The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nit...The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.展开更多
In the study,three 16Cr-25.5Ni-4.2Mo superaustenitic stainless steel weld metals with C contents of 0.082 wt%,0.075 wt%,and 0.045 wt%,were prepared to investigate the microstructural evolution and its effect on mechan...In the study,three 16Cr-25.5Ni-4.2Mo superaustenitic stainless steel weld metals with C contents of 0.082 wt%,0.075 wt%,and 0.045 wt%,were prepared to investigate the microstructural evolution and its effect on mechanical behavior.At a C content of 0.082 wt%,the microstructure of weld metal consisted of austenite,M_(6)C,and M_(23)C_(6),where M_(6)C was the main carbide.The number and average size of the M_(6)C carbides significantly decreased as the C content decreased.At a C content of 0.045 wt%,only a very small number of M_(6)C carbides were observed in the weld metal.For the tensile process,the number of deformation twins increased as the C content decreased,which introduced a stronger dynamic Hall-Petch effect,resulting in only a small decrease in the ultimate tensile strength of the weld metal.Meanwhile,the increase in deformation twins significantly enhanced the elongation of the weld metals.For the impact process,the impact energy increased from 204 to 241 J as the C content decreased.The crack initiation resistance was improved due to the reduction in M_(6)C carbide,which inhibited cracking at the interface of M_(6)C/matrix.Additionally,the crack propagation resistance was enhanced due to the increase in deformation twins,which consumed more impact energy.展开更多
Aqueous zinc metal batteries(ZMBs)are vital to potable electronics and electric energy infrastructures because of their high energy conversion efficiency,high energy density,and environmental friendliness.However,ramp...Aqueous zinc metal batteries(ZMBs)are vital to potable electronics and electric energy infrastructures because of their high energy conversion efficiency,high energy density,and environmental friendliness.However,rampant zinc dendrite growth and side reactions on the Zn anode seriously impede the practical application of ZMBs.In this work,morpholine-crosslinked polyacrylamide hydrogel electrolytes(ploy(acrylamide),6m-PAM)are successfully developed to simultaneously regulate solvation shell to suppress side reactions and homogenize Zn^(2+)ion migration for dendrite-free ZMBs.Notably,the 6m-PAM electrolyte exhibits excellent mechanical strength of 50.6 kPa,high Zn^(2+)ion conductivity of 52 mS cm^(-1)at room temperature,and fast self-healing ability,providing stable and adaptable electrolyte-anode interfaces.Experimental and theoretical calculation results reveal that Zn^(2+)-N(morpholine)coordination interaction effectively reshapes the primary solvation shell of Zn^(2+),suppressing the activity of free water and Zn dendrites.As a result,the 6m-PAM electrolyte endows symmetric zinc cells with a long-term cycling life of 2000 h at 7.5 mA cm^(-2).Notably,Zn/Polyaniline(PANI)batteries equipped with 6m-PAM electrolytes also exhibit a high capacity of 124 mA h g^(-1)at 1 A g^(-1)and a long cycling life of 4000 times with a high-capacity retention of 98.3%,This functional crosslinked hydrogel electrolyte paves a new way to construct durable dendrite-free ZMBs.展开更多
The large and dense rare earth (RE)-oxide inclusions in high-oxygen RE metal increase the risk of producing variable properties in RE steel. Consequently, a self-developed electrolysis cell was utilized for the produc...The large and dense rare earth (RE)-oxide inclusions in high-oxygen RE metal increase the risk of producing variable properties in RE steel. Consequently, a self-developed electrolysis cell was utilized for the production of low-oxygen La/Ce mischmetal. The electrolysis process and the origin of oxygen in mischmetal were comprehensively investigated. The results indicate that the reaction between La/Ce oxide and fluoride molten salt results in the formation of La/Ce oxy-fluoride. The deposition of oxy-fluoride at the bottom of the electrolysis cell is the primary factor contributing to the increased oxygen content in mischmetal. The comprehensive influence of oxide addition quantity, feeding interval, and electrolysis temperature on oxygen content, purity, and current efficiency using the response surface methodology model is revealed. The results for industrial experiment show that the purity of mishcmetal reaches higher than 99.78 wt.%, the oxygen content of mischmetal is only 0.0047 wt.% and the current efficiency of the electrolysis process achieves 80.79% under the optimized parameters of 225 kg/d, 30 s and 1069 ℃. The findings offer valuable insights into the application of molten salt electrolysis for the production of low-oxygen mischmetal.展开更多
Strength and plasticity of metallic structural materials are the fundamental indicators of the service reliability[1].However,as is well known,a general trade-offrelationship exists between strength and plasticity of ...Strength and plasticity of metallic structural materials are the fundamental indicators of the service reliability[1].However,as is well known,a general trade-offrelationship exists between strength and plasticity of metallic materials,making it difficult to improve both of them synchronously[2].At present,only few of the successful cases[3-8],achieved via nano-particles[7],heterogeneous microstructures[8],etc.are mostly limited to some specific materials or processes.展开更多
9Cr ferritic/martensitic(9Cr F/M)steels are considered ideal structural materials for various nuclear energy systems.However,δ-ferrite(δ),as a controlled phase,may occur in its welds.Three deposited metals with diff...9Cr ferritic/martensitic(9Cr F/M)steels are considered ideal structural materials for various nuclear energy systems.However,δ-ferrite(δ),as a controlled phase,may occur in its welds.Three deposited metals with different carbon contents(0.04,0.07,and 0.10 wt%)were investigated using experimental and finite element simulation methods.The results showed that the incomplete peritectic reaction,the incompleteδto austenite phase transition,and the segregation of ferrite-stabilized elements led to the residualδ.The amount and morphology ofδsignificantly influence the mechanical properties.After increasing the carbon content,the increase in strength comes mainly from precipitation strengthening and dislocation strengthening,the presence ofδwill reduce the strength.During the impact process,δaffects the absorbed energy for the stable crack growth through its morphology,and M_(23)C_(6)affects the crack formation energy through its quantity.By decreasing the carbon content to a certain extent,the reduction of M_(23)C_(6)content and the generation of large polygonalδcan effectively improve the toughness of 9Cr-steel deposited metals.展开更多
A corrosion discoloration model for copper-nickel alloys in Cl^(−)environments was established using CIE-Lab,UV-VIS absorption spectroscopy,X-ray diffraction,and X-ray photoelectron spectroscopy.The corrosion discolor...A corrosion discoloration model for copper-nickel alloys in Cl^(−)environments was established using CIE-Lab,UV-VIS absorption spectroscopy,X-ray diffraction,and X-ray photoelectron spectroscopy.The corrosion discoloration process and the corresponding main corrosion products can be summarized as follows:silver-white(Cu+Ni)→green(NiO)→reddishbrown(NiO+Cu_(2)O)→black(NiO+Cu_(2)O+CuO).Density functional theory was employed to explain the corrosion process of copper-nickel alloys and the detrimental effect of Cl^(−).The results indicate that adsorbates preferentially bind to nickel,leading to the preferential formation of NiO,which imparts a green appearance to the surface.Furthermore,the difficulty in forming nickel cation vacancies and the higher diffusion barrier for nickel inhibit the migration of species within the oxide layer.Notably,nickel also suppresses carrier migration within the oxide layer,reducing the charge transfer rate.In contrast,the promotion of corrosion by Cl^(−)is primarily attributed to the reduction in surface work function and the formation energy of cation vacancies.展开更多
Fluorescence-based corrosion detection is an emerging method for surveillance in the early stages of metal corrosion.It is valued for its great responsiveness,non-invasive nature,and capability of in-situ and simultan...Fluorescence-based corrosion detection is an emerging method for surveillance in the early stages of metal corrosion.It is valued for its great responsiveness,non-invasive nature,and capability of in-situ and simultaneous detection.This review paper presents a thorough and up-to-date review of fluorescencebased methods for detecting metal corrosion.It introduces the underlying principles of these detection methods,aligned with the corrosion processes of metals.The paper categorizes fluorescent indicators into those sensitive to pH changes and those responsive to metal ions,both serving as early indicators of corrosion.It also discusses the factors influencing the sensitivity of fluorescence detection and various methods of incorporating fluorescent indicators.Lastly,the paper outlines critical future directions for the betterment of fluorescence-based corrosion diagnosis.展开更多
The demand for lightweight,thin,and broadband microwave absorption materials has been grow-ing rapidly with advancements in microelectronics and aerospace technology.Conventional microwave-absorbing materials often su...The demand for lightweight,thin,and broadband microwave absorption materials has been grow-ing rapidly with advancements in microelectronics and aerospace technology.Conventional microwave-absorbing materials often suffer from poor dispersion and limited electromagnetic attenuation capac-ity.Herein,we report a novel microwave absorption material that integrates ZIF-67-derived metal or-ganic frameworks(MOFs)with hollow graphene foams(GrFs)synthesized via chemical vapor deposition.The hollow GrFs act as resonant cavities in enhancing multiple reflections and conductive loss,while the MOFs optimize impedance matching for highly efficient microwave absorption.The MOF@GrF-filled paraffin composites achieve a minimum reflection loss(RL_(min))of-50.2 dB at a thickness of 1.3 mm and 7.1 wt.%filler loading,with an impressive microwave absorption efficiency of-38.6 dB/mm.This superior performance is attributed to the synergistic interactions between GrFs and MOFs,integrating conductive loss,cavity confinement,dipole polarization,interfacial polarization,magnetic loss,and im-proved impedance matching.This study paves a way for fabricating high-efficiency microwave absorption materials for application in fields of aerospace,medical equipment,and electronic industry.展开更多
Maintaining high metal dispersion of supported metal catalysts to achieve superior reactivity under harsh conditions poses one of the main challenges for their practical applications.Constructing and regulating the st...Maintaining high metal dispersion of supported metal catalysts to achieve superior reactivity under harsh conditions poses one of the main challenges for their practical applications.Constructing and regulating the strong metal-support interactions(SMSI)by diverse methodologies has emerged as one of the promising approaches to fabricating robust supported metal catalysts.In this study,we report an L-ascorbic acid(AA)-inducing strategy to generate SMSI on a titania-supported gold(Au)catalyst after high-temperature treatment in an inert atmosphere(600℃,N_(2)).The AA-induced SMSI can efficiently stabilize Au nanoparticles(NPs)and preserve their catalytic performance.The detailed study reveals that the key to realizing this SMSI is the generation of oxygen vacancies within the TiO_(2) support induced by the adsorbed AA,which drives the formation of the Ti Oxpermeable layer onto the Au NPs.The strategy could be extended to TiO_(2)-supported Au catalysts with different crystal phases and platinum group metals,such as Pt,Pd,and Rh.This work offers a promising novel route to design stable and efficient supported noble metal catalysts by constructing SMSI using simple reducing organic adsorbent.展开更多
Non-metallic inclusions are a significant factor causing fractures during the manufacturing process of tire cord steel,and dissolution in the steel profoundly affects them.How the basicity and Al_(2)O_(3) content in S...Non-metallic inclusions are a significant factor causing fractures during the manufacturing process of tire cord steel,and dissolution in the steel profoundly affects them.How the basicity and Al_(2)O_(3) content in SiO_(2)-CaO-Al_(2)O_(3)-MgO refining slag affect non-metallic inclusions in tire cord steel at 1873 K was investigated.A quantitative relationship has been established between the slag basicity and the dissolved oxygen content in steel.The results demonstrate that non-metallic inclusions in steel transform along SiO_(2)-MnO-Al_(2)O_(3)→SiO_(2)-MnO system of inclusions.When the basicity is controlled within the range of 0.8-1.0,the corresponding dissolved oxygen content should be between 4×10^(−6) and 10×10^(−6).When Al_(2)O_(3) content in the refining slag is maintained at 5%,and the slag basicity is controlled between 0.8 and 1.0,or if the slag basicity is precisely 1.0 with Al_(2)O_(3) content kept below 11%,control over the plasticization of SiO_(2)-MnO-Al_(2)O_(3) system within the inclusions can be effectively achieved.Combined with thermodynamic calculation and measurement of the dissolved oxygen([O])activity in the steel,controlling SiO_(2)-MnO-Al_(2)O_(3)-like inclusions in the plastic region range can be achieved by adjusting the refining slag composition.展开更多
Annealing has been a popular method to improve the soft magnetism of metallic glasses (MGs), which however usually makes MGs brittle and difficult to process. Here, it is demonstrated that the embrittled Fe-based MG c...Annealing has been a popular method to improve the soft magnetism of metallic glasses (MGs), which however usually makes MGs brittle and difficult to process. Here, it is demonstrated that the embrittled Fe-based MG can be reductilized and the coercivity can be further lowered through the rejuvenation of memory effect. The synchronous improvement in the plasticity and soft magnetic properties is attributed to the combination effects of releasing much residual stress, decreasing the magnetic anisotropy, and homogenizing the glasses during the rejuvenation process. The current work opens a new perspective to improve the properties of MGs by utilizing the memory effect and holds promising commercial application potential.展开更多
The influence of Hf on the precipitation behavior of γ'phase and the subsequent tensile properties of a Ni-Cr-Mo alloy after long-term thermal exposure was investigated.The results reveal that the addition of Hf ...The influence of Hf on the precipitation behavior of γ'phase and the subsequent tensile properties of a Ni-Cr-Mo alloy after long-term thermal exposure was investigated.The results reveal that the addition of Hf increases the average diameter ofγ'phases after thermal exposure at 700℃ for 5000 h,which enhances the critical resolved shear stress required for dislocations to shear the γ'phases in the Ni-Cr-Mo alloy.Simultaneously,element Hf incorporated into the γ'phases increases the lattice mismatch between the γ'and γ phase,thereby strengthening the coherency strengthening effect.These two factors collectively contribute to the enhanced strength of the alloy.Thus,Hf alloying effectively improves the yield strength of the Ni-Cr-Mo alloy after thermal exposure at 700℃.展开更多
Carbon fiber-reinforced carbon aerogel(C/CA)composites are one of the most promising candidates for applications requiring both thermal insulation and load bearing capabilities.The preparation of anti-oxidation coatin...Carbon fiber-reinforced carbon aerogel(C/CA)composites are one of the most promising candidates for applications requiring both thermal insulation and load bearing capabilities.The preparation of anti-oxidation coatings on C/CA to address its susceptibility to oxidation is a feasible approach to promote its application in oxidative environments.However,the currently reported coatings on C/CA mainly focus on improving the ablation performance and coating preparation process typically necessitating high-temperature heat treatment.This procedure can increase its thermal conductivity and reduce its thermal insulation ability.In this study,a series of ceramic-resin coatings were fabricated on C/CA through a simple slurry brushing-drying approach at room temperature.The effects of phenolic resin content on the coating structure,residual stress,thermal shock,and oxidation behaviors were investigated.Due to the adhesive properties and curing-induced shrinkage,the PR-7.5 coating(containing 7.5%(in mass)phenolic resin in the slurry)exhibits bonding strength close to fracture strength of the substrate and residual compressive stress of 0.853 GPa,which is beneficial for resisting thermal shock cracking.However,excessive resin content(PR-10.0 containing 10.0%(in mass)phenolic resin in the slurry)induces tensile stress due to uneven curing shrinkage,thereby leading to thermal shock cracking.Meanwhile,oxidation tests reveal significantly reduced weight losses for PR-7.5(17.46%at 800℃/100 min,8.15%at 1000℃/120 min,3.15%at 1200℃/120 min)versus uncoated C/CA’s 44.60%loss at 800℃/20 min.This work provides a brand-new and simple approach to improving the anti-oxidation performance of C/CA and expands its application in mild oxidative environments.展开更多
Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed...Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed.For all of water,oil,air and furnace cooling,there is almost-complete martensite with the favorable hardenability.The increase in cooling rate mainly increases the density of dislocation and residual strain in the as-solution annealed matrix.After aging treatment,the cooling rate dominates the ratio of high-angle grain boundaries(HAGBs)instead of the size of martensite blocks.The ratio of HAGBs continuously increases with the decreased cooling rate,while the width of blocks maintains 2.40-2.49μm.Meanwhile,more reversed austenite distributes at the martensite sub-grain boundaries.By comparison,the increased rate of water cooling contributes to a favorable precipitation of NiAl with fine size and dispersive distribution caused by more accumulated internal defects of vacancies and dislocations.With the decrease of cooling rate,NiAl precipitates exhibits a similar diameter of~7 nm while a larger inter-particle distance of~22 nm.In the case of low cooling rate(oil,air and furnace),the stable precipitation strengthening effect contributes to a high yield strength of~1.3 GPa and ultimate tensile strength of~1.4 GPa.The high-ratio HAGBs,reversed austenite and NiAl precipitates with larger-interparticle distance synergistically improve the impact toughness(V-notched Charpy impact energy of 100-110 J).展开更多
Turbine blades,due to their intricate geometry,are exposed to multiaxial stresses during operation.Consequently,it is imperative to examine the anisotropy of their stress-rupture behavior across various testing scenar...Turbine blades,due to their intricate geometry,are exposed to multiaxial stresses during operation.Consequently,it is imperative to examine the anisotropy of their stress-rupture behavior across various testing scenarios,particularly under high-temperature conditions.Stress-rupture behavior of a Ni-based single crystal superalloy was investigated under a load varying from 100 MPa to 137 MPa at 1,100℃ for both[001]-and[111]-orientated specimens.Results demonstrate that the rupture behavior of[111]-orientated specimens exhibits obviously higher sensitive to applied stress compared to[001]-orientated specimens.This difference is primarily attributed to the orientation dependentγ'coarsening behavior and distinct dislocation interactions atγ/γ'interfaces.In[001]-oriented specimens,plate-likeγ/γ'rafts rapidly form alongside well-developed interfacial dislocation networks,where theγ/γ'misfit stress dominates the microstructural evolution.In contrast,the[111]-orientated specimens exhibit retained,coarsenedγ'precipitates embedded within theγmatrix,accompanied by poorly developed interfacial dislocation networks.展开更多
The high-alloyed wrought superalloy GH4975 tends to form coarse MC carbides and eutectic(γ+γ′)phases,which adversely affect the cogging and homogenization process.To provide theoretical guidance for control of MC c...The high-alloyed wrought superalloy GH4975 tends to form coarse MC carbides and eutectic(γ+γ′)phases,which adversely affect the cogging and homogenization process.To provide theoretical guidance for control of MC carbides and eutectic(γ+γ′)formation,differential thermal analysis(DTA)was utilized to investigate the effect of cooing rate(10-90℃·min^(-1))on solidification behavior and micro-segregation of GH4975 alloy.According to the thermodynamic calculation and distribution characteristics of precipitates,the MC carbides can act as nucleation sites forγdendrites,but the nucleation ofγdendrites becomes less dependent on the MC carbide primers at higher cooling rates.As theγdendrites grow,the elements including Ti and Nb gradually accumulate in the residual liquid and leads to the formation of more MC carbides near the interdendritic region.Finally,the solidification is terminated with the formation of eutectic(γ+γ′).With an increase in cooling rate,the liquidus temperature rises,but the solidus temperature decreases,and thus the solidification range is obviously enlarged.The dendritic structure is significantly refined by the increase of cooling rate.The secondary dendrite arm spacing,λ_(2),as a function of cooling rate,T,can be expressed asλ_(2)=216.78T^(-0.42).Moreover,the increasing cooling rate weakens the back diffusion of Al,Ti,and Nb,increases the undercooling,and limits the growth of precipitates.Consequently,the sizes of MC carbides,eutectic(γ+γ′),and primaryγ′significantly decrease,but the area fraction of eutectic(γ+γ′)linerly increases as the cooling rate rises.Thus moderate cooling rate(such as 30℃·min^(-1))should be selected during the solidification process of GH4975 alloy.展开更多
Metal-support interaction(MSI) is crucial for fine-tuning the active-site structure of supported catalysts and enhancing performance.Here,we present an ammonia-directed reactive gas-metal-support interaction(RGMSI),in...Metal-support interaction(MSI) is crucial for fine-tuning the active-site structure of supported catalysts and enhancing performance.Here,we present an ammonia-directed reactive gas-metal-support interaction(RGMSI),in which NH_(3) reduces ZnO and assembles an anti-perovskite Ni_(3)ZnN structure with interstitial nitrogen,significantly boosting hydrogenation efficiency.Nitrogen incorporation expands the lattice parameter,increasing the(111) lattice spacing from 2.04Å in Ni to 2.18Å in Ni_(3)ZnN,with an extended Ni-Ni interatomic distance from 2.49Å to 2.65Å.Additionally,Ni-N coordination shifts the d-band center downward and induces electron deficiency in Ni via charge transfer.These modifications optimize reactant adsorption on the tailored Ni_(3)ZnN structure compared to Ni,leading to a remarkable increase in 1,3-butadiene hydrogenation selectivity from 30.0 % to 92.9 %,along with an enhanced TOF from 0.067 s^(-1) to 0.079 s^(-1).These findings highlight RGMSI as a versatile and effective strategy for designing supported metal catalysts,offering new insights into selective hydrogenation catalysis.展开更多
Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles a...Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles appeared at the bottom of the part during single-step forming,but no wrinkles were observed during double-step forming.The thinning rate and deviation of the wall thickness of the part in each area were less than 20%and 2.7 mm,correspondingly,and the drawing depth of the part reached 45.8 mm.The effect of double-step forming was better than that of single-step forming,which was related to the IHF forming law.Besides,the characteristics of the IHF process were studied by numerical simulation.The results indicated that when double-step forming was utilized,there was almost no velocity field in the opposite direction of deformation after the bottom of the part contacted the die,and the existence of stress state at the bottom would restrain and eliminate the wrinkles.The inertia effect evolved with the driving pressure.Specially,the inertia effect can improve the flow of metal and reduce the deviation of the wall thickness of the part under double-step forming.展开更多
The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD9...The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD98M alloy significantly decreases with an increase in impurity content,and the presence of nitrogen leads to an increase in alloy porosity.These porosities promote the rapid diffusion of molten salt and oxygen into the alloy,resulting in a bilateral diffusion of oxygen and sulfur,which leads to an accumulation of these elements at the oxide−matrix interface.This process contributes to the formation and propagation of interfacial cracks.A growth model was developed for hot corrosion products in alloys with varying impurity elements.展开更多
基金partially supported by National Natural Science Foundation of China(52172250)Institute of Process Engineering(IPE)Project for Frontier Basic Research(QYJC-2023-06)。
文摘The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.
基金supported by the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDA0410201)the Natural Science Foundation of Heilongjiang Province(No.TD2021E006)+1 种基金the Liaoning Provincial Doctoral Initiation Fund Project(No.2022-BS-008)the China Postdoctoral Science Foundation(No.2023T160654).
文摘In the study,three 16Cr-25.5Ni-4.2Mo superaustenitic stainless steel weld metals with C contents of 0.082 wt%,0.075 wt%,and 0.045 wt%,were prepared to investigate the microstructural evolution and its effect on mechanical behavior.At a C content of 0.082 wt%,the microstructure of weld metal consisted of austenite,M_(6)C,and M_(23)C_(6),where M_(6)C was the main carbide.The number and average size of the M_(6)C carbides significantly decreased as the C content decreased.At a C content of 0.045 wt%,only a very small number of M_(6)C carbides were observed in the weld metal.For the tensile process,the number of deformation twins increased as the C content decreased,which introduced a stronger dynamic Hall-Petch effect,resulting in only a small decrease in the ultimate tensile strength of the weld metal.Meanwhile,the increase in deformation twins significantly enhanced the elongation of the weld metals.For the impact process,the impact energy increased from 204 to 241 J as the C content decreased.The crack initiation resistance was improved due to the reduction in M_(6)C carbide,which inhibited cracking at the interface of M_(6)C/matrix.Additionally,the crack propagation resistance was enhanced due to the increase in deformation twins,which consumed more impact energy.
基金supported by the National Natural Science Foundation of China(22479022)the Natural Science Foundation of Liaoning Province(2020-MS-021)。
文摘Aqueous zinc metal batteries(ZMBs)are vital to potable electronics and electric energy infrastructures because of their high energy conversion efficiency,high energy density,and environmental friendliness.However,rampant zinc dendrite growth and side reactions on the Zn anode seriously impede the practical application of ZMBs.In this work,morpholine-crosslinked polyacrylamide hydrogel electrolytes(ploy(acrylamide),6m-PAM)are successfully developed to simultaneously regulate solvation shell to suppress side reactions and homogenize Zn^(2+)ion migration for dendrite-free ZMBs.Notably,the 6m-PAM electrolyte exhibits excellent mechanical strength of 50.6 kPa,high Zn^(2+)ion conductivity of 52 mS cm^(-1)at room temperature,and fast self-healing ability,providing stable and adaptable electrolyte-anode interfaces.Experimental and theoretical calculation results reveal that Zn^(2+)-N(morpholine)coordination interaction effectively reshapes the primary solvation shell of Zn^(2+),suppressing the activity of free water and Zn dendrites.As a result,the 6m-PAM electrolyte endows symmetric zinc cells with a long-term cycling life of 2000 h at 7.5 mA cm^(-2).Notably,Zn/Polyaniline(PANI)batteries equipped with 6m-PAM electrolytes also exhibit a high capacity of 124 mA h g^(-1)at 1 A g^(-1)and a long cycling life of 4000 times with a high-capacity retention of 98.3%,This functional crosslinked hydrogel electrolyte paves a new way to construct durable dendrite-free ZMBs.
基金supported by the National Natural Science Foundation of China(No.52101165)the Inner Mongolia Science and Technology Major Project(No.2020ZD0010)the Key Research Program of the Chinese Academy of Sciences(No.ZDRW-CN-2021-3).
文摘The large and dense rare earth (RE)-oxide inclusions in high-oxygen RE metal increase the risk of producing variable properties in RE steel. Consequently, a self-developed electrolysis cell was utilized for the production of low-oxygen La/Ce mischmetal. The electrolysis process and the origin of oxygen in mischmetal were comprehensively investigated. The results indicate that the reaction between La/Ce oxide and fluoride molten salt results in the formation of La/Ce oxy-fluoride. The deposition of oxy-fluoride at the bottom of the electrolysis cell is the primary factor contributing to the increased oxygen content in mischmetal. The comprehensive influence of oxide addition quantity, feeding interval, and electrolysis temperature on oxygen content, purity, and current efficiency using the response surface methodology model is revealed. The results for industrial experiment show that the purity of mishcmetal reaches higher than 99.78 wt.%, the oxygen content of mischmetal is only 0.0047 wt.% and the current efficiency of the electrolysis process achieves 80.79% under the optimized parameters of 225 kg/d, 30 s and 1069 ℃. The findings offer valuable insights into the application of molten salt electrolysis for the production of low-oxygen mischmetal.
基金financially supported by the National Natural Science Foundation of China(NSFC)(Nos.52371084,52301177,52322105,52130002,and 52321001)the Youth Innovation Promotion Association CAS(No.2021192)+1 种基金the IMR Innovation Fund(No.2023-ZD01)the Fund of Science and Technology on Surface Physics and Chemistry Laboratory(No.XKFZ202303).
文摘Strength and plasticity of metallic structural materials are the fundamental indicators of the service reliability[1].However,as is well known,a general trade-offrelationship exists between strength and plasticity of metallic materials,making it difficult to improve both of them synchronously[2].At present,only few of the successful cases[3-8],achieved via nano-particles[7],heterogeneous microstructures[8],etc.are mostly limited to some specific materials or processes.
基金supported by the LingChuang Research Project of China National Nuclear Corporation,China Institute of Atomic Energy(E141L803J1)the Natural Science Foundation of Heilongjiang Province(No.TD2021E006).
文摘9Cr ferritic/martensitic(9Cr F/M)steels are considered ideal structural materials for various nuclear energy systems.However,δ-ferrite(δ),as a controlled phase,may occur in its welds.Three deposited metals with different carbon contents(0.04,0.07,and 0.10 wt%)were investigated using experimental and finite element simulation methods.The results showed that the incomplete peritectic reaction,the incompleteδto austenite phase transition,and the segregation of ferrite-stabilized elements led to the residualδ.The amount and morphology ofδsignificantly influence the mechanical properties.After increasing the carbon content,the increase in strength comes mainly from precipitation strengthening and dislocation strengthening,the presence ofδwill reduce the strength.During the impact process,δaffects the absorbed energy for the stable crack growth through its morphology,and M_(23)C_(6)affects the crack formation energy through its quantity.By decreasing the carbon content to a certain extent,the reduction of M_(23)C_(6)content and the generation of large polygonalδcan effectively improve the toughness of 9Cr-steel deposited metals.
基金supported by the Key Program of the National Natural Science Foundation of China(Grant No.51131007)the National Key Research and Development Program of China(Grant No.2021YFC2803102).
文摘A corrosion discoloration model for copper-nickel alloys in Cl^(−)environments was established using CIE-Lab,UV-VIS absorption spectroscopy,X-ray diffraction,and X-ray photoelectron spectroscopy.The corrosion discoloration process and the corresponding main corrosion products can be summarized as follows:silver-white(Cu+Ni)→green(NiO)→reddishbrown(NiO+Cu_(2)O)→black(NiO+Cu_(2)O+CuO).Density functional theory was employed to explain the corrosion process of copper-nickel alloys and the detrimental effect of Cl^(−).The results indicate that adsorbates preferentially bind to nickel,leading to the preferential formation of NiO,which imparts a green appearance to the surface.Furthermore,the difficulty in forming nickel cation vacancies and the higher diffusion barrier for nickel inhibit the migration of species within the oxide layer.Notably,nickel also suppresses carrier migration within the oxide layer,reducing the charge transfer rate.In contrast,the promotion of corrosion by Cl^(−)is primarily attributed to the reduction in surface work function and the formation energy of cation vacancies.
基金financially supported by the National Natural Science Foundation of China(Nos.52171089 and 51571202)the Liaoning Province International Science and Technology Coopera-tion Program Project(No.2024JH2/101900013)+1 种基金the Key Program of Basic Research Projects of Liaoning Provincial Department of Edu-cation(No.JYTZD2023114)the LingChuang Research Project of China National Nuclear Corporation(No.E041F212Z1).
文摘Fluorescence-based corrosion detection is an emerging method for surveillance in the early stages of metal corrosion.It is valued for its great responsiveness,non-invasive nature,and capability of in-situ and simultaneous detection.This review paper presents a thorough and up-to-date review of fluorescencebased methods for detecting metal corrosion.It introduces the underlying principles of these detection methods,aligned with the corrosion processes of metals.The paper categorizes fluorescent indicators into those sensitive to pH changes and those responsive to metal ions,both serving as early indicators of corrosion.It also discusses the factors influencing the sensitivity of fluorescence detection and various methods of incorporating fluorescent indicators.Lastly,the paper outlines critical future directions for the betterment of fluorescence-based corrosion diagnosis.
基金supported by the National Natural Science Foundation of China(Nos.52472056 and 52130209)the Science and Technology Program of Liaoning Province,China(No.2023JH26/10300015)+1 种基金the Natural Science Foundation of Liaoning Province,China(No.2022-KF-12-04)the Opening Foundation of Shanxi Key Laboratory of Nano&Functional Composite Materi-als(No.NFCM202102).
文摘The demand for lightweight,thin,and broadband microwave absorption materials has been grow-ing rapidly with advancements in microelectronics and aerospace technology.Conventional microwave-absorbing materials often suffer from poor dispersion and limited electromagnetic attenuation capac-ity.Herein,we report a novel microwave absorption material that integrates ZIF-67-derived metal or-ganic frameworks(MOFs)with hollow graphene foams(GrFs)synthesized via chemical vapor deposition.The hollow GrFs act as resonant cavities in enhancing multiple reflections and conductive loss,while the MOFs optimize impedance matching for highly efficient microwave absorption.The MOF@GrF-filled paraffin composites achieve a minimum reflection loss(RL_(min))of-50.2 dB at a thickness of 1.3 mm and 7.1 wt.%filler loading,with an impressive microwave absorption efficiency of-38.6 dB/mm.This superior performance is attributed to the synergistic interactions between GrFs and MOFs,integrating conductive loss,cavity confinement,dipole polarization,interfacial polarization,magnetic loss,and im-proved impedance matching.This study paves a way for fabricating high-efficiency microwave absorption materials for application in fields of aerospace,medical equipment,and electronic industry.
基金supported by the National Natural Science Foundation of China(NSFC)the Japan Society for the Promotion of Science(JSPS)under the Joint Research Program(Nos.NSFC21961142006 and JPJSJRP20191804)+3 种基金NSFC(Nos.U22A20394 and 22375200)the DICP.CAS-Cardiff Joint Research Units(No.121421ZYLH20230008)the International Partnership Program of Chinese Academy of Sciences(No.028GJHZ2023097GC)the China Postdoctoral Science Foundation(No.2022M723086)。
文摘Maintaining high metal dispersion of supported metal catalysts to achieve superior reactivity under harsh conditions poses one of the main challenges for their practical applications.Constructing and regulating the strong metal-support interactions(SMSI)by diverse methodologies has emerged as one of the promising approaches to fabricating robust supported metal catalysts.In this study,we report an L-ascorbic acid(AA)-inducing strategy to generate SMSI on a titania-supported gold(Au)catalyst after high-temperature treatment in an inert atmosphere(600℃,N_(2)).The AA-induced SMSI can efficiently stabilize Au nanoparticles(NPs)and preserve their catalytic performance.The detailed study reveals that the key to realizing this SMSI is the generation of oxygen vacancies within the TiO_(2) support induced by the adsorbed AA,which drives the formation of the Ti Oxpermeable layer onto the Au NPs.The strategy could be extended to TiO_(2)-supported Au catalysts with different crystal phases and platinum group metals,such as Pt,Pd,and Rh.This work offers a promising novel route to design stable and efficient supported noble metal catalysts by constructing SMSI using simple reducing organic adsorbent.
基金supported by the National Natural Science Foundation of China(Nos.52274337,52174317 and U1960203)2023 Liaoning Province Department of Education Fundamental Research Project Achievements(No.JYTMS20230928).
文摘Non-metallic inclusions are a significant factor causing fractures during the manufacturing process of tire cord steel,and dissolution in the steel profoundly affects them.How the basicity and Al_(2)O_(3) content in SiO_(2)-CaO-Al_(2)O_(3)-MgO refining slag affect non-metallic inclusions in tire cord steel at 1873 K was investigated.A quantitative relationship has been established between the slag basicity and the dissolved oxygen content in steel.The results demonstrate that non-metallic inclusions in steel transform along SiO_(2)-MnO-Al_(2)O_(3)→SiO_(2)-MnO system of inclusions.When the basicity is controlled within the range of 0.8-1.0,the corresponding dissolved oxygen content should be between 4×10^(−6) and 10×10^(−6).When Al_(2)O_(3) content in the refining slag is maintained at 5%,and the slag basicity is controlled between 0.8 and 1.0,or if the slag basicity is precisely 1.0 with Al_(2)O_(3) content kept below 11%,control over the plasticization of SiO_(2)-MnO-Al_(2)O_(3) system within the inclusions can be effectively achieved.Combined with thermodynamic calculation and measurement of the dissolved oxygen([O])activity in the steel,controlling SiO_(2)-MnO-Al_(2)O_(3)-like inclusions in the plastic region range can be achieved by adjusting the refining slag composition.
基金support from the National Natural Science Foundation of China(No.52231006)Junqiang Wang acknowledges financial support from the National Key R&D Program of China(No.2018YFA0703600)the National Natural Science Foundation of China(Nos.92163108 and 52222105).
文摘Annealing has been a popular method to improve the soft magnetism of metallic glasses (MGs), which however usually makes MGs brittle and difficult to process. Here, it is demonstrated that the embrittled Fe-based MG can be reductilized and the coercivity can be further lowered through the rejuvenation of memory effect. The synchronous improvement in the plasticity and soft magnetic properties is attributed to the combination effects of releasing much residual stress, decreasing the magnetic anisotropy, and homogenizing the glasses during the rejuvenation process. The current work opens a new perspective to improve the properties of MGs by utilizing the memory effect and holds promising commercial application potential.
基金National Key Research and Development Program of China(2021YFB3704103)National Natural Science Foundation of China(51571191)。
文摘The influence of Hf on the precipitation behavior of γ'phase and the subsequent tensile properties of a Ni-Cr-Mo alloy after long-term thermal exposure was investigated.The results reveal that the addition of Hf increases the average diameter ofγ'phases after thermal exposure at 700℃ for 5000 h,which enhances the critical resolved shear stress required for dislocations to shear the γ'phases in the Ni-Cr-Mo alloy.Simultaneously,element Hf incorporated into the γ'phases increases the lattice mismatch between the γ'and γ phase,thereby strengthening the coherency strengthening effect.These two factors collectively contribute to the enhanced strength of the alloy.Thus,Hf alloying effectively improves the yield strength of the Ni-Cr-Mo alloy after thermal exposure at 700℃.
基金National Natural Science Foundation of China(52272075,52472053)Research Fund of Youth Innovation Promotion Association of CAS,China(2021190)Defense Industrial Technology Development Program(JCKY2021130B007)。
文摘Carbon fiber-reinforced carbon aerogel(C/CA)composites are one of the most promising candidates for applications requiring both thermal insulation and load bearing capabilities.The preparation of anti-oxidation coatings on C/CA to address its susceptibility to oxidation is a feasible approach to promote its application in oxidative environments.However,the currently reported coatings on C/CA mainly focus on improving the ablation performance and coating preparation process typically necessitating high-temperature heat treatment.This procedure can increase its thermal conductivity and reduce its thermal insulation ability.In this study,a series of ceramic-resin coatings were fabricated on C/CA through a simple slurry brushing-drying approach at room temperature.The effects of phenolic resin content on the coating structure,residual stress,thermal shock,and oxidation behaviors were investigated.Due to the adhesive properties and curing-induced shrinkage,the PR-7.5 coating(containing 7.5%(in mass)phenolic resin in the slurry)exhibits bonding strength close to fracture strength of the substrate and residual compressive stress of 0.853 GPa,which is beneficial for resisting thermal shock cracking.However,excessive resin content(PR-10.0 containing 10.0%(in mass)phenolic resin in the slurry)induces tensile stress due to uneven curing shrinkage,thereby leading to thermal shock cracking.Meanwhile,oxidation tests reveal significantly reduced weight losses for PR-7.5(17.46%at 800℃/100 min,8.15%at 1000℃/120 min,3.15%at 1200℃/120 min)versus uncoated C/CA’s 44.60%loss at 800℃/20 min.This work provides a brand-new and simple approach to improving the anti-oxidation performance of C/CA and expands its application in mild oxidative environments.
基金supported by the National Key Research and Development Program(Grant No.2024YFB3714200)the National Natural Science Foundation of China(Grant Nos.52173305,52233017,52203384,U244120568 and U2441261)+1 种基金the Key Program of the Chinese Academy of Sciences(Grant No.RCJJ-145-24-40)LingChuang Research Project of China National Nuclear Corporation,and Special Funds for Science and Technology Planning of Jiangsu Province(No.BZ2024059).
文摘Different from previous attention on the austenization temperature or dwelling time of PH13-8Mo stainless steels,the effect of the cooling rate on the hierarchical microstructure and mechanical properties was revealed.For all of water,oil,air and furnace cooling,there is almost-complete martensite with the favorable hardenability.The increase in cooling rate mainly increases the density of dislocation and residual strain in the as-solution annealed matrix.After aging treatment,the cooling rate dominates the ratio of high-angle grain boundaries(HAGBs)instead of the size of martensite blocks.The ratio of HAGBs continuously increases with the decreased cooling rate,while the width of blocks maintains 2.40-2.49μm.Meanwhile,more reversed austenite distributes at the martensite sub-grain boundaries.By comparison,the increased rate of water cooling contributes to a favorable precipitation of NiAl with fine size and dispersive distribution caused by more accumulated internal defects of vacancies and dislocations.With the decrease of cooling rate,NiAl precipitates exhibits a similar diameter of~7 nm while a larger inter-particle distance of~22 nm.In the case of low cooling rate(oil,air and furnace),the stable precipitation strengthening effect contributes to a high yield strength of~1.3 GPa and ultimate tensile strength of~1.4 GPa.The high-ratio HAGBs,reversed austenite and NiAl precipitates with larger-interparticle distance synergistically improve the impact toughness(V-notched Charpy impact energy of 100-110 J).
基金financially supported by the National Science and Technology Major Project of China(No.2019-VII-0019-0161 and No.2019-VII-0004-0144)the National Natural Science Foundation of China(No.92360302)the Shandong Provincial Natural Science Foundation of China(No.ZR2021QE103)。
文摘Turbine blades,due to their intricate geometry,are exposed to multiaxial stresses during operation.Consequently,it is imperative to examine the anisotropy of their stress-rupture behavior across various testing scenarios,particularly under high-temperature conditions.Stress-rupture behavior of a Ni-based single crystal superalloy was investigated under a load varying from 100 MPa to 137 MPa at 1,100℃ for both[001]-and[111]-orientated specimens.Results demonstrate that the rupture behavior of[111]-orientated specimens exhibits obviously higher sensitive to applied stress compared to[001]-orientated specimens.This difference is primarily attributed to the orientation dependentγ'coarsening behavior and distinct dislocation interactions atγ/γ'interfaces.In[001]-oriented specimens,plate-likeγ/γ'rafts rapidly form alongside well-developed interfacial dislocation networks,where theγ/γ'misfit stress dominates the microstructural evolution.In contrast,the[111]-orientated specimens exhibit retained,coarsenedγ'precipitates embedded within theγmatrix,accompanied by poorly developed interfacial dislocation networks.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52474362,52174317 and 51904146)the General Project Funded by Liaoning Province Education Department(Grant No.JYTMS20230943)。
文摘The high-alloyed wrought superalloy GH4975 tends to form coarse MC carbides and eutectic(γ+γ′)phases,which adversely affect the cogging and homogenization process.To provide theoretical guidance for control of MC carbides and eutectic(γ+γ′)formation,differential thermal analysis(DTA)was utilized to investigate the effect of cooing rate(10-90℃·min^(-1))on solidification behavior and micro-segregation of GH4975 alloy.According to the thermodynamic calculation and distribution characteristics of precipitates,the MC carbides can act as nucleation sites forγdendrites,but the nucleation ofγdendrites becomes less dependent on the MC carbide primers at higher cooling rates.As theγdendrites grow,the elements including Ti and Nb gradually accumulate in the residual liquid and leads to the formation of more MC carbides near the interdendritic region.Finally,the solidification is terminated with the formation of eutectic(γ+γ′).With an increase in cooling rate,the liquidus temperature rises,but the solidus temperature decreases,and thus the solidification range is obviously enlarged.The dendritic structure is significantly refined by the increase of cooling rate.The secondary dendrite arm spacing,λ_(2),as a function of cooling rate,T,can be expressed asλ_(2)=216.78T^(-0.42).Moreover,the increasing cooling rate weakens the back diffusion of Al,Ti,and Nb,increases the undercooling,and limits the growth of precipitates.Consequently,the sizes of MC carbides,eutectic(γ+γ′),and primaryγ′significantly decrease,but the area fraction of eutectic(γ+γ′)linerly increases as the cooling rate rises.Thus moderate cooling rate(such as 30℃·min^(-1))should be selected during the solidification process of GH4975 alloy.
基金the financial support provided by the National Natural Science Foundation of China (Nos.22072164,22472180,22002173)Energy Revolution S&T Program of Yulin Innovation Institute of Clean Energy (No.E411030705)+2 种基金Natural Science Foundation of Liaoning Province (No.2022-MS004)China Postdoctoral Science Foundation (No.2020M680999)the Research Fund of Shenyang National Laboratory for Materials Science。
文摘Metal-support interaction(MSI) is crucial for fine-tuning the active-site structure of supported catalysts and enhancing performance.Here,we present an ammonia-directed reactive gas-metal-support interaction(RGMSI),in which NH_(3) reduces ZnO and assembles an anti-perovskite Ni_(3)ZnN structure with interstitial nitrogen,significantly boosting hydrogenation efficiency.Nitrogen incorporation expands the lattice parameter,increasing the(111) lattice spacing from 2.04Å in Ni to 2.18Å in Ni_(3)ZnN,with an extended Ni-Ni interatomic distance from 2.49Å to 2.65Å.Additionally,Ni-N coordination shifts the d-band center downward and induces electron deficiency in Ni via charge transfer.These modifications optimize reactant adsorption on the tailored Ni_(3)ZnN structure compared to Ni,leading to a remarkable increase in 1,3-butadiene hydrogenation selectivity from 30.0 % to 92.9 %,along with an enhanced TOF from 0.067 s^(-1) to 0.079 s^(-1).These findings highlight RGMSI as a versatile and effective strategy for designing supported metal catalysts,offering new insights into selective hydrogenation catalysis.
基金financially supported by the National Key R&D Program of China(No.2024YFE0108800/T24KITG014)the National Natural Science Foundation of China(No:52475411)the International Partnership Program of Chinese Academy of Sciences(No.172GJHZ2022096FN)。
文摘Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles appeared at the bottom of the part during single-step forming,but no wrinkles were observed during double-step forming.The thinning rate and deviation of the wall thickness of the part in each area were less than 20%and 2.7 mm,correspondingly,and the drawing depth of the part reached 45.8 mm.The effect of double-step forming was better than that of single-step forming,which was related to the IHF forming law.Besides,the characteristics of the IHF process were studied by numerical simulation.The results indicated that when double-step forming was utilized,there was almost no velocity field in the opposite direction of deformation after the bottom of the part contacted the die,and the existence of stress state at the bottom would restrain and eliminate the wrinkles.The inertia effect evolved with the driving pressure.Specially,the inertia effect can improve the flow of metal and reduce the deviation of the wall thickness of the part under double-step forming.
基金financial support from the National Key Research and Development Project of China(No.2019YFA0705300)the National Natural Science Foundation of China(No.52004051)+1 种基金the Project of Zhongyuan Critical Metals Laboratory,China(No.GJJSGFYQ202321)the Fund for Priority Support of Research Projects by Returned Overseas Scholars in Henan Province,China。
文摘The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD98M alloy significantly decreases with an increase in impurity content,and the presence of nitrogen leads to an increase in alloy porosity.These porosities promote the rapid diffusion of molten salt and oxygen into the alloy,resulting in a bilateral diffusion of oxygen and sulfur,which leads to an accumulation of these elements at the oxide−matrix interface.This process contributes to the formation and propagation of interfacial cracks.A growth model was developed for hot corrosion products in alloys with varying impurity elements.
