期刊文献+

在并/逆流喷雾蒸发器中浓缩净化磷酸的研究 被引量:1

Study on concentration and purification of phosphoric acid in co/counter-current evaporator
在线阅读 下载PDF
导出
摘要 为获得较高浓度磷酸以满足对磷酸使用和运输的要求,采用正交实验和单因素实验对净化稀磷酸进行了喷雾蒸发浓缩的系统实验研究。实验结果发现:影响净化稀磷酸蒸发浓缩效果的因素由主到次依次为稀磷酸流量、热风进口流量、二次风比例、热风进口温度、喷嘴气液比;浓缩的效果正比于热风进口流量、热风进口温度、稀磷酸流量的倒数,且在喷嘴气液质量比大于0.8时受其影响不大;二次风的引入对稀磷酸浓缩不利。在实验装置上经喷雾浓缩,成功获得了质量分数不低于85%的浓磷酸,并发现相应的热风出口温度不宜低于110℃。由此可见,通过喷雾蒸发浓缩得到较高浓度的磷酸是可行的。 Systematically experimental study on spray evaporation to concentrate purified phosphoric acid has been carried out by orthogonal and single factor experiments in order to attain highly concentrated phosphoric acid to achieve the quality requirement of utilization and transport of it. Results showed that the factors influencing evaporation concentration efficiency of dilute purified phosphoric acid, according to the importance of which, were dilute phosphoric acid flow rate,inlet heated air flow rate, ratio of secondary air, inlet heated air temperature, and gas to liquid ratio at atomizer;efficiency of concentration,which was weakly related to gas to liquid ratio at atomizer when it is more than 0.8,was proportional to inlet heated air flow rate,inlet heated air lemperature, and reciprocal of dilute phosphoric acid flow rate;induced secondary air did not facilitate concentration. Besides, concentrated phosphoric acid that was up to 85% in mass fraction of H3PO4 has been obtained in experiment and it was also found that the temperature of relevant outlet gas should not be less than 110 ℃. So it is feasible to concentrate purified phosphoric acid to get comparatively high concentration by spray evaporation.
出处 《无机盐工业》 CAS 北大核心 2010年第2期36-39,共4页 Inorganic Chemicals Industry
基金 国家科技支撑计划课题<高纯磷化工产品关键设备开发>资助项目(2007BAE58B02)
关键词 磷酸 喷雾蒸发 喷嘴气液比 phosphoric acid spray evaporation gas-liquid ratio at atomizer
  • 相关文献

参考文献6

二级参考文献17

  • 1周绍彪.湿法磷酸生产中常用的合金材料[J].磷肥与复肥,2005,20(2):63-66. 被引量:5
  • 2段付岗,王少婷.提高磷石膏洗涤率的措施[J].磷肥与复肥,1996,11(3):34-38. 被引量:12
  • 3C T rowe, et al. The particle - source - in - cell ( PSI - Cell) model for gas - droplet flows[J], J. Fluid Eng, 1997, (9) :325 -332.
  • 4C T Crowe. Modeling Spray - air Contact in spray Drying Systems [ C ]. Advances in Drying. 1980, ( 1 ) :63 - 99.
  • 5S E Papadakis and J King. Air temperature and humidity profiles in spray drying[ R]. Features predicted by the particle source in cell model. Ind,Eng. Chem. Res. ,1988, (27) :116 -2123.
  • 6R Rotondi, G Bella. Gasoline direct injection spray simulation [J]. International Joumal of Thermal Sciences, 2006, (45) : 168 - 179.
  • 7L X Huang, et al. A comparative study of a spray dryer with rotary disc atomizer and pressure nozzle using computational fluid dynamic simulations [ J ]. Chemincal Engineering and Processing, 2006 (45) :461 -470.
  • 8D Brandley. On the atomization of Liquids by High - Velocity Gases [ J ]. Journal of Physics D, 1973, (6) : 1724 - 2272.
  • 9F G Kieviet, P J A M Kerkhof. Using Computational Fluid Dynamics to Model Product Quantity in spray Drying: Air Flow Temperature and Humidity Patterns[ C]. Drying'96. 1996, A:259 -266.
  • 10F G Kieviet. Modeling Quality in spray Drying, Ph. D. thesis[ D]. Endinhoven University of Technology, the Netherlands, 1997.

共引文献34

同被引文献1

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部