This paper presents a proposal for an experimental salt cavern in offshore ultra-deep water for CO2 abatement,including the instrumentation plan and well conceptual design evaluated for carbon capture and storage(CCS)...This paper presents a proposal for an experimental salt cavern in offshore ultra-deep water for CO2 abatement,including the instrumentation plan and well conceptual design evaluated for carbon capture and storage(CCS)application.These studies are based on applied computational mechanics associated with field experimentation that has contributed to the technical feasibility of the underground potash mine at the State of Sergipe in Brazil.This knowhow allowed the stability analysis of several salt caverns for brine production at the State of Alagoas in Brazil and to the drilling through stratified thick layers of salt of the pre-salt reservoirs in Santos Basin.Now,this knowledge has been applied in the design of onshore and offshore salt caverns opened by dissolution for storage of natural gas and CO2.The geomechanical study,through the application of computational mechanics,of offshore giant salt caverns of 450 m high by 150 m in diameter,shows that one cavern can store about 4 billion Sm3 or 7.2 million tons of CO2.Before the construction of the giant cavern,which will be the first gas storage offshore in the world,it has been decided to develop an experimental one,with smaller size,to obtained field parameters.The experimental cavern will allow the calibration of parameters to be used in the structural integrity analysis of the cavern and well for storage of natural gas which is rich in CO2 under high pressure.展开更多
In this study,a coupled tide-surge-wave model was developed and applied to the South Yellow Sea.The coupled model simulated the evolution of storm surges and waves caused by extreme weather events,such as tropical cyc...In this study,a coupled tide-surge-wave model was developed and applied to the South Yellow Sea.The coupled model simulated the evolution of storm surges and waves caused by extreme weather events,such as tropical cyclones,cold waves,extratropical cyclones coupled with a cold wave,and tropical cyclones coupled with a cold wave.The modeled surge level and significant wave height matched the measured data well.Simulation results of the typhoon with different intensities revealed that the radius to the maximum wind speed of a typhoon with 1.5 times wind speed decreased,and its influence range was farther away from the Jiangsu coastal region;moreover,the impact on surge levels was weakened.Thereafter,eight hypothetical typhoons based on Typhoon Chan-hom were designed to investigate the effects of varying typhoon tracks on the extreme value and spatial distribution of storm surges in the offshore area of Jiangsu Province.The typhoon along path 2 mainly affected the Rudong coast,and the topography of the Rudong coast was conducive to the increase in surge level.Therefore,the typhoon along path 2 induced the largest surge level,which reached up to 2.91 m in the radial sand ridge area.The maximum surge levels in the Haizhou Bay area and the middle straight coastline area reached up to 2.37 and 2.08 m,respectively.In terms of typhoons active in offshore areas,the radial sand ridge area was most likely to be threatened by typhoon-induced storm surges.展开更多
According to the existing problems of liquefaction models of saturated sand that were put forward under dynamic action,on the basis of Handin-Drnevich model,a new calculating model of the dynamic constitutive relation...According to the existing problems of liquefaction models of saturated sand that were put forward under dynamic action,on the basis of Handin-Drnevich model,a new calculating model of the dynamic constitutive relation of saturated sand was put forward.The model was based on the basic hypothesis of instantaneous limit balance according to the basic principle that the stress estate is the destroyed condition was not overstepped.The calculated method of increment nonlinear was referenced and combined with the excellence of the model of distributed particles.The process of vibrating liquefaction of saturated sand was divided into some areas.And the phenomena of shearing dilatation and unloading shrink of saturated sand were considered.On above basic a new calculating constitutive relation model was proposed.There are a few parameters in the model.The physical means of the parameters are very evident and quantized.They could be obtained from the dynamic triaxial test in door.The model was contrasted and validated with the results of the dynamic triaxial test in door.The comparison of the results of the dynamic triaxial test in door and the calculating results of the model indicates that all sorts of phenomenon appearing in the process of liquefaction of saturated sand could be more perfectly reflected by the model.Especially at the initial stage of development of pore water pressure and strain of saturated sand,the results of the dynamic triaxial test in door are consistent with the calculated results of the model very much.But there is some difference between the results at the anaphase of development of pore water pressure and strain.On the path of stress,the calculating and experimenting ultimate state surfaces are almost identical.展开更多
To study the behaviour of reinforced concrete (RC) structures with sections of concrete removed and the reinforcement exposed, 3D nonlinear numerical analysis was performed upon both intact and debonded RC beams by ...To study the behaviour of reinforced concrete (RC) structures with sections of concrete removed and the reinforcement exposed, 3D nonlinear numerical analysis was performed upon both intact and debonded RC beams by using finite element techniques. The deformational characteristics and the ultimate loads were obtained through numerical models, as well as crack and stress distributions. The failure modes can also be deduced from computational results. Compared with intact beams, the normal assumptions of plane section behaviour is not hold true and the patterns of stress and strain are different in debonded RC beams. The numerical results show good consistency with experimental data. This kind of numerical simulation is a supplement to existing codes.展开更多
Accuracy in predictions leads to better planning with a minimum of opportunity lost. In open pit mining,the complexity of operations, coupled with a highly uncertain and dynamic production environment,limit the accura...Accuracy in predictions leads to better planning with a minimum of opportunity lost. In open pit mining,the complexity of operations, coupled with a highly uncertain and dynamic production environment,limit the accuracy of predictions and force a reactive planning approach to mitigate deviations from original plans. A simulation optimization framework/tool is presented in this paper to account for uncertainties in mining operations for robust short-term production planning and proactive decision making. This framework/tool uses a discrete event simulation model of mine operations, which interacts with a goalprogramming based mine operational optimization tool to develop an uncertainty based short-term schedule. Using scenario analysis, this framework allows the planner to make proactive decisions to achieve the mine's operational and long-term objectives. This paper details the development of simulation and optimization models and presents the implementation of the framework on an iron ore mine case study for verification through scenario analysis.展开更多
Boulder/rock mass movements generate ground vibrations that can be recorded by geophone networks.Generally,there are two methods applied to rockfall trajectory reconstruction or rockfall seismic localization.One metho...Boulder/rock mass movements generate ground vibrations that can be recorded by geophone networks.Generally,there are two methods applied to rockfall trajectory reconstruction or rockfall seismic localization.One method uses seismic wave arrival times and is achieved by minimizing the differences in signal arrival times between multiple stations by grid map searching.The other method uses seismic polarization and is achieved by calculating eventsource back azimuths from the seismic polarizations of rockfall signals.In this study,we proposed the use of an overdetermined matrix for joint localization based on the polarization method.The overdetermined matrix considers the contributions of all geophones in the network,and at each geophone is assigned a different weight according to the recorded signal qualities and the reliability of the calibrated back azimuths.This method shows a great advantage relative to the case in which only two sensors are employed.Besides,we suggested three marker parameters for proper frequency band selection in back azimuth calculations:energy,rectilinearity,and a special permanent frequency band(SPF).We found that the back azimuths calculated with energy and an SPF are generally close to the real back azimuths measured in the field,while the SPF is limited by seismic attenuation due to a long-distance propagation.The localization results of rockfalls were validated by using field camera videos and in situ calibrations.Three typical cases and 43 artificially released rockfalls are presented in this paper.The proposed method provides an interesting way to locate rockfall events and track rockfall trajectories and avoids the difficulties of obtaining accurate arrival times,as required by the arrival times method.展开更多
Transition metal-based bimetallic oxides can effectively activate peroxymonosulfate(PMS) for the degradation of organic contaminants, which may be attributed to the enhanced electron transfer efficiency between transi...Transition metal-based bimetallic oxides can effectively activate peroxymonosulfate(PMS) for the degradation of organic contaminants, which may be attributed to the enhanced electron transfer efficiency between transition metals. Here, we investigated the high-efficiency catalytic activation reaction of PMS on a well-defined bimetallic Fe-Mn nanocomposite(BFMN) catalyst. The surface topography and chemical information of BFMN were simultaneously mapped with nanoscale resolution. Rhodamine B(Rh B, as a model pollutant) was used to evaluate the oxidation activity of PMS activation system. The maximum absorption peak of Rh B obviously blue shifted from 554 nm to 501 nm, and decreased sharply to disappear completely within 60 min. The removal performance is better than most of the reported single transition metal oxide. X-ray photoelectron spectroscopy(XPS) imaging of the BFMN electronic structure after catalytic activation confirmed that the accelerated internal electron transfer is mainly caused by the synergy effect of Mn and Fe sites at the catalysis boundary. The outstanding ability of BFMN for PMS chemical adsorption and activation may attribute to the enhanced covalency and reactivity of Mn-O. These results of this study can advance understandings on the origins of bimetallic oxides activity for PMS activation and developing the efficient metal oxide catalysts in real practice.展开更多
This work correlated the detailed work zone location and time data from the Wis LCS system with the five-min inductive loop detector data. One-sample percentile value test and two-sample Kolmogorov-Smirnov(K-S) test w...This work correlated the detailed work zone location and time data from the Wis LCS system with the five-min inductive loop detector data. One-sample percentile value test and two-sample Kolmogorov-Smirnov(K-S) test were applied to compare the speed and flow characteristics between work zone and non-work zone conditions. Furthermore, we analyzed the mobility characteristics of freeway work zones within the urban area of Milwaukee, WI, USA. More than 50% of investigated work zones have experienced speed reduction and 15%-30% is necessary reduced volumes. Speed reduction was more significant within and at the downstream of work zones than at the upstream.展开更多
Earthquakes can cause widely distributed slope failures and damage in mountainous areas.The accurate prediction of ground motions in mountainous areas is essential for managing the seismic risk of urban cities near mo...Earthquakes can cause widely distributed slope failures and damage in mountainous areas.The accurate prediction of ground motions in mountainous areas is essential for managing the seismic risk of urban cities near mountains but is restricted primarily by complex seismic site amplification effects in areas of uneven terrain.This study selected Qiaozhuang town located in the Qingchuan–Pingwu fault zone,Southwest China,as a case study.A simulator for mapped seismic responses using a hybrid model(Si Se RHMap)was applied to compute the multispectral seismic topographic amplification maps at the three slope units surrounding Qiaozhuang town(Weigan hill,Mt.Dong,and Mt.Shizi).Post-earthquake damage survey maps,1 D seismic site response spectral ratios,and H/V spectral ratios of earthquake data were used to validate the computed seismic site amplification factors and resonance frequencies.The results suggest that strong topographic amplification effects usually occur at distinct slope locations,such as hilltops,convex slope positions,upslope,and narrow ridges.The computed topographic amplification factors in the study area reached up to 2.4 at upslope or hilltops,and the resonance frequencies were between 3 and 10 Hz.Topographic effects can be as important as stratigraphic effects when assessing seismic amplification effects in the study area.We conclude that both topographic and stratigraphic effects should be considered in the comprehensive seismic hazard assessment of the study area or other similar mountain towns.展开更多
Understanding the spatial and temporal dynamics of microbial communities in drinking water systems is vital to securing the microbial safety of drinking water.The objective of this study was to comprehensively charact...Understanding the spatial and temporal dynamics of microbial communities in drinking water systems is vital to securing the microbial safety of drinking water.The objective of this study was to comprehensively characterize the dynamics of microbial biomass and bacterial communities at each step of a full-scale drinking water treatment plant in Beijing,China.Both bulk water and biofilm samples on granular activated carbon（GAC） were collected over 9 months.The proportion of cultivable cells decreased during the treatment processes,and this proportion was higher in warm season than cool season,suggesting that treatment processes and water temperature probably had considerable impact on the R2 A cultivability of total bacteria.16 s rRNA gene based 454 pyrosequencing analysis of the bacterial community revealed that Proteobacteria predominated in all samples.The GAC biofilm harbored a distinct population with a much higher relative abundance of Acidobactena than water samples.Principle coordinate analysis and one-way analysis of similarity indicated that the dynamics of the microbial communities in bulk water and biofilm samples were better explained by the treatment processes rather than by sampling time,and distinctive changes of the microbial communities in water occurred after GAC filtration.Furthermore,20 distinct OTUs contributing most to the dissimilarity among samples of different sampling locations and 6 persistent OTUs present in the entire treatment process flow were identified.Overall,our findings demonstrate the significant effects that treatment processes have on the microbial biomass and community fluctuation and provide implications for further targeted investigation on particular bacteria populations.展开更多
Antibiotic resistant bacteria(ARB)with antibiotic resistance genes(ARGs)can reduce or eliminate the effectiveness of antibiotics and thus threaten human health.The United Nations Environment Programme considers antibi...Antibiotic resistant bacteria(ARB)with antibiotic resistance genes(ARGs)can reduce or eliminate the effectiveness of antibiotics and thus threaten human health.The United Nations Environment Programme considers antibiotic resistance the first of six emerging issues of concern.Advanced oxidation processes(AOPs)that combine ultraviolet(UV)irradiation and chemical oxidation(primarily chlorine,hydrogen peroxide,and persulfate)have attracted increasing interest as advanced water and wastewater treatment technologies.These integrated technologies have been reported to significantly elevate the efficiencies of ARB inactivation and ARG degradation compared with direct UV irradiation or chemical oxidation alone due to the generation of multiple reactive species.In this study,the performance and underlying mechanisms of UV/chlorine,UV/hydrogen peroxide,and UV/persulfate processes for controlling ARB and ARGs were reviewed based on recent studies.Factors affecting the process-specific efficiency in controlling ARB and ARGs were discussed,including biotic factors,oxidant dose,UV fluence,pH,and water matrix properties.In addition,the cost-effectiveness of the UV-based AOPs was evaluated using the concept of electrical energy per order.The UV/chlorine process exhibited a higher efficiency with lower energy consumption than other UV-based AOPs in the wastewater matrix,indicating its potential for ARB inactivation and ARG degradation in wastewater treatment.Further studies are required to address the trade-off between toxic byproduct formation and the energy efficiency of the UV/chlorine process in real wastewater to facilitate its optimization and application in the control of ARB and ARGs.展开更多
With the increasing development of Brazil in recent years, major engineering construction works have been designed and built, partieutarly those involving large volumes of mass concrete, such as in the case of dams. M...With the increasing development of Brazil in recent years, major engineering construction works have been designed and built, partieutarly those involving large volumes of mass concrete, such as in the case of dams. Mass concrete, due to its large size and volume, presents a considerable temperature rise caused by cement grain hydration. This temperature rise can be sufficient to cause concrete crack and/or cracking, which may lead to serious problems. In this paper, we sought to study heat generation and temperature field in mass concrete through ANSYS software, which uses finite element method to analyze the problem. This program allows temperatures to be checked for different concrete ages. With that, it is possible to evaluate the temperatures obtained and the factors influencing the results in a short period of time at a low cost. With the help of the software, it is possible to check the temperatures for different concrete properties by analyzing them on different concreting days. Therefore, it was possible to establish that the properties of the concrete directly influence the temperature evolution phenomenon.展开更多
Driving safety is of significance in the automobile industry and transportation systems. Pavement skid resistance has long been recognized as the most important parameter in reducing traffic accidents especially in we...Driving safety is of significance in the automobile industry and transportation systems. Pavement skid resistance has long been recognized as the most important parameter in reducing traffic accidents especially in wet conditions. The knowledge of the friction coefficient and skid resistance is very valuable information for safety enhancement of roads. Thus, it is important to find proper methods for measuring skid resistance and frictional properties of the pavement surface. There is a wide range of measurement methods and devices for measuring skid resistance. This paper presents a review on the research studies that have been done on characterization of the frictional properties of the pavement surface and discussed methods used for measurement and evaluation of texture characteristics and the strengths and weaknesses of these methods. Finally, some ideas have been suggested to develop new methods for better and proper measurement of skid resistance.展开更多
In order to study an isolation system of rolling friction with springs, computer programs were compiled to evaluate the seismic performance based on its movement characteristics. Through the programs, the influences o...In order to study an isolation system of rolling friction with springs, computer programs were compiled to evaluate the seismic performance based on its movement characteristics. Through the programs, the influences of various seismic performance factors, e.g., rolling friction coefficient, spring constant, were systematically investigated. Results show that by increasing the rolling friction coefficient, the structural relative displacement due to seismic load effectively decreases, while the structural response magnitude varies mainly depending on the correlations between the following factors: the spring constant, the earthquake intensity, and the rolling friction coefficient. Furthermore, increasing the spring constant can decrease the structural relative displacement, as well as residual displacement, however, it increases the structural response magnitude. Finally, based on the analyses of various seismic performance factors subjected to the scenario earthquakes, optimized theoretical seismic performance can be achieved by reasonably combining the spring constant and the rolling friction coefficient.展开更多
A unique and well-designed 2D graphitic carbon nitride(g-CN)with sponge-like architecture has been successfully synthesized by engineering supramolecular self-assembly and well-organized SiO 2 nanoparti-cles.The resul...A unique and well-designed 2D graphitic carbon nitride(g-CN)with sponge-like architecture has been successfully synthesized by engineering supramolecular self-assembly and well-organized SiO 2 nanoparti-cles.The resulting material showed great optical and textural characteristics with plenty of open and uni-form pores,which are very helpful whether for multiple light scattering or mass transfer.The formation of boosted delocalizedπ-conjugated electrons at the molecular level and condensed heptazine building blocks result in enhanced carrier density and charge transfer dynamics.Optical emission spectroscopy and time-resolved fluorescence lifetime(TRPL)strongly confirmed the enhancement of light harvesting and prolonged charge carrier lifetime.The optimized sample exhibited a degradation performance of 95%of bisphenol A(BPA,10 mg L-1)after 60 min under visible-light irradiation at pH=5.All the scavenging experiments,probing experiments as well as electron paramagnetic resonance(EPR)confirm that•O 2-is the dominant reactive species that fragments bisphenol A.Interestingly,density functional theory(DFT)calculations unveil that the BPA interaction with a modified g-CN containing porous structure is energeti-cally more favorable than non-porous pure g-CN.Moreover,the toxicity assessment showed that the final degradation products were placed in the non-harmful category based on acute and chronic toxicity.This study presents a promising strategy to modify the g-CN properties and provides an efficient technique for boosting its visible-light photocatalytic activity.展开更多
Yuma County is the top crop producing County in Colorado that is dependent on groundwater supplies from the High Plains aquifer for irrigation. The Arikaree River, a tributary of the Republican River in eastern Colora...Yuma County is the top crop producing County in Colorado that is dependent on groundwater supplies from the High Plains aquifer for irrigation. The Arikaree River, a tributary of the Republican River in eastern Colorado, is supplied with water from the High Plains aquifer. The Arikaree River alluvium is also a habitat for many terrestrial invertebrates and the threatened Hybognathus hankinsoni (Brassy Minnow). The constant demand on the High Plains aquifer has created declining water levels at the linear rate of 0.183 m/year with the deepest pool in the Arikaree River drying up in 8 to 12 years. In addition to the demands for habitats, the surrounding irrigated agricultural lands require water for crop production. These challenges are currently confronting farmers in eastern Colorado and this research presents possible alternatives to meet these demands. This research presents a combination water balance model, water conservation model, and water conservation survey results from farmers in eastern Colorado to identify alternatives to extend the life of the Arikaree River. The first alternative was to examine the reduction in irrigation water from removing the 18 alluvial irrigation wells that could extend the Arikaree River pools from drying up for 30 years. The other scenario found that water conservation practices with participation of 43%, 57%, and 62% of farmers would extend the drying time to 20, 30, and 40 years, respectively. The final alternative studied was the required participation in conservation practices to stop the decline of the High Plains Aquifer. The analysis found that 77% participation of farmers in all conservation alternatives or reducing pumping by 62.9% would be necessary to stabilize the High Plains Aquifer.展开更多
It is too difficult for a compacted specimen of unsaturated clay prepared and used in a laboratory test to have homogeneous water content and porosity. Although there have been many hydraulic and mechanical studies, t...It is too difficult for a compacted specimen of unsaturated clay prepared and used in a laboratory test to have homogeneous water content and porosity. Although there have been many hydraulic and mechanical studies, there are few papers related to homogeneity of specimen. However, it is clear that homogeneity of specimen influences mechanical properties. In this paper, the use of micro-waves is proposed as method for making homogeneous specimens. The study results indicate that specimens made by micro-waves are more homogeneous than compacted specimens.展开更多
In this paper, we show one of the possibility utilizing typical origami structures for civil engineering fields such as the bridge bearing support. We numerically investigate axial spring constants and buckling behavi...In this paper, we show one of the possibility utilizing typical origami structures for civil engineering fields such as the bridge bearing support. We numerically investigate axial spring constants and buckling behaviors of bellows-like origami tube structures. The bellows-like origami tube structures, which can be folded because of elastic deformations, work as a kind of spring. If the initial heights of the bellows-like origami tubes are less than 90% of the height of the prismatic tubes without bellows-like folded lines, the spring constants of the bellows-like tubes are very low compared with those of the prismatic tubes. The buckling loads and patterns of the bellows-like tubes vary depending on the initial heights of the tubes.展开更多
Cohesion is an important soil strength parameter for the overall structure and quality of building foundations as well as slope stability. For a civil engineering project, cohesion (c) can be determined directly from ...Cohesion is an important soil strength parameter for the overall structure and quality of building foundations as well as slope stability. For a civil engineering project, cohesion (c) can be determined directly from mainly unconfined compression tests, direct shear tests, and triaxial tests of soil. However, it’s quite challenging to collect soil samples as there are time and cost constraints, as well as a diversity of soil deposits. Hence, this research aims to demonstrate a simplified method in order to determine the strength parameter of cohesive soil. Here, we propose an alternative solution adopting statistical correlations and machine learning techniques to establish correlations between the liquid limit, plastic limit, moisture content and %fine of soil with the strength parameter. In laboratory testing, these parameters can be obtained easily and these tests are relatively simple, quick to perform and also comparatively inexpensive. Hence, several test results were used from 100 boreholes which were soft soil or silty clay-type soil. Using the collected in-situ and lab test results of soil samples, a Multiple Linear Regression (MLR), Random Forest Regression (RFR) and Machine Learning (ML) model will be developed to establish a relationship between cohesion and the available test results. In order to assess the performances of both models, several performance indicators like: correlation coefficient (R<sup>2</sup>), mean squared error (MSE), root mean square error (RMSE), and mean average error (MAE) will be used. These correlation coefficients will be used to demonstrate the prediction capacity and accuracy of both models. It should be noted that this approach will substitute the conventional testing required for strength parameters, which is both expensive and time-consuming.展开更多
This research aims to develop the appropriate biorefinery process integrating anaerobic digestion(AD)and hydrothermal carbonization(HTC)to recover the highest energy from the pretreated elephant dung.Initially,the raw...This research aims to develop the appropriate biorefinery process integrating anaerobic digestion(AD)and hydrothermal carbonization(HTC)to recover the highest energy from the pretreated elephant dung.Initially,the raw elephant dung was physically processed by washing with water to generate the liquid waste,i.e.,washing water(WW),and solid waste,i.e.,washed fiber(WF).The appropriate substrate-to-inoculum ratio(SIR)and the inoculum source of the AD of WW were determined and the HTC temperature of WF was also examined.The results indicated that the AD of WW with the SIR of 1:2 and anaerobically digested swine manure as the inoculum presented the highest methane and energy yields of 412.3±9.9 N mL/g VS added and 2,220.1±53.03 MJ/ton dry wt.,respectively.For HTC of WF,the optimum condition was the hydrothermal temperature of 170℃ at the residence time of 60 min.The highest hydrochar and energy yields were 76.8%±1.9%dry wt.and 12,067.0±452.1 MJ/ton dry wt.,respectively.Thus,this biorefinery process could simultaneously treat elephant campderived waste and produce clean energy.展开更多
基金the support from the company Shell Brasil Petroleo and FAPESP through the “Reserch Centre for Gas Innovation-RCGI”(Fapesp Proc.2014/50279-4),hosted by the University of Sao Paulo,and the strategic importance of the support given by ANP(Brazil’s National Oil,Natural Gas and Biofuels Agency)through the R&D levy regulation.
文摘This paper presents a proposal for an experimental salt cavern in offshore ultra-deep water for CO2 abatement,including the instrumentation plan and well conceptual design evaluated for carbon capture and storage(CCS)application.These studies are based on applied computational mechanics associated with field experimentation that has contributed to the technical feasibility of the underground potash mine at the State of Sergipe in Brazil.This knowhow allowed the stability analysis of several salt caverns for brine production at the State of Alagoas in Brazil and to the drilling through stratified thick layers of salt of the pre-salt reservoirs in Santos Basin.Now,this knowledge has been applied in the design of onshore and offshore salt caverns opened by dissolution for storage of natural gas and CO2.The geomechanical study,through the application of computational mechanics,of offshore giant salt caverns of 450 m high by 150 m in diameter,shows that one cavern can store about 4 billion Sm3 or 7.2 million tons of CO2.Before the construction of the giant cavern,which will be the first gas storage offshore in the world,it has been decided to develop an experimental one,with smaller size,to obtained field parameters.The experimental cavern will allow the calibration of parameters to be used in the structural integrity analysis of the cavern and well for storage of natural gas which is rich in CO2 under high pressure.
基金funded by the Fundamental Research Funds for the Central Universities(No.B210202031)the National Natural Science Foundation of China(No.41606042)the Marine Renewable Energy Foundation,State Oceanic Administration,China(No.GHME2017YY01).
文摘In this study,a coupled tide-surge-wave model was developed and applied to the South Yellow Sea.The coupled model simulated the evolution of storm surges and waves caused by extreme weather events,such as tropical cyclones,cold waves,extratropical cyclones coupled with a cold wave,and tropical cyclones coupled with a cold wave.The modeled surge level and significant wave height matched the measured data well.Simulation results of the typhoon with different intensities revealed that the radius to the maximum wind speed of a typhoon with 1.5 times wind speed decreased,and its influence range was farther away from the Jiangsu coastal region;moreover,the impact on surge levels was weakened.Thereafter,eight hypothetical typhoons based on Typhoon Chan-hom were designed to investigate the effects of varying typhoon tracks on the extreme value and spatial distribution of storm surges in the offshore area of Jiangsu Province.The typhoon along path 2 mainly affected the Rudong coast,and the topography of the Rudong coast was conducive to the increase in surge level.Therefore,the typhoon along path 2 induced the largest surge level,which reached up to 2.91 m in the radial sand ridge area.The maximum surge levels in the Haizhou Bay area and the middle straight coastline area reached up to 2.37 and 2.08 m,respectively.In terms of typhoons active in offshore areas,the radial sand ridge area was most likely to be threatened by typhoon-induced storm surges.
基金Project(59979001) supported by the National Natural Science Foundation of China
文摘According to the existing problems of liquefaction models of saturated sand that were put forward under dynamic action,on the basis of Handin-Drnevich model,a new calculating model of the dynamic constitutive relation of saturated sand was put forward.The model was based on the basic hypothesis of instantaneous limit balance according to the basic principle that the stress estate is the destroyed condition was not overstepped.The calculated method of increment nonlinear was referenced and combined with the excellence of the model of distributed particles.The process of vibrating liquefaction of saturated sand was divided into some areas.And the phenomena of shearing dilatation and unloading shrink of saturated sand were considered.On above basic a new calculating constitutive relation model was proposed.There are a few parameters in the model.The physical means of the parameters are very evident and quantized.They could be obtained from the dynamic triaxial test in door.The model was contrasted and validated with the results of the dynamic triaxial test in door.The comparison of the results of the dynamic triaxial test in door and the calculating results of the model indicates that all sorts of phenomenon appearing in the process of liquefaction of saturated sand could be more perfectly reflected by the model.Especially at the initial stage of development of pore water pressure and strain of saturated sand,the results of the dynamic triaxial test in door are consistent with the calculated results of the model very much.But there is some difference between the results at the anaphase of development of pore water pressure and strain.On the path of stress,the calculating and experimenting ultimate state surfaces are almost identical.
文摘To study the behaviour of reinforced concrete (RC) structures with sections of concrete removed and the reinforcement exposed, 3D nonlinear numerical analysis was performed upon both intact and debonded RC beams by using finite element techniques. The deformational characteristics and the ultimate loads were obtained through numerical models, as well as crack and stress distributions. The failure modes can also be deduced from computational results. Compared with intact beams, the normal assumptions of plane section behaviour is not hold true and the patterns of stress and strain are different in debonded RC beams. The numerical results show good consistency with experimental data. This kind of numerical simulation is a supplement to existing codes.
基金part of a PhD research, which was supported by Mine Optimization Laboratory, University of Alberta-Canada
文摘Accuracy in predictions leads to better planning with a minimum of opportunity lost. In open pit mining,the complexity of operations, coupled with a highly uncertain and dynamic production environment,limit the accuracy of predictions and force a reactive planning approach to mitigate deviations from original plans. A simulation optimization framework/tool is presented in this paper to account for uncertainties in mining operations for robust short-term production planning and proactive decision making. This framework/tool uses a discrete event simulation model of mine operations, which interacts with a goalprogramming based mine operational optimization tool to develop an uncertainty based short-term schedule. Using scenario analysis, this framework allows the planner to make proactive decisions to achieve the mine's operational and long-term objectives. This paper details the development of simulation and optimization models and presents the implementation of the framework on an iron ore mine case study for verification through scenario analysis.
基金funded by the Department of Earth Sciences-University of Firenze(Italy)as part of the PRIN 2009 project–Advanced monitoring techniques for the development of early warning procedures on large rockslides(prot.20084FAHR7_001)。
文摘Boulder/rock mass movements generate ground vibrations that can be recorded by geophone networks.Generally,there are two methods applied to rockfall trajectory reconstruction or rockfall seismic localization.One method uses seismic wave arrival times and is achieved by minimizing the differences in signal arrival times between multiple stations by grid map searching.The other method uses seismic polarization and is achieved by calculating eventsource back azimuths from the seismic polarizations of rockfall signals.In this study,we proposed the use of an overdetermined matrix for joint localization based on the polarization method.The overdetermined matrix considers the contributions of all geophones in the network,and at each geophone is assigned a different weight according to the recorded signal qualities and the reliability of the calibrated back azimuths.This method shows a great advantage relative to the case in which only two sensors are employed.Besides,we suggested three marker parameters for proper frequency band selection in back azimuth calculations:energy,rectilinearity,and a special permanent frequency band(SPF).We found that the back azimuths calculated with energy and an SPF are generally close to the real back azimuths measured in the field,while the SPF is limited by seismic attenuation due to a long-distance propagation.The localization results of rockfalls were validated by using field camera videos and in situ calibrations.Three typical cases and 43 artificially released rockfalls are presented in this paper.The proposed method provides an interesting way to locate rockfall events and track rockfall trajectories and avoids the difficulties of obtaining accurate arrival times,as required by the arrival times method.
基金supported by the National Key Research and Development Program of China (No. 2020YFC1808300)National Natural Science Foundation of China (Nos. 42077185, 41772264)the Research Fund of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection (No. SKLGP2020Z002)。
文摘Transition metal-based bimetallic oxides can effectively activate peroxymonosulfate(PMS) for the degradation of organic contaminants, which may be attributed to the enhanced electron transfer efficiency between transition metals. Here, we investigated the high-efficiency catalytic activation reaction of PMS on a well-defined bimetallic Fe-Mn nanocomposite(BFMN) catalyst. The surface topography and chemical information of BFMN were simultaneously mapped with nanoscale resolution. Rhodamine B(Rh B, as a model pollutant) was used to evaluate the oxidation activity of PMS activation system. The maximum absorption peak of Rh B obviously blue shifted from 554 nm to 501 nm, and decreased sharply to disappear completely within 60 min. The removal performance is better than most of the reported single transition metal oxide. X-ray photoelectron spectroscopy(XPS) imaging of the BFMN electronic structure after catalytic activation confirmed that the accelerated internal electron transfer is mainly caused by the synergy effect of Mn and Fe sites at the catalysis boundary. The outstanding ability of BFMN for PMS chemical adsorption and activation may attribute to the enhanced covalency and reactivity of Mn-O. These results of this study can advance understandings on the origins of bimetallic oxides activity for PMS activation and developing the efficient metal oxide catalysts in real practice.
基金Project(61620106002)supported by the National Natural Science Foundation of ChinaProject(2016YFB0100906)supported by the National Key R&D Program in China+1 种基金Project(2015364X16030)supported by the Information Technology Research Project of Ministry of Transport of ChinaProject(2242015K42132)supported by the Fundamental Sciences of Southeast University,China
文摘This work correlated the detailed work zone location and time data from the Wis LCS system with the five-min inductive loop detector data. One-sample percentile value test and two-sample Kolmogorov-Smirnov(K-S) test were applied to compare the speed and flow characteristics between work zone and non-work zone conditions. Furthermore, we analyzed the mobility characteristics of freeway work zones within the urban area of Milwaukee, WI, USA. More than 50% of investigated work zones have experienced speed reduction and 15%-30% is necessary reduced volumes. Speed reduction was more significant within and at the downstream of work zones than at the upstream.
基金financially supported by the Funds for Creative Research Groups of China(Grant No.41521002)the National Natural Science Foundation of China(Grant No.42077257)the Open Fund of the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Grants No.SKLGP2019K024 and No.SKLGP2019K006 assigned for G.Grelle’s competition proposal)。
文摘Earthquakes can cause widely distributed slope failures and damage in mountainous areas.The accurate prediction of ground motions in mountainous areas is essential for managing the seismic risk of urban cities near mountains but is restricted primarily by complex seismic site amplification effects in areas of uneven terrain.This study selected Qiaozhuang town located in the Qingchuan–Pingwu fault zone,Southwest China,as a case study.A simulator for mapped seismic responses using a hybrid model(Si Se RHMap)was applied to compute the multispectral seismic topographic amplification maps at the three slope units surrounding Qiaozhuang town(Weigan hill,Mt.Dong,and Mt.Shizi).Post-earthquake damage survey maps,1 D seismic site response spectral ratios,and H/V spectral ratios of earthquake data were used to validate the computed seismic site amplification factors and resonance frequencies.The results suggest that strong topographic amplification effects usually occur at distinct slope locations,such as hilltops,convex slope positions,upslope,and narrow ridges.The computed topographic amplification factors in the study area reached up to 2.4 at upslope or hilltops,and the resonance frequencies were between 3 and 10 Hz.Topographic effects can be as important as stratigraphic effects when assessing seismic amplification effects in the study area.We conclude that both topographic and stratigraphic effects should be considered in the comprehensive seismic hazard assessment of the study area or other similar mountain towns.
基金supported by the China Major Science and Technology Program for Water Pollution Control and Treatment(No.2012ZX07404-002)the Special Fund of State Key Joint Laboratory of Environment Simulation and Pollution Control(No.14K09ESPCT)
文摘Understanding the spatial and temporal dynamics of microbial communities in drinking water systems is vital to securing the microbial safety of drinking water.The objective of this study was to comprehensively characterize the dynamics of microbial biomass and bacterial communities at each step of a full-scale drinking water treatment plant in Beijing,China.Both bulk water and biofilm samples on granular activated carbon（GAC） were collected over 9 months.The proportion of cultivable cells decreased during the treatment processes,and this proportion was higher in warm season than cool season,suggesting that treatment processes and water temperature probably had considerable impact on the R2 A cultivability of total bacteria.16 s rRNA gene based 454 pyrosequencing analysis of the bacterial community revealed that Proteobacteria predominated in all samples.The GAC biofilm harbored a distinct population with a much higher relative abundance of Acidobactena than water samples.Principle coordinate analysis and one-way analysis of similarity indicated that the dynamics of the microbial communities in bulk water and biofilm samples were better explained by the treatment processes rather than by sampling time,and distinctive changes of the microbial communities in water occurred after GAC filtration.Furthermore,20 distinct OTUs contributing most to the dissimilarity among samples of different sampling locations and 6 persistent OTUs present in the entire treatment process flow were identified.Overall,our findings demonstrate the significant effects that treatment processes have on the microbial biomass and community fluctuation and provide implications for further targeted investigation on particular bacteria populations.
基金supported by grants from the Research Grants Council of the Hong Kong SAR,China(T21-705/20-N and 16210221).
文摘Antibiotic resistant bacteria(ARB)with antibiotic resistance genes(ARGs)can reduce or eliminate the effectiveness of antibiotics and thus threaten human health.The United Nations Environment Programme considers antibiotic resistance the first of six emerging issues of concern.Advanced oxidation processes(AOPs)that combine ultraviolet(UV)irradiation and chemical oxidation(primarily chlorine,hydrogen peroxide,and persulfate)have attracted increasing interest as advanced water and wastewater treatment technologies.These integrated technologies have been reported to significantly elevate the efficiencies of ARB inactivation and ARG degradation compared with direct UV irradiation or chemical oxidation alone due to the generation of multiple reactive species.In this study,the performance and underlying mechanisms of UV/chlorine,UV/hydrogen peroxide,and UV/persulfate processes for controlling ARB and ARGs were reviewed based on recent studies.Factors affecting the process-specific efficiency in controlling ARB and ARGs were discussed,including biotic factors,oxidant dose,UV fluence,pH,and water matrix properties.In addition,the cost-effectiveness of the UV-based AOPs was evaluated using the concept of electrical energy per order.The UV/chlorine process exhibited a higher efficiency with lower energy consumption than other UV-based AOPs in the wastewater matrix,indicating its potential for ARB inactivation and ARG degradation in wastewater treatment.Further studies are required to address the trade-off between toxic byproduct formation and the energy efficiency of the UV/chlorine process in real wastewater to facilitate its optimization and application in the control of ARB and ARGs.
文摘With the increasing development of Brazil in recent years, major engineering construction works have been designed and built, partieutarly those involving large volumes of mass concrete, such as in the case of dams. Mass concrete, due to its large size and volume, presents a considerable temperature rise caused by cement grain hydration. This temperature rise can be sufficient to cause concrete crack and/or cracking, which may lead to serious problems. In this paper, we sought to study heat generation and temperature field in mass concrete through ANSYS software, which uses finite element method to analyze the problem. This program allows temperatures to be checked for different concrete ages. With that, it is possible to evaluate the temperatures obtained and the factors influencing the results in a short period of time at a low cost. With the help of the software, it is possible to check the temperatures for different concrete properties by analyzing them on different concreting days. Therefore, it was possible to establish that the properties of the concrete directly influence the temperature evolution phenomenon.
文摘Driving safety is of significance in the automobile industry and transportation systems. Pavement skid resistance has long been recognized as the most important parameter in reducing traffic accidents especially in wet conditions. The knowledge of the friction coefficient and skid resistance is very valuable information for safety enhancement of roads. Thus, it is important to find proper methods for measuring skid resistance and frictional properties of the pavement surface. There is a wide range of measurement methods and devices for measuring skid resistance. This paper presents a review on the research studies that have been done on characterization of the frictional properties of the pavement surface and discussed methods used for measurement and evaluation of texture characteristics and the strengths and weaknesses of these methods. Finally, some ideas have been suggested to develop new methods for better and proper measurement of skid resistance.
基金Project(51308549)supported by the National Natural Science Foundation,China
文摘In order to study an isolation system of rolling friction with springs, computer programs were compiled to evaluate the seismic performance based on its movement characteristics. Through the programs, the influences of various seismic performance factors, e.g., rolling friction coefficient, spring constant, were systematically investigated. Results show that by increasing the rolling friction coefficient, the structural relative displacement due to seismic load effectively decreases, while the structural response magnitude varies mainly depending on the correlations between the following factors: the spring constant, the earthquake intensity, and the rolling friction coefficient. Furthermore, increasing the spring constant can decrease the structural relative displacement, as well as residual displacement, however, it increases the structural response magnitude. Finally, based on the analyses of various seismic performance factors subjected to the scenario earthquakes, optimized theoretical seismic performance can be achieved by reasonably combining the spring constant and the rolling friction coefficient.
基金the National Research Foundation of Korea(NRF)grant funded by the Korea government(MIST)(No.2019R1A2C2085250)the Brain Pool(BP)fellowship grant funded by the Korea government(No.2019H1D3A1A01070060).
文摘A unique and well-designed 2D graphitic carbon nitride(g-CN)with sponge-like architecture has been successfully synthesized by engineering supramolecular self-assembly and well-organized SiO 2 nanoparti-cles.The resulting material showed great optical and textural characteristics with plenty of open and uni-form pores,which are very helpful whether for multiple light scattering or mass transfer.The formation of boosted delocalizedπ-conjugated electrons at the molecular level and condensed heptazine building blocks result in enhanced carrier density and charge transfer dynamics.Optical emission spectroscopy and time-resolved fluorescence lifetime(TRPL)strongly confirmed the enhancement of light harvesting and prolonged charge carrier lifetime.The optimized sample exhibited a degradation performance of 95%of bisphenol A(BPA,10 mg L-1)after 60 min under visible-light irradiation at pH=5.All the scavenging experiments,probing experiments as well as electron paramagnetic resonance(EPR)confirm that•O 2-is the dominant reactive species that fragments bisphenol A.Interestingly,density functional theory(DFT)calculations unveil that the BPA interaction with a modified g-CN containing porous structure is energeti-cally more favorable than non-porous pure g-CN.Moreover,the toxicity assessment showed that the final degradation products were placed in the non-harmful category based on acute and chronic toxicity.This study presents a promising strategy to modify the g-CN properties and provides an efficient technique for boosting its visible-light photocatalytic activity.
文摘Yuma County is the top crop producing County in Colorado that is dependent on groundwater supplies from the High Plains aquifer for irrigation. The Arikaree River, a tributary of the Republican River in eastern Colorado, is supplied with water from the High Plains aquifer. The Arikaree River alluvium is also a habitat for many terrestrial invertebrates and the threatened Hybognathus hankinsoni (Brassy Minnow). The constant demand on the High Plains aquifer has created declining water levels at the linear rate of 0.183 m/year with the deepest pool in the Arikaree River drying up in 8 to 12 years. In addition to the demands for habitats, the surrounding irrigated agricultural lands require water for crop production. These challenges are currently confronting farmers in eastern Colorado and this research presents possible alternatives to meet these demands. This research presents a combination water balance model, water conservation model, and water conservation survey results from farmers in eastern Colorado to identify alternatives to extend the life of the Arikaree River. The first alternative was to examine the reduction in irrigation water from removing the 18 alluvial irrigation wells that could extend the Arikaree River pools from drying up for 30 years. The other scenario found that water conservation practices with participation of 43%, 57%, and 62% of farmers would extend the drying time to 20, 30, and 40 years, respectively. The final alternative studied was the required participation in conservation practices to stop the decline of the High Plains Aquifer. The analysis found that 77% participation of farmers in all conservation alternatives or reducing pumping by 62.9% would be necessary to stabilize the High Plains Aquifer.
文摘It is too difficult for a compacted specimen of unsaturated clay prepared and used in a laboratory test to have homogeneous water content and porosity. Although there have been many hydraulic and mechanical studies, there are few papers related to homogeneity of specimen. However, it is clear that homogeneity of specimen influences mechanical properties. In this paper, the use of micro-waves is proposed as method for making homogeneous specimens. The study results indicate that specimens made by micro-waves are more homogeneous than compacted specimens.
文摘In this paper, we show one of the possibility utilizing typical origami structures for civil engineering fields such as the bridge bearing support. We numerically investigate axial spring constants and buckling behaviors of bellows-like origami tube structures. The bellows-like origami tube structures, which can be folded because of elastic deformations, work as a kind of spring. If the initial heights of the bellows-like origami tubes are less than 90% of the height of the prismatic tubes without bellows-like folded lines, the spring constants of the bellows-like tubes are very low compared with those of the prismatic tubes. The buckling loads and patterns of the bellows-like tubes vary depending on the initial heights of the tubes.
文摘Cohesion is an important soil strength parameter for the overall structure and quality of building foundations as well as slope stability. For a civil engineering project, cohesion (c) can be determined directly from mainly unconfined compression tests, direct shear tests, and triaxial tests of soil. However, it’s quite challenging to collect soil samples as there are time and cost constraints, as well as a diversity of soil deposits. Hence, this research aims to demonstrate a simplified method in order to determine the strength parameter of cohesive soil. Here, we propose an alternative solution adopting statistical correlations and machine learning techniques to establish correlations between the liquid limit, plastic limit, moisture content and %fine of soil with the strength parameter. In laboratory testing, these parameters can be obtained easily and these tests are relatively simple, quick to perform and also comparatively inexpensive. Hence, several test results were used from 100 boreholes which were soft soil or silty clay-type soil. Using the collected in-situ and lab test results of soil samples, a Multiple Linear Regression (MLR), Random Forest Regression (RFR) and Machine Learning (ML) model will be developed to establish a relationship between cohesion and the available test results. In order to assess the performances of both models, several performance indicators like: correlation coefficient (R<sup>2</sup>), mean squared error (MSE), root mean square error (RMSE), and mean average error (MAE) will be used. These correlation coefficients will be used to demonstrate the prediction capacity and accuracy of both models. It should be noted that this approach will substitute the conventional testing required for strength parameters, which is both expensive and time-consuming.
基金supported by Thailand Science Research and Innovation(TSRI)with a fundamental fund(Basic Research Fund)from Chiang Mai Rajabhat University(Grant No.TSRI.39/66)Office of the Permanent Secretary,Ministry of Higher Education,Science,Research and Innovation(OPS MHESI)(Grant No.RGNS 63-199).
文摘This research aims to develop the appropriate biorefinery process integrating anaerobic digestion(AD)and hydrothermal carbonization(HTC)to recover the highest energy from the pretreated elephant dung.Initially,the raw elephant dung was physically processed by washing with water to generate the liquid waste,i.e.,washing water(WW),and solid waste,i.e.,washed fiber(WF).The appropriate substrate-to-inoculum ratio(SIR)and the inoculum source of the AD of WW were determined and the HTC temperature of WF was also examined.The results indicated that the AD of WW with the SIR of 1:2 and anaerobically digested swine manure as the inoculum presented the highest methane and energy yields of 412.3±9.9 N mL/g VS added and 2,220.1±53.03 MJ/ton dry wt.,respectively.For HTC of WF,the optimum condition was the hydrothermal temperature of 170℃ at the residence time of 60 min.The highest hydrochar and energy yields were 76.8%±1.9%dry wt.and 12,067.0±452.1 MJ/ton dry wt.,respectively.Thus,this biorefinery process could simultaneously treat elephant campderived waste and produce clean energy.
