冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进...冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。展开更多
现有电力负荷预测方法面临诸多挑战,尤其是在考虑气象因素对负荷波动的影响时,传统方法往往忽视气象特征与负荷之间复杂的非线性关系,导致预测精度不足。对此文中提出一种基于气象相似日修正(meteorological similar day correction,MS...现有电力负荷预测方法面临诸多挑战,尤其是在考虑气象因素对负荷波动的影响时,传统方法往往忽视气象特征与负荷之间复杂的非线性关系,导致预测精度不足。对此文中提出一种基于气象相似日修正(meteorological similar day correction,MSDC)和改进鹦鹉优化(improved parrot optimizer,IPO)线性分解(decomposition-based linear,DLinear)的日前电力负荷预测模型。首先运用Logistic映射、自适应变异策略、螺旋波动搜索IPO对DLinear超参数进行优化,然后由DLinear提取数据的周期性和趋势性特征,最后通过比对气象特征欧氏距离修正负荷预测值,形成基于IPO-DLinear-MSDC的日前电力负荷预测模型。采用2024年6月至10月湖南株洲地区总电力负荷数据集进行仿真分析,IPO-DLinear-MSDC模型的输出平均绝对百分比误差(mean absolute percentage error,MAPE)、决定系数R2分别为4.67%、0.833,相较于IPO-DLinear与PO-DLinear模型,MAPE分别下降了0.83个百分点、1.43个百分点,R2分别提升了0.074、0.125。展开更多
Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and a...Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and astronomy.Here,we design and fabricate silicon nitride,dispersion-managed microresonators that effectively suppress avoided-mode crossings and achieve close-to-zero averaged dispersion.Both the stochastic noise and mode-locking dynamics of the resonator are numerically and experimentally investigated.First,we experimentally demonstrate thermally stabilized microcomb formation in the microresonator across different mode-locked states,showing negligible center frequency shifts and a broad frequency bandwidth.Next,we characterize the femtosecond timing jitter of the microcombs,supported by precise metrology of the timing phase and relative intensity noise.For the single-soliton state,we report a relative intensity noise of−153.2 dB∕Hz,close to the shot-noise limit,and a quantum-noise–limited timing jitter power spectral density of 0.4 as 2∕Hz at a 100 kHz offset frequency,measured using a self-heterodyne linear interferometer.In addition,we achieve an integrated timing jitter of 1.7 fs±0.07 fs,measured from 10 kHz to 1 MHz.Measuring and understanding these fundamental noise parameters in high clock rate frequency microcombs is critical for advancing soliton physics and enabling new applications in precision metrology.展开更多
Two new linear furocoumarins were isolated from Notopterygium incisum using silica gel,gel Sephadex LH-20 column chromatography,and preparative high-performance liquid chromatography.The structures of the new compound...Two new linear furocoumarins were isolated from Notopterygium incisum using silica gel,gel Sephadex LH-20 column chromatography,and preparative high-performance liquid chromatography.The structures of the new compounds were elucidated through analysis of spectroscopic evidence,including data obtained from high-resolution electrospray ionization mass spectrometry(HRESIMS)and nuclear magnetic resonance(NMR).The absolute configurations of Notoprenylate L(1)and Nototerprinol K(2)were further confirmed using electronic circular dichroism(ECD)calculations.Compound 1 demonstrated the ability to inhibit the expression of nitric oxide(NO),a pro-inflammatory factor,in lipopolysaccharide-induced RAW264.7 macrophages at a concentration of 7.5μmol/L,indicating its potential for anti-inflammatory activity.展开更多
The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from...The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).展开更多
Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance ...Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance and scalability,as current trends require the distribution of computation across network nodes/points.In this paper,we survey a large number of mapping and scheduling techniques designed for NoC architectures.This time,we concentrated on 3D systems.We take a systematic literature review approach to analyze existing methods across static,dynamic,hybrid,and machine-learning-based approaches,alongside preliminary AI-based dynamic models in recent works.We classify them into several main aspects covering power-aware mapping,fault tolerance,load-balancing,and adaptive for dynamic workloads.Also,we assess the efficacy of each method against performance parameters,such as latency,throughput,response time,and error rate.Key challenges,including energy efficiency,real-time adaptability,and reinforcement learning integration,are highlighted as well.To the best of our knowledge,this is one of the recent reviews that identifies both traditional and AI-based algorithms for mapping over a modern NoC,and opens research challenges.Finally,we provide directions for future work toward improved adaptability and scalability via lightweight learned models and hierarchical mapping frameworks.展开更多
The growing prevalence of exercise-induced tibial stress fractures demands wearable sensors capable of monitoring dynamic musculoskeletal loads with medical-grade precision.While flexible pressure-sensing insoles show...The growing prevalence of exercise-induced tibial stress fractures demands wearable sensors capable of monitoring dynamic musculoskeletal loads with medical-grade precision.While flexible pressure-sensing insoles show clinical potential,their development has been hindered by the intrinsic trade-off between high sensitivity and full-range linearity(R^(2)>0.99 up to 1 MPa)in conventional designs.Inspired by the tactile sensing mechanism of human skin,where dermal stratification enables wide-range pressure adaptation and ion-channelregulated signaling maintains linear electrical responses,we developed a dual-mechanism flexible iontronic pressure sensor(FIPS).This innovative design synergistically combines two bioinspired components:interdigitated fabric microstructures enabling pressure-proportional contact area expansion(αP1/3)and iontronic film facilitating self-adaptive ion concentration modulation(αP^(2/3)),which together generate a linear capacitance-pressure response(CαP).The FIPS achieves breakthrough performance:242 kPa^(-1)sensitivity with 0.997linearity across 0-1 MPa,yielding a record linear sensing factor(LSF=242,000).The design is validated across various substrates and ionic materials,demonstrating its versatility.Finally,the FIPS-driven design enables a smart insole demonstrating 1.8%error in tibial load assessment during gait analysis,outperforming nonlinear counterparts(6.5%error)in early fracture-risk prediction.The biomimetic design framework establishes a universal approach for developing high-performance linear sensors,establishing generalized principles for medical-grade wearable devices.展开更多
In this paper,we study a class of Linear Fractional Programming on a nonempty bounded set,called the Problem(LFP),and design a branch and bound algorithm to find the global optimal solution of the problem(LFP).First,w...In this paper,we study a class of Linear Fractional Programming on a nonempty bounded set,called the Problem(LFP),and design a branch and bound algorithm to find the global optimal solution of the problem(LFP).First,we convert the problem(LFP)to the equivalent problem(EP2).Secondly,by applying the linear relaxation technique to the problem(EP2),the linear relaxation programming problem(LRP2Y)was obtained.Then,the overall framework of the algorithm is given,and the convergence and complexity of the algorithm are analyzed.Finally,experimental results are listed to illustrate the effectiveness of the algorithm.展开更多
文摘冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。
文摘现有电力负荷预测方法面临诸多挑战,尤其是在考虑气象因素对负荷波动的影响时,传统方法往往忽视气象特征与负荷之间复杂的非线性关系,导致预测精度不足。对此文中提出一种基于气象相似日修正(meteorological similar day correction,MSDC)和改进鹦鹉优化(improved parrot optimizer,IPO)线性分解(decomposition-based linear,DLinear)的日前电力负荷预测模型。首先运用Logistic映射、自适应变异策略、螺旋波动搜索IPO对DLinear超参数进行优化,然后由DLinear提取数据的周期性和趋势性特征,最后通过比对气象特征欧氏距离修正负荷预测值,形成基于IPO-DLinear-MSDC的日前电力负荷预测模型。采用2024年6月至10月湖南株洲地区总电力负荷数据集进行仿真分析,IPO-DLinear-MSDC模型的输出平均绝对百分比误差(mean absolute percentage error,MAPE)、决定系数R2分别为4.67%、0.833,相较于IPO-DLinear与PO-DLinear模型,MAPE分别下降了0.83个百分点、1.43个百分点,R2分别提升了0.074、0.125。
基金support from the Lawrence Livermore National Laboratory(Grant No.B622827)the National Science Foundation(Grant Nos.1824568,1810506,1741707,and 1829071)the Office of Naval Research(Grant No.N00014-16-1-2094).
文摘Laser frequency microcombs provide a series of equidistant,coherent frequency markers across a broad spectrum,enabling advancements in laser spectroscopy,dense optical communications,precision distance metrology,and astronomy.Here,we design and fabricate silicon nitride,dispersion-managed microresonators that effectively suppress avoided-mode crossings and achieve close-to-zero averaged dispersion.Both the stochastic noise and mode-locking dynamics of the resonator are numerically and experimentally investigated.First,we experimentally demonstrate thermally stabilized microcomb formation in the microresonator across different mode-locked states,showing negligible center frequency shifts and a broad frequency bandwidth.Next,we characterize the femtosecond timing jitter of the microcombs,supported by precise metrology of the timing phase and relative intensity noise.For the single-soliton state,we report a relative intensity noise of−153.2 dB∕Hz,close to the shot-noise limit,and a quantum-noise–limited timing jitter power spectral density of 0.4 as 2∕Hz at a 100 kHz offset frequency,measured using a self-heterodyne linear interferometer.In addition,we achieve an integrated timing jitter of 1.7 fs±0.07 fs,measured from 10 kHz to 1 MHz.Measuring and understanding these fundamental noise parameters in high clock rate frequency microcombs is critical for advancing soliton physics and enabling new applications in precision metrology.
文摘Two new linear furocoumarins were isolated from Notopterygium incisum using silica gel,gel Sephadex LH-20 column chromatography,and preparative high-performance liquid chromatography.The structures of the new compounds were elucidated through analysis of spectroscopic evidence,including data obtained from high-resolution electrospray ionization mass spectrometry(HRESIMS)and nuclear magnetic resonance(NMR).The absolute configurations of Notoprenylate L(1)and Nototerprinol K(2)were further confirmed using electronic circular dichroism(ECD)calculations.Compound 1 demonstrated the ability to inhibit the expression of nitric oxide(NO),a pro-inflammatory factor,in lipopolysaccharide-induced RAW264.7 macrophages at a concentration of 7.5μmol/L,indicating its potential for anti-inflammatory activity.
基金Sichuan Science and Technology Program(2025ZNSFSC1341)Fundamental Research Funds for the Central Universities(J2022-090,25CAFUC04087)。
文摘The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).
基金the Deanship of Graduate Studies and Scientific Research at University of Bisha for supporting this work through the Fast-Track Research Support Programthe Deanship of Scientific Research at Northern Border University,Arar,KSA for funding this research work through the project number“NBU-FFR-2025-2903-09”.
文摘Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance and scalability,as current trends require the distribution of computation across network nodes/points.In this paper,we survey a large number of mapping and scheduling techniques designed for NoC architectures.This time,we concentrated on 3D systems.We take a systematic literature review approach to analyze existing methods across static,dynamic,hybrid,and machine-learning-based approaches,alongside preliminary AI-based dynamic models in recent works.We classify them into several main aspects covering power-aware mapping,fault tolerance,load-balancing,and adaptive for dynamic workloads.Also,we assess the efficacy of each method against performance parameters,such as latency,throughput,response time,and error rate.Key challenges,including energy efficiency,real-time adaptability,and reinforcement learning integration,are highlighted as well.To the best of our knowledge,this is one of the recent reviews that identifies both traditional and AI-based algorithms for mapping over a modern NoC,and opens research challenges.Finally,we provide directions for future work toward improved adaptability and scalability via lightweight learned models and hierarchical mapping frameworks.
基金supported by the National Natural Science Foundation of China(NSFC 52175281,52475315)Youth Innovation Promotion Association of CAS(2021382)。
文摘The growing prevalence of exercise-induced tibial stress fractures demands wearable sensors capable of monitoring dynamic musculoskeletal loads with medical-grade precision.While flexible pressure-sensing insoles show clinical potential,their development has been hindered by the intrinsic trade-off between high sensitivity and full-range linearity(R^(2)>0.99 up to 1 MPa)in conventional designs.Inspired by the tactile sensing mechanism of human skin,where dermal stratification enables wide-range pressure adaptation and ion-channelregulated signaling maintains linear electrical responses,we developed a dual-mechanism flexible iontronic pressure sensor(FIPS).This innovative design synergistically combines two bioinspired components:interdigitated fabric microstructures enabling pressure-proportional contact area expansion(αP1/3)and iontronic film facilitating self-adaptive ion concentration modulation(αP^(2/3)),which together generate a linear capacitance-pressure response(CαP).The FIPS achieves breakthrough performance:242 kPa^(-1)sensitivity with 0.997linearity across 0-1 MPa,yielding a record linear sensing factor(LSF=242,000).The design is validated across various substrates and ionic materials,demonstrating its versatility.Finally,the FIPS-driven design enables a smart insole demonstrating 1.8%error in tibial load assessment during gait analysis,outperforming nonlinear counterparts(6.5%error)in early fracture-risk prediction.The biomimetic design framework establishes a universal approach for developing high-performance linear sensors,establishing generalized principles for medical-grade wearable devices.
基金Supported by the National Natural Science Foundation of China(Grant Nos.12571317 and 12071133).
文摘In this paper,we study a class of Linear Fractional Programming on a nonempty bounded set,called the Problem(LFP),and design a branch and bound algorithm to find the global optimal solution of the problem(LFP).First,we convert the problem(LFP)to the equivalent problem(EP2).Secondly,by applying the linear relaxation technique to the problem(EP2),the linear relaxation programming problem(LRP2Y)was obtained.Then,the overall framework of the algorithm is given,and the convergence and complexity of the algorithm are analyzed.Finally,experimental results are listed to illustrate the effectiveness of the algorithm.
