Li metal is widely recognized as the desired anode for next-generation energy storage,Li metal batteries,due to its highest theoretical capacity and lowest potential.Nonetheless,it suffers from unstable electrochemica...Li metal is widely recognized as the desired anode for next-generation energy storage,Li metal batteries,due to its highest theoretical capacity and lowest potential.Nonetheless,it suffers from unstable electrochemical behaviors like dendrite growth and side reactions in practical application.Herein,we report a highly stable anode with collector,Li_(5)Mg@Cu,realized by the melting-rolling process.The Li_(5)Mg@Cu anode delivers ultrahigh cycle stability for 2000 and 1000 h at the current densities of 1 and 2 mA cm^(-2),respectively in symmetric cells.Meanwhile,the Li_(5)Mg@Cu|LFP cell exhibits a high-capacity retention of 91.8% for 1000 cycles and 78.8% for 2000 cycles at 1 C.Moreover,we investigate the suppression effects of Mg on the dendrite growth by studying the performance of Li_(x)Mg@Cu electrodes with different Mg contents(2.0-16.7 at%).The exchange current density,surface energy,Li^(+)diffusion coefficient,and chemical stability of Li_(x)Mg@Cu concretely reveal this improving suppression effect when Mg content becomes higher.In addition,a Mg-rich phase with“hollow brick”morphology forming in the high Mg content Li_(x)Mg@Cu guides the uniform deposition of Li.This study reveals the suppression effects of Mg on Li dendrites growth and offers a perspective for finding the optimal component of Li-Mg alloys.展开更多
In this work,atomic Co catalysts are anchored on a three-dimensional(3D)interconnected g-C_(3)N_(4)(SACo-CN)through Co-N coordination,which exhibit efficient charge carrier transition and low activation energy barrier...In this work,atomic Co catalysts are anchored on a three-dimensional(3D)interconnected g-C_(3)N_(4)(SACo-CN)through Co-N coordination,which exhibit efficient charge carrier transition and low activation energy barriers for peroxymonosulfate(PMS).The incorporation of Co atoms extends the absorption spectrum and enhances the photoelectron-hole separation efficiency of the SACo-CN samples.The 3D interconnected structure,combined with the synergistic interplay between Co-N coordination and visible light irradiation,results in SACo-CN catalysts demonstrating excellent catalytic activity and stability for PMS activation.This leads to a degradation rate of 98.8%for oxytetracycline(OTC)within 30 min under visible light.The research proposes three potential mineralization pathways with eight intermediates,leading to a significant decrease in the toxicity of the intermediates.This work provides a facile and promising approach for the preparation of metal single atom catalysts with highly efficient PMS activation performance.展开更多
High-entropy metal phosphide(HEMP)has considerable potential as an electrocatalyst owing to its beneficial properties,including high-entropy alloy synergy as well as the controllable structure and high conductivity of...High-entropy metal phosphide(HEMP)has considerable potential as an electrocatalyst owing to its beneficial properties,including high-entropy alloy synergy as well as the controllable structure and high conductivity of phosphides.Herein,electrospinning and in situ phosphating were employed to prepare three-dimensional(3D)networks of self-supporting HEMP nanofibers with varying degrees of phosphate content.Comprehensive characterizations via X-ray diffraction and X-ray photoelectron spectroscopy,as well as density functional theory calculations,demonstrate that the introduction of phosphorus(P)atoms to HEMP carbon nanofibers mediates their electronic structure,leads to lattice expansion,which in turn enhances their catalytic performance in the hydrogen evolution reaction(HER).Moreover,the formation of metal-P bonds weakens metal-metal interaction and decreases the free energy of hydrogen adsorption,contributing to the exceptional activity observed in the HEMP catalyst.Electrochemical measurements demonstrate that the HEMP-0.75 catalyst with an ultralow loading of 1.22 wt%ruthenium(Ru)exhibits the highest HER catalytic activity and stability in a 1 M KOH electrolyte,achieving a minimal overpotential of 26 mV at a current density of 10 mA·cm^(-2)and Tafel slope of 50.9 mV·dec^(-1).展开更多
In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool ma...In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool materials and design, tool wea,, processing temperature, material flow, processing window and residual stresses. A particular emphasis is given to microstructural aspects and microstructure-properties relationship. Potential engineering applications are highlighted.展开更多
Microstructure evolution and dynamic restoration mechanism of solution-treated Mg-4Y-2Nd-1Sm-0.5Zr alloy have been studied under three TMP parameters consisting of deformation temperatures(350-500℃),strain rates(0.01...Microstructure evolution and dynamic restoration mechanism of solution-treated Mg-4Y-2Nd-1Sm-0.5Zr alloy have been studied under three TMP parameters consisting of deformation temperatures(350-500℃),strain rates(0.01-5 s^(-1)),and strains(0.2,0.4,and 0.8).A strong dynamic softening is observed in all stress-strain curves,even at higher strain rates(1 and 5 s^(-1))due to an adiabatic heating effect.Various stress-strain curves are applied to construct a processing map and develop an Arrhenius-type constitutive equation.With the prediction of the processing map,an optimal processing domain has been determined to be the temperature range 450-500℃and strain rate range 0.01-0.1 s^(-1)at a strain of 0.8.The volume fraction of DRX grains is the largest in the corresponding domain of high temperature and low strain rate.For the effect of TMP parameters on the dynamic restoration,the discontinuous dynamic recrystallization(DDRX)and continuous DRX(CDRX)synergistic effect occur throughout the whole process at high temperature and high strain rate.In terms of high temperature and low strain rate,DDRX characteristics at a low strain and then the DDRX+CDRX synergistic effect is observed at a higher strain.Although the DRX process is weak at low temperature and low strain rate,deformation twins have occurred and provided nucleation sites for DRX grains.展开更多
The microstructural factors contributing to the high strength of additive-manufactured Al-Si alloys us-ing laser-beam powder bed fusion(PBF-LB)were identified by in-situ synchrotron X-ray diffraction in tensile deform...The microstructural factors contributing to the high strength of additive-manufactured Al-Si alloys us-ing laser-beam powder bed fusion(PBF-LB)were identified by in-situ synchrotron X-ray diffraction in tensile deformation and transmission electron microscopy.PBF-LB and heat treatment were employed to manufacture Al-12%Si binary alloy specimens with different microstructures.At an early stage of de-formation prior to macroscopic yielding,stress was dominantly partitioned into the α-Al matrix,rather than the Si phase in all specimens.Highly concentrated Si solute(~3%)in the α-Al matrix promoted the dynamic precipitation of nanoscale Si phase during loading,thereby increasing the yield strength.After macroscopic yielding,the partitioned stress in the Si phase monotonically increased in the strain-hardening regime with an increase in the dislocation density in the α-Al matrix.At a later stage of strain hardening,the flow curves of the partitioned stress in the Si phase yielded stress relaxation owing to plastic deformation.Therefore,Si-phase particles localized along the cell walls in the cellular-solidified microstructure play a significant role in dislocation obstacles for strain hardening.Compared with the results of the heat-treated specimens with different microstructural factors,the dominant strengthening factors of PBF-LB manufactured Al-Si alloys were discussed.展开更多
The high cost of using the niobium(Nb)barrier for manufacturing magnesium diboride(MgB2)mono-and multi-filamentary wires for large-scale applications has become one of the barriers to replacing current commercial niob...The high cost of using the niobium(Nb)barrier for manufacturing magnesium diboride(MgB2)mono-and multi-filamentary wires for large-scale applications has become one of the barriers to replacing current commercial niobium-titanium superconductors.The potential of replacing the Nb barrier with a low-cost iron(Fe)barrier for multifilament MgB2 superconducting wires is investigated in this manuscript.Therefore,MgB2 wires with Fe barrier sintered with different temperatures are studied(from 650°C to 900°C for 1 h)to investigate the non-superconducting reaction phase of Fe-B.Their superconducting performance including engineering critical current density(Je)and n-value are tested at 4.2 K in various external magnetic fields.The best sample sintered at 650°C for 1 h has achieved a Je value of 3.64×10^(4) A cm^(−2) and an n-value of 61 in 2 T magnetic field due to the reduced formation of Fe2B,better grain connectivity and homogenous microstructure.For microstructural analysis,the focused ion beam(FIB)is utilised for the first time to acquire three-dimensional microstructures and elemental mappings of the interface between the Fe barrier and MgB2 core of different wires.The results have shown that if the sintering temperature can be controlled properly,the Je and n-value of the wire are still acceptable for magnet applications.The formation of Fe2B is identified along the edge of MgB2,as the temperature increases,the content of Fe2B also increases which causes the degradation in the performance of wires.展开更多
Sweat contains numerous vital biomarkers such as metabolites,electrolytes,proteins,nucleic acids and antigens that reflect hydration status,exhaustion,nutrition,and physiological changes.Conventional healthcare diagno...Sweat contains numerous vital biomarkers such as metabolites,electrolytes,proteins,nucleic acids and antigens that reflect hydration status,exhaustion,nutrition,and physiological changes.Conventional healthcare diagnosis relies on disease diagnostics in sophisticated centralized laboratories with invasive sample collection(e.g.,chemical analyses,plasma separation via centrifugation,tissue biopsy,etc.).Cutting-edge point-of-care diagnostics for sweat biomarker analysis allow for non-invasive monitoring of physiologically related biomarkers in sweat and real-time health status tracking.Moreover,using advanced nanoarchitectures,including nanostructured platforms and nanoparticles,can enhance the specificity,sensitivity,wearability and widen the sensing modality of sweat biosensors.Herein,we comprehensively review the secretory mechanisms,clinical uses of sweat biomarkers,and the design,principle,and latest technologies of sweat biosensors.With an emphasis on cutting-edge technologies for sweat biomarker analysis,this review chronicles the issues associated with the current sweat biomarkers analysis of sweat biomarkers and provides insights into strategies for enhancing the translation of such biosensors into routine clinical practice.展开更多
The tensile creep anisotropy of a dilute-alloyed Mg-0.3wt%Ca sheet is investigated along the rolling direction(RD)and normal direction(ND).Strong creep anisotropy is shown between the RD and ND,owing to the easy twinn...The tensile creep anisotropy of a dilute-alloyed Mg-0.3wt%Ca sheet is investigated along the rolling direction(RD)and normal direction(ND).Strong creep anisotropy is shown between the RD and ND,owing to the easy twinning and the Ca-segregation along twin boundaries during creep loading along the ND.To weaken the creep anisotropy,hot-compression parallel to the RD-ND plane is performed and the continuous dynamic recrystallization mechanism induces a bimodal microstructure with the coexistence of unrecrystallized and recrystallized grains.The creep anisotropy is successfully weakened after hot-compression,and the creep resistance is also significantly enhanced along both loading directions.With the assistance of microstructural characterization,the weakened creep anisotropy is ascribed to the dislocation arrays in the interiors of recrystallized grains and the Ca-segregation along the boundaries of recrystallized grains.Compared to commercial Mg alloys with poor creep property and rare-earth alloyed Mg with high price,good creep performance and low production cost can be synchronously realized in the hot-compressed Mg-0.3wt%Ca alloy.Thus,this work proposes a new perspective for producing creep-resistant Mg alloys.展开更多
The study systematically investigated the effects of master alloy addition containing rare earth elements La and Yb on the microstructures characteristic and tensile properties of A1Sil0Cu3 alloy. It was studied by me...The study systematically investigated the effects of master alloy addition containing rare earth elements La and Yb on the microstructures characteristic and tensile properties of A1Sil0Cu3 alloy. It was studied by means of optical microscopy, X-ray diffraction, scanning electron microscopy, energy diffraction spectnam and differential thermal analyzer. The results showed that the ad-dition of （La＋Yb） obviously reduced the sizes of the primary a-Al phase and eutectic Si particles as well as 13-A15FeSi phase and im- proved the morphology of the primary a-A1 phase and eutectic Si particles. The optimum addition of（La＋Yb） addition was 0.6 wt.%. Comparing the 0.6 wt.% （La＋Yb） modified A1Sil0Cu3 alloy with the unmodified alloy, it was found that the mean diameter, mean area and SADS of primary a-A1 phase were decreased by 50.80%, 75.74% and 50.83% respectively; the aspect ratio, size （length） and mean area of eutectic Si particles were decreased by 66.30%, 81.78% and 78.99%, respectively, and the average size of the β-AlsFeSi phase was 16.4 pro. In addition, the addition of （La＋Yb） greatly improved the tensile properties ofA1Si 10Cu3 alloy, especially in the ultimate tensile strength and elongation as a result of the significant improvement in microstructure.展开更多
Abstract： Semi-solid A12Y/AZ91 magnesium matrix composites slurry was prepared by ultrasonic vibration, effect of ultrasonic vi bration temperature and time on microstructure of semi-solid slurry was investigated. Th...Abstract： Semi-solid A12Y/AZ91 magnesium matrix composites slurry was prepared by ultrasonic vibration, effect of ultrasonic vi bration temperature and time on microstructure of semi-solid slurry was investigated. The results showed that with the ultrasonic vibration temperature decreasing the solid volume fraction of semi-solid slurry increased. The best ultrasonic vibration temperature was 600 ℃. With the increase of ultrasonic vibration time, the average grain diameter of primary a-Mg particles decreased firstly, then increased, the average shape factor increased gradually and decreased slightly after 90 s, and a few rosette dendrites were observed after 120 s. The best semi-solid slurry with average grain diameter of 75 μm and shape factor of 0.7 were gained after the melt was treated by ultrasonic vibration for about 60 s at near liquidus temperature （600 ℃）. At last, the microstructure evolution mechanism of semi-solid magnesium matrix composites slurry was analyzed by the theories of thermodynamics and kinetics.展开更多
In this study, two kinds of Al–La master alloys were prepared by ultrasonic method and ordinary mixmelting method, and both of the alloys were added into the Al alloy.Then, the microstructure of Al–La master alloy a...In this study, two kinds of Al–La master alloys were prepared by ultrasonic method and ordinary mixmelting method, and both of the alloys were added into the Al alloy.Then, the microstructure of Al–La master alloy and the modification effect on the Al alloy were investigated using optical microscope(OM), X-ray diffraction(XRD), scanning electron microscope(SEM), and energy disperse spectroscopy(EDS).The results show that because of ultrasonic cavitation and streaming, the grain size of Al–La master alloy prepared by the ultrasonic method is refined, which distributes evenly.And, there is no gas hole,inclusion, or segregation in the Al–La master alloy with aAl, La, and La3Al11.Furthermore, Al–La master alloys show a nice modification for Al alloy, which is much better than that prepared by ordinary mix-melting method.展开更多
The influence of heat treatment（T6） on the ambient temperature dry sliding wear behavior of the extruded AZ91 alloy treated with Y using a pin-on-disc apparatus was investigated. Wear rates and friction coefficients...The influence of heat treatment（T6） on the ambient temperature dry sliding wear behavior of the extruded AZ91 alloy treated with Y using a pin-on-disc apparatus was investigated. Wear rates and friction coefficients were measured within a load range of 5-70 N at a sliding speed of 0.188 m/s over a constant sliding distance of 226.195 m. Worn surfaces and debris were examined using a scanning electron microscope equipped with an energy dispersive spectrometer. The experimental results revealed that, as applied load was increased, the alloy wear rates increased, but the friction coefficients decreased. Four chief operating wear mechanisms were observed, i.e., abrasion, oxidation, delamination and plastic deformation. The extruded AZ91 alloy treated with Y exhibited better wear resistance by adopting T6, which was mainly due to large amounts of fine Mg_（17）Al_（12） distributed in the grains and the resulting modified strength and micro-hardness.展开更多
The solidification behaviors of AZ61 magnesium alloy under a high magnetic field were studied. The corrosion property of AZ61 alloy was investigated in a solution of 3.5 mol/L NaCI by measuring electrochemical p.olari...The solidification behaviors of AZ61 magnesium alloy under a high magnetic field were studied. The corrosion property of AZ61 alloy was investigated in a solution of 3.5 mol/L NaCI by measuring electrochemical p.olarization. The results show that the high magnetic field can refine microstructure and benefit aluminum transfer. The crystal of α-Mg is induced to orient with their c-axis parallel to the magnetic field. The corrosion studies indicate that different crystal plane of magnesium has different corrosion property. The passivating films on the α- and b-planes have higher corrosion resistance than that on the c-plane. Aligned structure affects the corrosion property of AZ61 magnesium alloy.展开更多
To identify the microstructural features of the lattice structures of Al alloys built via the selective laser melting(SLM)process,AlSil OMg alloy with a body-centered cubic(BCC)-type lattice structure was prepared.Cha...To identify the microstructural features of the lattice structures of Al alloys built via the selective laser melting(SLM)process,AlSil OMg alloy with a body-centered cubic(BCC)-type lattice structure was prepared.Characteristic microstructures comprising melt pools with several columnarα-Al phases with<001>orientations along the elongation direction and surrounded by eutectic Si particles were observed at all portions of the built lattice structure.In the node portions of the lattice structure,a gradient microstructure(continuous change in microstructure)was observed.The columnarα-Al phases were observed near the top surface of the node portion,whereas they became coarser and more equiaxed near the bottom surface,resulting in softening localized near the bottom surface.In the strut portions of the lattice structure,the columnarα-Al phases were elongated along the inclined direction of struts.This trend was more prevalent near the bottom surface.Theα-Al phases became coarser and more equiaxed near the bottom surface as well.The aforementioned results were the basis of a discussion of the development of the gradient microstructure in lattice-structured Al alloys during the SLM process in terms of thermal conductivities at the boundaries between the manufactured(locally melted and rapidly solidified)portions and adjacent(unmelted)alloy powder.展开更多
The effect of equal-channel angular pressing(ECAP) on the pitting corrosion resistance of anodized Al-Cu alloy was investigated by electrochemical techniques in a solution containing 0.2 mol/L AlCl3 and also by surfac...The effect of equal-channel angular pressing(ECAP) on the pitting corrosion resistance of anodized Al-Cu alloy was investigated by electrochemical techniques in a solution containing 0.2 mol/L AlCl3 and also by surface analysis.Anodizing was conducted for 20 min at 200 and 400 A/m2 in a solution containing 1.53 mol/L H2SO4 and 0.018 5 mol/L Al2(SO4)3·16H2O at 20 ℃.Anodized Al-Cu alloy was immediately dipped in boiling water for 20 min to seal the micro pores present in anodic oxide films.The time required before initiating pitting corrosion of anodized Al-Cu alloy is longer with ECAP than without,indicating that ECAP process improves the pitting corrosion resistance of anodized Al-Cu alloy.Second phase precipitates such as Si,Al-Cu-Mg and Al-Cu-Si-Fe-Mn intermetallic compounds are present in Al-Cu alloy and the size of these precipitates is greatly decreased by application of ECAP.Al-Cu-Mg intermetallic compounds are dissolved during anodization,whereas the precipitates composed of Si and Al-Cu-Si-Fe-Mn remain in anodic oxide films due to their more noble corrosion potential than Al.FE-SEM and EPMA observation reveal that the pitting corrosion of anodized Al-Cu alloy occurs preferentially around Al-Cu-Si-Fe-Mn intermetallic compounds,since the anodic oxide films are absent at the boundary between the normal oxide films and these impurity precipitates.The improvement of pitting corrosion resistance of anodized Al-Cu alloy processed by ECAP appears to be attributed to a decrease in the size of precipitates,which act as origins of pitting corrosion.展开更多
We utilized electron backscatter diffraction to investigate the microstructure evolutions of a newly developed magnesium-rare earth alloy(Mg–9.80 Gd–3.78 Y–1.12 Sm–0.48 Zr)during instantaneous hot indirect extrusi...We utilized electron backscatter diffraction to investigate the microstructure evolutions of a newly developed magnesium-rare earth alloy(Mg–9.80 Gd–3.78 Y–1.12 Sm–0.48 Zr)during instantaneous hot indirect extrusion.An equiaxed fine-grained(average grain size of 3.4±0.2μm)microstructure with a weak texture was obtained.The grain refinement was mainly attributed to the discontinuous dynamic recrystallization(DDRX)and continuous DRX(CDRX)processes during the hot indirect extrusion process.The twin boundaries formed during the initial deformation stage effectively increased the number of high angle grain boundaries(HAGBs),which provided sites for new grain nuclei,and hence,resulted in an improved DDRX process.Along with DDRX,CDRX processes characterized by low angle grain boundary(LAGB)networks were also observed in the grain interior due to effective dynamic recovery(DRV)at a relatively high temperature of 773 K and high strain rates.Thereafter,LAGB networks were transformed into HAGB networks by the progressive rotation of subgrains during the CDRX process.展开更多
The deformation mechanism of slips and twins has a considerable influence on the plasticity of magnesium alloys. However, the roles of slips and twins in the room-temperature deformation of Mg-rare earth(Mg-RE) alloys...The deformation mechanism of slips and twins has a considerable influence on the plasticity of magnesium alloys. However, the roles of slips and twins in the room-temperature deformation of Mg-rare earth(Mg-RE) alloys with high contents of rare earth elements is rarely investigated. Here, the microstructural evolution and deformation mechanism of an aged Mg-5 Y-2 Nd-3 Sm-0.5 Zr alloy during uniaxial compression at room temperature were systematically investigated using in-situ electron-backscattered diffraction and transmission electron microscopy. The results indicated that in the early stage of deformation, the Mg-RE alloy was mainly controlled by the slip of dislocations in the basal plane and the coordinated c-axis strain of the {10-12} twin. With an increase in the strain, the grain orientation became more suitable for the initiation of pyramidal Ⅱ dislocations in the later stage of deformation;these dominated the deformation mechanism. In the twin evolution of the Mg-RE alloy, there were three types of twin-twin interaction behaviors:(i) single twin variant 'parallel' structure,(ii) single twin variant 'cross' structure, and(iii) multi twin variant 'cross' structure. In addition, three types of twin-grain boundary interaction behaviors were summarized:(i) twin 'refracting through' grain boundary,(ii) twin'parallel through' grain boundary, and(iii) twin 'fusing through' grain boundary, which are expected to act as new means and solutions for the twin strengthening of magnesium alloys.展开更多
The rheological behavior of semisolid Mg_(2)Si/AM60 composites prepared by ultrasonic vibration treatment was investigated.The effects of primaryα-Mg solid content,the ultrasonic power and the content of reinforcemen...The rheological behavior of semisolid Mg_(2)Si/AM60 composites prepared by ultrasonic vibration treatment was investigated.The effects of primaryα-Mg solid content,the ultrasonic power and the content of reinforcement phase Mg_(2)Si on the apparent viscosity of semisolid composites were discussed.The results show that the apparent viscosity of the semis olid composites increases with the increase in a-Mg solid content.Meanwhile,the apparent viscosity decreases with the increase in ultrasonic power,and the reduction amplitude is higher when the solid content is higher.In addition,the apparent viscosity increases with the increase in Mg_(2)Si content.Based on experimental data fitting,the rheological model of semisolid Mg_(2)Si/AM60 composites prepared by ultrasonic vibration was established.展开更多
基金supported by the Qingdao Jiuhuanxinyue New Energy Technology Co.,Ltd.the Guangdong Basic and Applied Basic Research Foundation(Grant No.2021B1515120071)+2 种基金the 21C Innovation Laboratory,Contemporary Amperex Technology Ltd.(Grant No.21C-OP-202112)the financial support from the Guangdong Basic and Applied Basic Research Foundation(Grant No.2024A1515011873)the Shenzhen Science and Technology Program(Grant No.JCYJ20220531095212027).
文摘Li metal is widely recognized as the desired anode for next-generation energy storage,Li metal batteries,due to its highest theoretical capacity and lowest potential.Nonetheless,it suffers from unstable electrochemical behaviors like dendrite growth and side reactions in practical application.Herein,we report a highly stable anode with collector,Li_(5)Mg@Cu,realized by the melting-rolling process.The Li_(5)Mg@Cu anode delivers ultrahigh cycle stability for 2000 and 1000 h at the current densities of 1 and 2 mA cm^(-2),respectively in symmetric cells.Meanwhile,the Li_(5)Mg@Cu|LFP cell exhibits a high-capacity retention of 91.8% for 1000 cycles and 78.8% for 2000 cycles at 1 C.Moreover,we investigate the suppression effects of Mg on the dendrite growth by studying the performance of Li_(x)Mg@Cu electrodes with different Mg contents(2.0-16.7 at%).The exchange current density,surface energy,Li^(+)diffusion coefficient,and chemical stability of Li_(x)Mg@Cu concretely reveal this improving suppression effect when Mg content becomes higher.In addition,a Mg-rich phase with“hollow brick”morphology forming in the high Mg content Li_(x)Mg@Cu guides the uniform deposition of Li.This study reveals the suppression effects of Mg on Li dendrites growth and offers a perspective for finding the optimal component of Li-Mg alloys.
基金financial support from the National Natural Science Foundation of China(Nos.22276159,J2224005)the Key research project plan for higher education institutions of Henan province(No.24ZX009)+1 种基金the Development Program for Key Young Teachers in Colleges and Universities of Henan Province(No.2020GGJS146)the Starting Research Fund of Xinxiang Medical University(No.XYBSKYZZ201911)。
文摘In this work,atomic Co catalysts are anchored on a three-dimensional(3D)interconnected g-C_(3)N_(4)(SACo-CN)through Co-N coordination,which exhibit efficient charge carrier transition and low activation energy barriers for peroxymonosulfate(PMS).The incorporation of Co atoms extends the absorption spectrum and enhances the photoelectron-hole separation efficiency of the SACo-CN samples.The 3D interconnected structure,combined with the synergistic interplay between Co-N coordination and visible light irradiation,results in SACo-CN catalysts demonstrating excellent catalytic activity and stability for PMS activation.This leads to a degradation rate of 98.8%for oxytetracycline(OTC)within 30 min under visible light.The research proposes three potential mineralization pathways with eight intermediates,leading to a significant decrease in the toxicity of the intermediates.This work provides a facile and promising approach for the preparation of metal single atom catalysts with highly efficient PMS activation performance.
基金supported by the National Natural Science Foundation of China(Nos.22103045 and 52273077)the State Key Laboratory of Bio-Fibers and Eco-Textiles,Qingdao University(Nos.ZDKT202108,RZ2000003334 and G2RC202022)support from the Australian National Fabrication Facility’s Queensland Node(No.ANFF-Q),the UQ-Yonsei International Research Project,and the JST-ERATO Yamauchi Materials Space-Tectonics Project(No.JPMJER2003).
文摘High-entropy metal phosphide(HEMP)has considerable potential as an electrocatalyst owing to its beneficial properties,including high-entropy alloy synergy as well as the controllable structure and high conductivity of phosphides.Herein,electrospinning and in situ phosphating were employed to prepare three-dimensional(3D)networks of self-supporting HEMP nanofibers with varying degrees of phosphate content.Comprehensive characterizations via X-ray diffraction and X-ray photoelectron spectroscopy,as well as density functional theory calculations,demonstrate that the introduction of phosphorus(P)atoms to HEMP carbon nanofibers mediates their electronic structure,leads to lattice expansion,which in turn enhances their catalytic performance in the hydrogen evolution reaction(HER).Moreover,the formation of metal-P bonds weakens metal-metal interaction and decreases the free energy of hydrogen adsorption,contributing to the exceptional activity observed in the HEMP catalyst.Electrochemical measurements demonstrate that the HEMP-0.75 catalyst with an ultralow loading of 1.22 wt%ruthenium(Ru)exhibits the highest HER catalytic activity and stability in a 1 M KOH electrolyte,achieving a minimal overpotential of 26 mV at a current density of 10 mA·cm^(-2)and Tafel slope of 50.9 mV·dec^(-1).
文摘In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool materials and design, tool wea,, processing temperature, material flow, processing window and residual stresses. A particular emphasis is given to microstructural aspects and microstructure-properties relationship. Potential engineering applications are highlighted.
基金financially supported by the National Natural Science Foundation of China(No.51571084)financial support from the China Scholarship Council(No.201908410208)。
文摘Microstructure evolution and dynamic restoration mechanism of solution-treated Mg-4Y-2Nd-1Sm-0.5Zr alloy have been studied under three TMP parameters consisting of deformation temperatures(350-500℃),strain rates(0.01-5 s^(-1)),and strains(0.2,0.4,and 0.8).A strong dynamic softening is observed in all stress-strain curves,even at higher strain rates(1 and 5 s^(-1))due to an adiabatic heating effect.Various stress-strain curves are applied to construct a processing map and develop an Arrhenius-type constitutive equation.With the prediction of the processing map,an optimal processing domain has been determined to be the temperature range 450-500℃and strain rate range 0.01-0.1 s^(-1)at a strain of 0.8.The volume fraction of DRX grains is the largest in the corresponding domain of high temperature and low strain rate.For the effect of TMP parameters on the dynamic restoration,the discontinuous dynamic recrystallization(DDRX)and continuous DRX(CDRX)synergistic effect occur throughout the whole process at high temperature and high strain rate.In terms of high temperature and low strain rate,DDRX characteristics at a low strain and then the DDRX+CDRX synergistic effect is observed at a higher strain.Although the DRX process is weak at low temperature and low strain rate,deformation twins have occurred and provided nucleation sites for DRX grains.
基金JST PRESTO(grant number JPMJPR22Q4)(Japan)The Light Metal Educational Foundation,Inc.(Japan),and“Knowledge Hub Aichi”Aichi Prefectural Government(Japan)The synchrotron radiation experiments were performed at BL46XUof SPring-8with the approval of the Japan Synchrotron Radiation Research Institute(JASRI)(Proposal No.2021A1663,2022A1001and 2022A1798).
文摘The microstructural factors contributing to the high strength of additive-manufactured Al-Si alloys us-ing laser-beam powder bed fusion(PBF-LB)were identified by in-situ synchrotron X-ray diffraction in tensile deformation and transmission electron microscopy.PBF-LB and heat treatment were employed to manufacture Al-12%Si binary alloy specimens with different microstructures.At an early stage of de-formation prior to macroscopic yielding,stress was dominantly partitioned into the α-Al matrix,rather than the Si phase in all specimens.Highly concentrated Si solute(~3%)in the α-Al matrix promoted the dynamic precipitation of nanoscale Si phase during loading,thereby increasing the yield strength.After macroscopic yielding,the partitioned stress in the Si phase monotonically increased in the strain-hardening regime with an increase in the dislocation density in the α-Al matrix.At a later stage of strain hardening,the flow curves of the partitioned stress in the Si phase yielded stress relaxation owing to plastic deformation.Therefore,Si-phase particles localized along the cell walls in the cellular-solidified microstructure play a significant role in dislocation obstacles for strain hardening.Compared with the results of the heat-treated specimens with different microstructural factors,the dominant strengthening factors of PBF-LB manufactured Al-Si alloys were discussed.
基金support from the Australian Research Council(ARC)Linkage Project(LP200200689).
文摘The high cost of using the niobium(Nb)barrier for manufacturing magnesium diboride(MgB2)mono-and multi-filamentary wires for large-scale applications has become one of the barriers to replacing current commercial niobium-titanium superconductors.The potential of replacing the Nb barrier with a low-cost iron(Fe)barrier for multifilament MgB2 superconducting wires is investigated in this manuscript.Therefore,MgB2 wires with Fe barrier sintered with different temperatures are studied(from 650°C to 900°C for 1 h)to investigate the non-superconducting reaction phase of Fe-B.Their superconducting performance including engineering critical current density(Je)and n-value are tested at 4.2 K in various external magnetic fields.The best sample sintered at 650°C for 1 h has achieved a Je value of 3.64×10^(4) A cm^(−2) and an n-value of 61 in 2 T magnetic field due to the reduced formation of Fe2B,better grain connectivity and homogenous microstructure.For microstructural analysis,the focused ion beam(FIB)is utilised for the first time to acquire three-dimensional microstructures and elemental mappings of the interface between the Fe barrier and MgB2 core of different wires.The results have shown that if the sintering temperature can be controlled properly,the Je and n-value of the wire are still acceptable for magnet applications.The formation of Fe2B is identified along the edge of MgB2,as the temperature increases,the content of Fe2B also increases which causes the degradation in the performance of wires.
基金supported by the JSPS fellowship to M.K.M(Grant Number P20039)support from JST-ERATO Yamauchi Materials Space-Tectonics Project(JPMJER2003)+1 种基金the funding from the Queensland government through the Advance Queensland Fellowship Program(AQIRF043-2020-CV)supported by the National Health and Medical Research Council(NHMRC,1195451).
文摘Sweat contains numerous vital biomarkers such as metabolites,electrolytes,proteins,nucleic acids and antigens that reflect hydration status,exhaustion,nutrition,and physiological changes.Conventional healthcare diagnosis relies on disease diagnostics in sophisticated centralized laboratories with invasive sample collection(e.g.,chemical analyses,plasma separation via centrifugation,tissue biopsy,etc.).Cutting-edge point-of-care diagnostics for sweat biomarker analysis allow for non-invasive monitoring of physiologically related biomarkers in sweat and real-time health status tracking.Moreover,using advanced nanoarchitectures,including nanostructured platforms and nanoparticles,can enhance the specificity,sensitivity,wearability and widen the sensing modality of sweat biosensors.Herein,we comprehensively review the secretory mechanisms,clinical uses of sweat biomarkers,and the design,principle,and latest technologies of sweat biosensors.With an emphasis on cutting-edge technologies for sweat biomarker analysis,this review chronicles the issues associated with the current sweat biomarkers analysis of sweat biomarkers and provides insights into strategies for enhancing the translation of such biosensors into routine clinical practice.
基金financial supports received from the National Key Research and Development Program of China(No.2022YFE0109600)the Science and Technology Innovation Program of Hunan Province(No.2024RC3010)the National Natural Science Foundation of China(No.51974376).
文摘The tensile creep anisotropy of a dilute-alloyed Mg-0.3wt%Ca sheet is investigated along the rolling direction(RD)and normal direction(ND).Strong creep anisotropy is shown between the RD and ND,owing to the easy twinning and the Ca-segregation along twin boundaries during creep loading along the ND.To weaken the creep anisotropy,hot-compression parallel to the RD-ND plane is performed and the continuous dynamic recrystallization mechanism induces a bimodal microstructure with the coexistence of unrecrystallized and recrystallized grains.The creep anisotropy is successfully weakened after hot-compression,and the creep resistance is also significantly enhanced along both loading directions.With the assistance of microstructural characterization,the weakened creep anisotropy is ascribed to the dislocation arrays in the interiors of recrystallized grains and the Ca-segregation along the boundaries of recrystallized grains.Compared to commercial Mg alloys with poor creep property and rare-earth alloyed Mg with high price,good creep performance and low production cost can be synchronously realized in the hot-compressed Mg-0.3wt%Ca alloy.Thus,this work proposes a new perspective for producing creep-resistant Mg alloys.
基金supported by the National Natural Science Foundation of China(51364035,51165032)Ministry of Education tied up with the Special Research Fund for the Doctoral Program for Higher School(20133601110001)Loading Program of Science and Technology of College of Jiangxi Province(KJLD14003)
文摘The study systematically investigated the effects of master alloy addition containing rare earth elements La and Yb on the microstructures characteristic and tensile properties of A1Sil0Cu3 alloy. It was studied by means of optical microscopy, X-ray diffraction, scanning electron microscopy, energy diffraction spectnam and differential thermal analyzer. The results showed that the ad-dition of （La＋Yb） obviously reduced the sizes of the primary a-Al phase and eutectic Si particles as well as 13-A15FeSi phase and im- proved the morphology of the primary a-A1 phase and eutectic Si particles. The optimum addition of（La＋Yb） addition was 0.6 wt.%. Comparing the 0.6 wt.% （La＋Yb） modified A1Sil0Cu3 alloy with the unmodified alloy, it was found that the mean diameter, mean area and SADS of primary a-A1 phase were decreased by 50.80%, 75.74% and 50.83% respectively; the aspect ratio, size （length） and mean area of eutectic Si particles were decreased by 66.30%, 81.78% and 78.99%, respectively, and the average size of the β-AlsFeSi phase was 16.4 pro. In addition, the addition of （La＋Yb） greatly improved the tensile properties ofA1Si 10Cu3 alloy, especially in the ultimate tensile strength and elongation as a result of the significant improvement in microstructure.
基金financially supported by the Project of the Science and Technology Creative Team of Universities in Jiangxi Province,China(No.00008713)the Open Foundation of Jiangxi Key Laboratory for Advanced Copper and Tungsten Materials(No.2013-KLP-04)
基金Project supported by National Natural Science Foundation of China(51165032,51364035)the Ministry of Education Tied up with the Special Research Fund for the Doctoral Program for Higher Shool(20133601110001)+2 种基金Innovative Group of Science and Technology of College of Jiangxi Province(00008713)Production and Teaching and Research Cooperation Plan of Nanchang Non-party Experts and Doctor(2012-CYH-DW-XCL-002)Special Funds for Postgraduate Innovation of Jiangxi Province
文摘Abstract： Semi-solid A12Y/AZ91 magnesium matrix composites slurry was prepared by ultrasonic vibration, effect of ultrasonic vi bration temperature and time on microstructure of semi-solid slurry was investigated. The results showed that with the ultrasonic vibration temperature decreasing the solid volume fraction of semi-solid slurry increased. The best ultrasonic vibration temperature was 600 ℃. With the increase of ultrasonic vibration time, the average grain diameter of primary a-Mg particles decreased firstly, then increased, the average shape factor increased gradually and decreased slightly after 90 s, and a few rosette dendrites were observed after 120 s. The best semi-solid slurry with average grain diameter of 75 μm and shape factor of 0.7 were gained after the melt was treated by ultrasonic vibration for about 60 s at near liquidus temperature （600 ℃）. At last, the microstructure evolution mechanism of semi-solid magnesium matrix composites slurry was analyzed by the theories of thermodynamics and kinetics.
基金financially supported by the National Natural Science Foundation of China (No. 51165032)the Innovative Group of Science and Technology of College of Jiangxi Province (No. 00008713)the Jiangxi Province Education Commission Foundation (No. GJJ13203)
文摘In this study, two kinds of Al–La master alloys were prepared by ultrasonic method and ordinary mixmelting method, and both of the alloys were added into the Al alloy.Then, the microstructure of Al–La master alloy and the modification effect on the Al alloy were investigated using optical microscope(OM), X-ray diffraction(XRD), scanning electron microscope(SEM), and energy disperse spectroscopy(EDS).The results show that because of ultrasonic cavitation and streaming, the grain size of Al–La master alloy prepared by the ultrasonic method is refined, which distributes evenly.And, there is no gas hole,inclusion, or segregation in the Al–La master alloy with aAl, La, and La3Al11.Furthermore, Al–La master alloys show a nice modification for Al alloy, which is much better than that prepared by ordinary mix-melting method.
基金supported by the National Natural Science Foundation of China(51364035)
文摘The influence of heat treatment（T6） on the ambient temperature dry sliding wear behavior of the extruded AZ91 alloy treated with Y using a pin-on-disc apparatus was investigated. Wear rates and friction coefficients were measured within a load range of 5-70 N at a sliding speed of 0.188 m/s over a constant sliding distance of 226.195 m. Worn surfaces and debris were examined using a scanning electron microscope equipped with an energy dispersive spectrometer. The experimental results revealed that, as applied load was increased, the alloy wear rates increased, but the friction coefficients decreased. Four chief operating wear mechanisms were observed, i.e., abrasion, oxidation, delamination and plastic deformation. The extruded AZ91 alloy treated with Y exhibited better wear resistance by adopting T6, which was mainly due to large amounts of fine Mg_（17）Al_（12） distributed in the grains and the resulting modified strength and micro-hardness.
基金This work was supported by the National Natural Science Foundation of China under grant No.50234020 and 50475157the Key Project by Ministry of Education of China(No.105052).
文摘The solidification behaviors of AZ61 magnesium alloy under a high magnetic field were studied. The corrosion property of AZ61 alloy was investigated in a solution of 3.5 mol/L NaCI by measuring electrochemical p.olarization. The results show that the high magnetic field can refine microstructure and benefit aluminum transfer. The crystal of α-Mg is induced to orient with their c-axis parallel to the magnetic field. The corrosion studies indicate that different crystal plane of magnesium has different corrosion property. The passivating films on the α- and b-planes have higher corrosion resistance than that on the c-plane. Aligned structure affects the corrosion property of AZ61 magnesium alloy.
基金support of the“Knowledge Hub Aichi”a Priority Research Project of Aichi Prefectural Government,Japan。
文摘To identify the microstructural features of the lattice structures of Al alloys built via the selective laser melting(SLM)process,AlSil OMg alloy with a body-centered cubic(BCC)-type lattice structure was prepared.Characteristic microstructures comprising melt pools with several columnarα-Al phases with<001>orientations along the elongation direction and surrounded by eutectic Si particles were observed at all portions of the built lattice structure.In the node portions of the lattice structure,a gradient microstructure(continuous change in microstructure)was observed.The columnarα-Al phases were observed near the top surface of the node portion,whereas they became coarser and more equiaxed near the bottom surface,resulting in softening localized near the bottom surface.In the strut portions of the lattice structure,the columnarα-Al phases were elongated along the inclined direction of struts.This trend was more prevalent near the bottom surface.Theα-Al phases became coarser and more equiaxed near the bottom surface as well.The aforementioned results were the basis of a discussion of the development of the gradient microstructure in lattice-structured Al alloys during the SLM process in terms of thermal conductivities at the boundaries between the manufactured(locally melted and rapidly solidified)portions and adjacent(unmelted)alloy powder.
文摘The effect of equal-channel angular pressing(ECAP) on the pitting corrosion resistance of anodized Al-Cu alloy was investigated by electrochemical techniques in a solution containing 0.2 mol/L AlCl3 and also by surface analysis.Anodizing was conducted for 20 min at 200 and 400 A/m2 in a solution containing 1.53 mol/L H2SO4 and 0.018 5 mol/L Al2(SO4)3·16H2O at 20 ℃.Anodized Al-Cu alloy was immediately dipped in boiling water for 20 min to seal the micro pores present in anodic oxide films.The time required before initiating pitting corrosion of anodized Al-Cu alloy is longer with ECAP than without,indicating that ECAP process improves the pitting corrosion resistance of anodized Al-Cu alloy.Second phase precipitates such as Si,Al-Cu-Mg and Al-Cu-Si-Fe-Mn intermetallic compounds are present in Al-Cu alloy and the size of these precipitates is greatly decreased by application of ECAP.Al-Cu-Mg intermetallic compounds are dissolved during anodization,whereas the precipitates composed of Si and Al-Cu-Si-Fe-Mn remain in anodic oxide films due to their more noble corrosion potential than Al.FE-SEM and EPMA observation reveal that the pitting corrosion of anodized Al-Cu alloy occurs preferentially around Al-Cu-Si-Fe-Mn intermetallic compounds,since the anodic oxide films are absent at the boundary between the normal oxide films and these impurity precipitates.The improvement of pitting corrosion resistance of anodized Al-Cu alloy processed by ECAP appears to be attributed to a decrease in the size of precipitates,which act as origins of pitting corrosion.
基金financial support from the National Natural Science Foundation of China(Grant no.51571084)financial support from the Grant-in-Aid for Early-Career Scientists(Grant no.18K14024)financial support from the China Scholarship Council(Grant No.201908410208)
文摘We utilized electron backscatter diffraction to investigate the microstructure evolutions of a newly developed magnesium-rare earth alloy(Mg–9.80 Gd–3.78 Y–1.12 Sm–0.48 Zr)during instantaneous hot indirect extrusion.An equiaxed fine-grained(average grain size of 3.4±0.2μm)microstructure with a weak texture was obtained.The grain refinement was mainly attributed to the discontinuous dynamic recrystallization(DDRX)and continuous DRX(CDRX)processes during the hot indirect extrusion process.The twin boundaries formed during the initial deformation stage effectively increased the number of high angle grain boundaries(HAGBs),which provided sites for new grain nuclei,and hence,resulted in an improved DDRX process.Along with DDRX,CDRX processes characterized by low angle grain boundary(LAGB)networks were also observed in the grain interior due to effective dynamic recovery(DRV)at a relatively high temperature of 773 K and high strain rates.Thereafter,LAGB networks were transformed into HAGB networks by the progressive rotation of subgrains during the CDRX process.
基金the financial support from the National Natural Science Foundation of China(No.51571084)the financial support from the Grant-in-Aid for Early-Career Scientists(No.18K14024)financial support from the China Scholarship Council(No.201908410208)。
文摘The deformation mechanism of slips and twins has a considerable influence on the plasticity of magnesium alloys. However, the roles of slips and twins in the room-temperature deformation of Mg-rare earth(Mg-RE) alloys with high contents of rare earth elements is rarely investigated. Here, the microstructural evolution and deformation mechanism of an aged Mg-5 Y-2 Nd-3 Sm-0.5 Zr alloy during uniaxial compression at room temperature were systematically investigated using in-situ electron-backscattered diffraction and transmission electron microscopy. The results indicated that in the early stage of deformation, the Mg-RE alloy was mainly controlled by the slip of dislocations in the basal plane and the coordinated c-axis strain of the {10-12} twin. With an increase in the strain, the grain orientation became more suitable for the initiation of pyramidal Ⅱ dislocations in the later stage of deformation;these dominated the deformation mechanism. In the twin evolution of the Mg-RE alloy, there were three types of twin-twin interaction behaviors:(i) single twin variant 'parallel' structure,(ii) single twin variant 'cross' structure, and(iii) multi twin variant 'cross' structure. In addition, three types of twin-grain boundary interaction behaviors were summarized:(i) twin 'refracting through' grain boundary,(ii) twin'parallel through' grain boundary, and(iii) twin 'fusing through' grain boundary, which are expected to act as new means and solutions for the twin strengthening of magnesium alloys.
基金financially supported by the National Natural Science Foundation of China (Nos.51364035 and 51165032)
文摘The rheological behavior of semisolid Mg_(2)Si/AM60 composites prepared by ultrasonic vibration treatment was investigated.The effects of primaryα-Mg solid content,the ultrasonic power and the content of reinforcement phase Mg_(2)Si on the apparent viscosity of semisolid composites were discussed.The results show that the apparent viscosity of the semis olid composites increases with the increase in a-Mg solid content.Meanwhile,the apparent viscosity decreases with the increase in ultrasonic power,and the reduction amplitude is higher when the solid content is higher.In addition,the apparent viscosity increases with the increase in Mg_(2)Si content.Based on experimental data fitting,the rheological model of semisolid Mg_(2)Si/AM60 composites prepared by ultrasonic vibration was established.
