期刊文献+

脉冲馈入方式改变对束流传输的影响

Effect of pulse feed-in mode change on beam transport
在线阅读 下载PDF
导出
摘要 利用加速器原有的束流传输及检测系统,在单脉冲直线感应加速器上分别对双边馈入和单边馈入情况下强流束的传输情况进行了实验测量。实验结果表明:在改变加速脉冲的馈入方式后,传输过程中电子束在加速段的束心位置发生了明显改变,将对加速器的束流输运产生非常不利的影响。通过对实验数据的比较和分析,提出了传输线延时产生双脉冲可能采用的脉冲馈入方案。 By using the existing beam transport and detection system,experiments have been done to detect the change in the single-pulse linear induction accelerator(LIA) beam transport when the pulse symmetrical feed-in mode changes into the unilateral one.The results show that changing the pulse feed-in mode will result in a visible offset of the electron beam center in the acceleration segment.Thus the pulse unilateral feed-in mode will markedly disturb the beam transport of an LIA.According to the experiments,some feasible improvements have been advanced about the pulse feed-in mode for the double-pulse LIA based on cable delay.
出处 《强激光与粒子束》 EI CAS CSCD 北大核心 2012年第4期953-956,共4页 High Power Laser and Particle Beams
基金 国防科技基础研究基金项目
关键词 脉冲馈入方式 束流传输 直线感应加速器 传输线延时 pulse feed-in mode beam transport linear induction accelerator cable delay
  • 相关文献

参考文献7

  • 1黄子平,陈思富,邓建军,叶毅.猝发双脉冲直线感应加速器组元研究[J].强激光与粒子束,2007,19(4):695-699. 被引量:3
  • 2程念安.单组元试验台研制总结[C]//强流直线感应加速器会议文集.绵阳:中国工程物理研究院,1994:96-102.
  • 3Burns M J, Carlsten B E, Kwan T J T, et al.DARHT accelerators update and plans for initial operation[C]//Proc Part Accel Conf.1999: 617-625.
  • 4Chen Sifu, Deng Jianjun, Li Xin, et al.Design and characterization of a high-power induction module at megahertz repetition rate burst mode[J].Nuclear Instruments and Methodes in Physics Research A, 2007, 579(3): 941-950.
  • 5王华岑,文龙,章文卫,小玲,邓建军,丁伯南,陶祖聪.直线感应加速器加速腔物理设计与研究[J].强激光与粒子束,1996,8(3):313-319. 被引量:21
  • 6代志勇,章林文,邓建军,丁伯南.“神龙-I”直线感应加速器束流输运系统设计[J].强激光与粒子束,2001,13(6):781-784. 被引量:13
  • 7Fessenden T J, Stallard B W, Berg G G.Beam current and position monitor for the Astron accelerator[J].Review of Scientific Instruments, 1972, 43(12):12-16.

二级参考文献13

共引文献31

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部