Underground mine pillars provide natural stability to the mine area,allowing safe operations for workers and machinery.Extensive prior research has been conducted to understand pillar failure mechanics and design safe...Underground mine pillars provide natural stability to the mine area,allowing safe operations for workers and machinery.Extensive prior research has been conducted to understand pillar failure mechanics and design safe pillar layouts.However,limited studies(mostly based on empirical field observation and small-scale laboratory tests)have considered pillar-support interactions under monotonic loading conditions for the design of pillar-support systems.This study used a series of large-scale laboratory compression tests on porous limestone blocks to analyze rock and support behavior at a sufficiently large scale(specimens with edge length of 0.5 m)for incorporation of actual support elements,with consideration of different w/h ratios.Both unsupported and supported(grouted rebar rockbolt and wire mesh)tests were conducted,and the surface deformations of the specimens were monitored using three-dimensional(3D)digital image correlation(DIC).Rockbolts instrumented with distributed fiber optic strain sensors were used to study rockbolt strain distribution,load mobilization,and localized deformation at different w/h ratios.Both axial and bending strains were observed in the rockbolts,which became more prominent in the post-peak region of the stress-strain curve.展开更多
Ground control is the science of studying and controlling the behavior of rock strata in response to mining operations. Ground control-related research has seen significant advancements over the last 37 years, and the...Ground control is the science of studying and controlling the behavior of rock strata in response to mining operations. Ground control-related research has seen significant advancements over the last 37 years, and these accomplishments are well documented in the proceedings of the annual International Conference on Ground Control in Mining (ICGCM)(1)The ICGCM is a forum to promote closer communication among researchers, consultants。展开更多
Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to...Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site.The roof behavior in the headgate near the face was carefully observed during longwall retreat.Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.展开更多
Dynamic failures, or ‘‘bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. The presence of spatially discrete, stiff roof units are ...Dynamic failures, or ‘‘bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. The presence of spatially discrete, stiff roof units are one feature that has been linked to these events. However, an empirical stratigraphic review indicates that no significant difference exists in the relative commonality of discrete units between bumping and non-bumping deposits. Instead an apparent relationship exists between reportable bumping and the overall stiffness of the host rock. However, this initial study is too simplistic to be conclusive; to weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation—i.e., in a setting where all other variables are held constant.Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic ‘‘types",Compliant, Intermediate and Stiff. A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture-induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. This finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a holistic view of overburden lithology and site-specific numerical modelling may be necessary to improve miner safety.展开更多
Bumps and other types of dynamic failure have been a persistent, worldwide problem in the underground coal mining industry, spanning decades.For example, in just five states in the U.S.from 1983 to 2014,there were 388...Bumps and other types of dynamic failure have been a persistent, worldwide problem in the underground coal mining industry, spanning decades.For example, in just five states in the U.S.from 1983 to 2014,there were 388 reportable bumps.Despite significant advances in mine design tools and mining practices,these events continue to occur.Many conditions have been associated with bump potential, such as the presence of stiff units in the local geology.The effect of a stiff sandstone unit on the potential for coal bumps depends on the location of the stiff unit in the stratigraphic column, the relative stiffness and strength of other structural members, and stress concentrations caused by mining.This study describes the results of a robust design to consider the impact of different lithologic risk factors impacting dynamic failure risk.Because the inherent variability of stratigraphic characteristics in sedimentary formations,such as thickness, engineering material properties, and location, is significant and the number of influential parameters in determining a parametric study is large, it is impractical to consider every simulation case by varying each parameter individually.Therefore, to save time and honor the statistical distributions of the parameters, it is necessary to develop a robust design to collect sufficient sample data and develop a statistical analysis method to draw accurate conclusions from the collected data.In this study,orthogonal arrays, which were developed using the robust design, are used to define the combination of the(a) thickness of a stiff sandstone inserted on the top and bottom of a coal seam in a massive shale mine roof and floor,(b) location of the stiff sandstone inserted on the top and bottom of the coal seam,and(c) material properties of the stiff sandstone and contacts as interfaces using the 3-dimensional numerical model, FLAC3D.After completion of the numerical experiments, statistical and multivariate analysis are performed using the calculated results from the orthogonal arrays to analyze the effect of these variables.As a consequence, the impact of each of the parameters on the potential for bumps is quantitatively classified in terms of a normalized intensity of plastic dissipated energy.By multiple regression, the intensity of plastic dissipated energy and migration of the risk from the roof to the floor via the pillars is predicted based on the value of the variables.The results demonstrate and suggest a possible capability to predict the bump potential in a given rock mass adjacent to the underground excavations and pillars.Assessing the risk of bumps is important to preventing fatalities and injuries resulting from bumps.展开更多
A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports,or shields.The objective of the study was to develop a ...A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports,or shields.The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances.This paper will outline the design parameters for the development of thesystem,as well as describe baseline testing of coal and limestone dust.Results show that the average instantaneous respirable dust concentrated during simulated shield advance.Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device.展开更多
Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as oth...Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health(NIOSH) Mine Roof Simulator(MRS) as part of manufacturers' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs. dualwalled bag designs to the support capacity, stiffness, load shedding events, and yield characteristics.展开更多
A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face.In this approach, a systematic procedur...A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face.In this approach, a systematic procedure is used to estimate the model's inputs.Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements.Coal is modeled with a newly developed coal mass model.The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments.The model results were verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States.展开更多
A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National In...A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National Institute for Occupational Safety and Health(NIOSH) and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia.Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity.In order to use the geology as a forecaster of mining-induced seismic events and their energy potential, two primary components are needed.The first component is a long history of recorded seismic events with accurately plotted locations.The second component is a high density of geologic data within the mining area.In this case, 181 events of 1.0 MLor greater were recorded by the mine's seismic network between January, 2009, and October, 2016.Within the mining area, 897 geophysical logs, 224 core holes, and 1031 fiberscope holes were examined by mine geologists.From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations.After the data was analyzed, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions.Three forecast maps were created based on geology of previous seismic locations.The forecast maps have shown an accuracy of within 74%–89% when compared to the recorded 181 events that were1.0 MLor greater when considering three major geological criteria of overburden thickness of 579.12 m or greater, 6.096–12.192 m of sandstone within 15.24 m of the Pocahontas number 3 seam, and a longwall caving height of 4.572 m or less.展开更多
Methods of improving seismic event locations were investigated as part of a research study aimed at reducing ground control safety hazards. Seismic event waveforms collected with a 23-station three-dimensional sensor ...Methods of improving seismic event locations were investigated as part of a research study aimed at reducing ground control safety hazards. Seismic event waveforms collected with a 23-station three-dimensional sensor array during longwall coal mining provide the data set used in the analyses. A spatially variable seismic velocity model is constructed using seismic event sources in a passive tomographic method. The resulting three-dimensional velocity model is used to relocate seismic event positions. An evolutionary optimization algorithm is implemented and used in both the velocity model development and in seeking improved event location solutions. Results obtained using the different velocity models are compared. The combination of the tomographic velocity model development and evolutionary search algorithm provides improvement to the event locations.展开更多
Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recov...Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recovery increases in multiple-seam mining conditions.The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave.When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction.This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 21 m of interburden under about 305 m of depth of cover.The study finds that, for interburden thickness of 21 m, the multiple-seam mining influence zone in the lower seam is directly under the barrier pillar within about 30 m from the gob edge of the upper seam.The peak stress in the interburden transfers down at an angle of approximately 20°away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat.The study also suggests that, for full pillar recovery in close-distance multiple-seam scenarios,it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars.If the entries and/or crosscuts in the lower seam are developed outside the gob line of the upper seam,additional roof and rib support needs to be considered to account for the elevated stress in the multiple-seam influence zone.展开更多
A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia.Monitoring was initiated a few days after dev...A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia.Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry.Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation,stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site.During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading while minor changes were detected in roof deformation.As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 10–15 m of the instrumented locations.After reaching the peak loading at about 50–75 mm of roof sag, the cable bolts started to unload, and load was transferred to the standing supports.The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed.The results were used to calibrate modeled cable bolt response to field data, and to validate numerical modeling procedures that have been developed to evaluate entry support systems.It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location.The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.展开更多
Why do some room and pillar retreat panels encounter abnormal conditions？ What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal...Why do some room and pillar retreat panels encounter abnormal conditions？ What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered7 To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar （R ＆ P） retreat min- ing entries, four consecutive R ＆ P retreat panels were evaluated. This evaluation was intended to rein- force the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry. This paper details observations were made in four consecutive R ＆ P retreat panels and the data were collected from an instrumentation site during retreat mining. The pri- mary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the obse^ation and ｜ll^trumentation, numerical modeling was per- formed to evaluate the stress condi~!ons. Both the LaModel 3.0 and Rocscience Phase 2 programs were used to evaluate these four panels, The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine. These efforts provided two overarching conclusions concerning R ＆ P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R ＆ P retreat mining： topographic relief, multiple^seaPa stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R ＆ P panel, a three-phased approach to the design and analysis of the panel should be conducted： the planning phase, evaluation phase, and monitoring phase.展开更多
Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in ga...Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings.If the gas well casings are compromised or ruptured,natural gas could migrate into the mine workings,potentially causing a fire or explosion.By the current safety regulations,the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars.The current regulations for gas well pillar design are based on the 1957 Pennsylvania gas well pillar study.The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars.As the guidelines were developed for room-andpillar mining under shallow cover,they are no longer applicable to modern longwall coal mining,particularly,under deep cover.Gas well casing of failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study,conducted by the National Institute for Occupational Safety and Health(NIOSH),presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh Coal Seam.The study results indicate that overburden depth and pillar size are not the only determining factors for gas well stability.The other important factors include subsurface ground movement,overburden geology,weak floor,as well as the type of the construction of gas wells.Numerical modeling was used to model abutment pressure,subsurface deformations,and the response of gas well casings.The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above,within,and below the chain pillars,and the potential location and modes of gas well failures,thereby providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.展开更多
This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health(NIOSH)from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on s...This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health(NIOSH)from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health.At both deep-cover and shallow-cover instrumentation sites,surface subsidence measurements,subsurface inplace inclinometer measurements,and underground pillar pressure measurements were conducted as longwall panels were mined.Comparisons of the deep-cover and shallow-cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario.Under shallow and medium covers,measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover.On the other hand,measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers.However,FLAC3 Dsimulations of the casings indicate that,in all three cases,the P-110 production casings remain intact under longwall-induced deformations and compressions,which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.展开更多
Longwall abutment loads are influenced by several factors,including depth of cover,pillar sizes,panel dimensions,geological setting,mining height,proximity to gob,intersection type,and size of the gob.How does proximi...Longwall abutment loads are influenced by several factors,including depth of cover,pillar sizes,panel dimensions,geological setting,mining height,proximity to gob,intersection type,and size of the gob.How does proximity to the gob affect pillar loading and entry condition?Does the gob influence depend on whether the abutment load is a forward,side,or rear loading?Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts?If not,will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel—specifically,data collected from borehole pressure cells and roof extensometers,observations of the conditions of the entries,and numerical modeling of the bleeder entries during longwall extraction.The primary focus was on the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels.Due to the layout of the longwall panels and bleeder entries,the borehole pressure cells(BPCs)and roof extensometers did not show much change due to the advancing of the first longwall.However,they did show a noticeable increase due to the second longwall advancement,with a maximum of about 4 MPa of pressure increase and 5mmof roof deformation.The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 m.Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as well as an increase in water in the entries.In addition to the observations and instrumentation,numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design.ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries.The results of the models indicated only a minor increase in load during the extraction of the longwall panels.These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries--about 80%development and 20%longwall extraction.The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction.The front and side abutment extent modeled was very similar to observations from this and previous panels.展开更多
Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines.Adequately designing pillars and other support mea...Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines.Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them,as well as the load-bearing capacities of the supports.There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design.The empirical methods are based on equations derived from large databases of various case studies.They are implemented in government approved design tools and are widely used.There are also analytical and numerical techniques used for more detailed analysis of the induced loads.In this study,two different longwall mines with different panel width-to-depth ratios are analyzed using different methods.The empirical method used in the analysis is the square-decay stress function that uses the abutment angle concept,implemented in pillar design software developed by the National Institute for Occupational Safety and Health(NIOSH).The first numerical method used in the analysis is a displacement-discontinuity(DD)variation of the boundary element method,LaModel,which utilizes the laminated overburden model.The second numerical method used in the analysis is Fast Lagrangian Analysis of Continua(FLAC)with the numerical modeling approach recently developed at West Virginia University which is based on the approach developed by NIOSH.The model includes the 2D slice of a cross-section along the width of the panel with the chain pillar system that also includes the different stratigraphic layers of the overburden.All three methods gave similar results for the shallow mine,both in terms of load percentages and distribution where the variation was more obvious for the deep cover mine.The FLAC3D model was observed to better capture the stress changes observed during the field measurements for both the shallow and deep cover cases.This study allowed us to see the shortcomings of each of these different methods.It was concluded that a numerical model which incorporates the site-specific geology would provide the most precise estimate for complex loading conditions.展开更多
While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex, with differen...While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex, with different branches that reactivate at different times. Furthermore, these branches are zones of nonzero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D software program. The initial and boundary conditions are simplified, and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.展开更多
基金the funding support from Alpha Foundation for the Improvement of Mine Safety and Health Inc.(ALPHAFOUNDATION,Grant No.AFC820-52)。
文摘Underground mine pillars provide natural stability to the mine area,allowing safe operations for workers and machinery.Extensive prior research has been conducted to understand pillar failure mechanics and design safe pillar layouts.However,limited studies(mostly based on empirical field observation and small-scale laboratory tests)have considered pillar-support interactions under monotonic loading conditions for the design of pillar-support systems.This study used a series of large-scale laboratory compression tests on porous limestone blocks to analyze rock and support behavior at a sufficiently large scale(specimens with edge length of 0.5 m)for incorporation of actual support elements,with consideration of different w/h ratios.Both unsupported and supported(grouted rebar rockbolt and wire mesh)tests were conducted,and the surface deformations of the specimens were monitored using three-dimensional(3D)digital image correlation(DIC).Rockbolts instrumented with distributed fiber optic strain sensors were used to study rockbolt strain distribution,load mobilization,and localized deformation at different w/h ratios.Both axial and bending strains were observed in the rockbolts,which became more prominent in the post-peak region of the stress-strain curve.
文摘Ground control is the science of studying and controlling the behavior of rock strata in response to mining operations. Ground control-related research has seen significant advancements over the last 37 years, and these accomplishments are well documented in the proceedings of the annual International Conference on Ground Control in Mining (ICGCM)(1)The ICGCM is a forum to promote closer communication among researchers, consultants。
文摘Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site.The roof behavior in the headgate near the face was carefully observed during longwall retreat.Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.
文摘Dynamic failures, or ‘‘bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. The presence of spatially discrete, stiff roof units are one feature that has been linked to these events. However, an empirical stratigraphic review indicates that no significant difference exists in the relative commonality of discrete units between bumping and non-bumping deposits. Instead an apparent relationship exists between reportable bumping and the overall stiffness of the host rock. However, this initial study is too simplistic to be conclusive; to weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation—i.e., in a setting where all other variables are held constant.Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic ‘‘types",Compliant, Intermediate and Stiff. A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture-induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. This finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a holistic view of overburden lithology and site-specific numerical modelling may be necessary to improve miner safety.
文摘Bumps and other types of dynamic failure have been a persistent, worldwide problem in the underground coal mining industry, spanning decades.For example, in just five states in the U.S.from 1983 to 2014,there were 388 reportable bumps.Despite significant advances in mine design tools and mining practices,these events continue to occur.Many conditions have been associated with bump potential, such as the presence of stiff units in the local geology.The effect of a stiff sandstone unit on the potential for coal bumps depends on the location of the stiff unit in the stratigraphic column, the relative stiffness and strength of other structural members, and stress concentrations caused by mining.This study describes the results of a robust design to consider the impact of different lithologic risk factors impacting dynamic failure risk.Because the inherent variability of stratigraphic characteristics in sedimentary formations,such as thickness, engineering material properties, and location, is significant and the number of influential parameters in determining a parametric study is large, it is impractical to consider every simulation case by varying each parameter individually.Therefore, to save time and honor the statistical distributions of the parameters, it is necessary to develop a robust design to collect sufficient sample data and develop a statistical analysis method to draw accurate conclusions from the collected data.In this study,orthogonal arrays, which were developed using the robust design, are used to define the combination of the(a) thickness of a stiff sandstone inserted on the top and bottom of a coal seam in a massive shale mine roof and floor,(b) location of the stiff sandstone inserted on the top and bottom of the coal seam,and(c) material properties of the stiff sandstone and contacts as interfaces using the 3-dimensional numerical model, FLAC3D.After completion of the numerical experiments, statistical and multivariate analysis are performed using the calculated results from the orthogonal arrays to analyze the effect of these variables.As a consequence, the impact of each of the parameters on the potential for bumps is quantitatively classified in terms of a normalized intensity of plastic dissipated energy.By multiple regression, the intensity of plastic dissipated energy and migration of the risk from the roof to the floor via the pillars is predicted based on the value of the variables.The results demonstrate and suggest a possible capability to predict the bump potential in a given rock mass adjacent to the underground excavations and pillars.Assessing the risk of bumps is important to preventing fatalities and injuries resulting from bumps.
文摘A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports,or shields.The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances.This paper will outline the design parameters for the development of thesystem,as well as describe baseline testing of coal and limestone dust.Results show that the average instantaneous respirable dust concentrated during simulated shield advance.Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device.
文摘Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health(NIOSH) Mine Roof Simulator(MRS) as part of manufacturers' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs. dualwalled bag designs to the support capacity, stiffness, load shedding events, and yield characteristics.
文摘A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face.In this approach, a systematic procedure is used to estimate the model's inputs.Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements.Coal is modeled with a newly developed coal mass model.The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments.The model results were verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States.
文摘A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National Institute for Occupational Safety and Health(NIOSH) and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia.Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity.In order to use the geology as a forecaster of mining-induced seismic events and their energy potential, two primary components are needed.The first component is a long history of recorded seismic events with accurately plotted locations.The second component is a high density of geologic data within the mining area.In this case, 181 events of 1.0 MLor greater were recorded by the mine's seismic network between January, 2009, and October, 2016.Within the mining area, 897 geophysical logs, 224 core holes, and 1031 fiberscope holes were examined by mine geologists.From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations.After the data was analyzed, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions.Three forecast maps were created based on geology of previous seismic locations.The forecast maps have shown an accuracy of within 74%–89% when compared to the recorded 181 events that were1.0 MLor greater when considering three major geological criteria of overburden thickness of 579.12 m or greater, 6.096–12.192 m of sandstone within 15.24 m of the Pocahontas number 3 seam, and a longwall caving height of 4.572 m or less.
文摘Methods of improving seismic event locations were investigated as part of a research study aimed at reducing ground control safety hazards. Seismic event waveforms collected with a 23-station three-dimensional sensor array during longwall coal mining provide the data set used in the analyses. A spatially variable seismic velocity model is constructed using seismic event sources in a passive tomographic method. The resulting three-dimensional velocity model is used to relocate seismic event positions. An evolutionary optimization algorithm is implemented and used in both the velocity model development and in seeking improved event location solutions. Results obtained using the different velocity models are compared. The combination of the tomographic velocity model development and evolutionary search algorithm provides improvement to the event locations.
文摘Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recovery increases in multiple-seam mining conditions.The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave.When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction.This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 21 m of interburden under about 305 m of depth of cover.The study finds that, for interburden thickness of 21 m, the multiple-seam mining influence zone in the lower seam is directly under the barrier pillar within about 30 m from the gob edge of the upper seam.The peak stress in the interburden transfers down at an angle of approximately 20°away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat.The study also suggests that, for full pillar recovery in close-distance multiple-seam scenarios,it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars.If the entries and/or crosscuts in the lower seam are developed outside the gob line of the upper seam,additional roof and rib support needs to be considered to account for the elevated stress in the multiple-seam influence zone.
文摘A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia.Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry.Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation,stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site.During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading while minor changes were detected in roof deformation.As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 10–15 m of the instrumented locations.After reaching the peak loading at about 50–75 mm of roof sag, the cable bolts started to unload, and load was transferred to the standing supports.The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed.The results were used to calibrate modeled cable bolt response to field data, and to validate numerical modeling procedures that have been developed to evaluate entry support systems.It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location.The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.
文摘Why do some room and pillar retreat panels encounter abnormal conditions？ What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered7 To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar （R ＆ P） retreat min- ing entries, four consecutive R ＆ P retreat panels were evaluated. This evaluation was intended to rein- force the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry. This paper details observations were made in four consecutive R ＆ P retreat panels and the data were collected from an instrumentation site during retreat mining. The pri- mary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the obse^ation and ｜ll^trumentation, numerical modeling was per- formed to evaluate the stress condi~!ons. Both the LaModel 3.0 and Rocscience Phase 2 programs were used to evaluate these four panels, The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine. These efforts provided two overarching conclusions concerning R ＆ P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R ＆ P retreat mining： topographic relief, multiple^seaPa stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R ＆ P panel, a three-phased approach to the design and analysis of the panel should be conducted： the planning phase, evaluation phase, and monitoring phase.
文摘Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings.If the gas well casings are compromised or ruptured,natural gas could migrate into the mine workings,potentially causing a fire or explosion.By the current safety regulations,the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars.The current regulations for gas well pillar design are based on the 1957 Pennsylvania gas well pillar study.The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars.As the guidelines were developed for room-andpillar mining under shallow cover,they are no longer applicable to modern longwall coal mining,particularly,under deep cover.Gas well casing of failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study,conducted by the National Institute for Occupational Safety and Health(NIOSH),presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh Coal Seam.The study results indicate that overburden depth and pillar size are not the only determining factors for gas well stability.The other important factors include subsurface ground movement,overburden geology,weak floor,as well as the type of the construction of gas wells.Numerical modeling was used to model abutment pressure,subsurface deformations,and the response of gas well casings.The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above,within,and below the chain pillars,and the potential location and modes of gas well failures,thereby providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.
文摘This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health(NIOSH)from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health.At both deep-cover and shallow-cover instrumentation sites,surface subsidence measurements,subsurface inplace inclinometer measurements,and underground pillar pressure measurements were conducted as longwall panels were mined.Comparisons of the deep-cover and shallow-cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario.Under shallow and medium covers,measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover.On the other hand,measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers.However,FLAC3 Dsimulations of the casings indicate that,in all three cases,the P-110 production casings remain intact under longwall-induced deformations and compressions,which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.
文摘Longwall abutment loads are influenced by several factors,including depth of cover,pillar sizes,panel dimensions,geological setting,mining height,proximity to gob,intersection type,and size of the gob.How does proximity to the gob affect pillar loading and entry condition?Does the gob influence depend on whether the abutment load is a forward,side,or rear loading?Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts?If not,will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel—specifically,data collected from borehole pressure cells and roof extensometers,observations of the conditions of the entries,and numerical modeling of the bleeder entries during longwall extraction.The primary focus was on the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels.Due to the layout of the longwall panels and bleeder entries,the borehole pressure cells(BPCs)and roof extensometers did not show much change due to the advancing of the first longwall.However,they did show a noticeable increase due to the second longwall advancement,with a maximum of about 4 MPa of pressure increase and 5mmof roof deformation.The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 m.Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as well as an increase in water in the entries.In addition to the observations and instrumentation,numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design.ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries.The results of the models indicated only a minor increase in load during the extraction of the longwall panels.These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries--about 80%development and 20%longwall extraction.The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction.The front and side abutment extent modeled was very similar to observations from this and previous panels.
文摘Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines.Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them,as well as the load-bearing capacities of the supports.There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design.The empirical methods are based on equations derived from large databases of various case studies.They are implemented in government approved design tools and are widely used.There are also analytical and numerical techniques used for more detailed analysis of the induced loads.In this study,two different longwall mines with different panel width-to-depth ratios are analyzed using different methods.The empirical method used in the analysis is the square-decay stress function that uses the abutment angle concept,implemented in pillar design software developed by the National Institute for Occupational Safety and Health(NIOSH).The first numerical method used in the analysis is a displacement-discontinuity(DD)variation of the boundary element method,LaModel,which utilizes the laminated overburden model.The second numerical method used in the analysis is Fast Lagrangian Analysis of Continua(FLAC)with the numerical modeling approach recently developed at West Virginia University which is based on the approach developed by NIOSH.The model includes the 2D slice of a cross-section along the width of the panel with the chain pillar system that also includes the different stratigraphic layers of the overburden.All three methods gave similar results for the shallow mine,both in terms of load percentages and distribution where the variation was more obvious for the deep cover mine.The FLAC3D model was observed to better capture the stress changes observed during the field measurements for both the shallow and deep cover cases.This study allowed us to see the shortcomings of each of these different methods.It was concluded that a numerical model which incorporates the site-specific geology would provide the most precise estimate for complex loading conditions.
文摘While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex, with different branches that reactivate at different times. Furthermore, these branches are zones of nonzero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D software program. The initial and boundary conditions are simplified, and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.
