Baosteel has excelled in automotive steel sheets in the past three decades.It has made a significant contribution to the development of China’s automotive industry by producing a wide range of high-quality steel prod...Baosteel has excelled in automotive steel sheets in the past three decades.It has made a significant contribution to the development of China’s automotive industry by producing a wide range of high-quality steel products.Some milestones achieved by Baosteel automotive steel sheet were briefly reviewed.The current challenges in producing ultra-high strength steel(UHSS),especially hot-dip galvanized UHSS,were summarized.The most current advancements in UHSS and the corresponding hot-dip galvanizing processes were discussed.The galvanizability of Si-Mn-added QP steel and DP steel, Mn-added TWIP steel, and Al-added low-density steel has been improved by different techniques in Baosteel.展开更多
The ultra-high-strength steel （UHSS） plays an important role in the mechanical industry because of their special performances. The machinability of 30CrMnSiNi2A steel was studied in dry milling with two different co...The ultra-high-strength steel （UHSS） plays an important role in the mechanical industry because of their special performances. The machinability of 30CrMnSiNi2A steel was studied in dry milling with two different coated tools in the present work. This paper introduced that 30CrMnSiNi2A steel was a kind of diffficult-to-machine materials. The results showed that the cutting force components of feed direction and cutting width direction, i.e. Fx and Fy, increased slightly with increasing the cutting speed and feed rate. The values of axial force component Fx were much larger than Fx and Fy, and increased obviously with increasing the milling speed. The workpiece surface had the minimum roughness at the cutting speed of 150 m/min. The physical vapor deposition （PVD） coated （（Ti, A1）N-TiN） insert was more suitable for machining 30CrMnSiNi2A steel than the chemical vapor deposition （CVD） coated （Ti（C, N）-Al2O3） insert. Moreover, the main failure modes of PVD-coated insert were micro-chipping and coating spalling. The wear modes of CVD-coated insert were ploughing, coating spalling, and cratering. The serious adhesive wear and the abrasion with some adhesion were the main wear mechanism of PVD- and CVD-coated inserts, respectively.展开更多
Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its...Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its applications on the prediction of sheet forming process. Then, a new macroscopic constitutive model is introduced, which possesses an enhanced description capacity of tension/compression anisotropy and anisotropic hardening. In order to take into account the twinning process of hexagonal close-packed material, a modified hierarchical multi-scale model is also established with adequate accuracy in a shorter computational time. The advanced forming limit of sheet metal, mainly about aluminum alloy, is also investigated. Besides the above theory developments, some new sheet metal forming technologies are reviewed simultaneously. The warm forming technology of Mg alloy is discussed. New processes to form sheet parts and to bend tubes are proposed by using hard granules. On the other hand, a new kind of ultra-high-strength steel based on typical22 Mn B5 by introducing more residual austenite and Cu-rich phase to increase the elongation and strength and its novel forming method that integrates hot stamping and quenching participation are proposed. Progresses in sheet hydroforming,press forging and electromagnetic forming of sheet metal parts are also summarized.展开更多
Bainite, the main microstructure of ultrahigh-strength complex-phase(CP) sheet steel, usually exhibits various micro-morphologies when subjected to different austempering treatments.In the current study, conventional ...Bainite, the main microstructure of ultrahigh-strength complex-phase(CP) sheet steel, usually exhibits various micro-morphologies when subjected to different austempering treatments.In the current study, conventional austempering treatment at the bainite nose temperature resulted in two bainite types with distinct micro-morphologies: polygonal blocky bainite and acicular bainite, which resulted in large fluctuations in the mechanical properties of CP steel, particularly yield strength and hole expansion ratio.Therefore, the precise control of bainite micro-morphology was studied and applied to separate the two bainite types through austempering optimization.The two bainite types of different micro-morphologies had different effects on the mechanical properties of CP steel: the acicular bainite favored hole expansion and flangeability but deteriorated ductility, while the polygonal blocky bainite favored ductility but deteriorated hole expansion and flangeability.Accordingly, two types of ultrahigh-strength CP steels of different mechanical properties can be stably manufactured through the precise control of bainitic micro-morphology to satisfy the specific demands of vehicle components in terms of the mechanical properties of CP steels.展开更多
This paper investigated an experimental method for bake hardening properties, a technique for deriving the true stress-strain curves after reaching the maximum load, and a constitutive equation considering both work h...This paper investigated an experimental method for bake hardening properties, a technique for deriving the true stress-strain curves after reaching the maximum load, and a constitutive equation considering both work hardening and bake hardening in order to apply the work hardening occurring in the forming process of parts and the bake hardening induced in the baking process to an automotive crash simulation. A general bake hardening test is that a pre-tensioned specimen is baked and then the same specimen is tensioned again without any further treatment. For a bake hardening test of automotive steel with a tensile strength of 1.2 GPa or more, fractures often occur in curvature section outside, an extensometer due to the difference in the material strength caused by non-uniform bake hardening. This causes a problem in that the bake hardening properties cannot be obtained. In this paper, to prevent curvature fracture, tensile specimens were re-machined in the uniformly deformed region of large specimens subjected to pre-strain, and the re-machined specimens with uniform strength in all regions were re-tensioned. In the bake hardening test of ultra-high strength steels with a tensile strength of 1 GPa or more, shear band fractures occur when the pre-strain is large. This makes it impossible to obtain a true stress-strain curve because there is no uniformly deformed region under a tensile test. To overcome this problem, a new method to calculate the true stress-strain curve by comparing experimental results and the load calculated by the local strain obtained from digital images was developed. This method can be applied not only where shear band deformation occurs, but also in necking deformation, and true stress-strain curves for strains up to 2 - 3 times the uniform elongation can be obtained. A new constitutive equation was developed since an appropriate hardening model is required to simultaneously apply the work hardening and the bake hardening to the simulation. For the newly developed model, the user material subroutine of LS-Dyna was configured, and the simulation was performed on the single hat specimens with pre-strain. When both work hardening and bake hardening were considered, there was a significant increase in absorbed energy compared to when only work hardening was considered. This means that both work hardening and bake hardening should be considered in the car crash simulations to enhance the accuracy of the simulation.展开更多
文摘Baosteel has excelled in automotive steel sheets in the past three decades.It has made a significant contribution to the development of China’s automotive industry by producing a wide range of high-quality steel products.Some milestones achieved by Baosteel automotive steel sheet were briefly reviewed.The current challenges in producing ultra-high strength steel(UHSS),especially hot-dip galvanized UHSS,were summarized.The most current advancements in UHSS and the corresponding hot-dip galvanizing processes were discussed.The galvanizability of Si-Mn-added QP steel and DP steel, Mn-added TWIP steel, and Al-added low-density steel has been improved by different techniques in Baosteel.
基金the Important National Science&Technology Specific Project(No.2013ZX04009-031)
文摘The ultra-high-strength steel （UHSS） plays an important role in the mechanical industry because of their special performances. The machinability of 30CrMnSiNi2A steel was studied in dry milling with two different coated tools in the present work. This paper introduced that 30CrMnSiNi2A steel was a kind of diffficult-to-machine materials. The results showed that the cutting force components of feed direction and cutting width direction, i.e. Fx and Fy, increased slightly with increasing the cutting speed and feed rate. The values of axial force component Fx were much larger than Fx and Fy, and increased obviously with increasing the milling speed. The workpiece surface had the minimum roughness at the cutting speed of 150 m/min. The physical vapor deposition （PVD） coated （（Ti, A1）N-TiN） insert was more suitable for machining 30CrMnSiNi2A steel than the chemical vapor deposition （CVD） coated （Ti（C, N）-Al2O3） insert. Moreover, the main failure modes of PVD-coated insert were micro-chipping and coating spalling. The wear modes of CVD-coated insert were ploughing, coating spalling, and cratering. The serious adhesive wear and the abrasion with some adhesion were the main wear mechanism of PVD- and CVD-coated inserts, respectively.
文摘Developments of new sheet metal forming technology and theory in China are reviewed in detail in this paper.Advances of crystal plasticity on the deformation mechanism of Mg alloy are firstly described, especially its applications on the prediction of sheet forming process. Then, a new macroscopic constitutive model is introduced, which possesses an enhanced description capacity of tension/compression anisotropy and anisotropic hardening. In order to take into account the twinning process of hexagonal close-packed material, a modified hierarchical multi-scale model is also established with adequate accuracy in a shorter computational time. The advanced forming limit of sheet metal, mainly about aluminum alloy, is also investigated. Besides the above theory developments, some new sheet metal forming technologies are reviewed simultaneously. The warm forming technology of Mg alloy is discussed. New processes to form sheet parts and to bend tubes are proposed by using hard granules. On the other hand, a new kind of ultra-high-strength steel based on typical22 Mn B5 by introducing more residual austenite and Cu-rich phase to increase the elongation and strength and its novel forming method that integrates hot stamping and quenching participation are proposed. Progresses in sheet hydroforming,press forging and electromagnetic forming of sheet metal parts are also summarized.
文摘Bainite, the main microstructure of ultrahigh-strength complex-phase(CP) sheet steel, usually exhibits various micro-morphologies when subjected to different austempering treatments.In the current study, conventional austempering treatment at the bainite nose temperature resulted in two bainite types with distinct micro-morphologies: polygonal blocky bainite and acicular bainite, which resulted in large fluctuations in the mechanical properties of CP steel, particularly yield strength and hole expansion ratio.Therefore, the precise control of bainite micro-morphology was studied and applied to separate the two bainite types through austempering optimization.The two bainite types of different micro-morphologies had different effects on the mechanical properties of CP steel: the acicular bainite favored hole expansion and flangeability but deteriorated ductility, while the polygonal blocky bainite favored ductility but deteriorated hole expansion and flangeability.Accordingly, two types of ultrahigh-strength CP steels of different mechanical properties can be stably manufactured through the precise control of bainitic micro-morphology to satisfy the specific demands of vehicle components in terms of the mechanical properties of CP steels.
文摘This paper investigated an experimental method for bake hardening properties, a technique for deriving the true stress-strain curves after reaching the maximum load, and a constitutive equation considering both work hardening and bake hardening in order to apply the work hardening occurring in the forming process of parts and the bake hardening induced in the baking process to an automotive crash simulation. A general bake hardening test is that a pre-tensioned specimen is baked and then the same specimen is tensioned again without any further treatment. For a bake hardening test of automotive steel with a tensile strength of 1.2 GPa or more, fractures often occur in curvature section outside, an extensometer due to the difference in the material strength caused by non-uniform bake hardening. This causes a problem in that the bake hardening properties cannot be obtained. In this paper, to prevent curvature fracture, tensile specimens were re-machined in the uniformly deformed region of large specimens subjected to pre-strain, and the re-machined specimens with uniform strength in all regions were re-tensioned. In the bake hardening test of ultra-high strength steels with a tensile strength of 1 GPa or more, shear band fractures occur when the pre-strain is large. This makes it impossible to obtain a true stress-strain curve because there is no uniformly deformed region under a tensile test. To overcome this problem, a new method to calculate the true stress-strain curve by comparing experimental results and the load calculated by the local strain obtained from digital images was developed. This method can be applied not only where shear band deformation occurs, but also in necking deformation, and true stress-strain curves for strains up to 2 - 3 times the uniform elongation can be obtained. A new constitutive equation was developed since an appropriate hardening model is required to simultaneously apply the work hardening and the bake hardening to the simulation. For the newly developed model, the user material subroutine of LS-Dyna was configured, and the simulation was performed on the single hat specimens with pre-strain. When both work hardening and bake hardening were considered, there was a significant increase in absorbed energy compared to when only work hardening was considered. This means that both work hardening and bake hardening should be considered in the car crash simulations to enhance the accuracy of the simulation.
