On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to coll...On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to collect particle samples.Gas chromatography-flame ionization detector/mass spectrometry and gas chromatography-mass spectrometry was the offline analysis method.We found that the total mass concentration of the tested 102 VOC species at the outlet of wet flue gas desulfuration device was(13456±47)μg·m^(-3),which contained aliphatic hydrocarbons(57.9%),aromatic hydrocarbons(26.8%),halogen-containing species(14.5%),and a small amount of oxygen-containing and nitrogencontaining species.The most abundant species were 1-hexene,n-hexane and 2-methylpentane.The top ten species in terms of mass fraction(with a total mass fraction of 75.3%)were mainly hydrocarbons with a carbon number of 6 or higher and halogenated hydrocarbons with a lower carbon number.The mass concentration of VOC species in the particle phase was significantly lower than that in the gas phase.The change of VOC mass concentrations along the air pollution control devices indicates that conventional pollutant control equipment had a limited effect on VOC reduction.Ozone formation potential calculations showed that aromatic hydrocarbons contributed the highest ozone formation(46.4%)due to their relatively high mass concentrations and MIR(maximum increment reactivity)values.展开更多
A method of measuring the interactions in a multivariable control sys-tem(MVCS)in time domain is defined in this paper.An intelligent decoupling com-pensator is designed in terms of the concept of fuzzy control,so tha...A method of measuring the interactions in a multivariable control sys-tem(MVCS)in time domain is defined in this paper.An intelligent decoupling com-pensator is designed in terms of the concept of fuzzy control,so that the auto-tuningof controllers’ parameters in a 2×2 MVCS can be turned into that of two independentsingle-loop control systems(SLCS).The method presented in the paper has success-fully been used in a simulation experiment on the automatic tuning of a coordinatedcontrol system(CCS)in the drum-boiler turbogenerating unit(DBTU)and the simu-lation results axe satisfactory.展开更多
This work focuses on the best financial resources allocation to define a wind power plant portfolio, considering a set of feasible sites. To accomplish the problem formulation and solution, the first step was to estab...This work focuses on the best financial resources allocation to define a wind power plant portfolio, considering a set of feasible sites. To accomplish the problem formulation and solution, the first step was to establish a long-term wind series reconstruction methodology for generating scenarios of wind energy, applying it to study five different locations of the Brazilian territory. Secondly, a risk-averse stochastic optimization model was implemented and used to define the optimal wind power plant selection </span><span style="font-family:Verdana;">that</span><span style="font-family:Verdana;"> maximize</span><span style="font-family:Verdana;">s</span><span style="font-family:Verdana;"> the portfolio financial results, considering an investment budget constraint. In a sequence, a case study was developed to illustrate a practical situation of applying the methodology to the portfolio selection problem, considering five wind power plant</span><span style="font-family:Verdana;">s</span><span style="font-family:Verdana;"> options. </span><span style="font-family:Verdana;">The case</span><span style="font-family:Verdana;"> study was supported by the proposed optimization model, using the scenarios of generation created by the reconstruction methodology. The obtained results show the model performance in terms of defining the best financial resources allocation considering the effect of the complementarity between sites, making it feasible to select the optimal set of wind power plants, characterizing a wind plant optimal portfolio that takes into account the budget constraint. The adopted methodology makes it possible to realize that the diversification of the portfolio depends on the investor risk aversion. Although applied to the Brazilian case, this model can be customized to solve a similar problem worldwide.展开更多
In this paper a new market based analytical model is proposed for optimal placement of Wind Turbines (WTs) in power systems. In addition to wind turbines, thermal units (THUs) and Pumped Storage Hydro Power Plants (PS...In this paper a new market based analytical model is proposed for optimal placement of Wind Turbines (WTs) in power systems. In addition to wind turbines, thermal units (THUs) and Pumped Storage Hydro Power Plants (PSHPPs) owners participate in power market. Objective function is defined as participants’ social welfare achieved from power pool and ancillary markets in yearly horizon. Wind turbines have been modeled by probability-generation tree scenarios based on statistical information. We concentrate on investment profits of WTs numbers and its generation capacity beside to PSHPPs and THUs power plants in power systems due to increase in high flexible tools for Independent system operator into the planning and operation planning time interval. For effectiveness evaluation of proposed model, simulation studies are applied on 14-Bus IEEE test power system.展开更多
This study explores the influence of rotor blade angle on stall inception in an axial fan by means of numerical simulations grounded in the Reynolds-Averaged Navier-Stokes(RANS)equations and the Realizable k-εturbule...This study explores the influence of rotor blade angle on stall inception in an axial fan by means of numerical simulations grounded in the Reynolds-Averaged Navier-Stokes(RANS)equations and the Realizable k-εturbulence model.By analyzing the temporal behavior of the outlet static pressure,along with the propagation velocity of stall inception,the research identifies distinct patterns in the development of stall.The results reveal that stall inception originates in the second rotor impeller.At a blade angle of 27°,the stall inception follows a modal wave pattern,while in all other cases,it assumes the form of spike-type stall.The flow field associated with spike stall inception demonstrates a relatively uniform gradient in the radial direction,whereas the modal wave stall case displays a distinctive“L”-shaped propagation feature.At blade angles of multiple stall inceptions are observed.-9°and-18°,These phenomena initiate at the blade’s leading edge,propagate along both axial and radial directions,and transition dynamically between single and multiple inception states.展开更多
Enhancing the fermentation efficiency of waste in waste warehouses is pivotal for accelerating the pyrolysis process and minimizing harmful gas emissions.This study proposes an integrated approach,combining hot air in...Enhancing the fermentation efficiency of waste in waste warehouses is pivotal for accelerating the pyrolysis process and minimizing harmful gas emissions.This study proposes an integrated approach,combining hot air injection with dual atomizing nozzles,for the thermal treatment of waste piles.Numerical simulations are employed to investigate the influence of various parameters,namely,nozzle height,nozzle tilt angle,inlet air velocity and air temperature,on the droplet diffusion process,spread area,droplet temperature,and droplet size distribution.The results show that reducing the nozzle height increases the temperature of droplets upon their deposition on the waste pile.Specifically,when the nozzle height is lowered to 1.5 m,the temperature of the droplets reaching the waste pile is 1℃higher than when the nozzle height is set at 2 m.Furthermore,an increase in the nozzle tilt angle expands the overlapping heating area.For instance,when the nozzle angle is increased from 15°to 30°,the overlapping spread area expands by 3.21 m2.Additionally,increasing the inlet air velocity enhances the droplet diffusion range.At an air velocity of 2 m/s,the droplet diffusion range grows to 14.4 m,representing a 6.7%increase compared to the nowind condition.While the average droplet diameter decreases to 1.53 mm,the droplet temperature decreases by 1℃.Moreover,the droplet temperature is found to become smaller as the ambient temperature inside the waste warehouse declines.Specifically,a 5℃reduction in the ambient temperature results in a 1℃decrease in the average temperature of the atomized droplets.The study concludes that a nozzle height of 1.5 m and a nozzle tilt angle of 30°effectively meet practical heating requirements.展开更多
The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering ...The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uniform flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aerodynamic design methods of an expansion wall and machinery implementation plan for the halfflexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigidflexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard(GJB).展开更多
The heat transfer coefficient in a multidimensional heat conduction problem is obtained from the solution of the inverse heat conduction problem based on the thermographic temperature measurement. The modified one-dim...The heat transfer coefficient in a multidimensional heat conduction problem is obtained from the solution of the inverse heat conduction problem based on the thermographic temperature measurement. The modified one-dimensional correction method （MODCM）, along with the finite volume method, is employed for both two- and three-dimensional inverse problems. A series of numerical experiments are conducted in order to verify the effectiveness of the method. In addition, the effect of the temperature measurement error, the ending criterion of the iteration, etc. on the result of the inverse problem is investigated. It is proved that the method is a simple, stable and accurate one that can solve successfully the inverse heat conduction problem.展开更多
In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using ...In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using non-thermal plasma was investigated using a coaxial dielectric barrier discharge. Comparative experiments were carried out in the dry gas stream with and without Ar respectively at O2 concentration of 0.1%. The results showed that NO could be removed remarkably and it would be enhanced in the presence of Ar in the dry gas stream. It seems that SO2 could not be removed unless there is Ar in the dry gas stream. The mechanism of removal of NO and SO2 in the dry gas stream was discussed.展开更多
A method based on solution of the inverse heat conduction problem was presented for online stress monitoring and fatigue life analysis of boiler drums. The mathematical model of the drum temperature distribution is ba...A method based on solution of the inverse heat conduction problem was presented for online stress monitoring and fatigue life analysis of boiler drums. The mathematical model of the drum temperature distribution is based on the assumptions that the difference of temperature along the longitudinal axis of the boiler drum is negligible with changes only in the radial direction and the circumferential direction, and that the outer surface of drum is thermaUy insulated. Combining this model with the control-volume method provides temperatures at different points on a cross-section of the drum. With the temperature data, the stresses and the life expectancy of the boiler drum are derived according to the ASME code. Applying this method to the cold start-up process of a 300 MW boiler demonstrated the absence of errors caused by the boundary condition assumptions on the inner surface of the drum and testified that the method is an applicable technique for the online stress monitoring and fatigue life analysis of boiler drums.展开更多
The multi-dimensional time-domain computational fluid dynamics(CFD) approach is extended to calculate the acoustic attenuation performance of water-filled piping silencers. Transmission loss predictions from the time-...The multi-dimensional time-domain computational fluid dynamics(CFD) approach is extended to calculate the acoustic attenuation performance of water-filled piping silencers. Transmission loss predictions from the time-domain CFD approach and the frequency-domain finite element method(FEM) agree well with each other for the dual expansion chamber silencer, straight-through and cross-flow perforated tube silencers without flow. Then, the time-domain CFD approach is used to investigate the effect of flow on the acoustic attenuation characteristics of perforated tube silencers. The numerical predictions demonstrate that the mean flow increases the transmission loss, especially at higher frequencies, and shifts the transmission loss curve to lower frequencies.展开更多
In this article, the electrochemical performance of the electrodes of zinc polycrystal, Zn（002） and Zn（100） single crystals were studied by the Tafel line extrapolation of the potentio-dynamic polarization curves,...In this article, the electrochemical performance of the electrodes of zinc polycrystal, Zn（002） and Zn（100） single crystals were studied by the Tafel line extrapolation of the potentio-dynamic polarization curves, the cyclic voltammetry and the charge/discharge experiment. The results shows that in 6.0 mol·L^-1 KOH solution the corrosion rate of Zn polycrystal, Zn（100） and Zn（002） single crystals decreases in turn; and the reversibility and the charge/discharge performance of Zn single crystal was superior to Zn polycrystal. The dendrite growth of the surface of Zn polycrvstal was easier than Zn single crystal during the stages of charge/discharge.展开更多
A simulation model was developed to analyze the steady state and transient operation of a tubular solid oxide fuel cell. The model covers both the electrochemical and the heat transfer models. The electrochemical mode...A simulation model was developed to analyze the steady state and transient operation of a tubular solid oxide fuel cell. The model covers both the electrochemical and the heat transfer models. The electrochemical model deals with the Nernst potential, ohmic polarization, activation polarization, and concentration polarization, while the heat transfer model concerns the heat transfer by conduction, convection and radiation. The numerical results show that the ohmic loss is the dominant one among the three polarizations in a cathode-supported solid oxide fuel cell and in the middle part of a solid oxide fuel cell the temperature is higher than those at both the ends. When the inlet temperature and the flow rates of the fuel and the oxidant are kept constantly, the temperature of the solid structure of the cell will increase due to the increase of power output of the cell from the initial state to the new one.展开更多
Motion of a rectangular particle in a two-dimensional vertical shear flow of Newtonian fluid and viscoelastic fluid with different parameters is studied using the finite element arbitrary Lagrangian–Eulerian domain m...Motion of a rectangular particle in a two-dimensional vertical shear flow of Newtonian fluid and viscoelastic fluid with different parameters is studied using the finite element arbitrary Lagrangian–Eulerian domain method.The results show that the centerline of the channel is a stable equilibrium position for the neutrally buoyant rectangular particle in a vertical shear flow.Inertia causes the particle to migrate towards the centerline of the channel.In addition,a critical elasticity number exists.When the elasticity number is below the critical value,the rectangular particle migrates to the centerline;otherwise the centerline of the channel is apparently no longer a global attractor of trajectories of the particle.展开更多
The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion pro...The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion process were analyzed at a high inlet pressure. A sensitivity analysis of the detailed mechanisms of the surface reaction of methane on Pt revealed that the most sensitive reactions affecting the heterogeneous ignition are oxygen adsorption/desorption and methane adsorption, and the most sensitive reactions affecting the homogeneous ignition are OH and H2O adsorption/desorption. The combustion process of the homogeneous charge compression ignition（HCCI） engine whose piston face was coated with Pt catalyst was simulated. The effects of catalysis and the most sensitive reactions on the ignition timing and the concentration of the main intermediate species during the HCCI engine combustion are discussed. The results show that the ignition timing of the HCCI engine can be increased by catalysis, and the most sensitive reactions affecting the ignition timing of the HCCI engine are OH and H2O adsorption/desorption.展开更多
An experimental study on heat transfer and resistance coefficients of linearly arranged smooth and spirally corrugated tube bundles in cross-flow was performed. The heat transfer and resistance coefficients are presen...An experimental study on heat transfer and resistance coefficients of linearly arranged smooth and spirally corrugated tube bundles in cross-flow was performed. The heat transfer and resistance coefficients are presented in this paper with transverse and longitudinal tube-pitch and tube geometries taken into account. The experiment's results can provide technical guidelines for application to horizontal air preheater with arranged in-line spirally corrugated tube bundles, especially to the air preheater for CFBCBs (Circulating Fluidized Bed Combustion Boilers).展开更多
This paper studies the feasibility of a supply-side wind-coal integrated energy system.Based on grid-side data,the load regulation model of coal-fired power and the wind-coal integrated energy system model are establi...This paper studies the feasibility of a supply-side wind-coal integrated energy system.Based on grid-side data,the load regulation model of coal-fired power and the wind-coal integrated energy system model are established.According to the simulation results,the reasons why the wind-coal combined power supply is difficult to meet the grid-side demand are revealedthrough scenario analysis.Basedon thewind-coal combinedoperation,a wind-coalstorage integrated energy system was proposed by adding lithium-iron phosphate battery energy storage system(LIPBESS)to adjust the load of the system.According to the four load adjustment scenarios of grid-side instructions of the wind-coal system,the difficulty of load adjustment in each scenario is analyzed.Based on the priority degree of LIPBESS charge/discharge in four scenarios at different time periods,the operation mode of two charges and two discharges per day was developed.Based on the independent operation level of coal-fired power,after the addition of LIPBESS(5.5 MWh),the average qualified rate of multi-power operation in March and June reached the level of independent operation of coal-fired power,while the average qualified rate of the remaining months was only 5.4%different from that of independent operation of coal-fired power.Compared with the wind storage mode,the energy storage capacity and investment cost of wind-coal-storage integrated energy system are reduced by 54.2%and 53.7%,respectively.展开更多
In the restructured electricity market,microgrid(MG),with the incorporation of smart grid technologies,distributed energy resources(DERs),a pumped-storage-hydraulic(PSH)unit,and a demand response program(DRP),is a sma...In the restructured electricity market,microgrid(MG),with the incorporation of smart grid technologies,distributed energy resources(DERs),a pumped-storage-hydraulic(PSH)unit,and a demand response program(DRP),is a smarter and more reliable electricity provider.DER consists of gas turbines and renewable energy sources such as photovoltaic systems and wind turbines.Better bidding strategies,prepared by MG operators,decrease the electricity cost and emissions from upstream grid and conventional and renewable energy sources(RES).But it is inefficient due to the very high sporadic characteristics of RES and the very high outage rate.To solve these issues,this study suggests non-dominated sorting genetic algorithm Ⅱ(NSGA-Ⅱ)for an optimal bidding strategy considering pumped hydroelectric energy storage and DRP based on outage conditions and uncertainties of renewable energy sources.The uncertainty related to solar and wind units is modeled using lognormal and Weibull probability distributions.TOU-based DRP is used,especially considering the time of outages along with the time of peak loads and prices,to enhance the reliability of MG and reduce costs and emissions.展开更多
A new method of effectiveness evaluation of weapon systems is set up by improving the formula of approaching degree. According to the grey target theory of grey system theory, the patterns of the weapon systems to be ...A new method of effectiveness evaluation of weapon systems is set up by improving the formula of approaching degree. According to the grey target theory of grey system theory, the patterns of the weapon systems to be evaluated are formed with the main tactical and technical performance indices of these weapon systems, thereby the standard pattern of these patterns is determined. By solving the approaching degree of patterns to their standard one and making a comparison among them, the evaluation results can be obtained.展开更多
基金funded by the National Natural Science Foundation of China(52006079)the Natural Science Foundation of Hubei Province(2020CFB247)the National Key Research and Development Program of China(2018YFB0605201)。
文摘On-site measurements of volatile organic compounds(VOCs)in different streams of flue gas were carried out on a real coal-fired power plant using sampling bags and SUMMA canisters to collect gas samples,filters to collect particle samples.Gas chromatography-flame ionization detector/mass spectrometry and gas chromatography-mass spectrometry was the offline analysis method.We found that the total mass concentration of the tested 102 VOC species at the outlet of wet flue gas desulfuration device was(13456±47)μg·m^(-3),which contained aliphatic hydrocarbons(57.9%),aromatic hydrocarbons(26.8%),halogen-containing species(14.5%),and a small amount of oxygen-containing and nitrogencontaining species.The most abundant species were 1-hexene,n-hexane and 2-methylpentane.The top ten species in terms of mass fraction(with a total mass fraction of 75.3%)were mainly hydrocarbons with a carbon number of 6 or higher and halogenated hydrocarbons with a lower carbon number.The mass concentration of VOC species in the particle phase was significantly lower than that in the gas phase.The change of VOC mass concentrations along the air pollution control devices indicates that conventional pollutant control equipment had a limited effect on VOC reduction.Ozone formation potential calculations showed that aromatic hydrocarbons contributed the highest ozone formation(46.4%)due to their relatively high mass concentrations and MIR(maximum increment reactivity)values.
文摘A method of measuring the interactions in a multivariable control sys-tem(MVCS)in time domain is defined in this paper.An intelligent decoupling com-pensator is designed in terms of the concept of fuzzy control,so that the auto-tuningof controllers’ parameters in a 2×2 MVCS can be turned into that of two independentsingle-loop control systems(SLCS).The method presented in the paper has success-fully been used in a simulation experiment on the automatic tuning of a coordinatedcontrol system(CCS)in the drum-boiler turbogenerating unit(DBTU)and the simu-lation results axe satisfactory.
文摘This work focuses on the best financial resources allocation to define a wind power plant portfolio, considering a set of feasible sites. To accomplish the problem formulation and solution, the first step was to establish a long-term wind series reconstruction methodology for generating scenarios of wind energy, applying it to study five different locations of the Brazilian territory. Secondly, a risk-averse stochastic optimization model was implemented and used to define the optimal wind power plant selection </span><span style="font-family:Verdana;">that</span><span style="font-family:Verdana;"> maximize</span><span style="font-family:Verdana;">s</span><span style="font-family:Verdana;"> the portfolio financial results, considering an investment budget constraint. In a sequence, a case study was developed to illustrate a practical situation of applying the methodology to the portfolio selection problem, considering five wind power plant</span><span style="font-family:Verdana;">s</span><span style="font-family:Verdana;"> options. </span><span style="font-family:Verdana;">The case</span><span style="font-family:Verdana;"> study was supported by the proposed optimization model, using the scenarios of generation created by the reconstruction methodology. The obtained results show the model performance in terms of defining the best financial resources allocation considering the effect of the complementarity between sites, making it feasible to select the optimal set of wind power plants, characterizing a wind plant optimal portfolio that takes into account the budget constraint. The adopted methodology makes it possible to realize that the diversification of the portfolio depends on the investor risk aversion. Although applied to the Brazilian case, this model can be customized to solve a similar problem worldwide.
文摘In this paper a new market based analytical model is proposed for optimal placement of Wind Turbines (WTs) in power systems. In addition to wind turbines, thermal units (THUs) and Pumped Storage Hydro Power Plants (PSHPPs) owners participate in power market. Objective function is defined as participants’ social welfare achieved from power pool and ancillary markets in yearly horizon. Wind turbines have been modeled by probability-generation tree scenarios based on statistical information. We concentrate on investment profits of WTs numbers and its generation capacity beside to PSHPPs and THUs power plants in power systems due to increase in high flexible tools for Independent system operator into the planning and operation planning time interval. For effectiveness evaluation of proposed model, simulation studies are applied on 14-Bus IEEE test power system.
基金the Natural Science Foundation of Hebei Province,China(Grant No.E2022502052)Fundamental Research Funds for the Central Universities,China(Grant No.2022MS081)Fundamental Research Funds for the Central Universities,China(Grant No.2023MS121).
文摘This study explores the influence of rotor blade angle on stall inception in an axial fan by means of numerical simulations grounded in the Reynolds-Averaged Navier-Stokes(RANS)equations and the Realizable k-εturbulence model.By analyzing the temporal behavior of the outlet static pressure,along with the propagation velocity of stall inception,the research identifies distinct patterns in the development of stall.The results reveal that stall inception originates in the second rotor impeller.At a blade angle of 27°,the stall inception follows a modal wave pattern,while in all other cases,it assumes the form of spike-type stall.The flow field associated with spike stall inception demonstrates a relatively uniform gradient in the radial direction,whereas the modal wave stall case displays a distinctive“L”-shaped propagation feature.At blade angles of multiple stall inceptions are observed.-9°and-18°,These phenomena initiate at the blade’s leading edge,propagate along both axial and radial directions,and transition dynamically between single and multiple inception states.
文摘Enhancing the fermentation efficiency of waste in waste warehouses is pivotal for accelerating the pyrolysis process and minimizing harmful gas emissions.This study proposes an integrated approach,combining hot air injection with dual atomizing nozzles,for the thermal treatment of waste piles.Numerical simulations are employed to investigate the influence of various parameters,namely,nozzle height,nozzle tilt angle,inlet air velocity and air temperature,on the droplet diffusion process,spread area,droplet temperature,and droplet size distribution.The results show that reducing the nozzle height increases the temperature of droplets upon their deposition on the waste pile.Specifically,when the nozzle height is lowered to 1.5 m,the temperature of the droplets reaching the waste pile is 1℃higher than when the nozzle height is set at 2 m.Furthermore,an increase in the nozzle tilt angle expands the overlapping heating area.For instance,when the nozzle angle is increased from 15°to 30°,the overlapping spread area expands by 3.21 m2.Additionally,increasing the inlet air velocity enhances the droplet diffusion range.At an air velocity of 2 m/s,the droplet diffusion range grows to 14.4 m,representing a 6.7%increase compared to the nowind condition.While the average droplet diameter decreases to 1.53 mm,the droplet temperature decreases by 1℃.Moreover,the droplet temperature is found to become smaller as the ambient temperature inside the waste warehouse declines.Specifically,a 5℃reduction in the ambient temperature results in a 1℃decrease in the average temperature of the atomized droplets.The study concludes that a nozzle height of 1.5 m and a nozzle tilt angle of 30°effectively meet practical heating requirements.
基金supported by the National Natural Science Foundation of China (Nos. 90916023 and 51176075)
文摘The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uniform flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aerodynamic design methods of an expansion wall and machinery implementation plan for the halfflexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigidflexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard(GJB).
文摘The heat transfer coefficient in a multidimensional heat conduction problem is obtained from the solution of the inverse heat conduction problem based on the thermographic temperature measurement. The modified one-dimensional correction method （MODCM）, along with the finite volume method, is employed for both two- and three-dimensional inverse problems. A series of numerical experiments are conducted in order to verify the effectiveness of the method. In addition, the effect of the temperature measurement error, the ending criterion of the iteration, etc. on the result of the inverse problem is investigated. It is proved that the method is a simple, stable and accurate one that can solve successfully the inverse heat conduction problem.
基金Project supported by the National Natural Sciences Foundation of China(No.50576037)Natural Science Foundation of Jiangsu Province(No.BK2006198)
文摘In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using non-thermal plasma was investigated using a coaxial dielectric barrier discharge. Comparative experiments were carried out in the dry gas stream with and without Ar respectively at O2 concentration of 0.1%. The results showed that NO could be removed remarkably and it would be enhanced in the presence of Ar in the dry gas stream. It seems that SO2 could not be removed unless there is Ar in the dry gas stream. The mechanism of removal of NO and SO2 in the dry gas stream was discussed.
基金Funded by the National Science and Technology Support Project of China (No. 2006BAA03B02-03)
文摘A method based on solution of the inverse heat conduction problem was presented for online stress monitoring and fatigue life analysis of boiler drums. The mathematical model of the drum temperature distribution is based on the assumptions that the difference of temperature along the longitudinal axis of the boiler drum is negligible with changes only in the radial direction and the circumferential direction, and that the outer surface of drum is thermaUy insulated. Combining this model with the control-volume method provides temperatures at different points on a cross-section of the drum. With the temperature data, the stresses and the life expectancy of the boiler drum are derived according to the ASME code. Applying this method to the cold start-up process of a 300 MW boiler demonstrated the absence of errors caused by the boundary condition assumptions on the inner surface of the drum and testified that the method is an applicable technique for the online stress monitoring and fatigue life analysis of boiler drums.
基金Project(11174065)supported by the National Natural Science Foundation of China
文摘The multi-dimensional time-domain computational fluid dynamics(CFD) approach is extended to calculate the acoustic attenuation performance of water-filled piping silencers. Transmission loss predictions from the time-domain CFD approach and the frequency-domain finite element method(FEM) agree well with each other for the dual expansion chamber silencer, straight-through and cross-flow perforated tube silencers without flow. Then, the time-domain CFD approach is used to investigate the effect of flow on the acoustic attenuation characteristics of perforated tube silencers. The numerical predictions demonstrate that the mean flow increases the transmission loss, especially at higher frequencies, and shifts the transmission loss curve to lower frequencies.
文摘In this article, the electrochemical performance of the electrodes of zinc polycrystal, Zn（002） and Zn（100） single crystals were studied by the Tafel line extrapolation of the potentio-dynamic polarization curves, the cyclic voltammetry and the charge/discharge experiment. The results shows that in 6.0 mol·L^-1 KOH solution the corrosion rate of Zn polycrystal, Zn（100） and Zn（002） single crystals decreases in turn; and the reversibility and the charge/discharge performance of Zn single crystal was superior to Zn polycrystal. The dendrite growth of the surface of Zn polycrvstal was easier than Zn single crystal during the stages of charge/discharge.
文摘A simulation model was developed to analyze the steady state and transient operation of a tubular solid oxide fuel cell. The model covers both the electrochemical and the heat transfer models. The electrochemical model deals with the Nernst potential, ohmic polarization, activation polarization, and concentration polarization, while the heat transfer model concerns the heat transfer by conduction, convection and radiation. The numerical results show that the ohmic loss is the dominant one among the three polarizations in a cathode-supported solid oxide fuel cell and in the middle part of a solid oxide fuel cell the temperature is higher than those at both the ends. When the inlet temperature and the flow rates of the fuel and the oxidant are kept constantly, the temperature of the solid structure of the cell will increase due to the increase of power output of the cell from the initial state to the new one.
基金by the Natural Science Fund of Chongqing Committee of Science and Technology(No CSTC.2006BA3023).
文摘Motion of a rectangular particle in a two-dimensional vertical shear flow of Newtonian fluid and viscoelastic fluid with different parameters is studied using the finite element arbitrary Lagrangian–Eulerian domain method.The results show that the centerline of the channel is a stable equilibrium position for the neutrally buoyant rectangular particle in a vertical shear flow.Inertia causes the particle to migrate towards the centerline of the channel.In addition,a critical elasticity number exists.When the elasticity number is below the critical value,the rectangular particle migrates to the centerline;otherwise the centerline of the channel is apparently no longer a global attractor of trajectories of the particle.
基金Supported by the National Key Basic Research Development Project of China(No.2001CB209201).
文摘The catalytic combustion of methane in a mierochannel whose surface was coated with platinum（Pt） catalyst was studied by numerical-simulation. The effects of gas-phase reactions on the whole catalytic combustion process were analyzed at a high inlet pressure. A sensitivity analysis of the detailed mechanisms of the surface reaction of methane on Pt revealed that the most sensitive reactions affecting the heterogeneous ignition are oxygen adsorption/desorption and methane adsorption, and the most sensitive reactions affecting the homogeneous ignition are OH and H2O adsorption/desorption. The combustion process of the homogeneous charge compression ignition（HCCI） engine whose piston face was coated with Pt catalyst was simulated. The effects of catalysis and the most sensitive reactions on the ignition timing and the concentration of the main intermediate species during the HCCI engine combustion are discussed. The results show that the ignition timing of the HCCI engine can be increased by catalysis, and the most sensitive reactions affecting the ignition timing of the HCCI engine are OH and H2O adsorption/desorption.
文摘An experimental study on heat transfer and resistance coefficients of linearly arranged smooth and spirally corrugated tube bundles in cross-flow was performed. The heat transfer and resistance coefficients are presented in this paper with transverse and longitudinal tube-pitch and tube geometries taken into account. The experiment's results can provide technical guidelines for application to horizontal air preheater with arranged in-line spirally corrugated tube bundles, especially to the air preheater for CFBCBs (Circulating Fluidized Bed Combustion Boilers).
基金supported by the Natural Science Foundation of China(Grant No.52076079)Natural Science Foundation of Hebei Province,China(Grant No.E2020502013)the Fundamental Research Funds for the Central Universities(2021MS076,2021MS079).
文摘This paper studies the feasibility of a supply-side wind-coal integrated energy system.Based on grid-side data,the load regulation model of coal-fired power and the wind-coal integrated energy system model are established.According to the simulation results,the reasons why the wind-coal combined power supply is difficult to meet the grid-side demand are revealedthrough scenario analysis.Basedon thewind-coal combinedoperation,a wind-coalstorage integrated energy system was proposed by adding lithium-iron phosphate battery energy storage system(LIPBESS)to adjust the load of the system.According to the four load adjustment scenarios of grid-side instructions of the wind-coal system,the difficulty of load adjustment in each scenario is analyzed.Based on the priority degree of LIPBESS charge/discharge in four scenarios at different time periods,the operation mode of two charges and two discharges per day was developed.Based on the independent operation level of coal-fired power,after the addition of LIPBESS(5.5 MWh),the average qualified rate of multi-power operation in March and June reached the level of independent operation of coal-fired power,while the average qualified rate of the remaining months was only 5.4%different from that of independent operation of coal-fired power.Compared with the wind storage mode,the energy storage capacity and investment cost of wind-coal-storage integrated energy system are reduced by 54.2%and 53.7%,respectively.
文摘In the restructured electricity market,microgrid(MG),with the incorporation of smart grid technologies,distributed energy resources(DERs),a pumped-storage-hydraulic(PSH)unit,and a demand response program(DRP),is a smarter and more reliable electricity provider.DER consists of gas turbines and renewable energy sources such as photovoltaic systems and wind turbines.Better bidding strategies,prepared by MG operators,decrease the electricity cost and emissions from upstream grid and conventional and renewable energy sources(RES).But it is inefficient due to the very high sporadic characteristics of RES and the very high outage rate.To solve these issues,this study suggests non-dominated sorting genetic algorithm Ⅱ(NSGA-Ⅱ)for an optimal bidding strategy considering pumped hydroelectric energy storage and DRP based on outage conditions and uncertainties of renewable energy sources.The uncertainty related to solar and wind units is modeled using lognormal and Weibull probability distributions.TOU-based DRP is used,especially considering the time of outages along with the time of peak loads and prices,to enhance the reliability of MG and reduce costs and emissions.
文摘A new method of effectiveness evaluation of weapon systems is set up by improving the formula of approaching degree. According to the grey target theory of grey system theory, the patterns of the weapon systems to be evaluated are formed with the main tactical and technical performance indices of these weapon systems, thereby the standard pattern of these patterns is determined. By solving the approaching degree of patterns to their standard one and making a comparison among them, the evaluation results can be obtained.
