Essentially, it is significant to supply the consumer with reliable and sufficient power. Since, power quality is measured by the consistency in frequency and power flow between control areas. Thus, in a power system ...Essentially, it is significant to supply the consumer with reliable and sufficient power. Since, power quality is measured by the consistency in frequency and power flow between control areas. Thus, in a power system operation and control,automatic generation control(AGC) plays a crucial role. In this paper, multi-area(Five areas: area 1, area 2, area 3, area 4 and area 5) reheat thermal power systems are considered with proportional-integral-derivative(PID) controller as a supplementary controller. Each area in the investigated power system is equipped with appropriate governor unit, turbine with reheater unit, generator and speed regulator unit. The PID controller parameters are optimized by considering nature bio-inspired firefly algorithm(FFA). The experimental results demonstrated the comparison of the proposed system performance(FFA-PID)with optimized PID controller based genetic algorithm(GAPID) and particle swarm optimization(PSO) technique(PSOPID) for the same investigated power system. The results proved the efficiency of employing the integral time absolute error(ITAE) cost function with one percent step load perturbation(1 % SLP) in area 1. The proposed system based FFA achieved the least settling time compared to using the GA or the PSO algorithms, while, it attained good results with respect to the peak overshoot/undershoot. In addition, the FFA performance is improved with the increased number of iterations which outperformed the other optimization algorithms based controller.展开更多
The microstructure and electrical properties of ZnO-Bi2O3-Yb2O3 based varistor ceramics were investigated with various temperature effects from 900°C to 1050°C.From the results,it was observed that the incre...The microstructure and electrical properties of ZnO-Bi2O3-Yb2O3 based varistor ceramics were investigated with various temperature effects from 900°C to 1050°C.From the results,it was observed that the increase of sintering temperature offers a reduced capacitive effect from 0.460 nF to 0.321 nF.Furthermore,the grain sizes of varistors were varied from 6.8μm to 9.8μm.The consequence of such smaller grain sizes provided a better voltage gradient of about 895 V/mm for the disc sintered at 900°C and fallen drastically to 410 V/mm for the sample sintered at 1050°C.In addition,there was an increase of non-linearity index to a maximum value of 36.0 and reduced leakage current of 0.026 mA/cm2.However,the density of the varistor decreased with an increase of temperature from 5.41 g/cm3 to 5.24 g/cm3.With this base,the influence of varistor capacitance and high voltage gradient were scrutinized and it led an improved transition speed of the varistor assembly from non-conduction to conduction mode during intruding nanosecond transients.展开更多
A physical model for mobility degradation by interface-roughness scattering and Coulomb scattering is proposed for SiGe p-MOSFET with a high-k dielectric/SiO2 gate stack. Impacts of the two kinds of scatterings on mob...A physical model for mobility degradation by interface-roughness scattering and Coulomb scattering is proposed for SiGe p-MOSFET with a high-k dielectric/SiO2 gate stack. Impacts of the two kinds of scatterings on mobility degradation are investigated. Effects of interlayer （SiO2） thickness and permittivities of the high-k dielectric and interlayer on carrier mobility are also discussed. It is shown that a smooth interface between high-k dielectric and interlayer, as well as moderate permittivities of high-k dielectrics, is highly desired to improve carriers mobility while keeping alow equivalent oxide thickness. Simulated results agree reasonably with experimental data.展开更多
Combined cycle plants (CCs) are broadly used all over the world. The inclusion of CCs into the optimal resource scheduling causes difficulties because they can be operated in different operating configuration modes ba...Combined cycle plants (CCs) are broadly used all over the world. The inclusion of CCs into the optimal resource scheduling causes difficulties because they can be operated in different operating configuration modes based on the number of combustion and steam turbines. In this paper a model CCs based on a mixed integer linear programming approach to be included into an optimal short term resource optimization problem is presented. The proposed method allows modeling of CCs in different modes of operation taking into account the non convex operating costs for the different combined cycle mode of operation.展开更多
A very compact (80 - 100 μm2) integrated power splitting devices with two outputs (1 × 2), four outputs (1 × 4) and six outputs (1 × 6) channel has been designed, simulated and optimized for Telecommun...A very compact (80 - 100 μm2) integrated power splitting devices with two outputs (1 × 2), four outputs (1 × 4) and six outputs (1 × 6) channel has been designed, simulated and optimized for Telecommunication purpose with T-Junction, Y-Junction, PC line defect waveguides integrated with multimode interference block (PCLD-MMI) and multiple line defect PC waveguides (MLDPCW) configurations. The optical modeling of these proposed structures was investigated by finite difference time domain (FDTD) simulation. With the optimization of the parameters (Hole Radius, R = 0.128 μm, Input Diameter, D = 1.02 μm, Input wavelength, λ = 1.55 μm, Substrate Reflective Index, nsub = Si(1.52), Photonic Crystal Material, npcs = InAs(3.45), and Rectangular crystal structure), 1 × 2 for Y-Junction (100%), 1 × 4 for T-Junction (92.8%) and 1 × 6 configuration for MLDPCW (81%) show maximum power transmission.展开更多
Considering the geographical location and one of the very densely populated countries in the world, Bangladesh is very vulnerable to climate change and its adaptability. This paper has been designed with an attempt to...Considering the geographical location and one of the very densely populated countries in the world, Bangladesh is very vulnerable to climate change and its adaptability. This paper has been designed with an attempt to inform the policy maker of Bangladesh regarding the potentiality of MSW as a renewable source of energy in Bangladesh. It deals with modern waste collection, management and incineration practices based on densely populated cities or towns like Bogura Municipality and Chattogram City Corporation. Waste to Energy (WtE) conversions not only reduce the land pressure problem in urban areas, but also generate electricity and heat to supply to the surrounding urban areas. The increase in generation of methane (CH<sub>4</sub>) from municipal solid wastes (MSW) alarms the world to take suitable initiative for the sustainable management of MSW, as it is stronger than carbon dioxide (CO<sub>2</sub>). By burning one mole of CH<sub>4</sub>, 890 kJ·mol<sup>-1</sup> heat is produced which is a major source of energy. This treatment technology is used in destruction of solid waste by controlled burning at high temperatures. With the release of heat, it can be accompanied and this heat from combustion can be converted into energy. This type of incineration is a high-quality treatment for Municipal or City Corporation solid waste like Bangladesh where were over crowded cities, towns and it can reduce the quantity and volume of a large amount of waste to landfill, which can recover energy and dispose in the compact zone. The results also examined that the total amount of solid waste produced in Bogura municipality is lower than that of Chattogram City Corporation. The percentage compositions of waste patterns are shown in both the Cities. The paper discusses these problems, analyses and finally, a recommendation has been proposed in order to understand the industrial situation enhanced.展开更多
In a three phase power system, the voltages at the generation side are in sinusoidal and equal in magnitude with 120? phase difference between the phases. However, at the load side voltages may become unbalanced due t...In a three phase power system, the voltages at the generation side are in sinusoidal and equal in magnitude with 120? phase difference between the phases. However, at the load side voltages may become unbalanced due to unequal voltage magnitudes at the fundamental frequency, phase angle deviations or unequal distribution of single phase loads. The voltage unbalance is a major power quality issue, because a small unbalance in the phase voltages can cause a larger unbalance in the phase currents. A completely balanced three-phase three wire system contains only positive sequence components of voltage, current and impedance, whereas unbalanced system contains both positive and negative sequence components of voltages and currents. The negative sequence component of current in the unbalanced system increases the temperature and losses in the equipments. Hence, it is necessary to mitigate this problem by supplying the negative sequence current to the load at the load side and keep the source side balanced. This paper proposes the shunt connected, current injecting Distribution Static Synchronous Compensator (DSTATCOM) with appropriate controller to mitigate the unbalanced load current. The symmetrical components based Hysteresis Current Controller (HCC) is designed for DSTATCOM to diminish the unbalances in a three-phase three-wire system. The performance of the controller is studied by simulating the entire system in the MATLAB/Simulink environment. The DSTATCOM with HCC is found to be better than other controllers because it is suitable for compensating both balanced and unbalanced loads.展开更多
Two acetylene polymers containing cyanobiphenyl-based mesogens, poly{10-[((4'-cyano-4-biphenylyl)oxy)carbonyl]-1-decyne} (PA8CN), which has a relatively flexible polyalkyne backbone, and poly {[4-(((12-((4'-cy...Two acetylene polymers containing cyanobiphenyl-based mesogens, poly{10-[((4'-cyano-4-biphenylyl)oxy)carbonyl]-1-decyne} (PA8CN), which has a relatively flexible polyalkyne backbone, and poly {[4-(((12-((4'-cyano-4-biphenylyl)oxy)dodecyl)oxy) carbonyl) phenyl]-acetylene} (PB12CN), which has a fairly rigid poly(phenylacetylene) backbone, were synthesized using respectively WCl6 and [Rh(nbd)Cl](2) as the catalysts. PA8CN exhibits enantiotropic interdigitated smectic A phase (S-Ad) over a temperature range as wide as ca. 100 degrees C, whereas PB12CN is non-mesomorphic, demonstrating that the backbone rigidity plays an important role in determining the liquid crystallinity of the polyacetylenes.展开更多
Effects of the intergrain exchange interaction on magnetic properties of nanocomposite magnets were investigated by using the computer simulation based on the micromagnetic theory. The simulation was carried out unde...Effects of the intergrain exchange interaction on magnetic properties of nanocomposite magnets were investigated by using the computer simulation based on the micromagnetic theory. The simulation was carried out under the assumptions that the strength of the intergrain exchange interaction is weaker than that of the intragrain exchange interaction, that inhomogeneous nanostructures result in the distribution of the strength of the intergrain exchange interaction, and that there exists nonmagnetic intergranular phase (NMIP) between grain boundaries. The distribution of the strength of the intergrain exchange interaction was simulated by the lognormal distribution with the standard deviation of σ.The calculations for Nd 2Fe 14B/α-Fe nanocomposite magnets reveal that a suitably weak intergrain exchange interaction and small grain size enable us to improve magnetic properties. It is also found that a Nd 2Fe 14B/α-Fe nanocomposite magnet has a potential of a (BH) max value exceeding 300 kJ·m -3. On the other hand, the calculations for Nd 2Fe 14B/Fe 3B nanocomposite magnets reveal that the distribution of the strength of the intergrain exchange interaction deteriorates magnetic properties significantly. Particularly, this tendency is remarkable, when the grain size L is larger than its optimum value, 11 nm. The existence of nonmagnetic boundary layers accelerats this tendency. At σ=0.2, the calculated demagnetization curve for the model magnet composed of Nd 2Fe 14B(36%)/Fe 3B(54%)/NMIP(10%) (Valume fraction) grains (L=15 nm) agrees with that obtained experimentally for a Nd 2Fe 14B/Fe 3B nanocomposite magnet. These results suggest importance of refinement of grain size, suppression of a nonmagnetic intergranular phase, and preparation of homogeneous nanostructure for superior magnetic properties.展开更多
Per capita electricity consumption of Bangladesh is 400 KWh. Of the total population of 160 million, only 40 percent has the access of using electricity. Dhaka city consumes about 40 - 45 percent of the total electric...Per capita electricity consumption of Bangladesh is 400 KWh. Of the total population of 160 million, only 40 percent has the access of using electricity. Dhaka city consumes about 40 - 45 percent of the total electricity generation of the country. This study reports the trend of electricity use in the Dhaka city with emphasis on the impact of changing temperature due to urbanization and weather change. Hourly data of electricity demand of Dhaka city and the temperature profile of the city for a period of thirty months have been used for this study. To relate weather data like temperature, humidity, wind speed, wind direction, atmospheric pressure, dew point and visibility etc. with electricity demand of the city about 16,508 data between 2011 and 2017 have been considered. A statistical regression has been done to establish a relation between them. From this study it is found that reduction of only 1°C air temperature could save 81 MV of electricity consumption in Dhaka city. A time series forecast has been done to estimate probable temperature change and subsequent electricity consumption up to year 2020. From the study it has been established that the temperature dependence of electricity consumption in Dhaka city is about 75%.展开更多
This paper represents the performance analysis of the different shapes of antenna balun and feeding techniques for step constant tapered slot antenna. This work also addresses the benefits of antenna balun (circular a...This paper represents the performance analysis of the different shapes of antenna balun and feeding techniques for step constant tapered slot antenna. This work also addresses the benefits of antenna balun (circular and rectangular) along with two types of feeding techniques (Microstrip line L-shape and Microstrip line I-shape). The performance of the antenna for each technique is thoroughly investigated using Computer Simulation Technology (CST) Microwave Studio software simulation under the resonant frequency of 5.9 GHz. Results demonstrate that the proposed model is an effective tool for improving antenna performance. Moreover, an extensive comparison has been carried out between the two different shapes, with and without antenna balun and between two feeding techniques focusing on return losses, gain, directivity, and voltage standing wave ratio (VSWR).展开更多
The demand for water pumping in urban water supply and irrigation in Bangladesh is significantly influenced by electricity deficits and high diesel costs. To address these challenges, the adoption of solar power for w...The demand for water pumping in urban water supply and irrigation in Bangladesh is significantly influenced by electricity deficits and high diesel costs. To address these challenges, the adoption of solar power for water pumping emerges as a viable alternative to traditional systems reliant on grid power and diesel. In recent years, there has been a growing emphasis on clean and renewable energies, aligning with the environmental and economic priorities of Bangladesh. The agricultural sector, serving as the backbone of the country’s economy, witnesses an escalating demand for water as the population increases. The extraction and transfer of water for agricultural and drinking purposes translate to high-energy consumption. Leveraging the abundant and essentially free solar energy, particularly during the crop growth periods when irrigation is crucial, presents an optimal solution. This study underscores the underutilization of this vital resource in Bangladesh and advocates for the widespread implementation of solar energy conversion programs, specifically in photovoltaic pumping systems. By comparing these systems with conventional diesel pumps, this paper aims to inspire policymakers, statesmen, and industry professionals to integrate green energy into the water sector. The envisioned outcome is a strategic shift towards sustainable development, with a focus on harnessing solar power to pump water for villages and agriculture, thus contributing to economic and environmental sustainability.展开更多
In copper oxide (CuO) based solar cells, various buffer layers such as CdS, In<sub>2</sub>S<sub>3</sub>, WS<sub>2</sub> and IGZO have been investigated by solar cell capacitance sim...In copper oxide (CuO) based solar cells, various buffer layers such as CdS, In<sub>2</sub>S<sub>3</sub>, WS<sub>2</sub> and IGZO have been investigated by solar cell capacitance simulator (SCAPS) in this work. By varying absorber and buffer layer thickness, photovoltaic parameters (open circuit voltage, fill factor, short-circuit current density and efficiency) are determined. The highest efficiency achieved is 19.6% with WS<sub>2</sub> buffer layer. The impact of temperature on all CuO-based solar cells is also investigated.展开更多
As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties a...As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb<sub>2</sub>Se<sub>3</sub> thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.展开更多
This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. Th...This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. The energy storage elements incorporated in the SEPIC converter possess parasitic resistances. Although ideal components significantly simplifies model development, but neglecting the parasitic effects in models may sometimes lead to failure in predicting first scale stability and actual performance. Therefore, the effects of parasitics have been taken into consideration for improving the model accuracy, stability, robustness and dynamic performance analysis of the converter. Detail mathematical model of SEPIC converter including inductive parasitic has been developed. The performance of the converter in tracking MPP at different irradiance levels has been analyzed for variation in parasitic resistance. The converter efficiency has been found above 83% for insolation level of 600 W/m2 when the parasitic resistance in the energy storage element has been ignored. However, as the parasitic resistance of both of the inductor has increased to 1 ohm, a fraction of the power managed by the converter has dissipated;as a result the efficiency of the converter has reduced to 78% for the same insolation profile. Although the increasing value of the parasitic has assisted the converter to converge quickly to reach the maximum power point. Furthermore it has also been observed that the peak to peak load current ripple is reduced. The obtained simulation results have validated the competent of the MPPT converter model.展开更多
The interconnection of Solar PV to the Tarkwa Bulk Supply Point (BSP) has become necessary in order to provide additional capacity to meet the ever-increasing demand of Tarkwa and its environs during the day. The Sola...The interconnection of Solar PV to the Tarkwa Bulk Supply Point (BSP) has become necessary in order to provide additional capacity to meet the ever-increasing demand of Tarkwa and its environs during the day. The Solar PV Plant will support the Tarkwa BSP during the day. In this study, a grid impact analysis for the integration of Solar PV plant at three points of common coupling (PCC) at Tarkwa Bulk Supply Point’s (BSP) 33 kV network of the Electricity Company of Ghana was carried out. The three PCCs were Tarkwa BSP, Ghana Australia Gold (GAG) Substation and Darmang Substation. Simulations and detailed analysis were carried out with the use of CYME Software (Cyme 8.0 Rev 05). The Solar PV was integrated at varying penetration levels of 9 MWp, 11 MWp, 14 MWp, 16 MWp, 18 MWp, 20 MWp and 23 MWp (representing penetration levels of 40%, 50%, 60%, 70%, 80%, 90% and 100%, respectively) of the 2020 projected light demand of Tarkwa BSP 25.15 MVA network at an average power factor of 0.903. From the study, the optimum capacity of Solar PV power that could be connected is 9 MWp at an optimum inverter power factor of 0.94 lagging, and the GAG Substation was identified as the optimal location. The stiffness ratio at the optimal location was determined as 41.9, a figure which is far greater than the minimum standard value of 5, and gives an indication of very little voltage control problems in the operation of the proposed Solar PV interconnection. The integration of the optimum 9 MW Solar PV Plant to the Tarkwa network represents an additional 12.77% capacity, decreased the technical losses by 7.76%, and increased the voltage profile by 1.97%.展开更多
Rotor flux and torque of an induction motor (IM) are decoupled to obtain performance of DC motor. The decoupling strategy has been developed in terms of stator current components where the core loss is neglected. Many...Rotor flux and torque of an induction motor (IM) are decoupled to obtain performance of DC motor. The decoupling strategy has been developed in terms of stator current components where the core loss is neglected. Many different controllers including fuzzy logic controller (FLC) with neglecting core loss have been designed to control the speed of induction motor. The outcome of investigation about the effect of core loss on indirect field oriented control (IFOC) has been concluded that the actual flux and torque are not reached to the reference flux and torque if core loss is neglected. Thus, the purpose of this paper is to propose a fuzzy logic speed controller of induction motor where flux and torque decoupling strategy is decoupled in terms of magnetizing current instead of stator current to alleviate the effects of core loss. The performances of proposed fuzzy-logic-based controller have been verified by computer simulation. The simulation of speed control of IM using PI and FLC are performed. The simulation study for high-performance control of IM drive shows the superiority of the proposed fuzzy logic controller over the conventional PI controller.展开更多
In this paper, we analyze unsteady two dimensional hydromagnetic forced convection boundary layer flow of a viscous incompressible fluid along flat plates with thermophoresis. The potential flow velocity has been take...In this paper, we analyze unsteady two dimensional hydromagnetic forced convection boundary layer flow of a viscous incompressible fluid along flat plates with thermophoresis. The potential flow velocity has been taken as a function of the distance x and time t. The governing partial differential equations are transformed to ordinary differential equation by applying local similarity transformation. The resulting similarity equations are then solved numerically for unsteady case, applying Nachtsheim-Swigert shooting iteration technique with six order Runge-Kutta method. The variations in fluid velocity, fluid temperature and species concentration are displayed graphically and discussed for different material parameters entering into the analysis. The effects of the pertinent parameters on the skin-friction coefficient, wall heat transfer coefficient and wall deposition flux rate are also displayed in tabulated form and discussed them from the physical point of view. An analysis of the obtained results shows that the flow field is influenced appreciably by the magnetic field parameter and the thermophoresis particle deposition.展开更多
In the textile industry, cotton is the most popular choice among all the natural fibers due to its unique properties such as softness, affinity to skin, biodegradability, absorbency, and moisture being comfortable to ...In the textile industry, cotton is the most popular choice among all the natural fibers due to its unique properties such as softness, affinity to skin, biodegradability, absorbency, and moisture being comfortable to wear. Zinc Oxide Nanoparticles (ZnO NPs) were produced and coated on cotton fabrics. The concentration of Zinc acetate was varied. 2-methoxy-ethanol has been used as a solvent. Using the dip coating technique, ZnO NPs have been coated on the cotton fabric in different mole concentrations. Scanning Electron Microscopy (SEM), Ultraviolet Visible (UV-VIS) spectroscopy, the antifungal and antibacterial activity of the ZnO NPs was performed on the coated fabrics. The SEM images depicted that the nanoparticles are well dispersed on the fabric at 3M concentration of ZnO solution. It was found that the UV absorbance increases with the increase of concentration up to 2M concentration and after that it decreases. It was also found that maximum antibacterial and antifungal activity is at 2M concentration.展开更多
文摘Essentially, it is significant to supply the consumer with reliable and sufficient power. Since, power quality is measured by the consistency in frequency and power flow between control areas. Thus, in a power system operation and control,automatic generation control(AGC) plays a crucial role. In this paper, multi-area(Five areas: area 1, area 2, area 3, area 4 and area 5) reheat thermal power systems are considered with proportional-integral-derivative(PID) controller as a supplementary controller. Each area in the investigated power system is equipped with appropriate governor unit, turbine with reheater unit, generator and speed regulator unit. The PID controller parameters are optimized by considering nature bio-inspired firefly algorithm(FFA). The experimental results demonstrated the comparison of the proposed system performance(FFA-PID)with optimized PID controller based genetic algorithm(GAPID) and particle swarm optimization(PSO) technique(PSOPID) for the same investigated power system. The results proved the efficiency of employing the integral time absolute error(ITAE) cost function with one percent step load perturbation(1 % SLP) in area 1. The proposed system based FFA achieved the least settling time compared to using the GA or the PSO algorithms, while, it attained good results with respect to the peak overshoot/undershoot. In addition, the FFA performance is improved with the increased number of iterations which outperformed the other optimization algorithms based controller.
文摘The microstructure and electrical properties of ZnO-Bi2O3-Yb2O3 based varistor ceramics were investigated with various temperature effects from 900°C to 1050°C.From the results,it was observed that the increase of sintering temperature offers a reduced capacitive effect from 0.460 nF to 0.321 nF.Furthermore,the grain sizes of varistors were varied from 6.8μm to 9.8μm.The consequence of such smaller grain sizes provided a better voltage gradient of about 895 V/mm for the disc sintered at 900°C and fallen drastically to 410 V/mm for the sample sintered at 1050°C.In addition,there was an increase of non-linearity index to a maximum value of 36.0 and reduced leakage current of 0.026 mA/cm2.However,the density of the varistor decreased with an increase of temperature from 5.41 g/cm3 to 5.24 g/cm3.With this base,the influence of varistor capacitance and high voltage gradient were scrutinized and it led an improved transition speed of the varistor assembly from non-conduction to conduction mode during intruding nanosecond transients.
基金Project supported by the National Natural Science Foundation of China （Grant No 60776016）, the RGC of HKSAR, China （Grant No HKU7142/05E）, and Open Foundation of State Key Laboratory of Advanced Technology for Materials Synthesis and Processing （Grant No WUT2006M02）.
文摘A physical model for mobility degradation by interface-roughness scattering and Coulomb scattering is proposed for SiGe p-MOSFET with a high-k dielectric/SiO2 gate stack. Impacts of the two kinds of scatterings on mobility degradation are investigated. Effects of interlayer （SiO2） thickness and permittivities of the high-k dielectric and interlayer on carrier mobility are also discussed. It is shown that a smooth interface between high-k dielectric and interlayer, as well as moderate permittivities of high-k dielectrics, is highly desired to improve carriers mobility while keeping alow equivalent oxide thickness. Simulated results agree reasonably with experimental data.
文摘Combined cycle plants (CCs) are broadly used all over the world. The inclusion of CCs into the optimal resource scheduling causes difficulties because they can be operated in different operating configuration modes based on the number of combustion and steam turbines. In this paper a model CCs based on a mixed integer linear programming approach to be included into an optimal short term resource optimization problem is presented. The proposed method allows modeling of CCs in different modes of operation taking into account the non convex operating costs for the different combined cycle mode of operation.
文摘A very compact (80 - 100 μm2) integrated power splitting devices with two outputs (1 × 2), four outputs (1 × 4) and six outputs (1 × 6) channel has been designed, simulated and optimized for Telecommunication purpose with T-Junction, Y-Junction, PC line defect waveguides integrated with multimode interference block (PCLD-MMI) and multiple line defect PC waveguides (MLDPCW) configurations. The optical modeling of these proposed structures was investigated by finite difference time domain (FDTD) simulation. With the optimization of the parameters (Hole Radius, R = 0.128 μm, Input Diameter, D = 1.02 μm, Input wavelength, λ = 1.55 μm, Substrate Reflective Index, nsub = Si(1.52), Photonic Crystal Material, npcs = InAs(3.45), and Rectangular crystal structure), 1 × 2 for Y-Junction (100%), 1 × 4 for T-Junction (92.8%) and 1 × 6 configuration for MLDPCW (81%) show maximum power transmission.
文摘Considering the geographical location and one of the very densely populated countries in the world, Bangladesh is very vulnerable to climate change and its adaptability. This paper has been designed with an attempt to inform the policy maker of Bangladesh regarding the potentiality of MSW as a renewable source of energy in Bangladesh. It deals with modern waste collection, management and incineration practices based on densely populated cities or towns like Bogura Municipality and Chattogram City Corporation. Waste to Energy (WtE) conversions not only reduce the land pressure problem in urban areas, but also generate electricity and heat to supply to the surrounding urban areas. The increase in generation of methane (CH<sub>4</sub>) from municipal solid wastes (MSW) alarms the world to take suitable initiative for the sustainable management of MSW, as it is stronger than carbon dioxide (CO<sub>2</sub>). By burning one mole of CH<sub>4</sub>, 890 kJ·mol<sup>-1</sup> heat is produced which is a major source of energy. This treatment technology is used in destruction of solid waste by controlled burning at high temperatures. With the release of heat, it can be accompanied and this heat from combustion can be converted into energy. This type of incineration is a high-quality treatment for Municipal or City Corporation solid waste like Bangladesh where were over crowded cities, towns and it can reduce the quantity and volume of a large amount of waste to landfill, which can recover energy and dispose in the compact zone. The results also examined that the total amount of solid waste produced in Bogura municipality is lower than that of Chattogram City Corporation. The percentage compositions of waste patterns are shown in both the Cities. The paper discusses these problems, analyses and finally, a recommendation has been proposed in order to understand the industrial situation enhanced.
文摘In a three phase power system, the voltages at the generation side are in sinusoidal and equal in magnitude with 120? phase difference between the phases. However, at the load side voltages may become unbalanced due to unequal voltage magnitudes at the fundamental frequency, phase angle deviations or unequal distribution of single phase loads. The voltage unbalance is a major power quality issue, because a small unbalance in the phase voltages can cause a larger unbalance in the phase currents. A completely balanced three-phase three wire system contains only positive sequence components of voltage, current and impedance, whereas unbalanced system contains both positive and negative sequence components of voltages and currents. The negative sequence component of current in the unbalanced system increases the temperature and losses in the equipments. Hence, it is necessary to mitigate this problem by supplying the negative sequence current to the load at the load side and keep the source side balanced. This paper proposes the shunt connected, current injecting Distribution Static Synchronous Compensator (DSTATCOM) with appropriate controller to mitigate the unbalanced load current. The symmetrical components based Hysteresis Current Controller (HCC) is designed for DSTATCOM to diminish the unbalances in a three-phase three-wire system. The performance of the controller is studied by simulating the entire system in the MATLAB/Simulink environment. The DSTATCOM with HCC is found to be better than other controllers because it is suitable for compensating both balanced and unbalanced loads.
基金This work was in part supported by the Hong Kong RGC grants HKUST597/95P and HKUST6149/97P.
文摘Two acetylene polymers containing cyanobiphenyl-based mesogens, poly{10-[((4'-cyano-4-biphenylyl)oxy)carbonyl]-1-decyne} (PA8CN), which has a relatively flexible polyalkyne backbone, and poly {[4-(((12-((4'-cyano-4-biphenylyl)oxy)dodecyl)oxy) carbonyl) phenyl]-acetylene} (PB12CN), which has a fairly rigid poly(phenylacetylene) backbone, were synthesized using respectively WCl6 and [Rh(nbd)Cl](2) as the catalysts. PA8CN exhibits enantiotropic interdigitated smectic A phase (S-Ad) over a temperature range as wide as ca. 100 degrees C, whereas PB12CN is non-mesomorphic, demonstrating that the backbone rigidity plays an important role in determining the liquid crystallinity of the polyacetylenes.
文摘Effects of the intergrain exchange interaction on magnetic properties of nanocomposite magnets were investigated by using the computer simulation based on the micromagnetic theory. The simulation was carried out under the assumptions that the strength of the intergrain exchange interaction is weaker than that of the intragrain exchange interaction, that inhomogeneous nanostructures result in the distribution of the strength of the intergrain exchange interaction, and that there exists nonmagnetic intergranular phase (NMIP) between grain boundaries. The distribution of the strength of the intergrain exchange interaction was simulated by the lognormal distribution with the standard deviation of σ.The calculations for Nd 2Fe 14B/α-Fe nanocomposite magnets reveal that a suitably weak intergrain exchange interaction and small grain size enable us to improve magnetic properties. It is also found that a Nd 2Fe 14B/α-Fe nanocomposite magnet has a potential of a (BH) max value exceeding 300 kJ·m -3. On the other hand, the calculations for Nd 2Fe 14B/Fe 3B nanocomposite magnets reveal that the distribution of the strength of the intergrain exchange interaction deteriorates magnetic properties significantly. Particularly, this tendency is remarkable, when the grain size L is larger than its optimum value, 11 nm. The existence of nonmagnetic boundary layers accelerats this tendency. At σ=0.2, the calculated demagnetization curve for the model magnet composed of Nd 2Fe 14B(36%)/Fe 3B(54%)/NMIP(10%) (Valume fraction) grains (L=15 nm) agrees with that obtained experimentally for a Nd 2Fe 14B/Fe 3B nanocomposite magnet. These results suggest importance of refinement of grain size, suppression of a nonmagnetic intergranular phase, and preparation of homogeneous nanostructure for superior magnetic properties.
文摘Per capita electricity consumption of Bangladesh is 400 KWh. Of the total population of 160 million, only 40 percent has the access of using electricity. Dhaka city consumes about 40 - 45 percent of the total electricity generation of the country. This study reports the trend of electricity use in the Dhaka city with emphasis on the impact of changing temperature due to urbanization and weather change. Hourly data of electricity demand of Dhaka city and the temperature profile of the city for a period of thirty months have been used for this study. To relate weather data like temperature, humidity, wind speed, wind direction, atmospheric pressure, dew point and visibility etc. with electricity demand of the city about 16,508 data between 2011 and 2017 have been considered. A statistical regression has been done to establish a relation between them. From this study it is found that reduction of only 1°C air temperature could save 81 MV of electricity consumption in Dhaka city. A time series forecast has been done to estimate probable temperature change and subsequent electricity consumption up to year 2020. From the study it has been established that the temperature dependence of electricity consumption in Dhaka city is about 75%.
文摘This paper represents the performance analysis of the different shapes of antenna balun and feeding techniques for step constant tapered slot antenna. This work also addresses the benefits of antenna balun (circular and rectangular) along with two types of feeding techniques (Microstrip line L-shape and Microstrip line I-shape). The performance of the antenna for each technique is thoroughly investigated using Computer Simulation Technology (CST) Microwave Studio software simulation under the resonant frequency of 5.9 GHz. Results demonstrate that the proposed model is an effective tool for improving antenna performance. Moreover, an extensive comparison has been carried out between the two different shapes, with and without antenna balun and between two feeding techniques focusing on return losses, gain, directivity, and voltage standing wave ratio (VSWR).
文摘The demand for water pumping in urban water supply and irrigation in Bangladesh is significantly influenced by electricity deficits and high diesel costs. To address these challenges, the adoption of solar power for water pumping emerges as a viable alternative to traditional systems reliant on grid power and diesel. In recent years, there has been a growing emphasis on clean and renewable energies, aligning with the environmental and economic priorities of Bangladesh. The agricultural sector, serving as the backbone of the country’s economy, witnesses an escalating demand for water as the population increases. The extraction and transfer of water for agricultural and drinking purposes translate to high-energy consumption. Leveraging the abundant and essentially free solar energy, particularly during the crop growth periods when irrigation is crucial, presents an optimal solution. This study underscores the underutilization of this vital resource in Bangladesh and advocates for the widespread implementation of solar energy conversion programs, specifically in photovoltaic pumping systems. By comparing these systems with conventional diesel pumps, this paper aims to inspire policymakers, statesmen, and industry professionals to integrate green energy into the water sector. The envisioned outcome is a strategic shift towards sustainable development, with a focus on harnessing solar power to pump water for villages and agriculture, thus contributing to economic and environmental sustainability.
文摘In copper oxide (CuO) based solar cells, various buffer layers such as CdS, In<sub>2</sub>S<sub>3</sub>, WS<sub>2</sub> and IGZO have been investigated by solar cell capacitance simulator (SCAPS) in this work. By varying absorber and buffer layer thickness, photovoltaic parameters (open circuit voltage, fill factor, short-circuit current density and efficiency) are determined. The highest efficiency achieved is 19.6% with WS<sub>2</sub> buffer layer. The impact of temperature on all CuO-based solar cells is also investigated.
文摘As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb<sub>2</sub>Se<sub>3</sub> thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.
文摘This paper presents an analysis of the effect of parasitic resistances on the performance of DC-DC Single Ended Pri- mary Inductor Converter (SEPIC) in photovoltaic maximum power point tracking (MPPT) applications. The energy storage elements incorporated in the SEPIC converter possess parasitic resistances. Although ideal components significantly simplifies model development, but neglecting the parasitic effects in models may sometimes lead to failure in predicting first scale stability and actual performance. Therefore, the effects of parasitics have been taken into consideration for improving the model accuracy, stability, robustness and dynamic performance analysis of the converter. Detail mathematical model of SEPIC converter including inductive parasitic has been developed. The performance of the converter in tracking MPP at different irradiance levels has been analyzed for variation in parasitic resistance. The converter efficiency has been found above 83% for insolation level of 600 W/m2 when the parasitic resistance in the energy storage element has been ignored. However, as the parasitic resistance of both of the inductor has increased to 1 ohm, a fraction of the power managed by the converter has dissipated;as a result the efficiency of the converter has reduced to 78% for the same insolation profile. Although the increasing value of the parasitic has assisted the converter to converge quickly to reach the maximum power point. Furthermore it has also been observed that the peak to peak load current ripple is reduced. The obtained simulation results have validated the competent of the MPPT converter model.
文摘The interconnection of Solar PV to the Tarkwa Bulk Supply Point (BSP) has become necessary in order to provide additional capacity to meet the ever-increasing demand of Tarkwa and its environs during the day. The Solar PV Plant will support the Tarkwa BSP during the day. In this study, a grid impact analysis for the integration of Solar PV plant at three points of common coupling (PCC) at Tarkwa Bulk Supply Point’s (BSP) 33 kV network of the Electricity Company of Ghana was carried out. The three PCCs were Tarkwa BSP, Ghana Australia Gold (GAG) Substation and Darmang Substation. Simulations and detailed analysis were carried out with the use of CYME Software (Cyme 8.0 Rev 05). The Solar PV was integrated at varying penetration levels of 9 MWp, 11 MWp, 14 MWp, 16 MWp, 18 MWp, 20 MWp and 23 MWp (representing penetration levels of 40%, 50%, 60%, 70%, 80%, 90% and 100%, respectively) of the 2020 projected light demand of Tarkwa BSP 25.15 MVA network at an average power factor of 0.903. From the study, the optimum capacity of Solar PV power that could be connected is 9 MWp at an optimum inverter power factor of 0.94 lagging, and the GAG Substation was identified as the optimal location. The stiffness ratio at the optimal location was determined as 41.9, a figure which is far greater than the minimum standard value of 5, and gives an indication of very little voltage control problems in the operation of the proposed Solar PV interconnection. The integration of the optimum 9 MW Solar PV Plant to the Tarkwa network represents an additional 12.77% capacity, decreased the technical losses by 7.76%, and increased the voltage profile by 1.97%.
文摘Rotor flux and torque of an induction motor (IM) are decoupled to obtain performance of DC motor. The decoupling strategy has been developed in terms of stator current components where the core loss is neglected. Many different controllers including fuzzy logic controller (FLC) with neglecting core loss have been designed to control the speed of induction motor. The outcome of investigation about the effect of core loss on indirect field oriented control (IFOC) has been concluded that the actual flux and torque are not reached to the reference flux and torque if core loss is neglected. Thus, the purpose of this paper is to propose a fuzzy logic speed controller of induction motor where flux and torque decoupling strategy is decoupled in terms of magnetizing current instead of stator current to alleviate the effects of core loss. The performances of proposed fuzzy-logic-based controller have been verified by computer simulation. The simulation of speed control of IM using PI and FLC are performed. The simulation study for high-performance control of IM drive shows the superiority of the proposed fuzzy logic controller over the conventional PI controller.
文摘In this paper, we analyze unsteady two dimensional hydromagnetic forced convection boundary layer flow of a viscous incompressible fluid along flat plates with thermophoresis. The potential flow velocity has been taken as a function of the distance x and time t. The governing partial differential equations are transformed to ordinary differential equation by applying local similarity transformation. The resulting similarity equations are then solved numerically for unsteady case, applying Nachtsheim-Swigert shooting iteration technique with six order Runge-Kutta method. The variations in fluid velocity, fluid temperature and species concentration are displayed graphically and discussed for different material parameters entering into the analysis. The effects of the pertinent parameters on the skin-friction coefficient, wall heat transfer coefficient and wall deposition flux rate are also displayed in tabulated form and discussed them from the physical point of view. An analysis of the obtained results shows that the flow field is influenced appreciably by the magnetic field parameter and the thermophoresis particle deposition.
文摘In the textile industry, cotton is the most popular choice among all the natural fibers due to its unique properties such as softness, affinity to skin, biodegradability, absorbency, and moisture being comfortable to wear. Zinc Oxide Nanoparticles (ZnO NPs) were produced and coated on cotton fabrics. The concentration of Zinc acetate was varied. 2-methoxy-ethanol has been used as a solvent. Using the dip coating technique, ZnO NPs have been coated on the cotton fabric in different mole concentrations. Scanning Electron Microscopy (SEM), Ultraviolet Visible (UV-VIS) spectroscopy, the antifungal and antibacterial activity of the ZnO NPs was performed on the coated fabrics. The SEM images depicted that the nanoparticles are well dispersed on the fabric at 3M concentration of ZnO solution. It was found that the UV absorbance increases with the increase of concentration up to 2M concentration and after that it decreases. It was also found that maximum antibacterial and antifungal activity is at 2M concentration.
