期刊文献+

离子氮碳共渗中氮对化合物层的影响 被引量:6

Influence of Nitrogen on Compound Layer in Ion Nitrocaburizing
在线阅读 下载PDF
导出
摘要 研究了在离子氮碳共渗过程中氮对化合物层厚度的影响,同时对化合物层的微观组织结构和显微硬度进行了分析。结果表明:在离子氮碳共渗过程中,气氛中低氮势不利于ε相的生成,且渗层的显微硬度较低;高氮势有利于ε相的生成,同时提高了渗层的显微硬度;当氮势超过60 %后对化合物层厚度影响不大。 The influence of nitrogen on the thickness of compound layer in plasma nitrocarburizing process was investigated. The microstucture and microhardness of compound layer were analyzed. The experiment results showed that high nitrogen potential in atmosphere can increase the compound layer thickness while low nitrogen potential in atmosphere will decrease the compound layer thickness and hardness. But excessive nitrogen has no influence on the thickness of compound layer.
出处 《中国表面工程》 EI CAS CSCD 2003年第6期24-26,共3页 China Surface Engineering
基金 青岛市科委重点科研项目(10-110-100-003)
关键词 离子氮碳共渗 氮势 化合物层 厚度 plasma nitrocarburizing nitrogen potential compound layer thickness
  • 相关文献

参考文献5

二级参考文献11

  • 1赵细金.氮势、可控渗氮与计算[J].机械工艺师,1993(1):19-22. 被引量:2
  • 2邓光华.热循环离子渗氮及其强渗作用[J].金属热处理,1995,20(11):8-10. 被引量:9
  • 3陈宗柱 高树香.气体导电(上册)[M].南京:南京工学院出版社,1988.54.
  • 4钟厉.变温快速深层离子氮化工艺及机理的研究:硕士论文[D].重庆:重庆大学,1992:74.
  • 5陈志远.氮基气氛热处理[M].北京:机械工业出版社,1989.10.
  • 6徐冰仲 张颖智.离子氮化氮的渗入机理.金属热处理,1983,(10):29-29.
  • 7全国气体分离设备科技信息网PSA分网第二次学术交流会论文集[C].杭州制氧机研究所,1999,4.
  • 8陈天民,热处理设计简明手册,1993年,11页
  • 9雷天同,金属热处理,1988年,4期
  • 10周上祺,金属热处理,1993年,3期,40页

共引文献56

同被引文献97

  • 1刘洪喜,汤宝寅,王浪平,王小峰,王宇航,于永澔.2Cr13钢的全方位离子注入与离子束增强沉积复合表面强化处理[J].航空材料学报,2005,25(2):32-37. 被引量:8
  • 2雷明凯,朱雪梅.奥氏体不锈钢磨损腐蚀复合改性技术[J].机械工人(热加工),2005,29(9):39-42. 被引量:3
  • 3王铁,周上祺,周安若,任勤,刘林飞,孔纪兰.空气-乙炔碳氮氧离子多元共渗工艺研究[J].热加工工艺,2006,35(8):62-64. 被引量:6
  • 4徐冰仲 张颖智.离子氮化氮的渗入机理.金属热处理,1983,(10):29-29.
  • 5Lo K H, Shek C H, Lai J K L. Recent developments in stainless steels [J]. Mater Sci Eng R, 2009, 65(4-6) : 39-104.
  • 6Kochmahski P, Nowacki J. Activaled gas nitriding of 17-4PH stainless steel[ J ]. Surf Coat Technol, 2006, 200 : 6558-6562.
  • 7Pinedo C E, Monteiro W A. On the kinetics of plasma nitriding a martensitic stainless steel type AISI 420 [ J ]. Surf Coat Technol, 2004,179(2/3): 119-123.
  • 8Suh B S, Lee W J. Surface hardening of AISI 316L stainless steel using plasma carburizing[ J]. Thin Solid Films, 1997, 295 (1/2) : 185-192.
  • 9Du H, Somers M A J, Agren J. Microstructural and compositional evolution of compound layers during gaseous nitrocarburizing [ J ]. Metall Traus A, 2000, 31(1) : 195-211.
  • 10Bell T, Sun Y, Suhadi A. Environmental and technical aspects of plasma nitrocarburising[ J]. Vac, 2000, 59(1 ) : 14-23.

引证文献6

二级引证文献23

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部