期刊文献+

高速数据采集系统设计 被引量:16

Design of High Speed Data Acquisition System
在线阅读 下载PDF
导出
摘要 为满足雷达信号采集的要求,设计一个12 bit 100 MS/s的基于PCI总线的数据采集系统。该系统能够实现6GB数据的实时采集与存储。可编程逻辑器件控制数据的采集、存储与传输。PCI数据传输采用PCI主模式,传输速率达到60MB/s,采集信号的信噪比达到55dB(30MHz模拟信号)。 A 100 MS/s data acquisition system based on PCI bus is designed to meet the need of high-speed radar signal sampling. The 6 GB sampling ADC data can be saved on this card and transferred to the computer simultaneously, which is controlled by one FPGA chip. The transfer rate between this card and the computer can reach up 60 MB/s. The SNR of the sampled data can reach 55 dB at 30 MHz.
出处 《计算机工程》 CAS CSCD 北大核心 2009年第1期207-209,212,共4页 Computer Engineering
基金 国家自然科学基金资助项目"基于骨骼肌结构形态信息的假手控制与建模研究"(60701021) 上海市优秀青年教师基金资助项目(2005) 上海市重点学科建设基金资助项目(T0102)
关键词 PCI控制器 可编程器件 抖动 信噪比 PCI controller FPGA jitter SNR
  • 相关文献

参考文献5

二级参考文献23

  • 1张蕴玉,宋宇明,胡修林,张华.多通道高速数据采集系统PCI接口的结构设计[J].华中科技大学学报(自然科学版),2004,32(8):73-75. 被引量:7
  • 2张武,张春华,唐劲松,杜立君.基于PC/104-Plus总线数据采集系统设计与实现[J].微计算机应用,2006,27(1):55-58. 被引量:9
  • 3郭志平,董宇峰,张朝宗.工业CT技术[J].无损检测,1996,18(1):27-30. 被引量:50
  • 4Chris Cant.Windows WDM设备驱动程序开发指南[M].北京:机械工业出版社,2000..
  • 5Da Dalt N,Harteneck M,et a1.On the jitter requirements of the sampling clock for aim—og-to-digiital converters[J].IEEE Transactions On Circuits and Systems I:Fundamental Theory and Applications,2002,49(9):1 354—1 360.
  • 6John G Proakis.Digital Communications,4th ed [M].北京:电子工业出版社,2003,62—66.
  • 7Hajhniri A,Limotyrakis S,Lee T H.Jitter and phase noise in dng oscillators[J].IEEE J Solid-state Circuits,1999,34(6):790-804.
  • 8Razavi B.A study of phase noise in CMOS oscillators[J].IEEE J Solid Circuits,1996,31(3):331-343.
  • 9Shinagawa M Akazawa,et a1.Jitter analysis of high-speed sampling systerns[J].IEEE J Solid-state Circuits,1990,25(1):220-224.
  • 10OpenCores.WISHBONE System-on-Chip(SoC).Interconnection Architecture for Portable IP Cores(Revision B.3)[Z].2002-09-07.

共引文献14

同被引文献97

引证文献16

二级引证文献78

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部