Aluminum based metal matrix composites were fabricated using stir casting where silicon carbide and alumina were the reinforcements. Different types of properties (physical-density, mechanical-tensile, hardness, chemi...Aluminum based metal matrix composites were fabricated using stir casting where silicon carbide and alumina were the reinforcements. Different types of properties (physical-density, mechanical-tensile, hardness, chemical-corrosion etc.) were measured and compared with base metals/alloys. The properties were significantly varied. The highest density was obtained for pure aluminium with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for AA-4032 alloy. The highest hardness was obtained for AA-4032 with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for pure Al with 5% Al<sub>2</sub>O<sub>3</sub>. The highest strength was obtained for AA-6061 with 5% coarse SiC whereas the lowest was obtained for pure Al. The highest impact strength was obtained for AA-4032 with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for AA-6061. The corrosion resistance of all composites was lower than that of the base materials.展开更多
Zirconia toughened alumina (ZTA) ceramics are very promising materials for structural and biomedical applications due to their high hardness, fracture toughness, strength, corrosion and abrasion resistance and excelle...Zirconia toughened alumina (ZTA) ceramics are very promising materials for structural and biomedical applications due to their high hardness, fracture toughness, strength, corrosion and abrasion resistance and excellent biocompatibility. The effect of unstabilized ZrO<sub>2</sub> on the density, fracture toughness, microhardness, flexural strength and microstructure of some Zirconia-toughened alumina (ZTA) samples was investigated in this work. The volume percentage of unstabilized ZrO<sub>2</sub> was varied from 0% - 20% whereas sintering time and sintering temperature were kept constant at 2 hours and 1580°C. The samples were fabricated from nanometer-sized (<em>α</em>-Al<sub>2</sub>O<sub>3</sub>: 150 nm, monoclinic ZrO<sub>2</sub>: 30 - 60 nm) powder raw materials by the conventional mechanical mixing process. Using a small amount of sintering aid (0.2 wt% MgO) almost 99.2% of theoretical density, 8.54 MPam<sup>?</sup> fracture toughness, 17.35 GPa Vickers microhardness and 495.67 MPa flexural strength were found. It was observed that the maximum flexural strength and fracture toughness was obtained for 10 vol% monoclinic ZrO<sub>2</sub> but maximum Vickers microhardness was achieved for 5 vol% ZrO<sub>2</sub> although the maximum density was found for 20 vol% ZrO<sub>2</sub>. It is assumed that this was happened due to addition of denser component, phase transformation of monoclinic ZrO<sub>2</sub> and the changes of grain size of α-Al<sub>2</sub>O<sub>3</sub> and ZrO<sub>2</sub>.展开更多
Extrusion-Compression molded isotactic polypropylene (iPP) composites containing 10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt% of talc filler were studied by scanning electron microscopy (SEM), simultaneous thermal analys...Extrusion-Compression molded isotactic polypropylene (iPP) composites containing 10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt% of talc filler were studied by scanning electron microscopy (SEM), simultaneous thermal analysis (STA) and physical testing. The scanning electron microscope (SEM) micrographs of neat iPP and composites with 10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt% talc content show that neat PP, 10 wt%, 20 wt%, and 30wt% talc composites surface is smooth in comparison to 40 wt% and 50 wt% talc composites. It is also observed that talc is dispersed uniformly in the matrix and this uniform dispersion is not decreased even with talc content as high as 30 wt% talc. The composites of 40 wt% and 50 wt% talc contain more crack, agglomerates or larger particles. Bulk density of the composites decreases with the increase of talc content. With the increase of percentage of talc and period of immersion, the water absorption (WA) increases. Thermal analyses indicate a considerable increase of thermal stability of the composites with filler addition.展开更多
In this research work, (Bi<sub>2</sub>O<sub>3</sub>Fe<sub>2</sub>O<sub>3</sub>)<sub>0.4</sub>(Nb<sub>2</sub>O<sub>5</sub>)<sub>...In this research work, (Bi<sub>2</sub>O<sub>3</sub>Fe<sub>2</sub>O<sub>3</sub>)<sub>0.4</sub>(Nb<sub>2</sub>O<sub>5</sub>)<sub>0.6</sub> was made by the solid state reaction method. Samples were sintered at four different temperatures (850°C, 925°C, 1000°C and 1150°C) to study the effect of sintering temperature on the various properties of the samples. X-ray diffraction analysis confirmed that single phase Bi<sub>1.721</sub>δ<sub>0.089</sub>Fe<sub>1.056</sub>Nb<sub>1.134</sub>O<sub>7</sub> was found when sintering temperature increased. At the same time, larger grain size was found when sintering temperature increased. From variation of dielectric loss with respect to frequency, a small peak was found when sample was sintered at higher temperature (1150°C). Dielectric constant of the sample decreases with the increase of frequency for all the samples. With the variation of temperature, DC resistivity of the samples showed that resistivity decreases with the increase of measuring temperature which indicates semiconducting nature.展开更多
文摘Aluminum based metal matrix composites were fabricated using stir casting where silicon carbide and alumina were the reinforcements. Different types of properties (physical-density, mechanical-tensile, hardness, chemical-corrosion etc.) were measured and compared with base metals/alloys. The properties were significantly varied. The highest density was obtained for pure aluminium with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for AA-4032 alloy. The highest hardness was obtained for AA-4032 with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for pure Al with 5% Al<sub>2</sub>O<sub>3</sub>. The highest strength was obtained for AA-6061 with 5% coarse SiC whereas the lowest was obtained for pure Al. The highest impact strength was obtained for AA-4032 with 5% Al<sub>2</sub>O<sub>3</sub> whereas the lowest was obtained for AA-6061. The corrosion resistance of all composites was lower than that of the base materials.
文摘Zirconia toughened alumina (ZTA) ceramics are very promising materials for structural and biomedical applications due to their high hardness, fracture toughness, strength, corrosion and abrasion resistance and excellent biocompatibility. The effect of unstabilized ZrO<sub>2</sub> on the density, fracture toughness, microhardness, flexural strength and microstructure of some Zirconia-toughened alumina (ZTA) samples was investigated in this work. The volume percentage of unstabilized ZrO<sub>2</sub> was varied from 0% - 20% whereas sintering time and sintering temperature were kept constant at 2 hours and 1580°C. The samples were fabricated from nanometer-sized (<em>α</em>-Al<sub>2</sub>O<sub>3</sub>: 150 nm, monoclinic ZrO<sub>2</sub>: 30 - 60 nm) powder raw materials by the conventional mechanical mixing process. Using a small amount of sintering aid (0.2 wt% MgO) almost 99.2% of theoretical density, 8.54 MPam<sup>?</sup> fracture toughness, 17.35 GPa Vickers microhardness and 495.67 MPa flexural strength were found. It was observed that the maximum flexural strength and fracture toughness was obtained for 10 vol% monoclinic ZrO<sub>2</sub> but maximum Vickers microhardness was achieved for 5 vol% ZrO<sub>2</sub> although the maximum density was found for 20 vol% ZrO<sub>2</sub>. It is assumed that this was happened due to addition of denser component, phase transformation of monoclinic ZrO<sub>2</sub> and the changes of grain size of α-Al<sub>2</sub>O<sub>3</sub> and ZrO<sub>2</sub>.
文摘Extrusion-Compression molded isotactic polypropylene (iPP) composites containing 10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt% of talc filler were studied by scanning electron microscopy (SEM), simultaneous thermal analysis (STA) and physical testing. The scanning electron microscope (SEM) micrographs of neat iPP and composites with 10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt% talc content show that neat PP, 10 wt%, 20 wt%, and 30wt% talc composites surface is smooth in comparison to 40 wt% and 50 wt% talc composites. It is also observed that talc is dispersed uniformly in the matrix and this uniform dispersion is not decreased even with talc content as high as 30 wt% talc. The composites of 40 wt% and 50 wt% talc contain more crack, agglomerates or larger particles. Bulk density of the composites decreases with the increase of talc content. With the increase of percentage of talc and period of immersion, the water absorption (WA) increases. Thermal analyses indicate a considerable increase of thermal stability of the composites with filler addition.
文摘In this research work, (Bi<sub>2</sub>O<sub>3</sub>Fe<sub>2</sub>O<sub>3</sub>)<sub>0.4</sub>(Nb<sub>2</sub>O<sub>5</sub>)<sub>0.6</sub> was made by the solid state reaction method. Samples were sintered at four different temperatures (850°C, 925°C, 1000°C and 1150°C) to study the effect of sintering temperature on the various properties of the samples. X-ray diffraction analysis confirmed that single phase Bi<sub>1.721</sub>δ<sub>0.089</sub>Fe<sub>1.056</sub>Nb<sub>1.134</sub>O<sub>7</sub> was found when sintering temperature increased. At the same time, larger grain size was found when sintering temperature increased. From variation of dielectric loss with respect to frequency, a small peak was found when sample was sintered at higher temperature (1150°C). Dielectric constant of the sample decreases with the increase of frequency for all the samples. With the variation of temperature, DC resistivity of the samples showed that resistivity decreases with the increase of measuring temperature which indicates semiconducting nature.
