The discrete iterative map model of peak current-mode controlled buck converter with constant current load（CCL）,containing the output voltage feedback and ramp compensation, is established in this paper. Based on th...The discrete iterative map model of peak current-mode controlled buck converter with constant current load（CCL）,containing the output voltage feedback and ramp compensation, is established in this paper. Based on this model the complex dynamics of this converter is investigated by analyzing bifurcation diagrams and the Lyapunov exponent spectrum. The effects of ramp compensation and output voltage feedback on the stability of the converter are investigated. Experimental results verify the simulation and theoretical analysis. The stability boundary and chaos boundary are obtained under the theoretical conditions of period-doubling bifurcation and border collision. It is found that there are four operation regions in the peak current-mode controlled buck converter with CCL due to period-doubling bifurcation and border-collision bifurcation. Research results indicate that ramp compensation can extend the stable operation range and transfer the operating mode, and output voltage feedback can eventually eliminate the coexisting fast-slow scale instability.展开更多
In ferroelectric liquid crystals, phase transitions can be induced by an electric field. The current constant method allows these transition to be quickly localized and thus the（E, T） phase diagram of the studied pr...In ferroelectric liquid crystals, phase transitions can be induced by an electric field. The current constant method allows these transition to be quickly localized and thus the（E, T） phase diagram of the studied product can be obtained.In this work, we make a slight modification to the measurement principles based on this method. This modification allows the characteristic parameters of ferroelectric liquid crystal to be quantitatively measured. The use of a current square signal highlights a phenomenon of ferroelectric hysteresis with remnant polarization at null field, which points out an effect of memory in this compound.展开更多
Conventional multi-stage constant current charging strategies often use higher multiples of current to charge the battery in pursuit of shorter charging times.However,this leads to an increase in battery temperature,w...Conventional multi-stage constant current charging strategies often use higher multiples of current to charge the battery in pursuit of shorter charging times.However,this leads to an increase in battery temperature,while shortening the charging time.This in turn affects the safety of the charging process.Furthermore,the higher charging currents are not ideal for shortening the charging time in the later stages of charging.To solve the aforementioned problems,in this study,a multi-stage constant current charging strategy is presented.This strategy can shorten the battery charging time by using the increase in battery temperature during the charging process as a constraint,using a genetic algorithm to calculate the charging current value,and investigating the phased approach to charging.Finally,the charging strategy is experimentally validated at different ambient temperatures and different initial SOCs.The experimental results show that the charging strategy proposed in this paper not only reduces the amount of calculations,but also reduces the temperature rise by up to 46.4%and charging time by up to 4.2%under different operating conditions.展开更多
Effective wind energy harvesting represents a viable solution to the global energy shortage and environmental pollution.Triboelectric nanogenerators(TENGs)hold great potential in wind energy harvesting;yet,there is li...Effective wind energy harvesting represents a viable solution to the global energy shortage and environmental pollution.Triboelectric nanogenerators(TENGs)hold great potential in wind energy harvesting;yet,there is little research on constant current TENGs for this purpose.Herein,a novel rotary bicharacteristic current TENG(R-BC-TENG)with constant current output for ambient wind energy harvesting is proposed,which delivers a low crest factor of 1.0187.Through the synergistic integration of triboelectrification,electrostatic discharge,and electrostatic induction,an average power density of 2.4 W m−2 Hz−1 and a charge density of 1.86 mC m−2 for the R-BC-TENG are achieved,with the charge density surpassing that reported in most previous studies.The minimum starting wind speed of R-BC-TENG is as low as 2.8 m s−1 while maintaining 100%performance after 12,700 cycles.Moreover,a self-powered air purification system,based on the R-BC-TENG,is developed,with the ability to generate 1,400,000 ions cm−3 and settle dust within 50 s.This work provides a paradigm for harvesting wind energy to achieve constant current output as well as safe and efficient air purification.展开更多
Lithium plating has been identified as the main form of failure in fast charging,so it is imperative to develop effective methods for detecting lithium plating.Experimental results validated the effectiveness of lithi...Lithium plating has been identified as the main form of failure in fast charging,so it is imperative to develop effective methods for detecting lithium plating.Experimental results validated the effectiveness of lithium plating detection via expansion force measurement.While multi-stage constant current(MCC)charging is a common form of fast charging,experimental investigations of lithium plating under MCC charging remain scarce,particularly lacking models to describe the battery expansion force changes during the lithium plating process under MCC conditions.The expansion of batteries during charging is caused by factors such as intercalation reactions,thermal expansion,and lithium plating.Through the establishment of the coupling model,the expansion displacement of the battery is calculated.The thermal expansion coefficient and equivalent stiffness of the battery are obtained through experiments,which are used to calculate the battery expansion force.Additionally,the battery overpotential is calculated through the model to determine the impact of lithium plating on the expansion force.The model investigates the effects of lithium plating on battery expansion force under different C-rates during constant current and MCC charging processes,achieving semi-quantitative prediction of battery expansion force under MCC charging and providing model-based optimization directions for MCC charging strategies.This work provides valuable insights for battery modeling and charging strategy optimization in terms of expansion force modeling under multi-stage constant current charging.展开更多
The conversion from constant current(CC)to constant voltage(CV)is one of the key technologies of CC underwater observatory systems.A shunt regulator with high stability and high reliability is usually used.Application...The conversion from constant current(CC)to constant voltage(CV)is one of the key technologies of CC underwater observatory systems.A shunt regulator with high stability and high reliability is usually used.Applications,however,are limited by high heat dissipation and low efficiency.In this paper,with an improved shunt regulation method,a novel concept of stepless power reconfiguration(SPR)for the CC/CV module is proposed.In cases with stable or slowly changing load,two modes of CC/CV conversion are proposed to reduce unnecessary power loss of the shunt regulator while being able to retain any operatorpreset power margin in the system:(1)the manual SPR(MSPR)method based on single-loop control method;(2)the automatic SPR(ASPR)method based on inner-outer loop control method.The efficiency of the system is analyzed.How to select some key parameters of the system is discussed.Experimental results show that MSPR and ASPR are both effective and practical methods to reduce heat dissipation and improve the efficiency of the CC/CV module,while the high stability of the shunt regulator remains.展开更多
The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/disch...The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/discharge rates and intermittent discharge experiment are discussed. Though the d t /d E ? 獷 plot is affected by many factors, it clearly has intrinsic relation with the nature of active material such as conductivity and thermodynamic potential of active material, which changes with the state of charge. The d t /d E—E plot can also be applied to other electrochemical active materials, especially to those having several phases during charge or discharge.展开更多
The hysteresis control combined with PWM control non-inverting buck-boost was proposed to improve the light load efficiency and power density.The constant inductor current control(CICC)was established to mitigate the ...The hysteresis control combined with PWM control non-inverting buck-boost was proposed to improve the light load efficiency and power density.The constant inductor current control(CICC)was established to mitigate the dependence on the external components and device variation and make smooth transition between hysteresis control loop and pulse width modulation(PWM)control loop.The small signal model was deduced for the buck and boost operation mode.The inductor current slope control(ICSC)was proposed to implement the automatic mode transition between buck and boost mode in one switching cycle.The results show that the converter prototype has good dynamic response capability,achieving 94%efficiency and 95%peak efficiency at full 10 A load current.展开更多
An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we...An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we have developed a simple response compensation scheme based on a precise theoretical expression for the frequency response of the CCA (Kaifuku et al. 2010, 2011), and verified its effectiveness experimentally for hot-wires of 5 μm, 10 μm and 20 μm in diameter. Then, another novel technique based on a two-sensor probe technique—originally developed for the response compensation of fine-wire thermocouples (Tagawa and Ohta 1997;Tagawa et al. 1998)—has been proposed for estimating thermal time-constants of hot-wires to realize the in-situ response compensation of the CCA. To demonstrate the usefulness of the CCA, we have applied the response compensation schemes to multipoint velocity measure- ment of a turbulent wake flow formed behind a circular cylinder by using a CCA probe consisting of 16 hot-wires, which were driven simultaneously by a very simple constant-current circuit. As a result, the proposed response compensation techniques for the CCA work quite successfully and are capable of improving the response speed of the CCA to obtain reliable measurements comparable to those by the commercially-available constant-temperature hot-wire anemometer (CTA).展开更多
The adapted DC-DC converters should be smaller in size and have a small output current ripple to meet the increasing demand for low voltages with high performance and high density micro processors for several microele...The adapted DC-DC converters should be smaller in size and have a small output current ripple to meet the increasing demand for low voltages with high performance and high density micro processors for several microelectronic load applications. This paper proposes a DC-DC converter using variable on-time and variable switching frequency control enhanced constant ripple current control and reduced magnetic components. The proposed converter is realized by making the turn-offtime proportional to the on-time of the converter, according to the input and output voltage, thereby reducing the corresponding current ripple on output voltage in the continuous conduction mode. A Buck DC-DC converter using the proposed control strategy is analyzed in detail, along with some experimental results to show the performance and effectiveness of this converter.展开更多
The low voltage substrate current （Ib） has been studied based on generation kinetics and used as a monitor of interface states （Nit） generation for ultra-thin oxide n-MOSFETs under constant voltage stress. It is f...The low voltage substrate current （Ib） has been studied based on generation kinetics and used as a monitor of interface states （Nit） generation for ultra-thin oxide n-MOSFETs under constant voltage stress. It is found that the low voltage Ib is formed by electrons tunnelling through interface states, and the variations of Ib（△Ib） are proportional to variations of Nit （△Nit）. The Nit energy distributions were determined by differentiating Nit（Vg）. The results have been compared with that measured by using gate diode technique.展开更多
The present numerically study investigates the influence of the Hall current and constant heat flux on the Magneto hydrodynamic (MHD) natural convection boundary layer viscous incompressible fluid flow in the manifest...The present numerically study investigates the influence of the Hall current and constant heat flux on the Magneto hydrodynamic (MHD) natural convection boundary layer viscous incompressible fluid flow in the manifestation of transverse magnetic field near an inclined vertical permeable flat plate. It is assumed that the induced magnetic field is negligible compared with the imposed magnetic field. The governing boundary layer equations have been transferred into non-similar model by implementing similarity approaches. The physical dimensionless parameter has been set up into the model as Prandtl number, Eckert number, Magnetic parameter, Schmidt number, local Grashof number and local modified Grashof number. The numerical method of Nactsheim-Swigert shooting iteration technique together with Runge-Kutta six order iteration scheme has been used to solve the system of governing non-similar equations. The physical effects of the various parameters on dimensionless primary velocity profile, secondary velocity profile, and temperature and concentration profile are discussed graphically. Moreover, the local skin friction coefficient, the local Nusselt number and Sherwood number are shown in tabular form for various values of the parameters.展开更多
The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the ...The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.展开更多
An error back propagation （BP） neural network prediction model was established for the shunt current compensation in series resistance spot welding. The input variables for the neural network consist of the resistiv...An error back propagation （BP） neural network prediction model was established for the shunt current compensation in series resistance spot welding. The input variables for the neural network consist of the resistivity of the material, the thickness of workpiece and the spot spacing, and the shunt rate is outputted. A simplified calculation for the shunt rate was presented based on the feature of the constant-current resistance spot welding and the variation of the resistance in resistance spot welding process, and then the data generated by simplified calculation were used to train and adjust the neural network model. The neural network model proposed was used to predict the shunt rate in the spot welding of 20# mlid steel （in Chinese classification） （in 2. 0 mm thickness） and 10# mild steel （in 1.5 mm and 1.0 mm thickness）. The maximum relative prediction errors are, respectively, 2. 83%, 1.77% and 3.67%. Shunt current compensation experiments were peoCormed based on the neural network prediction model proposed to check the diameter difference of nuggets. Experimental results show that maximum nugget diameter deviation is less than 4% for both 10# and 20# mlid steels with spot spacing of 30 mm and 50 mm.展开更多
Improving the temperature stability and widening the constant current range are two important problems to be solved in the application of the current regulators. This paper introduces a modular approach for the design...Improving the temperature stability and widening the constant current range are two important problems to be solved in the application of the current regulators. This paper introduces a modular approach for the design of the current regulator with a very wide current range. The test results show that their output current ranges from 0.1A to 8A, with its current temperature coefficient as low as 10-4/℃ to 10-5/℃ and limiting voltage lower than 0.4V.展开更多
The change of the over-current protection point of the power switches, caused by slope compensation, is analyzed in detail. It is discovered that the peak current protecting value increases as the duty cycle decreases...The change of the over-current protection point of the power switches, caused by slope compensation, is analyzed in detail. It is discovered that the peak current protecting value increases as the duty cycle decreases. As a result, the safety operation of the switches is damaged greatly. A novel solution to improve over-current protection with constant peak current limitation is proposed by inducing synchronous slope compensation into the current limit function instead of the original constant voltage. The design principle and method of the protection circuit based on a UC3846 PWM controller for the interleaved dual-forward converter is presented. Experimental results are given to verify the analysis.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant No.61371033)the Fok Ying-Tung Education Foundation for Young Teachers in the Higher Education Institutions of China(Grant No.142027)+1 种基金the Sichuan Provincial Youth Science and Technology Fund,China(Grant Nos.2014JQ0015and 2013JQ0033)the Fundamental Research Funds for the Central Universities,China(Grant No.SWJTU11CX029)
文摘The discrete iterative map model of peak current-mode controlled buck converter with constant current load（CCL）,containing the output voltage feedback and ramp compensation, is established in this paper. Based on this model the complex dynamics of this converter is investigated by analyzing bifurcation diagrams and the Lyapunov exponent spectrum. The effects of ramp compensation and output voltage feedback on the stability of the converter are investigated. Experimental results verify the simulation and theoretical analysis. The stability boundary and chaos boundary are obtained under the theoretical conditions of period-doubling bifurcation and border collision. It is found that there are four operation regions in the peak current-mode controlled buck converter with CCL due to period-doubling bifurcation and border-collision bifurcation. Research results indicate that ramp compensation can extend the stable operation range and transfer the operating mode, and output voltage feedback can eventually eliminate the coexisting fast-slow scale instability.
文摘In ferroelectric liquid crystals, phase transitions can be induced by an electric field. The current constant method allows these transition to be quickly localized and thus the（E, T） phase diagram of the studied product can be obtained.In this work, we make a slight modification to the measurement principles based on this method. This modification allows the characteristic parameters of ferroelectric liquid crystal to be quantitatively measured. The use of a current square signal highlights a phenomenon of ferroelectric hysteresis with remnant polarization at null field, which points out an effect of memory in this compound.
基金supported by National Natural Science Foundation of China (Grant No. 51677058)
文摘Conventional multi-stage constant current charging strategies often use higher multiples of current to charge the battery in pursuit of shorter charging times.However,this leads to an increase in battery temperature,while shortening the charging time.This in turn affects the safety of the charging process.Furthermore,the higher charging currents are not ideal for shortening the charging time in the later stages of charging.To solve the aforementioned problems,in this study,a multi-stage constant current charging strategy is presented.This strategy can shorten the battery charging time by using the increase in battery temperature during the charging process as a constraint,using a genetic algorithm to calculate the charging current value,and investigating the phased approach to charging.Finally,the charging strategy is experimentally validated at different ambient temperatures and different initial SOCs.The experimental results show that the charging strategy proposed in this paper not only reduces the amount of calculations,but also reduces the temperature rise by up to 46.4%and charging time by up to 4.2%under different operating conditions.
基金supported by the National Natural Science Foundation of China(Grant Nos.52076024 and 52572203)the Natural Science Foundation of Chongqing(Grant No.cstc2021jcyj-msxmX0625)the Fundamental Research Funds for Central Universities(Grant Nos.2023CDJXY-0049 and 2025CDJ-IAISYB-030).
文摘Effective wind energy harvesting represents a viable solution to the global energy shortage and environmental pollution.Triboelectric nanogenerators(TENGs)hold great potential in wind energy harvesting;yet,there is little research on constant current TENGs for this purpose.Herein,a novel rotary bicharacteristic current TENG(R-BC-TENG)with constant current output for ambient wind energy harvesting is proposed,which delivers a low crest factor of 1.0187.Through the synergistic integration of triboelectrification,electrostatic discharge,and electrostatic induction,an average power density of 2.4 W m−2 Hz−1 and a charge density of 1.86 mC m−2 for the R-BC-TENG are achieved,with the charge density surpassing that reported in most previous studies.The minimum starting wind speed of R-BC-TENG is as low as 2.8 m s−1 while maintaining 100%performance after 12,700 cycles.Moreover,a self-powered air purification system,based on the R-BC-TENG,is developed,with the ability to generate 1,400,000 ions cm−3 and settle dust within 50 s.This work provides a paradigm for harvesting wind energy to achieve constant current output as well as safe and efficient air purification.
基金financially supported by the National Natural Science Foundation of China(No.52207242).
文摘Lithium plating has been identified as the main form of failure in fast charging,so it is imperative to develop effective methods for detecting lithium plating.Experimental results validated the effectiveness of lithium plating detection via expansion force measurement.While multi-stage constant current(MCC)charging is a common form of fast charging,experimental investigations of lithium plating under MCC charging remain scarce,particularly lacking models to describe the battery expansion force changes during the lithium plating process under MCC conditions.The expansion of batteries during charging is caused by factors such as intercalation reactions,thermal expansion,and lithium plating.Through the establishment of the coupling model,the expansion displacement of the battery is calculated.The thermal expansion coefficient and equivalent stiffness of the battery are obtained through experiments,which are used to calculate the battery expansion force.Additionally,the battery overpotential is calculated through the model to determine the impact of lithium plating on the expansion force.The model investigates the effects of lithium plating on battery expansion force under different C-rates during constant current and MCC charging processes,achieving semi-quantitative prediction of battery expansion force under MCC charging and providing model-based optimization directions for MCC charging strategies.This work provides valuable insights for battery modeling and charging strategy optimization in terms of expansion force modeling under multi-stage constant current charging.
基金Project supported by the National Natural Science Foundation of China(No.51979246)the Ningbo Science and Technology Innovation 2025 Major Special Project,China(No.2020Z075)。
文摘The conversion from constant current(CC)to constant voltage(CV)is one of the key technologies of CC underwater observatory systems.A shunt regulator with high stability and high reliability is usually used.Applications,however,are limited by high heat dissipation and low efficiency.In this paper,with an improved shunt regulation method,a novel concept of stepless power reconfiguration(SPR)for the CC/CV module is proposed.In cases with stable or slowly changing load,two modes of CC/CV conversion are proposed to reduce unnecessary power loss of the shunt regulator while being able to retain any operatorpreset power margin in the system:(1)the manual SPR(MSPR)method based on single-loop control method;(2)the automatic SPR(ASPR)method based on inner-outer loop control method.The efficiency of the system is analyzed.How to select some key parameters of the system is discussed.Experimental results show that MSPR and ASPR are both effective and practical methods to reduce heat dissipation and improve the efficiency of the CC/CV module,while the high stability of the shunt regulator remains.
文摘The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/discharge rates and intermittent discharge experiment are discussed. Though the d t /d E ? 獷 plot is affected by many factors, it clearly has intrinsic relation with the nature of active material such as conductivity and thermodynamic potential of active material, which changes with the state of charge. The d t /d E—E plot can also be applied to other electrochemical active materials, especially to those having several phases during charge or discharge.
文摘The hysteresis control combined with PWM control non-inverting buck-boost was proposed to improve the light load efficiency and power density.The constant inductor current control(CICC)was established to mitigate the dependence on the external components and device variation and make smooth transition between hysteresis control loop and pulse width modulation(PWM)control loop.The small signal model was deduced for the buck and boost operation mode.The inductor current slope control(ICSC)was proposed to implement the automatic mode transition between buck and boost mode in one switching cycle.The results show that the converter prototype has good dynamic response capability,achieving 94%efficiency and 95%peak efficiency at full 10 A load current.
文摘An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we have developed a simple response compensation scheme based on a precise theoretical expression for the frequency response of the CCA (Kaifuku et al. 2010, 2011), and verified its effectiveness experimentally for hot-wires of 5 μm, 10 μm and 20 μm in diameter. Then, another novel technique based on a two-sensor probe technique—originally developed for the response compensation of fine-wire thermocouples (Tagawa and Ohta 1997;Tagawa et al. 1998)—has been proposed for estimating thermal time-constants of hot-wires to realize the in-situ response compensation of the CCA. To demonstrate the usefulness of the CCA, we have applied the response compensation schemes to multipoint velocity measure- ment of a turbulent wake flow formed behind a circular cylinder by using a CCA probe consisting of 16 hot-wires, which were driven simultaneously by a very simple constant-current circuit. As a result, the proposed response compensation techniques for the CCA work quite successfully and are capable of improving the response speed of the CCA to obtain reliable measurements comparable to those by the commercially-available constant-temperature hot-wire anemometer (CTA).
文摘The adapted DC-DC converters should be smaller in size and have a small output current ripple to meet the increasing demand for low voltages with high performance and high density micro processors for several microelectronic load applications. This paper proposes a DC-DC converter using variable on-time and variable switching frequency control enhanced constant ripple current control and reduced magnetic components. The proposed converter is realized by making the turn-offtime proportional to the on-time of the converter, according to the input and output voltage, thereby reducing the corresponding current ripple on output voltage in the continuous conduction mode. A Buck DC-DC converter using the proposed control strategy is analyzed in detail, along with some experimental results to show the performance and effectiveness of this converter.
文摘The low voltage substrate current （Ib） has been studied based on generation kinetics and used as a monitor of interface states （Nit） generation for ultra-thin oxide n-MOSFETs under constant voltage stress. It is found that the low voltage Ib is formed by electrons tunnelling through interface states, and the variations of Ib（△Ib） are proportional to variations of Nit （△Nit）. The Nit energy distributions were determined by differentiating Nit（Vg）. The results have been compared with that measured by using gate diode technique.
文摘The present numerically study investigates the influence of the Hall current and constant heat flux on the Magneto hydrodynamic (MHD) natural convection boundary layer viscous incompressible fluid flow in the manifestation of transverse magnetic field near an inclined vertical permeable flat plate. It is assumed that the induced magnetic field is negligible compared with the imposed magnetic field. The governing boundary layer equations have been transferred into non-similar model by implementing similarity approaches. The physical dimensionless parameter has been set up into the model as Prandtl number, Eckert number, Magnetic parameter, Schmidt number, local Grashof number and local modified Grashof number. The numerical method of Nactsheim-Swigert shooting iteration technique together with Runge-Kutta six order iteration scheme has been used to solve the system of governing non-similar equations. The physical effects of the various parameters on dimensionless primary velocity profile, secondary velocity profile, and temperature and concentration profile are discussed graphically. Moreover, the local skin friction coefficient, the local Nusselt number and Sherwood number are shown in tabular form for various values of the parameters.
文摘The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.
基金Acknowledgements The authors would like to thank for the financial support from the National Natural Science Foundation of China through document 51275418. The authors would also like to acknowledge professor Yang Siqian for providing discussion of the results for this study.
文摘An error back propagation （BP） neural network prediction model was established for the shunt current compensation in series resistance spot welding. The input variables for the neural network consist of the resistivity of the material, the thickness of workpiece and the spot spacing, and the shunt rate is outputted. A simplified calculation for the shunt rate was presented based on the feature of the constant-current resistance spot welding and the variation of the resistance in resistance spot welding process, and then the data generated by simplified calculation were used to train and adjust the neural network model. The neural network model proposed was used to predict the shunt rate in the spot welding of 20# mlid steel （in Chinese classification） （in 2. 0 mm thickness） and 10# mild steel （in 1.5 mm and 1.0 mm thickness）. The maximum relative prediction errors are, respectively, 2. 83%, 1.77% and 3.67%. Shunt current compensation experiments were peoCormed based on the neural network prediction model proposed to check the diameter difference of nuggets. Experimental results show that maximum nugget diameter deviation is less than 4% for both 10# and 20# mlid steels with spot spacing of 30 mm and 50 mm.
文摘Improving the temperature stability and widening the constant current range are two important problems to be solved in the application of the current regulators. This paper introduces a modular approach for the design of the current regulator with a very wide current range. The test results show that their output current ranges from 0.1A to 8A, with its current temperature coefficient as low as 10-4/℃ to 10-5/℃ and limiting voltage lower than 0.4V.
文摘The change of the over-current protection point of the power switches, caused by slope compensation, is analyzed in detail. It is discovered that the peak current protecting value increases as the duty cycle decreases. As a result, the safety operation of the switches is damaged greatly. A novel solution to improve over-current protection with constant peak current limitation is proposed by inducing synchronous slope compensation into the current limit function instead of the original constant voltage. The design principle and method of the protection circuit based on a UC3846 PWM controller for the interleaved dual-forward converter is presented. Experimental results are given to verify the analysis.
