Spherical Ni(OH)2 powder coated with Co(OH)2 as raw material was mixed with LiOH to synthesize cathode material for lithium ion battery by using solid-state reaction. After sintered at temperature above 600 ℃, a soli...Spherical Ni(OH)2 powder coated with Co(OH)2 as raw material was mixed with LiOH to synthesize cathode material for lithium ion battery by using solid-state reaction. After sintered at temperature above 600 ℃, a solid solution with layer structure was formed. The result of XPS shows that it is a concentration gradient material with higher cobalt content at the surface, and the gradient decreases with increasing sintering temperature from 650 to 750 ℃. This new gradient material, called as Co-coated LiNiO2, exhibits excellent electrochemical performances for the cathode of Li-ion batteries in comparison with LiNiO2 and Co-doping LiNiO2. The discharge capacity of Co-coated LiNiO2 is over 180 mA·h/g and capacity decay per cycle is less than 0.07% when Co-coated LiNiO2 consisting of 92% nickel and 8% cobalt was sintered at the temperatures between 650-670 ℃. Though initial discharge capacity could be increased with higher sintering temperature, the cycle life would be reduced.展开更多
The development of alternative wood composites based on the use of waste or recycled materials can be beneficial due to over exploitation of natural resources.Under this frame,an option for the successful utilization ...The development of alternative wood composites based on the use of waste or recycled materials can be beneficial due to over exploitation of natural resources.Under this frame,an option for the successful utilization of waste polystyrene which avoids environmental problems that formaldehyde adhesives cause and also reduces waste dis-posal,is its potential application as a binder for the production of value-added environmentally friendly and low cost wood composites.Two types of panel were successfully made,consisting of wood dust and two recycled poly-styrene contents,namely,15%and 30%.Both physical properties,water absorption and thickness swelling,and mechanical properties,modulus of rupture,shear strength parallel in the plane of the board and glue line shear strength,were significantly improved as the recycled polystyrene content increased from 15%to 30%.Water absorption and thickness swelling after 24 h immersion in water were improved by 165%and 750%as the recycled polystyrene content increased from 15%to 30%.The magnitude of the improvement in mechanical properties however,was less pronounced than of the physical properties since modulus of rupture,shear strength parallel in the plane of the board and glue line shear strength were increased by 43.6%,50%and 61.5%,respec-tively.The low viscosity of the recycled polystyrene caused more mobility inside the panel matrix and therefore,an improved penetration took place into adequate depth of the compressed dust particles.It is concluded that boards can be successfully produced using these waste raw materials,wood dust and recycled polystyrene in organic solvent as a binder,and therefore it can reduce waste disposal and provide cleaner production for the development of wood-based boards.展开更多
The demand of higher energy density and higher power capacity of lithium（Li）-ion secondary batteries has led to the search for electrode materials whose capacities and performance are better than those available tod...The demand of higher energy density and higher power capacity of lithium（Li）-ion secondary batteries has led to the search for electrode materials whose capacities and performance are better than those available today. Carbon nanotubes（CNTs）, with their unique properties such as 1D tubular structure, high electrical and thermal conductivities, and extremely large surface area, have been used as materials to prepare cathodes for Li-ion batteries. The structure and morphology of CNTs were analyzed by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, and transmission electron microscopy（TEM）. The functional groups on the purified CNT surface such as –COOH, –OH were characterized by Fourier Transform infrared spectroscopy. The electrode materials were fabricated from LiMn2O4（LMO）, doped spinel LiNi0.5Mn1.5O4, and purified CNTs via solid-state reaction. The structure and morphology of the electrode were characterized using XRD, SEM, and TEM. Finally, the efficiency of the electrode materials using CNTs was evaluated by cyclic voltammetry and electrochemical impedance spectroscopy.展开更多
The article investigated the influence of modification process parameters on dispersity of MWNTs DI （in deionized） water and PVA/MWNT composite＇s electrical conductivity. Experimental results obtained by SEM （scan...The article investigated the influence of modification process parameters on dispersity of MWNTs DI （in deionized） water and PVA/MWNT composite＇s electrical conductivity. Experimental results obtained by SEM （scanning electron microscope）, TEM （transmission electron microscope）, transform Fourier infrared spectroscopy, pH meter confirmed the most effective conditions in modifying the MWNT surface at the 1：3 mixture of nitric and sulfuric acid at 60 ℃. The extinction coefficient value of functionalized MWNTs at 500 nm wavelength was determined to be 41.24 cm^2·mg^-1, while their dispersibility in DI water was about 12.85 mg/mL and stable in more than 3 weeks via UV-vis spectroscopy. The other important result is the decrease of volume resistivity from 7.98 × 10^6 MΩ·m ofPVA （polyvinyl alcohol） to 4.15 × 10^4 MΩ·m of PVA/1 wt% modified MWNT thin film.展开更多
In this research, a highly conductive graphene film was synthesized through the chemical reduction of graphene oxide (RGO) nanosheets followed by thermal treatment at 1100℃ (RGO-1100℃) under H2 ambient. The as-prepa...In this research, a highly conductive graphene film was synthesized through the chemical reduction of graphene oxide (RGO) nanosheets followed by thermal treatment at 1100℃ (RGO-1100℃) under H2 ambient. The as-prepared graphene films were characterized by using X-ray photoelectron spectroscopy, fourier transform infrared spectroscopy, X-ray diffractions, raman spectroscopy, transmission electron microscopy, scanning electron microscopy, atomic force microscopy and by electrical conductivity measurements. The results showed that the thermal treatment efficiently removed residual oxygen-containing functional groups on the surface of the RGO sheets and simultaneously restored the sp2 carbon networks in the graphene sheets. As a result, the electrical conductivity of RGO-1100℃ (~210 S/cm) film was greatly improved compared with that of RGO (~24 S/cm) and graphene oxide (4.2 × 10–4 S/m) films. In addition, the NO2 gas sensing characteristics of the as-prepared RGO films were studied. The results indicated that RGO films were highly responsive to NO2 at temperature of 200℃.展开更多
文摘Spherical Ni(OH)2 powder coated with Co(OH)2 as raw material was mixed with LiOH to synthesize cathode material for lithium ion battery by using solid-state reaction. After sintered at temperature above 600 ℃, a solid solution with layer structure was formed. The result of XPS shows that it is a concentration gradient material with higher cobalt content at the surface, and the gradient decreases with increasing sintering temperature from 650 to 750 ℃. This new gradient material, called as Co-coated LiNiO2, exhibits excellent electrochemical performances for the cathode of Li-ion batteries in comparison with LiNiO2 and Co-doping LiNiO2. The discharge capacity of Co-coated LiNiO2 is over 180 mA·h/g and capacity decay per cycle is less than 0.07% when Co-coated LiNiO2 consisting of 92% nickel and 8% cobalt was sintered at the temperatures between 650-670 ℃. Though initial discharge capacity could be increased with higher sintering temperature, the cycle life would be reduced.
基金This research is co-financed by Greece and the European Union(European Social Fund-ESF)through the Operational Programme‘Human Resources,Development,Education and Lifelong Learning 2014-2020’in the context of the project‘Innovative wood plastic composites made from recycled polystyrene and recycled wood chips’(MIS 5048422).
文摘The development of alternative wood composites based on the use of waste or recycled materials can be beneficial due to over exploitation of natural resources.Under this frame,an option for the successful utilization of waste polystyrene which avoids environmental problems that formaldehyde adhesives cause and also reduces waste dis-posal,is its potential application as a binder for the production of value-added environmentally friendly and low cost wood composites.Two types of panel were successfully made,consisting of wood dust and two recycled poly-styrene contents,namely,15%and 30%.Both physical properties,water absorption and thickness swelling,and mechanical properties,modulus of rupture,shear strength parallel in the plane of the board and glue line shear strength,were significantly improved as the recycled polystyrene content increased from 15%to 30%.Water absorption and thickness swelling after 24 h immersion in water were improved by 165%and 750%as the recycled polystyrene content increased from 15%to 30%.The magnitude of the improvement in mechanical properties however,was less pronounced than of the physical properties since modulus of rupture,shear strength parallel in the plane of the board and glue line shear strength were increased by 43.6%,50%and 61.5%,respec-tively.The low viscosity of the recycled polystyrene caused more mobility inside the panel matrix and therefore,an improved penetration took place into adequate depth of the compressed dust particles.It is concluded that boards can be successfully produced using these waste raw materials,wood dust and recycled polystyrene in organic solvent as a binder,and therefore it can reduce waste disposal and provide cleaner production for the development of wood-based boards.
基金supported by a Grant Research of Vietnam National University,Ho Chi Minh City(No.B2012-20-10TD)
文摘The demand of higher energy density and higher power capacity of lithium（Li）-ion secondary batteries has led to the search for electrode materials whose capacities and performance are better than those available today. Carbon nanotubes（CNTs）, with their unique properties such as 1D tubular structure, high electrical and thermal conductivities, and extremely large surface area, have been used as materials to prepare cathodes for Li-ion batteries. The structure and morphology of CNTs were analyzed by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, and transmission electron microscopy（TEM）. The functional groups on the purified CNT surface such as –COOH, –OH were characterized by Fourier Transform infrared spectroscopy. The electrode materials were fabricated from LiMn2O4（LMO）, doped spinel LiNi0.5Mn1.5O4, and purified CNTs via solid-state reaction. The structure and morphology of the electrode were characterized using XRD, SEM, and TEM. Finally, the efficiency of the electrode materials using CNTs was evaluated by cyclic voltammetry and electrochemical impedance spectroscopy.
文摘The article investigated the influence of modification process parameters on dispersity of MWNTs DI （in deionized） water and PVA/MWNT composite＇s electrical conductivity. Experimental results obtained by SEM （scanning electron microscope）, TEM （transmission electron microscope）, transform Fourier infrared spectroscopy, pH meter confirmed the most effective conditions in modifying the MWNT surface at the 1：3 mixture of nitric and sulfuric acid at 60 ℃. The extinction coefficient value of functionalized MWNTs at 500 nm wavelength was determined to be 41.24 cm^2·mg^-1, while their dispersibility in DI water was about 12.85 mg/mL and stable in more than 3 weeks via UV-vis spectroscopy. The other important result is the decrease of volume resistivity from 7.98 × 10^6 MΩ·m ofPVA （polyvinyl alcohol） to 4.15 × 10^4 MΩ·m of PVA/1 wt% modified MWNT thin film.
文摘In this research, a highly conductive graphene film was synthesized through the chemical reduction of graphene oxide (RGO) nanosheets followed by thermal treatment at 1100℃ (RGO-1100℃) under H2 ambient. The as-prepared graphene films were characterized by using X-ray photoelectron spectroscopy, fourier transform infrared spectroscopy, X-ray diffractions, raman spectroscopy, transmission electron microscopy, scanning electron microscopy, atomic force microscopy and by electrical conductivity measurements. The results showed that the thermal treatment efficiently removed residual oxygen-containing functional groups on the surface of the RGO sheets and simultaneously restored the sp2 carbon networks in the graphene sheets. As a result, the electrical conductivity of RGO-1100℃ (~210 S/cm) film was greatly improved compared with that of RGO (~24 S/cm) and graphene oxide (4.2 × 10–4 S/m) films. In addition, the NO2 gas sensing characteristics of the as-prepared RGO films were studied. The results indicated that RGO films were highly responsive to NO2 at temperature of 200℃.
