ca-Al LDH)nanosheets are peeled off from precursor bimetallic phosphides through the original precursor method.Both Ca-In and Ca-Al LDH nanosheets demonstrate a uniform thickness distribution with an average thickness of 3–4 nm,micron-level lateral sizes,and moderate bandgap.Owing to its broad light absorption range,hydrophilicity,and stability,Ca-In and Ca-Al LDH nanosheets are applied for the first time in photoelectrochemical photodetectors,realizing a wide range of light detection from ultraviolet(365 nm)to visible light(635 nm).Moreover,the fabricated photodetectors exhibit excellent cycle stability,and the average photocurrent density shows no reduction after 70 days.Therefore,this study provides an effective method to prepare 2D Ca-In and Ca-Al LDH nanosheets with uniform thickness and photoelectric application prospects.
文摘SnO2 and Sb-doped SnO2 particles were synthesized using the polymeric precursor method with different Sn salt precursors： SnCl2.2H2O, SnCl4.5H20, or Sn citrate. Sb2O3 was used as the precursor of Sb, and the molar ratio of nsn：nsb was held constant. FTIR and TGA/DTA were used to examine the influence of the Sn precursor on the formation and thermal decomposition of the Sn and Sn-Sb complexes. The calcination products obtained from heating the Sn and Sn-Sb complexes at 500℃ in air were analyzed using XRD and TEM analysis. The results revealed that the SnO2 and Sb-doped SnO2 formation temperatures depended on the nature of the Sn precursor. The calcination products were found to be SnO2 and Sb-doped SnO2 particles, which crystallized in a tetragonal cassiterite structure with a highly preferred （110） planar orientation. The Sn precursor and the presence of Sb in the SnO2 matrix strongly influenced the crystallinity and lattice parameters.
基金supported by National Natural Science Foundation of China (40374011)Joint Seismological Science Foundation of China (1040037)
文摘Based on the borehole strainmeter recordings immediately before the strong earthquakes （Ms〉7.5） during the period from 2001 to 2005 observed at the Taian observation station, Shandong Province, the authors make a systematic and objective examination of the precursor waves of the quakes. The effects of Earth tides with periods larger than 128 min are eliminated through high-pass filtering; and atmospheric-pressure inferences are removed by linear regression. The 2-128 min signals are then separated into six frequency bands by employing the wavelet method. Results indicate that the wavelet method is capable of picking out information of weak variations in the signals. According to the characteristics of the ＇precursor waves＇ obtained from wavelet transformation, the method of overrun ratio analysis is put forward for examination. All the detailed components of the wavelets have been analyzed. For the time series of the overrun rate in all these components, statisitical calculation has been made for the slopes of fit curves, and mean values and standard deviations were obtained and positive-negative slope ratios were analyzed. The three statistical data show that ＇precursor waves＇ are not widely recorded by borehole strainmeter within 15 days before remote strong earthquakes.
基金supported by the Fundamental Research Funds for the Central Universities (Grant No. 22120190 207)the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant No. XDA19060102)+4 种基金the National Key Research and Development Program of China (Grant No. 2017YFC1404102(2017YFC1404100))the National Programme on Global Change and Air-Sea Interaction (Grant No. GASIIPOVAI-06)National Natural Science Foundation of China (Grant Nos. 41690122(41690120), 41490644(41490640), 414210 05)the Taishan Scholarshipthe Institute of Oceanology, Chinese Academy of Sciences, for providing technical support for IOCAS ICM
文摘The predictability of El Ni-o-Southern Oscillation (ENSO) has been an important area of study for years. Searching for the optimal precursor (OPR) of ENSO occurrence is an effective way to understand its predictability. The CNOP (conditional nonlinear optimal perturbation), one of the most effective ways to depict the predictability of ENSO, is adopted to study the optimal sea surface temperature (SST) precursors (SST-OPRs) of ENSO in the IOCAS ICM (intermediate coupled model developed at the Institute of Oceanology, Chinese Academy of Sciences). To seek the SST-OPRs of ENSO in the ICM, non-ENSO events simulated by the ICM are chosen as the basic state. Then, the gradient-definition-based method (GD method) is employed to solve the CNOP for different initial months of the basic years to obtain the SSTOPRs. The experimental results show that the obtained SST-OPRs present a positive anomaly signal in the western-central equatorial Pacific, and obvious differences exist in the patterns between the different seasonal SST-OPRs along the equatorial western-central Pacific, showing seasonal dependence to some extent. Furthermore, the non-El Ni-o events can eventually evolve into El Ni-o events when the SST-OPRs are superimposed on the corresponding seasons;the peaks of the Ni-o3.4 index occur at the ends of the years, which is consistent with the evolution of the real El Ni-o. These results show that the GD method is an effective way to obtain SST-OPRs for ENSO events in the ICM. Moreover, the OPRs for ENSO depicted using the GD method provide useful information for finding the early signal of ENSO in the ICM.
基金financial support by the Open Project Program of the State Key Laboratory of Solid Lu-brication, Lanzhou Institute of Chemical Physics,Chinese Academy of Sciences (0804)
文摘Selective-controlled structure and shape of CeVO4 nanocrystals were successfully synthesized via a hydrothermal method from Na3VO4·12H2O and Ce（NO3）3·6H2O.The resulting products were characterized by X-ray powder diffraction （XRD）,field emission scanning electron microscopy （FESEM） and energy dispersive spectroscopy （EDS）.The influence of hydrothermal temperature,precursor solution concentration on the crystal and morphology of products were further studied.The results showed that the as-synthesized products exhibited pure single-crystal CeVO4 nanoparticles with tetragonal structure.The hydrothermal temperature and precursor solution concentration had important effects on the formation of CeVO4 nanoparticles.Furthermore,the growth mechanism of CeVO4 nanoparticles was explained with Ostwald ripening mechanism.
基金Rare Earth Special Project supported by National Development and Reform Commission
文摘The synthesis of precursor of green phosphors, LaPO4: Ce, Tb, by means of co-precipitation with cocurrent flow feed was studied. The effects of the reaction temperature, the kind and concentration of the acid in the bottom water, and the charging rate on the physical properties, such as particle size, were investigated. It is found that the particle size of the powder is controllable by adjusting acidity in bottom water and charging rate. The powder with diameter size of 3 to 5μm was obtained. Its XRD and SEM were analyzed. XRD patterns of the as-prepared green phosphor powders display the typical peaks of CePO4. SEM shows that the morphology of powders is ball-shaped.
文摘In the process of synthesis of nanometer SiC precursors with sol-gel of SiO2 and lignin , the products of all sizes required can be controlled by the concentration of reac-t ants , pH, temperature, reaction and ageing time , and so on . The best conditions in this research are : the concentration of Na2SiO3 and organic matters are 4. 50% and 26.4% respectively, pH = 3.3 , T = 65℃ , ageing time is 30min , dried at 150 ℃ , the size of SiC precursors is about 2.0μm .
文摘A series of Ni/ZrO_2 catalysts were synthesized by urea combustion method for CO_2 methanation.The effects of zirconium precursors and urea dosage on the structure and catalytic performance of the catalysts were tested.Results showed that the Ni/ZrO_2–O catalyst derived from zirconium oxynitrate hydrate exhibited better catalytic activity than the Ni/ZrO_2 catalyst because of its higher Ni dispersion and smaller Ni particle size.In addition,the urea dosage significantly influenced the low-temperature activity of the catalysts by affecting the metal–support interaction,Ni dispersion,and Ni particle size.The Ni/ZrO_2–O-0.4 catalyst with a urea-to-nitrate molar ratio of 0.4 exhibited the best catalytic activity owing to its moderate metal–support interaction,highest Ni dispersion,and smallest Ni particle size,achieving 69.2% CO_2 conversion and 100% CH_4 selectivity at 300℃,0.1 MPa,and a weight hour space velocity(WHSV)of 50,000 mL/(g·h).Moreover,the urea combustion method can lead to the entire phase transformation from monoclinic ZrO_2 to tetragonal ZrO_2 accompanied by the incorporation of oxygen vacancies in the ZrO_2 lattice.This phenomenon can also be related to the high catalytic activity of the as-prepared catalysts.
基金Project(2007CB613607) supported by the National Basic Research Program of China
文摘LiNi0.5Mn1.5O4 was synthesized by two different coprecipitation methods:composite carbonate process and composite hydroxide method. The effects of calcination temperature of precursors on the physical properties and electrochemical performance of the samples were investigated. The results of scanning electron microscopy(SEM) show that as calcination temperature increases,the crystallinity of the samples is improved,and their grain sizes are obviously increased. X-Ray diffraction(XRD) data show that the LiNi0.5Mn1.5O4 compounds obtained by two coprecipitation methods both exhibit a pure cubic spinel structure without any impurities. Furthermore,it is found that the samples prepared with relatively high temperature precursors present large initial discharge capacity(>125 mA·h/g) and excellent cycling stability with a capacity retention rate larger than 91% after 30 cycles at current density of 1 C. This probably derives from their higher crystallinity and larger grain sizes. However,the initial discharge capacity of LiNi0.5Mn1.5O4 synthesized by composite carbonate process is smaller than that prepared by composite carbonate process,but it shows better capacity retention ability.
文摘Using rare earth and zinc coordination polymers with aromatic carboxylic acids as the precursors, composing with the polyethylene glycol (PEG) as the dispersing media, micro crystalline phosphors Zn_3(PO_4)_2∶Eu 3+ and LaPO_4∶Eu 3+ were synthesized by in-situ co-precipitation method. X-ray diffraction and scanning electronic micrograph were used to characterize the resultant samples, whose particle size are in the range of micrometer. The emission spectra of Zn_3(PO_4)_2∶Eu 3+ (λ_ ex=245 nm) and LaPO_4∶Eu 3+ (λ_ ex=390 nm) shows that the emission for Eu 3+ in Zn_3(PO_4)_2 is dominated by the 5D_0→7F_1 (592 nm) magnetic-dipole transition,While the dominant emission for Eu 3+ in LaPO_4 is the typical hypersensitive transition 5D_0→7F_2 (618 nm).
文摘Most earthquakes on the Chinese mainland have occurred within the depth range of 10-25 km,which is usually called the seismogenic layer.According to the rule of penetration depth,the precursor of the electric anomaly,which is transferred from the seismogenic layer to the Earth’s surface,should be very weak,but the ability to monitor earthquakes can be greatly improved if the field precursor effect is taken into consideration because of expansion of the electric anomaly area.The results of one-and two-dimensional modeling computations are consistent with the observed fact that the apparent resistivity decreases before earthquakes.This provides good evidence for our inference.The corresponding physical mechanism is that the conductivity of the anomaly area may be increased by the rock dilatation and fluid permeation due to the stress effect during the developing process of earthquakes.
基金Support for this research was provided by the National Key R&D Program of China(grant numbers 2018YFC1504203 and SQ2017YFSF040025)
文摘Seismic hazard analysis is gaining increased attention in the present era because of the catastrophic effects of earthquakes.Scientists always have as a goal to develop new techniques that will help forecast earthquakes before their reoccurrence. In this research,we have performed a shear failure experiment on rock samples with prefabricated cracks to simulate the process of plate movement that forms strike-slip faults. We studied the evolution law of the deformation field to simulate the shear failure experiment, and these results gave us a comprehensive understanding of the elaborate strain distribution law and its formation process with which to identify actual fault zones. We performed uniaxial compression tests on marble slabs with prefabricated double shear cracks to study the distribution and evolution of the deformation field during shear failure. Analysis of the strain field at different loading stages showed that with an increase in the load, the shear strain field initially changed to a disordered-style distribution. Further, the strain field was partially concentrated and finally completely concentrated near the crack and then distributed in the shape of a strip along the crack. We also computed coefficients of variation(CVs) for the physical quantities u, v, and exy, which varied with the load. The CV curves were found to correspond to the different loading stages. We found that at the uniform deformation stage, the CV value was small and changed slowly,whereas at the later nonuniform deformation stage, the CV value increased sharply and changed abruptly. Therefore, the precursor to a rock sample breakdown can be predicted by observing the variation characteristics of CV statistics. The correlation we found between our experimental and theoretical results revealed that our crack evolution and sample deformation results showed good coupling with seismic distribution characteristics near the San Andreas Fault.
