The yield strength of commercially pure(CP) Ti of ASTM grade 4, the strongest among all the CP-Ti grades, is too low for structural applications that require high-strength materials. Here, we demonstrate the strengthe...The yield strength of commercially pure(CP) Ti of ASTM grade 4, the strongest among all the CP-Ti grades, is too low for structural applications that require high-strength materials. Here, we demonstrate the strengthening of grade-4 CP Ti by cryogenic-temperature rolling(CTR), which enables deformation twinning in grade-4 CP Ti to achieve twinning-induced grain refinement. CTR activated {11.22} twinning and {10.12} twinning, which are the most common twinning systems in pure Ti, whereas room-temperature rolling(RTR) did not activate any twinning system. CTR with imposing an area reduction of just 30% significantly increased the yield strength of the CP Ti to 946 MPa, which is not achievable through typical processes performed at or above room temperature and is comparable to that of commercial Ti-6 Al-4 V. The significant increase in strength was due to microstructural strengthening caused by twinning-induced grain refinement, combined with dislocation accumulation. In contrast to RTR, CTR greatly increased the stress concentration at grain boundaries(GBs), which caused the unusual activation of twinning in the grade-4 CP Ti by facilitating twin nucleation at GBs. The stress concentration increased because CTR activated the slip to a lesser extent compared to RTR, thereby reducing the strain compatibility between neighboring grains. These results will contribute to development of ultrahigh-strength CP Ti and may thereby extend its use to structural applications that require high-strength materials.展开更多
The demand for titanium alloys simultaneously having high elastic admissible strain and large recovery strain for bio-implant applications is increasing.Ni-free Ti-based shape memory alloys are promising candidates fo...The demand for titanium alloys simultaneously having high elastic admissible strain and large recovery strain for bio-implant applications is increasing.Ni-free Ti-based shape memory alloys are promising candidates for obtaining the required multifunctional properties.In this study,a wide content range of(0-15)wt%of low-cost,toxicity-free,and high-biocompatible Sn element was added to the Ti-8Mo(wt%)alloy to study its effect on the superelastic recovery and mechanical properties of biomedical Ti-Mo-Sn alloys.By tailoring Sn content,desired multifunctional properties of high elastic admissible strain and room temperature superelasticity were achieved in the studied Ti-Mo-Sn alloys.It was found that the increase in Sn content stabilized theβphase and a singleβphase was obtained at room temperature in Ti-8Mo-(13,15)Sn alloys.The addition of Sn modified the lattice parameters of theα″martensite andβphase and affected the lattice deformation stain ofβ→α″.The lattice deformation strain along the[011]βdirection was found to be decreased by-0.26%/wt%Sn.The room temperature superelasticity with a recovery strain of 3.1%and an elastic admissible strain of 1%was obtained in the Ti-8Mo-13Sn alloy.As Sn content increased to 15 wt%,a high elastic admissible strain of 1.56%and a recovery strain of 2.0%were obtained.These Ti-Mo-Sn alloys with excellent multifunctional properties are promising candidates for bio-implant applications.展开更多
Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powd...Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.展开更多
Oxidation study of Fe-36Ni and Fe-46Ni alloys was conducted on the effect of temperature under a 0.2 atm oxygen partial pressure. The weight of both specimens was continuously measured by TGA （thermogravimetric appar...Oxidation study of Fe-36Ni and Fe-46Ni alloys was conducted on the effect of temperature under a 0.2 atm oxygen partial pressure. The weight of both specimens was continuously measured by TGA （thermogravimetric apparatus） at various temperatures and it was found that the weigh was gained with an increase of temperature. The oxidation behavior of Fe-36/46Ni alloys was found to be followed by parabolic rate law and the rate constants were linearly proportional to the temperature. In addition, activation energies of Fe-36Ni and Fe-46Ni alloys were calculated to be 106.49 kJ/mol and 58.99 kJ/mol, respectively. The cross sectional area of oxide scale was examined by SEM （scanning electron microscopy） and analyzed by XRD （X-ray diffraction） and EDX （energy-dispersive X-ray spectroscopy）.展开更多
基金supported by the Civil-Military Technology Cooperation Program funded by the Ministry of Trade Industry and Energy, Republic of Korea (16-CM-MA-10)。
文摘The yield strength of commercially pure(CP) Ti of ASTM grade 4, the strongest among all the CP-Ti grades, is too low for structural applications that require high-strength materials. Here, we demonstrate the strengthening of grade-4 CP Ti by cryogenic-temperature rolling(CTR), which enables deformation twinning in grade-4 CP Ti to achieve twinning-induced grain refinement. CTR activated {11.22} twinning and {10.12} twinning, which are the most common twinning systems in pure Ti, whereas room-temperature rolling(RTR) did not activate any twinning system. CTR with imposing an area reduction of just 30% significantly increased the yield strength of the CP Ti to 946 MPa, which is not achievable through typical processes performed at or above room temperature and is comparable to that of commercial Ti-6 Al-4 V. The significant increase in strength was due to microstructural strengthening caused by twinning-induced grain refinement, combined with dislocation accumulation. In contrast to RTR, CTR greatly increased the stress concentration at grain boundaries(GBs), which caused the unusual activation of twinning in the grade-4 CP Ti by facilitating twin nucleation at GBs. The stress concentration increased because CTR activated the slip to a lesser extent compared to RTR, thereby reducing the strain compatibility between neighboring grains. These results will contribute to development of ultrahigh-strength CP Ti and may thereby extend its use to structural applications that require high-strength materials.
基金the Korean Ministry of Trade,Industry and Energy(Grant No.200116572).
文摘The demand for titanium alloys simultaneously having high elastic admissible strain and large recovery strain for bio-implant applications is increasing.Ni-free Ti-based shape memory alloys are promising candidates for obtaining the required multifunctional properties.In this study,a wide content range of(0-15)wt%of low-cost,toxicity-free,and high-biocompatible Sn element was added to the Ti-8Mo(wt%)alloy to study its effect on the superelastic recovery and mechanical properties of biomedical Ti-Mo-Sn alloys.By tailoring Sn content,desired multifunctional properties of high elastic admissible strain and room temperature superelasticity were achieved in the studied Ti-Mo-Sn alloys.It was found that the increase in Sn content stabilized theβphase and a singleβphase was obtained at room temperature in Ti-8Mo-(13,15)Sn alloys.The addition of Sn modified the lattice parameters of theα″martensite andβphase and affected the lattice deformation stain ofβ→α″.The lattice deformation strain along the[011]βdirection was found to be decreased by-0.26%/wt%Sn.The room temperature superelasticity with a recovery strain of 3.1%and an elastic admissible strain of 1%was obtained in the Ti-8Mo-13Sn alloy.As Sn content increased to 15 wt%,a high elastic admissible strain of 1.56%and a recovery strain of 2.0%were obtained.These Ti-Mo-Sn alloys with excellent multifunctional properties are promising candidates for bio-implant applications.
基金Project(K0004130) supported by the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy,Korea
文摘Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.
文摘Oxidation study of Fe-36Ni and Fe-46Ni alloys was conducted on the effect of temperature under a 0.2 atm oxygen partial pressure. The weight of both specimens was continuously measured by TGA （thermogravimetric apparatus） at various temperatures and it was found that the weigh was gained with an increase of temperature. The oxidation behavior of Fe-36/46Ni alloys was found to be followed by parabolic rate law and the rate constants were linearly proportional to the temperature. In addition, activation energies of Fe-36Ni and Fe-46Ni alloys were calculated to be 106.49 kJ/mol and 58.99 kJ/mol, respectively. The cross sectional area of oxide scale was examined by SEM （scanning electron microscopy） and analyzed by XRD （X-ray diffraction） and EDX （energy-dispersive X-ray spectroscopy）.
