Solution and aging treatment were conducted on the laser directed energy deposition(LDED)-prepared carbon nanotubes(CNTs)-reinforced WE43(CNTs/WE43)layers to optimize their microstructure and surface properties in thi...Solution and aging treatment were conducted on the laser directed energy deposition(LDED)-prepared carbon nanotubes(CNTs)-reinforced WE43(CNTs/WE43)layers to optimize their microstructure and surface properties in this study.The microstructure of the WE43 and CNTs/WE43 layers was systematically compared.The dissolution of divorced eutectics at the grain boundaries was retarded by CNTs during solution treatment.The spot segregation composed of Mg_(24)Y_(5),CNTs,and Zr cores in the solution treated CNTs/WE43 layer presented a slight decreasing in Y content.The grain growth of both types of layers underwent three stages:slow,rapid,and steady-state.The significant inhibitory effect of CNTs on the grain growth of the LDED WE43 matrix was more pronounced than the promoting effect of temperature,resulting in a 47%increase at 510℃ and a 35%increase at 540℃ in the grain growth exponent compared to the WE43 layers at 510℃.During the subsequent aging treatment at 225℃,the precipitation sequences from plate-shaped β″to plate-shaped and globular β′ were observed in both types of layers.CNTs can facilitate an increase in the nucleation rate of precipitates,but without accelerating precipitation hardening rate.The long and short diameters of the precipitates in peak-aged state were decreased by 48.5%and 43.1%by addition of CNTs,respectively.The wear resistance of both the WE43 and CNTs/WE43 layers can be significantly enhanced through solution and aging treatment.The enhancement in wear resistance for the CNTs/WE43 layers is considerably greater than that of the WE43 layers.展开更多
Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restr...Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restricting widespread use.In this study,ultra-fine-grained and homogeneous Mg alloys were fabricated using double-sided friction stir processing(DS-FSP)with liquid CO_(2) rapid cooling,leading to a significant enhancement in the strength-ductility synergy of the stirred zone.The results demonstrate that DS-FSP samples exhibit simultaneous improvements in ultimate tensile strength(UTS)and elongation,reaching 334.1±15 MPa and 28.2±7.3%,respectively.Compared to the non-uniform fine-grained microstructure obtained through single-sided friction stir processing,DS-FSP generates a uniform ultra-fine-grained structure,fundamentally altering the fracture behavior and mechanisms of Mg alloys.The DS-FSP samples exhibit irregular fracture patterns due to variations in basal slip system activation among different grains.In contrast,single-sided friction stir processing samples,characterized by a fine-grained yet heterogeneous microstructure,display flat shear fractures dominated by high-density dislocation initiation induced by twin formation,with fracture propagation dictated by the non-uniform texture.By achieving an ultra-fine grain size and homogeneous texture,DS-FSP effectively modifies the fracture mechanisms,thereby enhancing the strength-ductility balance of bio-magnesium alloys.展开更多
Although magnesium(Mg)alloys are the lightest among structural metals,their inadequate corrosion resistance makes them difficult to be used in energy-saving lightweight structures.Moreover,the improvement in corrosion...Although magnesium(Mg)alloys are the lightest among structural metals,their inadequate corrosion resistance makes them difficult to be used in energy-saving lightweight structures.Moreover,the improvement in corrosion resistance by the conventional surface treatments is always achieved at the expense of sacrificing the fatigue lifetime.In this study,high purity aluminum(Al)and AlMgSi alloy coatings were deposited on Mg alloys via an in-situ micro-forging(MF)assisted cold spray(MFCS)process for simultaneous higher corrosion resistance and longer fatigue lifetime.Besides contributing to a highly dense microstructure,the in-situ MF also greatly refines the grain of the deposited Al alloy coating to the sub-micrometer range due to the enhanced dynamic recrystallization and also generates notable compressive residual stress up to 210 MPa within the AlMgSi coating.The absence of secondary phases in the AlMgSi alloy coatings enable the coated Mg alloy with corrosion resistance,which is even better than its bulk AlMgSi counterparts.The unique combination of refined microstructure and the prominent compressive residual stress within the AlMgSi coatings,effectively delayed the crack initiation upon repeated dynamic loading,thereby leading to∼10 times increase in the fatigue lifetime of the Mg Alloy.However,although residual stress is also generated in the submmicro-sized grained pure Al coating,the low intrinsic strength of the coating layer leads to a lower fatigue lifetime than the uncoated Mg alloy substrate.The present work is aimed to provide a facile approach to break the trade-off between corrosion resistance improvement and fatigue lifetime of the coated Mg alloys.展开更多
The effects of 2%Ca addition on the microstructure and the mechanical properties of the asymmetric double-sided friction stir welded magnesium alloy AZ61 were investigated.Compared to the Ca-free AZ61magnesium alloy,t...The effects of 2%Ca addition on the microstructure and the mechanical properties of the asymmetric double-sided friction stir welded magnesium alloy AZ61 were investigated.Compared to the Ca-free AZ61magnesium alloy,the addition of 2%Ca significantly refines the grains in the stir zone after welding.Due to the existence of thermally stable Al2Ca particles,there is no noticeable change in the grain size in the stir zone regardless of the welding heat input.The electron backscattered diffraction analysis at the center of the stir zone confirmed the significant deterioration of the(0001)texture strength from the addition of 2%Ca.The tensile test of the joint suggested that the addition of 2%Ca provides stable tensile properties to the joint regardless of the welding parameters.The critical(0001)texture strength that determines the ultimate tensile strength decreased from 20 to 15 by the Ca addition.The addition of Ca enhanced the deterioration of the plastic elongation when the(0001)texture strength increased.展开更多
The paper describes recent trends to carry forward the automation in welding process in Japanese industries.The present situation on the introduction of computer integrated manufacturing is surveyed and its concept an...The paper describes recent trends to carry forward the automation in welding process in Japanese industries.The present situation on the introduction of computer integrated manufacturing is surveyed and its concept and relation among the constituent subsystems are shown.Also recent developments of arc welding processes and related tools are reviewed.They are as follows.1) Schematic image of the structure of computer integrated manufacturing system (CIM).2) Short descriptions for the trend of introducing CIM system.An example of multi-robot welding system in shipyard,virtual factory,network monitoring of welding quality,clarification of welder’s skill.3) Development of high efficiency welding processes.Copper-less wire electrode,tandem large fillet welding,tandem pulse GMA welding,digital wire feeder with new!push-pull system,overhead horizontal tandem GMA welding for ship bottom shell,one-sided fillet groove GMA welding for construction machinery,ultra-NGW hot wire GTA process,Al-alloy sheet welding with laser assisted AC pulsed MIG process.展开更多
A computational approach based on the thermal elastic plastic finite element method was developed for predicting welding residual stress in low carbon alloyed steel welds by taking into account the effect of the solid...A computational approach based on the thermal elastic plastic finite element method was developed for predicting welding residual stress in low carbon alloyed steel welds by taking into account the effect of the solid-state phase transformations. The kinetics of phase transformations was described by Johnson Mehl Avrami Kolmogrov （JMAK） equation for bainitic transition and by Koistinen-Marburger （K-M） relationship for martensitic transition. Moreover, an additive rule depending on volumetric phase fraction was adopted to represent the material property changes during heating and cooling. Consequently, the residual welding stresses in a 2.25Cr1Mo steel TIG welded plate were computed. Early calculation results suggest that the bainitic and martensitic transformations took place in the weld the heat-affected zone drastically reduce the residual longitudinal tensile stress in the region.展开更多
Elemental titanium(Ti)and nickel(Ni)powders were consolidated by spark plasma sintering(SPS)to fabricate Ti-51%Ni(mole fraction)shape-memory alloys(SMAs).The objective of this study is to enhance the superelasticity o...Elemental titanium(Ti)and nickel(Ni)powders were consolidated by spark plasma sintering(SPS)to fabricate Ti-51%Ni(mole fraction)shape-memory alloys(SMAs).The objective of this study is to enhance the superelasticity of SPS produced Ti-Ni alloy using free forging as a secondary process.Products from two processes(with and without free forging)were compared in terms of microstructure,transformation temperature and superelasticity.The results showed that,free forging effectively improved the tensile and shape-memory properties.Ductility increased from 6.8%to 9.2%after forging.The maximum strain during superelasticity increased from 5%to 7.5%and the strain recovery rate increased from 72%to 92%.The microstructure of produced Ti-51%Ni SMA consists of the cubic austenite(B2)matrix,monoclinic martensite(B19′),secondary phases(Ti3Ni4,Ti2Ni and TiNi3)and oxides(Ti4Ni2O and Ti3O5).There was a shift towards higher temperatures in the martensitic transformation of free forged specimen(aged at 500°C)due to the decrease in Ni content of B2 matrix.This is related to the presence of Ti3Ni4 precipitates,which were observed using transmission electron microscope(TEM).In conclusion,free forging could improve superelasticity and mechanical properties of Ti-51%Ni SMA.展开更多
An ultrasonic evaluation method of echo feature of diffusion bond joint between two dissimilar materials is presented. The echo signal was acquired by an automatic ultrasonic C-scan test system. It is found that the i...An ultrasonic evaluation method of echo feature of diffusion bond joint between two dissimilar materials is presented. The echo signal was acquired by an automatic ultrasonic C-scan test system. It is found that the intensity of echo and its phase can be used to evaluate the joint quality, and interface products of dissimilar materials bonding can be evaluated by ultrasonic method.展开更多
In this study, the effect of the processing route using a friction stir processing(FSP) method on the microstructure and mechanical behavior of a Mg-9Li-1Zn alloy was systematically investigated. In the FSP method, th...In this study, the effect of the processing route using a friction stir processing(FSP) method on the microstructure and mechanical behavior of a Mg-9Li-1Zn alloy was systematically investigated. In the FSP method, the odd-numbered(1st and 3rd) process directions and even-numbered(2nd and 4th) passes were alternated to distribute the strain throughout the whole processed zone uniformly. Consequently, the processed zone had a much more uniform microstructure and hardness distribution than the processed zone obtained using the conventional FSP method. Using this method, the grain size of a Mg-9Li-1Zn sheet alloy was refined from ~31 μm to ~0.21 μm with uniformly distributedα and β phases. The processed alloy exhibited a high strength-ductility synergy with an ultimate tensile strength(UTS) of 220.1 MPa and total elongation of 70.0% at a strain rate of 10^(-3)s^(-1), overwhelmingly higher than those of the base metal, 155.6 MPa in UTS and 36.0%in elongation. The in-situ SEM-DIC analysis and TEM observation demonstrated that such an outstanding ductility with moderate strength is caused by grain boundary sliding, the dominant deformation mechanism of the ultra-fine-grained sample after FSP. The processing route with reverse processing direction was proven to be efficient in producing the ultrafine grain size microstructure and improving the mechanical properties of superlight Mg-9Li-1Zn alloy.展开更多
基金supported by the National Natural Science Foundation of China(52005264).
文摘Solution and aging treatment were conducted on the laser directed energy deposition(LDED)-prepared carbon nanotubes(CNTs)-reinforced WE43(CNTs/WE43)layers to optimize their microstructure and surface properties in this study.The microstructure of the WE43 and CNTs/WE43 layers was systematically compared.The dissolution of divorced eutectics at the grain boundaries was retarded by CNTs during solution treatment.The spot segregation composed of Mg_(24)Y_(5),CNTs,and Zr cores in the solution treated CNTs/WE43 layer presented a slight decreasing in Y content.The grain growth of both types of layers underwent three stages:slow,rapid,and steady-state.The significant inhibitory effect of CNTs on the grain growth of the LDED WE43 matrix was more pronounced than the promoting effect of temperature,resulting in a 47%increase at 510℃ and a 35%increase at 540℃ in the grain growth exponent compared to the WE43 layers at 510℃.During the subsequent aging treatment at 225℃,the precipitation sequences from plate-shaped β″to plate-shaped and globular β′ were observed in both types of layers.CNTs can facilitate an increase in the nucleation rate of precipitates,but without accelerating precipitation hardening rate.The long and short diameters of the precipitates in peak-aged state were decreased by 48.5%and 43.1%by addition of CNTs,respectively.The wear resistance of both the WE43 and CNTs/WE43 layers can be significantly enhanced through solution and aging treatment.The enhancement in wear resistance for the CNTs/WE43 layers is considerably greater than that of the WE43 layers.
基金financial support from the National Key Research and Development Program of China(2021YFC2400703)Zhengzhou City Major Special Project for Collaborative InnovationChina Scholarship Council。
文摘Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restricting widespread use.In this study,ultra-fine-grained and homogeneous Mg alloys were fabricated using double-sided friction stir processing(DS-FSP)with liquid CO_(2) rapid cooling,leading to a significant enhancement in the strength-ductility synergy of the stirred zone.The results demonstrate that DS-FSP samples exhibit simultaneous improvements in ultimate tensile strength(UTS)and elongation,reaching 334.1±15 MPa and 28.2±7.3%,respectively.Compared to the non-uniform fine-grained microstructure obtained through single-sided friction stir processing,DS-FSP generates a uniform ultra-fine-grained structure,fundamentally altering the fracture behavior and mechanisms of Mg alloys.The DS-FSP samples exhibit irregular fracture patterns due to variations in basal slip system activation among different grains.In contrast,single-sided friction stir processing samples,characterized by a fine-grained yet heterogeneous microstructure,display flat shear fractures dominated by high-density dislocation initiation induced by twin formation,with fracture propagation dictated by the non-uniform texture.By achieving an ultra-fine grain size and homogeneous texture,DS-FSP effectively modifies the fracture mechanisms,thereby enhancing the strength-ductility balance of bio-magnesium alloys.
基金supported by the National Natural Science Foundation of China(51875443)Guangdong Basic and Applied Basic Research Foundation(2019B1515120016,202002030290).
文摘Although magnesium(Mg)alloys are the lightest among structural metals,their inadequate corrosion resistance makes them difficult to be used in energy-saving lightweight structures.Moreover,the improvement in corrosion resistance by the conventional surface treatments is always achieved at the expense of sacrificing the fatigue lifetime.In this study,high purity aluminum(Al)and AlMgSi alloy coatings were deposited on Mg alloys via an in-situ micro-forging(MF)assisted cold spray(MFCS)process for simultaneous higher corrosion resistance and longer fatigue lifetime.Besides contributing to a highly dense microstructure,the in-situ MF also greatly refines the grain of the deposited Al alloy coating to the sub-micrometer range due to the enhanced dynamic recrystallization and also generates notable compressive residual stress up to 210 MPa within the AlMgSi coating.The absence of secondary phases in the AlMgSi alloy coatings enable the coated Mg alloy with corrosion resistance,which is even better than its bulk AlMgSi counterparts.The unique combination of refined microstructure and the prominent compressive residual stress within the AlMgSi coatings,effectively delayed the crack initiation upon repeated dynamic loading,thereby leading to∼10 times increase in the fatigue lifetime of the Mg Alloy.However,although residual stress is also generated in the submmicro-sized grained pure Al coating,the low intrinsic strength of the coating layer leads to a lower fatigue lifetime than the uncoated Mg alloy substrate.The present work is aimed to provide a facile approach to break the trade-off between corrosion resistance improvement and fatigue lifetime of the coated Mg alloys.
基金This study was partially supported by the New Energy and Industrial Technology Development Organization(NEDO)under the“Innovation Structural Materials Project(Future Pioneering Projects)”.
文摘The effects of 2%Ca addition on the microstructure and the mechanical properties of the asymmetric double-sided friction stir welded magnesium alloy AZ61 were investigated.Compared to the Ca-free AZ61magnesium alloy,the addition of 2%Ca significantly refines the grains in the stir zone after welding.Due to the existence of thermally stable Al2Ca particles,there is no noticeable change in the grain size in the stir zone regardless of the welding heat input.The electron backscattered diffraction analysis at the center of the stir zone confirmed the significant deterioration of the(0001)texture strength from the addition of 2%Ca.The tensile test of the joint suggested that the addition of 2%Ca provides stable tensile properties to the joint regardless of the welding parameters.The critical(0001)texture strength that determines the ultimate tensile strength decreased from 20 to 15 by the Ca addition.The addition of Ca enhanced the deterioration of the plastic elongation when the(0001)texture strength increased.
文摘The paper describes recent trends to carry forward the automation in welding process in Japanese industries.The present situation on the introduction of computer integrated manufacturing is surveyed and its concept and relation among the constituent subsystems are shown.Also recent developments of arc welding processes and related tools are reviewed.They are as follows.1) Schematic image of the structure of computer integrated manufacturing system (CIM).2) Short descriptions for the trend of introducing CIM system.An example of multi-robot welding system in shipyard,virtual factory,network monitoring of welding quality,clarification of welder’s skill.3) Development of high efficiency welding processes.Copper-less wire electrode,tandem large fillet welding,tandem pulse GMA welding,digital wire feeder with new!push-pull system,overhead horizontal tandem GMA welding for ship bottom shell,one-sided fillet groove GMA welding for construction machinery,ultra-NGW hot wire GTA process,Al-alloy sheet welding with laser assisted AC pulsed MIG process.
基金supported by the Open-Fund Research of State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Chinathe Fundamental Research Funds for Central University (No. CDJZR12130036)
文摘A computational approach based on the thermal elastic plastic finite element method was developed for predicting welding residual stress in low carbon alloyed steel welds by taking into account the effect of the solid-state phase transformations. The kinetics of phase transformations was described by Johnson Mehl Avrami Kolmogrov （JMAK） equation for bainitic transition and by Koistinen-Marburger （K-M） relationship for martensitic transition. Moreover, an additive rule depending on volumetric phase fraction was adopted to represent the material property changes during heating and cooling. Consequently, the residual welding stresses in a 2.25Cr1Mo steel TIG welded plate were computed. Early calculation results suggest that the bainitic and martensitic transformations took place in the weld the heat-affected zone drastically reduce the residual longitudinal tensile stress in the region.
基金the Ministry of Higher Education of Malaysia for the Malaysian International Scholarship and research funding under FRGS vote No. R.J13000.7824.4F810
文摘Elemental titanium(Ti)and nickel(Ni)powders were consolidated by spark plasma sintering(SPS)to fabricate Ti-51%Ni(mole fraction)shape-memory alloys(SMAs).The objective of this study is to enhance the superelasticity of SPS produced Ti-Ni alloy using free forging as a secondary process.Products from two processes(with and without free forging)were compared in terms of microstructure,transformation temperature and superelasticity.The results showed that,free forging effectively improved the tensile and shape-memory properties.Ductility increased from 6.8%to 9.2%after forging.The maximum strain during superelasticity increased from 5%to 7.5%and the strain recovery rate increased from 72%to 92%.The microstructure of produced Ti-51%Ni SMA consists of the cubic austenite(B2)matrix,monoclinic martensite(B19′),secondary phases(Ti3Ni4,Ti2Ni and TiNi3)and oxides(Ti4Ni2O and Ti3O5).There was a shift towards higher temperatures in the martensitic transformation of free forged specimen(aged at 500°C)due to the decrease in Ni content of B2 matrix.This is related to the presence of Ti3Ni4 precipitates,which were observed using transmission electron microscope(TEM).In conclusion,free forging could improve superelasticity and mechanical properties of Ti-51%Ni SMA.
文摘An ultrasonic evaluation method of echo feature of diffusion bond joint between two dissimilar materials is presented. The echo signal was acquired by an automatic ultrasonic C-scan test system. It is found that the intensity of echo and its phase can be used to evaluate the joint quality, and interface products of dissimilar materials bonding can be evaluated by ultrasonic method.
基金partially supported by the JST-Mirai Program Grant Number JPMJMI19E5a Grant-in-Aid for Science Research from the Japan Society for the Promotion of Science。
文摘In this study, the effect of the processing route using a friction stir processing(FSP) method on the microstructure and mechanical behavior of a Mg-9Li-1Zn alloy was systematically investigated. In the FSP method, the odd-numbered(1st and 3rd) process directions and even-numbered(2nd and 4th) passes were alternated to distribute the strain throughout the whole processed zone uniformly. Consequently, the processed zone had a much more uniform microstructure and hardness distribution than the processed zone obtained using the conventional FSP method. Using this method, the grain size of a Mg-9Li-1Zn sheet alloy was refined from ~31 μm to ~0.21 μm with uniformly distributedα and β phases. The processed alloy exhibited a high strength-ductility synergy with an ultimate tensile strength(UTS) of 220.1 MPa and total elongation of 70.0% at a strain rate of 10^(-3)s^(-1), overwhelmingly higher than those of the base metal, 155.6 MPa in UTS and 36.0%in elongation. The in-situ SEM-DIC analysis and TEM observation demonstrated that such an outstanding ductility with moderate strength is caused by grain boundary sliding, the dominant deformation mechanism of the ultra-fine-grained sample after FSP. The processing route with reverse processing direction was proven to be efficient in producing the ultrafine grain size microstructure and improving the mechanical properties of superlight Mg-9Li-1Zn alloy.
