期刊文献+

聚乙烯醇水凝胶/不锈钢摩擦性能研究 被引量:1

Friction properties of PVA hydrogel against stainless steel ball
在线阅读 下载PDF
导出
摘要 利用球-盘摩擦试验机研究润滑状态、载荷、滑动速度和不锈钢球直径对PVA水凝胶/不锈钢球摩擦副摩擦系数的影响。研究结果表明PVA凝胶内的自由水对摩擦副起着良好的润滑作用。在摩擦的起始阶段,干摩擦和润滑剂润滑状态下的摩擦系数相差甚微,随摩擦时间的延长,干摩擦状态下的摩擦系数在短时间内急剧上升,而润滑剂润滑状态下的摩擦系数基本保持不变;摩擦副的摩擦系数随滑动速度和不锈钢球直径的增加而下降,当滑动速度从45r/min升至225r/min时,摩擦副的摩擦系数下降54.24%;摩擦系数随载荷的增加而上升,但在低载荷区,摩擦副的摩擦系数的上升速率明显大于其在高载荷区的上升速率。随着载荷的增加,凝胶中自由水对摩擦副的润滑作用逐渐增强。 The effects of different variable factors on the friction coefficient of poly(vinyl alcohol) (PVA) hydrogel and stainless steel ball counterpart were investigated by ball-pan friction and wear tester. Factors included lubrication condition, sliding speed, diameter of stainless steel ball, and load. It is shown that the free water in PVA hydrogel has a good lubrication on the friction counterpart. The friction coefficients have little difference between dry and lubricants lubrication condition at initial friction test. With the friction test time prolonged, friction coefficient of PVA hydrogel under dry condition increased sharply at short time. Friction coefficient decreased with the increasing sliding speed and diameter of stainless steel ball. It reduced 54.24% ,while the slid- ing speed enhancing from 45r/min to 225r/min. It increased with an increase in load. The rising rate of friction coefficient at low load region is obviously larger than that at high load region. The effect of free water in PVA hydrogel on the friction coefficient gradually enhanced with the increasing load.
出处 《功能材料》 EI CAS CSCD 北大核心 2006年第12期1974-1977,共4页 Journal of Functional Materials
基金 国家自然科学基金资助项目(50575106)
关键词 聚乙烯醇水凝胶 不锈钢球 摩擦系数 poly(vlnyl alcohol) hydrogel stainless steel ball friction coefficient
  • 相关文献

参考文献17

二级参考文献19

  • 1Wang A,Tribol Int,1998年,31卷,1/3期,17页
  • 2Yin G F,Thin Solid Film,1999年,345卷,67页
  • 3McGee M A, Howie D W, Neale S D, et al. The role of polyethylene wears in joint replacement failure[J]. Proc Instn Mech Engr Part H, 1997, 211: 65-72.
  • 4Weightmsn B, light D. The effect of the surface finish of alumina and stainless steel on the wear rate of UHMWPE polyethylene[J]. Biomaterials, 1986,17: 20-24.
  • 5Dowson D. A comparative study of the performance of metallic and ceramic femoral heat components in total replacement hip joints[J]. Wear, 1995,190: 171-183.
  • 6Xiong D S, Ge S R. Friction and wear properties of UHMWPE/Al2O3 ceramic under different lubricating condition [J]. Wear, 2001, 251:1 094-1 099.
  • 7Dong H, Shi W, Bell T. Potential of improving tribological performance of UHMWPE by engineering the Ti6Al4V counterfaces[J]. Wear, 1999, 225-229: 146-153.
  • 8Rao G R, Lee E H, Bhattacharya R, et al. Improved wear properties of high energy ion-implanted polycarbonate[J]. J Mater Res, 1995, 10 (1): 190-201.
  • 9Lee Y, Lee E H, Mansur L K. Hardness and wear properties of boron-implanted poly (ether-ether-ketone) and polyetherimide [J]. Surface and Coatings Technology, 1992, 51: 267-272.
  • 10Han S H,Lee Y H,Kim H D,et al.Polymer surface modification by plasma source ion implantation[J].Surface and Coatings Technology,1997,93:261-264.

共引文献79

同被引文献39

  • 1王砚军,刘佐民.微孔贯通型高温自润滑金属陶瓷的摩擦磨损性能研究[J].摩擦学学报,2006,26(4):348-352. 被引量:13
  • 2闫普选,王晓东,朱鹏,谷和平,黄培.热塑性聚酰亚胺多孔材料制备及表征[J].轴承,2006(8):19-22. 被引量:10
  • 3潘育松,熊党生,马如银.聚乙烯醇水凝胶/钛合金摩擦磨损特性的正交试验研究[J].摩擦学学报,2007,27(2):132-136. 被引量:5
  • 4Ananthanarayan V T, Shutov F. Development of fabric sintering/compaction process to produce porous UHMW Polyethylene composites[J]. J Biomaterials Appl, 2001,16 : 139.
  • 5Shutov F, Ananthanarayan V T. Cellular UHMW polyethylene produced by non-foaming leaching technique: Morphology and properties[J]. J Cellular Plastic, 2002,28 : 163.
  • 6Zhou X C, Fisher J. The influence of concave dimples on the metallic counterface on the wear of UHMWPE [C]//The 3^rd Conference of BiO-tribdogy. Chengdu, 2005:7.
  • 7Vivanco Juan, Fang Sam, Levine Danny. Microstructural mechanical fe analysis of direct compression molded porous tantalum-UHMWPE[C]// 16th ESB Congress, Poster P- 71,S444.
  • 8Kevin Plumlee, Christian J Schwartz. Improved wear resistance of orthopaedic UHMWPE by reinforcement with zirconium particles[J]. Wear, 2009,267 :710.
  • 9Jayashree Bijwe, Rekha Rattan. Influence of weave of carbon fabric in polyetherimide composites in various wear situations[J]. Wear, 2007,263:984.
  • 10Zhu Heguo, Wang Hengzhi, et al. Wear properties of the composites fabricated by exothermic dispersion reaction synthesis in an Al-TiO2-B2O3 system[J]. Wear, 2008,264 : 967.

引证文献1

二级引证文献4

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部