期刊文献+

军用涡轴发动机发展研究 被引量:3

Development of Military Turboshaft Engine
在线阅读 下载PDF
导出
摘要 回顾了军用涡轴发动机的发展历程,介绍了几种典型军用涡轴发动机的性能特点及各国现役军用涡轴发动机的装备情况;分析并提出了军用涡轴发动机的关键技术,并通过研究国外典型涡轴发动机技术研究计划和新用的先进技术,预测了军用涡轴发动机的有关技术趋势。 The development of military turboshaft was reviewed.The performances of several typical engines and the equipment of the active service military turbo shaft engine were introduced.The key technologies of military turboshaft were analyzed and introduced.Based on the foreign typical advanced program and advanced technologies about turboshaft engine,the technology trend of military turboshaft engine was forcasted.
作者 张征
出处 《航空发动机》 2011年第6期58-62,共5页 Aeroengine
关键词 军用涡轴发动机 发展 关键技术 预测 military turboshaft engine development key technology forecast
  • 相关文献

参考文献11

二级参考文献96

  • 1倪萌,朱惠人,裘云,刘松龄.带肋壁与气膜孔内流通道中肋高度对流量系数的影响[J].燃气轮机技术,2004,17(2):30-34. 被引量:10
  • 2倪萌,朱惠人,裘云,许都纯,刘松龄.涡轮叶片内流冷却通道中压力系数的研究[J].燃气轮机技术,2004,17(4):41-47. 被引量:4
  • 3倪萌,朱惠人,裘云,许都纯,刘松龄.气膜孔与肋的相对位置及通道截面形状对气膜孔流量系数的影响[J].燃气轮机技术,2005,18(1):52-56. 被引量:7
  • 4廖明夫.涡轴发动机动力涡轮转子临界转速及不平衡响应理论分析与计算[R].株洲:中国航空动力机械研究所,2001..
  • 5邓旺群.应用于小发柔性转子的高速动平衡技术[A]..中国航空学会(动力)第三届小发动机学术讨论会论文集[C].浙江:温州,2000.92-98.
  • 6邓旺群译.应用于T700发动机的高速动平衡[R].株洲:中国航空动力机械研究所,1996..
  • 7郭飞跃.某型发动机动力涡轮转子动力特性计算报告[R].株洲:中国航空动力机械研究所,2000..
  • 8廖明夫.涡轴发动机动力涡轮转子高速动平衡技术理论分析与计算[R].株洲:中国航空动力机械研究所,2001..
  • 9邓旺群.某型发动机动力涡轮转子高速动平衡试验通用试验大纲[R].株洲:中国航空动力机械研究所,2001..
  • 10邓旺群 廖学军 力宁.平衡细长柔性转子的一种新途径[J].株洲:南华动力,2000,6(1):56-63.

共引文献147

同被引文献47

  • 1姜彩虹,孙志岩,王曦.航空发动机预测健康管理系统设计的关键技术[J].航空动力学报,2009,24(11):2589-2594. 被引量:37
  • 2尹泽勇,李上福,李概奇.无人机动力装置的现状与发展[J].航空发动机,2007,33(1):10-15. 被引量:57
  • 3孔昭健,樊未军,易琪,刘玉英,杨茂林.采用蒸发管供油的驻涡燃烧室点火及贫油熄火特性[J].航空动力学报,2007,22(7):1132-1137. 被引量:12
  • 4Hou Mingxi. Counter-rotating gearbox preliminary design and analysis for an open rotor engine[D]. UK:Cranfield University, 2010.
  • 5Dudley D W. Handbook of practical gear design [M]. United States: CRC Press LLC, 1994: 50-152.
  • 6Ma Fang. Gas turbine technology-bearing system design and analysis for a 130-seat airliner [D]. UK: Cranfield University, 2009.
  • 7Harris T A, Kotzalas M N. Rolling bearing analysis essential concepts of bearing technology[M]. Fifth edition. United States: Taylor & Francis Group, 2007 : 45-72.
  • 8British Standards Institution. ISO 6336-1: Calculation of load capacity of spur and helical gears-Part 1: Basic principles, in- troduction and general influence factors [S]. Britain: British Standards Institution, 2006:12-75.
  • 9British Standards Institution. ISO 6336-2: Calculation of load capacity of spur and helical gears-Part 2: Calculation of sur- face durability (pitting)[S]. Britain: British Standards Institu- tion, 2006:3-29.
  • 10British Standards Institution. ISO 6336-3: Calculation of load capacity of spur and helical gears-Part 3: Calculation of tooth bending strength [S]. Britain: British Standards Institution, 2006:1-32.

引证文献3

二级引证文献19

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部