The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The ...The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The process of precipitation of the secondary phase can be accelerated with cold deformation before aging, so properties of the alloy are improved. Upon aging at 500°C for 30 minutes after 60% cold deformation, the values of electrical conductivity and microhardness are 69.0%IACS and 152HV respectively, but they are only 66.2%IACS and 136HV upon directly aging after solution. With the addition of a trace of rare earth element Ce, the value of microhardness of Cu-0.35Cr-0.038Zr alloy increases 18-25HV, while the value of electrical conductivity drops a little.展开更多
A simpler and more convenient method for producing wear-resistant, TiC-reinforced coatings were investigated in this study. It consists of the simultaneous synthesis and deposition of TiC-Fe materials by oxyacetylene ...A simpler and more convenient method for producing wear-resistant, TiC-reinforced coatings were investigated in this study. It consists of the simultaneous synthesis and deposition of TiC-Fe materials by oxyacetylene flame spraying. Solid reagents bound together to form a single particle are injected into the flame stream where an in-situ reaction occurs. The reaction products are propelled onto a substrate to form a coating. Microstructural analyses reveal that TiC and Fe are the dominant phases in the coatings. The reaction between Ti and C happens step by step along with the reactive spray powder flight, and TiC-Fe materials were mainly synthesized where the spray distance is 125-170 mm. The TiC-Fe coatings are composed of alternate TiC-rich and TiC-poor lamellae with different microhardness of 11.9-13.7 and 3.0-6.0 GPa, respectively. Submicron and round TiC particles are dispersed within a ductile metal matrix. The peculiar microstructure is thought to be responsible for its good wear resistance, which is better nearly five times than WC-reinforced cermet coatings obtained by traditional oxyacetylene flame spray.展开更多
The improvement of machining behavior of prehardened-mould steel for plastic is realized by using computer-aided composition design in this work. The results showed that the matrix composition of large sectional preha...The improvement of machining behavior of prehardened-mould steel for plastic is realized by using computer-aided composition design in this work. The results showed that the matrix composition of large sectional prehardened mould steel for plastic markedly influences the precipitation of non-metallic inclusion and the control of composition aided by Thermo-Calc software package minimizes the amount of detrimental oxide inclusion. In addition the modification of calcium is optimized in the light of composition design.展开更多
A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning...A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning electron microscopy, transmission electron microscopy, dilatometry and tensometry. Those measurements suggested that the steel consisted of martensite and retained austenite, which existed between the martensitic laths in a stable thin film, and that the steel showed very high tensile strength of 1400 MPa and good ductility of 15% in elongation after 300°C tempering.展开更多
According to ASTM Designation DXXXX Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit), a test unit was designed using which the coo...According to ASTM Designation DXXXX Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit), a test unit was designed using which the cooling characteristics of a quenchant at different flow rates and different temperatures can be determined. We discussed the effects of flow rate and temperature on cooling characteristics of fast speed quenching oil. The results show that this unit can be well used for determining cooling characteristics of quechants at different flow rates and different temperatures. At the same time our investigation can provide a reference to the establishment of a standard for determination of cooling characteristics of quenchants with agitation.展开更多
Sintering additives to gelcasting Sialon-SiC were decided by the optimizing experiments. The results show that Sialon-SiC can be sintered under 1450℃ and sintering temperature decreases by 100℃, when 2%～3% TiO 2 o...Sintering additives to gelcasting Sialon-SiC were decided by the optimizing experiments. The results show that Sialon-SiC can be sintered under 1450℃ and sintering temperature decreases by 100℃, when 2%～3% TiO 2 or Guangxi clay is used as sintering additive.展开更多
According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15&#...According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15°(+15°) should be adopted, which will benefit the floatation of non-metallic inclusion and purification of the molten steel. When the nozzle angle is 120°, the flow pattern is reasonable. Proper nozzle depth can be 200mm. Turbulent kinetic of meniscus can be reduced by adopting the square nozzle and suitable area of side outlet when casting speed increases. The results are consistent with those of water model experiment, so the model is exact and reasonable. The model can provide important information for design of SEN and defining of immersion depth.展开更多
Four 2-(α-hydroxyalkyl)-2-oxazolines and a 2-(α-hydroxy-α,α-diphenyl)-2-benzooxazole were synthesized from β-amimoalcohols and α-hydroxy carboxylic acids under microwave irradiation in the absence of a solvent.
Ni-Fe-C filler metal based on WC-30Co/Ni-Fe-C/45 steel is developed using TIGwelding method. The weld joints are studied by means of optical microscope, SEM, EPMA, X-rays andmicro hardness test etc. The results show t...Ni-Fe-C filler metal based on WC-30Co/Ni-Fe-C/45 steel is developed using TIGwelding method. The weld joints are studied by means of optical microscope, SEM, EPMA, X-rays andmicro hardness test etc. The results show that the weld joints of WC-30Co and 45 steel can beobtained by TIG welding using Ni-Fe-C alloys as filler metals. The harmful eta phase formed in thejoints is M_6C, M_(12)C type carbides. The poor carbon content of the W-Co-C system resulted fromthe carbon diffusion and the high ingredient Fe are the two vital factors inducing to eta phaseformation. It could be restricted by the addition of carbon element into Ni-Fe alloys.展开更多
With the finite element analysis of viscous quenchant flow fields of the ASTM assembly, the effective average velocities of flow tubes are introduced in this paper. And through the results of experiments, the influenc...With the finite element analysis of viscous quenchant flow fields of the ASTM assembly, the effective average velocities of flow tubes are introduced in this paper. And through the results of experiments, the influences of quenchant velocities upon the whole cooling processes are discussed.展开更多
基金supported by the National 863 Plan Items of China(No.2002AA331112)
文摘The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The process of precipitation of the secondary phase can be accelerated with cold deformation before aging, so properties of the alloy are improved. Upon aging at 500°C for 30 minutes after 60% cold deformation, the values of electrical conductivity and microhardness are 69.0%IACS and 152HV respectively, but they are only 66.2%IACS and 136HV upon directly aging after solution. With the addition of a trace of rare earth element Ce, the value of microhardness of Cu-0.35Cr-0.038Zr alloy increases 18-25HV, while the value of electrical conductivity drops a little.
基金This work was supported by the National "863" Project of China under grant No. 715-009-0130.
文摘A simpler and more convenient method for producing wear-resistant, TiC-reinforced coatings were investigated in this study. It consists of the simultaneous synthesis and deposition of TiC-Fe materials by oxyacetylene flame spraying. Solid reagents bound together to form a single particle are injected into the flame stream where an in-situ reaction occurs. The reaction products are propelled onto a substrate to form a coating. Microstructural analyses reveal that TiC and Fe are the dominant phases in the coatings. The reaction between Ti and C happens step by step along with the reactive spray powder flight, and TiC-Fe materials were mainly synthesized where the spray distance is 125-170 mm. The TiC-Fe coatings are composed of alternate TiC-rich and TiC-poor lamellae with different microhardness of 11.9-13.7 and 3.0-6.0 GPa, respectively. Submicron and round TiC particles are dispersed within a ductile metal matrix. The peculiar microstructure is thought to be responsible for its good wear resistance, which is better nearly five times than WC-reinforced cermet coatings obtained by traditional oxyacetylene flame spray.
文摘The improvement of machining behavior of prehardened-mould steel for plastic is realized by using computer-aided composition design in this work. The results showed that the matrix composition of large sectional prehardened mould steel for plastic markedly influences the precipitation of non-metallic inclusion and the control of composition aided by Thermo-Calc software package minimizes the amount of detrimental oxide inclusion. In addition the modification of calcium is optimized in the light of composition design.
文摘A martensitic microalloyed steel, 25Si2MnCrMo, was developed to meet the demands of the high-strength bars. Microstructure and mechanical properties of the steel were evaluated by using optical metallography, scanning electron microscopy, transmission electron microscopy, dilatometry and tensometry. Those measurements suggested that the steel consisted of martensite and retained austenite, which existed between the martensitic laths in a stable thin film, and that the steel showed very high tensile strength of 1400 MPa and good ductility of 15% in elongation after 300°C tempering.
基金This paper funded by"The Key Science and TechnologyResearch Project of The Ministry of Education,No.03067"Corresponding
文摘According to ASTM Designation DXXXX Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit), a test unit was designed using which the cooling characteristics of a quenchant at different flow rates and different temperatures can be determined. We discussed the effects of flow rate and temperature on cooling characteristics of fast speed quenching oil. The results show that this unit can be well used for determining cooling characteristics of quechants at different flow rates and different temperatures. At the same time our investigation can provide a reference to the establishment of a standard for determination of cooling characteristics of quenchants with agitation.
文摘Sintering additives to gelcasting Sialon-SiC were decided by the optimizing experiments. The results show that Sialon-SiC can be sintered under 1450℃ and sintering temperature decreases by 100℃, when 2%～3% TiO 2 or Guangxi clay is used as sintering additive.
文摘According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15°(+15°) should be adopted, which will benefit the floatation of non-metallic inclusion and purification of the molten steel. When the nozzle angle is 120°, the flow pattern is reasonable. Proper nozzle depth can be 200mm. Turbulent kinetic of meniscus can be reduced by adopting the square nozzle and suitable area of side outlet when casting speed increases. The results are consistent with those of water model experiment, so the model is exact and reasonable. The model can provide important information for design of SEN and defining of immersion depth.
文摘Four 2-(α-hydroxyalkyl)-2-oxazolines and a 2-(α-hydroxy-α,α-diphenyl)-2-benzooxazole were synthesized from β-amimoalcohols and α-hydroxy carboxylic acids under microwave irradiation in the absence of a solvent.
文摘Ni-Fe-C filler metal based on WC-30Co/Ni-Fe-C/45 steel is developed using TIGwelding method. The weld joints are studied by means of optical microscope, SEM, EPMA, X-rays andmicro hardness test etc. The results show that the weld joints of WC-30Co and 45 steel can beobtained by TIG welding using Ni-Fe-C alloys as filler metals. The harmful eta phase formed in thejoints is M_6C, M_(12)C type carbides. The poor carbon content of the W-Co-C system resulted fromthe carbon diffusion and the high ingredient Fe are the two vital factors inducing to eta phaseformation. It could be restricted by the addition of carbon element into Ni-Fe alloys.
基金This paper funded bu "The key science and Technology Research Project of The Ministry of Education .No.03067"
文摘With the finite element analysis of viscous quenchant flow fields of the ASTM assembly, the effective average velocities of flow tubes are introduced in this paper. And through the results of experiments, the influences of quenchant velocities upon the whole cooling processes are discussed.
