The concept of“carbon neutrality”poses a huge challenge for chemical engineering and brings great opportunities for boosting the development of novel technologies to realize carbon offsetting and reduce carbon emiss...The concept of“carbon neutrality”poses a huge challenge for chemical engineering and brings great opportunities for boosting the development of novel technologies to realize carbon offsetting and reduce carbon emissions.Developing high-efficient,low-cost,energy-efficient and eco-friendly microfluidicbased microchemical engineering is of great significance.Such kind of“green microfluidics”can reduce carbon emissions from the source of raw materials and facilitate controllable and intensified microchemical engineering processes,which represents the new power for the transformation and upgrading of chemical engineering industry.Here,a brief review of green microfluidics for achieving carbon neutral microchemical engineering is presented,with specific discussions about the characteristics and feasibility of applying green microfluidics in realizing carbon neutrality.Development of green microfluidic systems are categorized and reviewed,including the construction of microfluidic devices by bio-based substrate materials and by low carbon fabrication methods,and the use of more biocompatible and nondestructive fluidic systems such as aqueous two-phase systems(ATPSs).Moreover,low carbon applications benefit from green microfluidics are summarized,ranging from separation and purification of biomolecules,high-throughput screening of chemicals and drugs,rapid and cost-effective detections,to synthesis of fine chemicals and novel materials.Finally,challenges and perspectives for further advancing green microfluidics in microchemical engineering for carbon neutrality are proposed and discussed.展开更多
Electrochemical methods are environmentally friendly and have unique advantages in the synthesis of organic chemicals.However,their implementation is limited due to the complex transport problems posed by traditional ...Electrochemical methods are environmentally friendly and have unique advantages in the synthesis of organic chemicals.However,their implementation is limited due to the complex transport problems posed by traditional electrochemical reactors.Recently,the application of microreaction technology in electrosynthesis studies has reduced the transport distance of ions and increased the specific surface area of electrodes,leading to efficient,successive,and easily scaled-up electrosynthesis technologies.In this review article,engineering advantages of using microchannels in electrosynthesis are discussed from process enhancement perspective.Flow patterns and mass transfer behaviors in recently reported electrochemical microreactors are analyzed,and prototypes for the reactor scale-up are reviewed.As a relatively new research area,many scientific rules and engineering features of electrosynthesis in microreactors require elucidation.Potential research foci,considered crucial for the development of novel electrosynthesis technology,are therefore proposed.展开更多
Chemical industry project management involves complex decision making situations that require discerning abilities and methods to make sound decisions. Chemical engineers as project managers are faced with decision en...Chemical industry project management involves complex decision making situations that require discerning abilities and methods to make sound decisions. Chemical engineers as project managers are faced with decision environments and problems in chemical industry projects that are complex. Multiple-criteria decision making （MCDM） approaches are major parts of decision theory and analysis. This paper presents all of MCDM approaches for use in chemical engineering management decisions. In this work, case study is Research and Development （R＆D） project selection in chemical industry. The ability to make sound decisions is very important to success of R＆D projects. It is hoped that this work will provide a ready reference on MCDM and this will encourage the application of the MCDM in chemical engineering management.展开更多
This study demonstrates the successful fabrication of solid-state bilayers using LiFePO_(4)(LFP)cathodes and Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP)-based Composite Solid Electrolytes(CSEs)via Cold Sintering Proces...This study demonstrates the successful fabrication of solid-state bilayers using LiFePO_(4)(LFP)cathodes and Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP)-based Composite Solid Electrolytes(CSEs)via Cold Sintering Process(CSP).By optimizing the sintering pressure,it is achieved an intimate contact between the cathode and the solid electrolyte,leading to an enhanced electrochemical performance.Bilayers cold sintered at 300 MPa and a low-sintering temperature of 150℃exhibit high ionic conductivities(0.5 mS cm^(-1))and stable specific capacities at room temperature(160.1 mAh g^(-1)LFP at C/10 and 75.8 mAh g^(-1)_(LFP)at 1 C).Moreover,an operando electrochemical impedance spectroscopy(EIS)technique is employed to identify limiting factors of the bilayer kinetics and to anticipate the overall electrochemical behavior.Results suggest that capacity fading can occur in samples prepared with high sintering pressures due to a volume reduction in the LFP crystalline cell.This work demonstrates the potential of CSP to produce straightforward high-performance bilayers and introduces a valuable non-destructive instrument for understanding and avoiding degradation in solid-state lithium-based batteries.展开更多
Three large π-conjugated and imine-based COFs,named TFP-TAB,TFP-TTA,and TTA-TTB,were synthesized via the ordered incorporation of benzene and triazine rings in the same host framework to study how the structural unit...Three large π-conjugated and imine-based COFs,named TFP-TAB,TFP-TTA,and TTA-TTB,were synthesized via the ordered incorporation of benzene and triazine rings in the same host framework to study how the structural units affect the efficiency of CO_(2)photoreduction.Results from both experiments and density-functional theory(DFT)calculations indicate the separation and transfer of the photoinduced charges is highly related to the triazine-N content and the conjugation degree in the skeletons of COFs.High-efficiency CO_(2)photoreduction can be achieved by rationally adjusting the number and position of both benzene and triazine rings in the COFs.Specifically,TTA-TTB,with orderly interlaced triazine-benzene heterojunctions,can suppress the recombination probability of electrons and holes,which effectively immobilizes the key species(COOH)and lowers the free energy change of the potential-determining step,and thus exhibits a superior visible-light-induced photocatalytic activity that yields 121.7 μmol HCOOH g^(-1)h^(-1).This research,therefore,helps to elucidate the effects of the different structural blocks in COFs on inherent heterogeneous photocatalysis for CO_(2)reduction at a molecular level.展开更多
Zero liquid discharge(ZLD)treatment and reuse equipment of high salinity wastewater in coal-chemical industry often occur in various types of blockage problems because of high salt content,affecting the long-term stab...Zero liquid discharge(ZLD)treatment and reuse equipment of high salinity wastewater in coal-chemical industry often occur in various types of blockage problems because of high salt content,affecting the long-term stability of the device.In this study,the effects of solution temperature,steel,reaction time and wall roughness on fouling were investigated.The changes in the contents of fouling and fouling substances were qualitatively and quantitatively analyzed by XRD and EDS respectively,and the formation of scale was observed by SEM.The results show that with temperature increasing,Q235 steel is the most difficult to scale.Scaling rate of all salt scales reaches a maximum after 12 h,and the fouling rate decreases significantly from 12 to 48 h.It gradually stabilizes at 48 to 96 h.With the roughness increasing,the thickness of fouling layer increases,and a linear relationship is presented for 1 to 10 h.By comparing actual and simulated wastewater scaling rates,the relationship between actual and simulated wastewater scaling rates is y=ax-0.494.The composition of the scale was analyzed,calcium carbonate is the main product and increases with fouling time.Based on the above-mentioned results combining literatures,the hybrid prediction model with calcium carbonate as the main product is put forward.It is discussed microscopically that calcium carbonate is converted from aragonite and vaterite in a thermodynamically metastable state to calcite in a thermodynamically stable state.展开更多
Density functional theory is applied to predicting the structures and electrostatic potentials of planar electrochemical surfaces within the framework of the restricted primitive model where small ions are represented...Density functional theory is applied to predicting the structures and electrostatic potentials of planar electrochemical surfaces within the framework of the restricted primitive model where small ions are represented by charged hard spheres of equal diameter and the solvent is assumed to be a continuous dielectric medium. The hard-sphere contribution to the excess Helmholtz energy functional is evaluated using the modified fundamentalmeasure theory and the electrostatic contribution is obtained from the quadratic functional Taylor expansion using the second-order direct correlation function from the mean-spherical approximation. Numerical results for the ionic density profiles and the mean electrostatic potentials near a planar surface of various charge densities are in excellent agreement with molecular simulations. In contrast to the modified Gouy-Chapman theory, the present density functional theory correctly predicts the second layer formation and charge inversion of charged surfaces as observed in simulations and in experiments. The theory has also been tested with the zeta potentials of positively charged polystyrene particles in aqueous solutions of KBr. Good agreement is achieved between the calculated and experimental results.展开更多
Development of a predictive tool for H_2S solubility estimation can be very helpful in gas sweetening industry. Experimental databases on H_2 S solubility were rarely available, so as reliable predictive models. Thus,...Development of a predictive tool for H_2S solubility estimation can be very helpful in gas sweetening industry. Experimental databases on H_2 S solubility were rarely available, so as reliable predictive models. Thus, in this study the H_2 S solubility database was established, and then a Least-Squares Support Vector Machine(LSSVM) approach based on the established database is proposed. Group contribution method was also applied to eliminate the model's dependence on experimental data. Accordingly, our proposed LSSVM model can predict H_2 S solubility as a function of temperature, pressure, and 15 different chemical structures of Ionic liquids(ILs). Root Mean Square Error(RMSE) and coefficient of determination(R^2) are 0.0122 and 0.9941, respectively. Moreover, comparison of our model with other existing models showed its reliability for H_2 S solubility in ILs. This can be very useful for engineers dealing with gas sweetening process in different applications of analysis, simulation, and designation.展开更多
Intelligent fault recognition techniques are essential to ensure the long-term reliability of manufacturing.Due to the variations in material,equipment and environment,the process variables monitored by sensors contai...Intelligent fault recognition techniques are essential to ensure the long-term reliability of manufacturing.Due to the variations in material,equipment and environment,the process variables monitored by sensors contain diverse data characteristics at different time scales or in multiple operating modes.Despite much progress in statistical learning and deep learning for fault recognition,most models are constrained by abundant diagnostic expertise,inefficient multiscale feature extraction and unruly multimode condition.To overcome the above issues,a novel fault diagnosis model called adaptive multiscale convolutional neural network(AMCNN)is developed in this paper.A new multiscale convolutional learning structure is designed to automatically mine multiple-scale features from time-series data,embedding the adaptive attention module to adjust the selection of relevant fault pattern information.The triplet loss optimization is adopted to increase the discrimination capability of the model under the multimode condition.The benchmarks CSTR simulation and Tennessee Eastman process are utilized to verify and illustrate the feasibility and efficiency of the proposed method.Compared with other common models,AMCNN shows its outstanding fault diagnosis performance and great generalization ability.展开更多
Longan(Dimocarpus longan Lour.),as an edible fruit and traditional Chinese medicine,has been consumed for thousands of years.Longan pulp has abundant nutritional phytochemicals such as protein,carbohydrate,vitamin C,p...Longan(Dimocarpus longan Lour.),as an edible fruit and traditional Chinese medicine,has been consumed for thousands of years.Longan pulp has abundant nutritional phytochemicals such as protein,carbohydrate,vitamin C,polysaccharides,polyphenols,which shows multiple biological activities including antioxidant,immunomodulatory and antitumor effects.Longan pericarp also demonstrates biological activities because of its rich content of polysaccharides and polyphenols.This review summarizes the bioactive compounds and bioactivities of longan pulp and aims to provide comprehensive information for future development of longan as a functional health food.展开更多
The aim of this work is to boost the combined hydrogen and added-values compounds generation(acetaldehyde, acetic acid and ethyl acetate) through ethanol electrochemical reforming using bimetallic anodes. In particula...The aim of this work is to boost the combined hydrogen and added-values compounds generation(acetaldehyde, acetic acid and ethyl acetate) through ethanol electrochemical reforming using bimetallic anodes. In particular, the influence of the secondary metal on the electrochemical performance as well as on the product distribution was studied. For that purpose, Pt X/C electrocatalysts(where X corresponds to Cu, Co, Ni and Ru) were synthesized by the modified polyol method and tested in both half-cell and proton exchange membrane(PEM) cell configurations. Characterization results showed that incorporation of Ni and Co into the Pt matrix enhances the morphological properties of the material, providing smaller crystallite sizes, higher active surface areas and hence, better dispersion when comparing to Ru and Cu-based electrocatalysts. Ethanol oxidation reaction(EOR) was evaluated by cyclic, linear voltammetry and chronopotentiometry assays. Pt Co/C and Pt Ni/C exhibited the highest electrocatalytic activity at high polarization levels, which translate into an improvement of more than 30%(up to 1050 m A cm^(-2)) in the hydrogen production and chemical yields. On the other hand, Pt Ru/C results more advantageous for a lower potential interval(<0.85 V) promoting the acetic acid production despite sacrificing ethanol conversion. Pt Cu/C presented the lowest results in both electrochemical performance and product distribution. Such differences in the electrochemical performance can be rationalized in terms of the synergistic effect between both metals(particle size distribution, grade of dispersion and hydrophilic behavior), which demonstrate that the incorporation of a different secondary metal plays an essential role in the EOR development.展开更多
The kinetics of the chemical leaching of copper from low grade ore in ferric sulfate media was investigated using the constrained least square optimization technique. The experiments were carried out for different par...The kinetics of the chemical leaching of copper from low grade ore in ferric sulfate media was investigated using the constrained least square optimization technique. The experiments were carried out for different particle sizes in both the reactor and column at constant oxidation-reduction potential （Eh）, pH values, and temperature. The main copper mineral was chalcopyrite. About 40% of Cu recovery is obtained after 7 d of reactor leaching at 85℃ using -0.5 mm size fraction, while the same recovery is obtained at 75℃ after 24 d. Also, about 23% of Cu recovery is obtained after 60 d of column leaching for ＋4--8 mm size fraction whereas the Cu recovery is as low as about 15% for ＋8--12.7 and ＋12.7--25 mm size fractions. A 4-stage model for chalcopyrite dissolution was used to explain the observed dissolution behaviors. The results show that thick over-layers of sulphur components cause the parabolic behavior of chalcopyrite dissolution and the precipitation of Fe3＋ plays the main role in chalcopyrite passivation. In the case of coarse particles, transformation from one stage to another takes a longer time, thus only two stages including the initial reaction on fresh surfaces and S0 deposition are observed.展开更多
Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its...Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its vanadium concentration. Most of these catalysts are usually supported on alumina containing a variable percentage of elements such as nickel or molybdenum. Hence these catalysts contain environmentally critical, and economically valuable metals such as molyb denum, vanadium, and, nickel. In this paper, a spent HDS catalyst was treated with caustic soda solution. Parameters such as temperature, time, and NaOH solution concentration have been studied thoroughly, in order to settle the appropriate conditions for the maximum recovery of molybdenum and vanadium. Under the best leaching conditions (20 %w NaOH, room temperature, 2 h) about 95% recovery of Mo and V was achieved, and the recovery of nickel obtained was of 99% in the form of NiAlO4.展开更多
This study investigates the potential of enhancing oil recovery from a Middle East heavy oil field via hot water injection followed by injection of a chemical surfactant and/or a biosurfactant produced by a Bacillus s...This study investigates the potential of enhancing oil recovery from a Middle East heavy oil field via hot water injection followed by injection of a chemical surfactant and/or a biosurfactant produced by a Bacillus subtilis strain which was isolated from oil-contaminated soil.The results reveal that the biosurfactant and the chemical surfactant reduced the residual oil saturation after a hot water flood.Moreover,it was found that the performance of the biosurfactant increased by mixing it with the chemical surfactant.It is expected that the structure of the biosurfactant used in this study was changed when mixed with the chemical surfactant as a probable synergetic effect of biosurfactant-chemical surfactants was observed on enhancing oil recovery,when used as a mixture,rather than alone.This work proved that it is more feasible to inject the biosurfactant as a blend with the chemical surfactant,at the tertiary recovery stage.This might be attributed to the fact that in the secondary mode,improvement of the macroscopic sweep efficiency is important,whereas in the tertiary recovery mode,the microscopic sweep efficiency matters mainly and it is improved by the biosurfactantchemical surfactant mixture.Also as evidenced by this study,the biosurfactant worked better than the chemical surfactant in reducing the residual heavy oil saturation after a hot water flood.展开更多
Structural, electronic, and optical properties of alloys BexMgl-xX （X = S, Se, Te） in the assortment 0 〈 x 〈 1 were theoretically reported for the first time in zinc-blende （ZB） phase. The calculations were carr...Structural, electronic, and optical properties of alloys BexMgl-xX （X = S, Se, Te） in the assortment 0 〈 x 〈 1 were theoretically reported for the first time in zinc-blende （ZB） phase. The calculations were carried out by using full-potential linearized augmented plane wave plus local orbitals （FP-LAPW＋lo） formalism contained by the framework of density functional theory （DFT）. Wu--Cohen （WC） generalized gradient approximation （GGA）, based on optimization energy, has been applied to calculate these theoretical results. In addition, we used Becke and Johnson （mBJ-GGA） potential, modified form of GGA functional, to calculate electronic structural properties up to a high precision degree. The alloys were composed with the concentrations x = 0.25, 0.5, and 0.75 in pursuance of ＇special quasi-random structures＇ （SQS） approach of Zunger for the restoration of disorder around the observed site of alloys in the first few shells. The structural parameters have been predicted by minimizing the total energy in correspondence of unit cell volume. Our alloys established direct band gap at different concentrations that make their importance in optically active materials. Furthermore, density of states was discussed in terms of the contribution of Be and Mg s and chalcogen （S, Se, and Te） s and p states and observed charge density helped us to investigate the bonding nature. By taking into consideration of immense importance in optoelectronics of these materials, the complex dielectric function was calculated for incident photon energy in the range 0--15 eV.展开更多
Due to the high salt content of coal chemical wastewater,pipeline fouling often occurs during wastewater treatment.Fouling will cause the diameter of the pipe to shrink or even block,which is not conducive to the safe...Due to the high salt content of coal chemical wastewater,pipeline fouling often occurs during wastewater treatment.Fouling will cause the diameter of the pipe to shrink or even block,which is not conducive to the safe and stable operation of the wastewater treatment process.In this paper,the experimental device was designed by using FLUENT software and the fouling deposition mechanisms at different flow velocities and different positions in a 90 deg bend were studied.The experimental results show that when the flow velocity is between 0.2 m·s^(-1)and 0.3 m·s^(-1),the thickness of fouling layer was positively correlated with the flow velocity;when the flow velocity is equal to 0.4 m·s^(-1),the formation of fouling is the most serious;when the flow velocity is between 0.4 m·s^(-1)and 0.7 m·s^(-1),the thickness of fouling layer was negative correlation with the flow velocity;with the increase of inlet velocity,the time for sediment point to develop into sediment surface is shortened.The fouling layer is easy to fall off because of the large shear force on the wall surface of the inner bend of the 90°elbow,so the density of sediment at this position is high.展开更多
At the global level, the augmenting presence of harmful algae blooms constitutes important dares to water treatment plants (WTPs). In WTPs, coagulation remains the primary process of the applied procedure to treat alg...At the global level, the augmenting presence of harmful algae blooms constitutes important dares to water treatment plants (WTPs). In WTPs, coagulation remains the primary process of the applied procedure to treat algae-contaminated water. Such a chemical process influences the following techniques;thus, regulating coagulation parameters to eliminate algae at the maximum degree without provoking cell deterioration is more than crucial. This work aims to review coagulation-founded methods for algae elimination. First, investigations concentrating on algae elimination using the chemical process are discussed. The introduction presents the widespread algae encountered in the water treatment field. Then, habitually utilized experimental techniques and emerging methods in coagulation investigations are summarized with typical findings. Next, the newest expansions in improved algae elimination, launched by electrochemically and ultrasonically-enhanced coagulation, are discussed. Workable thoughts for applying coagulation to eliminate algae in WTPs are also debated. The paper finishes by defining restrictions and dares related to the present literature and suggesting trends for subsequent studies. The charge neutralization mechanism efficiently removes solubilized microcystins (MCs), and enhanced coagulation configuration is also found to be more efficient for their removal. However, considerations should be taken to avert that the acid introduction has no unwanted effect in killing algae treatment to avoid the solubilized MCs level elevation. If such techniques are well-optimized and controlled, both algae and solubilized MCs could be efficaciously removed by ultrasound-enhanced coagulation and electrocoagulation/electrooxidation.展开更多
A trilogy review, based on more than 300 references, is used to underline three challenges facing 1) the supply of sustainable, durable and protected biosourced ingredients such as lipids, 2) the accounting for valuab...A trilogy review, based on more than 300 references, is used to underline three challenges facing 1) the supply of sustainable, durable and protected biosourced ingredients such as lipids, 2) the accounting for valuable bio-by-products, such as whey proteins that have added-value potential removing their environmental weight and 3) the practical reliable synthetic biology and evolutionary engineering that already serve as a technology and science basis to expand from, such as for biopolymer growth. Bioresources, which are the major topic of this review, must provide answers to several major challenges related to health, food, energy or chemistry of tomorrow. They offer a wide range of ingredients which are available in trees, plants, grasses, vegetables, algae, milk, food wastes, animal manures and other organic wastes. Researches in this domain must be oriented towards a bio-sustainable-economy based on new valuations of the potential of those renewable biological resources. This will aim at the substitution of fossil raw materials with renewable raw materials to ensure the sustainability of industrial processes by providing bioproducts through innovative processes using for instance micro-organisms and enzymes (the so-called white biotechnology). The final stage objective is to manufacture high value-added products gifted with the right set of physical, chemical and biological properties leading to particularly innovative applications. In this review, three examples are considered in a green context open innovation and bigger data environment. Two of them (lipids antioxidants and milk proteins) concern food industry while the third (biomonomers and corresponding bioplastics and derivatives) relates to biomaterials industry. Lipids play a crucial role in the food industry, but they are chemically unstable and very sensitive to atmospheric oxidation which leads to the formation of numerous by-compounds which have adverse effects on lipids quality attributes and on the nutritive value of meat. To overcome this problem, natural antioxidants, with a positive impact on the safety and acceptability of the food system, have been discovered and evaluated. In the same context, milk proteins and their derivatives are of great interest. They can be modified by enzymatic means leading to the formation of by-products that are able to increase their functionality and possible applications. They can also produce bioactive peptides, a field with almost unlimited research potential. On the other hand, biosourced chemicals and materials, mainly biomonomers and biopolymers, are already produced today. Metabolic engineering tools and strategies to engineer synthetic enzyme pathways are developed to manufacture, from renewable feedstocks, with high yields, a number of monomer building-block chemicals that can be used to produce replacements to many conventional plastic materials. Through those three examples this review aims to highlight recent and important advancements in production, modification and applications of the studied bioproducts. Bigger data analysis and artificial intelligence may help reweight practical and theoretical observations and concepts in these fields;helping to cross the boarders of expert traditional exploration fields and sometime fortresses.展开更多
Air pollution has become a major problem in urban areas due to increasing industrialization and urbanization.In this study ambient concentrations of PM1 and metal concentrations as well as source contributions were id...Air pollution has become a major problem in urban areas due to increasing industrialization and urbanization.In this study ambient concentrations of PM1 and metal concentrations as well as source contributions were identified and quantified by using Positive Matrix Factorization(PMF)in receptor modeling in the Metropolitan Area of Porto Alegre,Brazil.The PM1 samples were collected on PTFE filters from December 2012 to December 2014 in two sampling sites.Major ion and trace element concentrations were assessed.The average concentrations were 12.8 and 15.2μg/m^(3) for Canoas and Sapucaia do Sul sites,respectively.Major ion contributions of PM1 were secondary pollutants such as sulfate and nitrate.Trace elements,especially Cu,Pb,Zn,Cd,and Ni also made important contributions which are directly associated with anthropogenic contributions.Our results show significantly higher levels in winter than in summer.Most of the PM1 and the analyzed PM species and elements originated from anthropogenic sources,especially road traffic,combustion processes and industrial activities,which are grouped in 7 major contributing sources.A back-trajectory analysis showed that the long-range transport of pollutants was not relevant in relation to the contribution to PM1 and metal concentrations.This work highlights the importance of urban planning to reduce human health exposure to traffic and industrial emissions,combined with awareness-raising actions for citizens concerning the impact of indoor sources.展开更多
The investigation focuses on evaluating the effect of varying % of Red Mud (RM) reinforcement with Ordinary Portland Slag Cement (OPSC). Characterisation is done by adding 10%, 20%, 30%, 40% and 50% of RM by weight to...The investigation focuses on evaluating the effect of varying % of Red Mud (RM) reinforcement with Ordinary Portland Slag Cement (OPSC). Characterisation is done by adding 10%, 20%, 30%, 40% and 50% of RM by weight to OPSC. RM + OPSC composite mortars are made in an 8.5 × 5 × 4 cm<sup>3</sup> cast iron mould with external vibration keeping water-binder ratio 0.4 by weight. The mortars are cured in water for 28 days and their physio-chemical characteristics are investigated. Mortar performances like compressive strength, hardness, XRD, FTIR, SEM are diagnosed. The composite mortars cementing properties are compared with original OPSC. The result reveals the augmentation of RM with OPSC increases the hydration capacity of OPSC with improved compressive strength. The experimental optimization shows a maximum value up to 10% - 20% OPSC can be replaced by RM as filling material.展开更多
基金the supports of the National Science Foundation of China (22008130, 22025801)the China Postdoctoral Science Foundation (2020M682124)+1 种基金the Qingdao Postdoctoral Researchers Applied Research Project Foundation (RZ2000001426)the Scientific Research Foundation for Youth Scholars from Qingdao University (DC1900014265) for this work
文摘The concept of“carbon neutrality”poses a huge challenge for chemical engineering and brings great opportunities for boosting the development of novel technologies to realize carbon offsetting and reduce carbon emissions.Developing high-efficient,low-cost,energy-efficient and eco-friendly microfluidicbased microchemical engineering is of great significance.Such kind of“green microfluidics”can reduce carbon emissions from the source of raw materials and facilitate controllable and intensified microchemical engineering processes,which represents the new power for the transformation and upgrading of chemical engineering industry.Here,a brief review of green microfluidics for achieving carbon neutral microchemical engineering is presented,with specific discussions about the characteristics and feasibility of applying green microfluidics in realizing carbon neutrality.Development of green microfluidic systems are categorized and reviewed,including the construction of microfluidic devices by bio-based substrate materials and by low carbon fabrication methods,and the use of more biocompatible and nondestructive fluidic systems such as aqueous two-phase systems(ATPSs).Moreover,low carbon applications benefit from green microfluidics are summarized,ranging from separation and purification of biomolecules,high-throughput screening of chemicals and drugs,rapid and cost-effective detections,to synthesis of fine chemicals and novel materials.Finally,challenges and perspectives for further advancing green microfluidics in microchemical engineering for carbon neutrality are proposed and discussed.
基金We would like to acknowledge the supports from the National Natural Science Foundation of China(21776150)and the State Key Laboratory of Chemical Engineering(SKL-ChE-20Z01).
文摘Electrochemical methods are environmentally friendly and have unique advantages in the synthesis of organic chemicals.However,their implementation is limited due to the complex transport problems posed by traditional electrochemical reactors.Recently,the application of microreaction technology in electrosynthesis studies has reduced the transport distance of ions and increased the specific surface area of electrodes,leading to efficient,successive,and easily scaled-up electrosynthesis technologies.In this review article,engineering advantages of using microchannels in electrosynthesis are discussed from process enhancement perspective.Flow patterns and mass transfer behaviors in recently reported electrochemical microreactors are analyzed,and prototypes for the reactor scale-up are reviewed.As a relatively new research area,many scientific rules and engineering features of electrosynthesis in microreactors require elucidation.Potential research foci,considered crucial for the development of novel electrosynthesis technology,are therefore proposed.
文摘Chemical industry project management involves complex decision making situations that require discerning abilities and methods to make sound decisions. Chemical engineers as project managers are faced with decision environments and problems in chemical industry projects that are complex. Multiple-criteria decision making （MCDM） approaches are major parts of decision theory and analysis. This paper presents all of MCDM approaches for use in chemical engineering management decisions. In this work, case study is Research and Development （R＆D） project selection in chemical industry. The ability to make sound decisions is very important to success of R＆D projects. It is hoped that this work will provide a ready reference on MCDM and this will encourage the application of the MCDM in chemical engineering management.
基金support from Generalitat Valenciana under Pla Complementari“Programa de Materials Avanc¸ats”,2022(grant number MFA/2022/030)Ministerio de Ciencia,Innovaci´on y Universidades(Spain)(grant number MCIN/AEI/10.13039/501100011033)+1 种基金support from UJI(UJI-2023-16 and GACUJIMC/2023/08)Generalitat Valenciana through FPI Fellowship Program(grant numbers ACIF/2020/294 and CIACIF/2021/050).
文摘This study demonstrates the successful fabrication of solid-state bilayers using LiFePO_(4)(LFP)cathodes and Li_(1.3)Al_(0.3)Ti_(1.7)(PO_(4))_(3)(LATP)-based Composite Solid Electrolytes(CSEs)via Cold Sintering Process(CSP).By optimizing the sintering pressure,it is achieved an intimate contact between the cathode and the solid electrolyte,leading to an enhanced electrochemical performance.Bilayers cold sintered at 300 MPa and a low-sintering temperature of 150℃exhibit high ionic conductivities(0.5 mS cm^(-1))and stable specific capacities at room temperature(160.1 mAh g^(-1)LFP at C/10 and 75.8 mAh g^(-1)_(LFP)at 1 C).Moreover,an operando electrochemical impedance spectroscopy(EIS)technique is employed to identify limiting factors of the bilayer kinetics and to anticipate the overall electrochemical behavior.Results suggest that capacity fading can occur in samples prepared with high sintering pressures due to a volume reduction in the LFP crystalline cell.This work demonstrates the potential of CSP to produce straightforward high-performance bilayers and introduces a valuable non-destructive instrument for understanding and avoiding degradation in solid-state lithium-based batteries.
基金support from the Scientific Research Fund of Zhejiang Provincial Education Department(Y202353855)the Zhejiang Provincial Key R&D Project(2021C01056)+1 种基金the Programme of Introducing Talents of Discipline to Universities(No.D17008)the National Natural Science Foundation of China(22208312).
文摘Three large π-conjugated and imine-based COFs,named TFP-TAB,TFP-TTA,and TTA-TTB,were synthesized via the ordered incorporation of benzene and triazine rings in the same host framework to study how the structural units affect the efficiency of CO_(2)photoreduction.Results from both experiments and density-functional theory(DFT)calculations indicate the separation and transfer of the photoinduced charges is highly related to the triazine-N content and the conjugation degree in the skeletons of COFs.High-efficiency CO_(2)photoreduction can be achieved by rationally adjusting the number and position of both benzene and triazine rings in the COFs.Specifically,TTA-TTB,with orderly interlaced triazine-benzene heterojunctions,can suppress the recombination probability of electrons and holes,which effectively immobilizes the key species(COOH)and lowers the free energy change of the potential-determining step,and thus exhibits a superior visible-light-induced photocatalytic activity that yields 121.7 μmol HCOOH g^(-1)h^(-1).This research,therefore,helps to elucidate the effects of the different structural blocks in COFs on inherent heterogeneous photocatalysis for CO_(2)reduction at a molecular level.
基金financially supported by East-West Cooperation Project of Ningxia Key R&D Plan(2017BY064)National First-rate Discipline Construction Project of Ningxia(NXYLXK2017A04)。
文摘Zero liquid discharge(ZLD)treatment and reuse equipment of high salinity wastewater in coal-chemical industry often occur in various types of blockage problems because of high salt content,affecting the long-term stability of the device.In this study,the effects of solution temperature,steel,reaction time and wall roughness on fouling were investigated.The changes in the contents of fouling and fouling substances were qualitatively and quantitatively analyzed by XRD and EDS respectively,and the formation of scale was observed by SEM.The results show that with temperature increasing,Q235 steel is the most difficult to scale.Scaling rate of all salt scales reaches a maximum after 12 h,and the fouling rate decreases significantly from 12 to 48 h.It gradually stabilizes at 48 to 96 h.With the roughness increasing,the thickness of fouling layer increases,and a linear relationship is presented for 1 to 10 h.By comparing actual and simulated wastewater scaling rates,the relationship between actual and simulated wastewater scaling rates is y=ax-0.494.The composition of the scale was analyzed,calcium carbonate is the main product and increases with fouling time.Based on the above-mentioned results combining literatures,the hybrid prediction model with calcium carbonate as the main product is put forward.It is discussed microscopically that calcium carbonate is converted from aragonite and vaterite in a thermodynamically metastable state to calcite in a thermodynamically stable state.
文摘Density functional theory is applied to predicting the structures and electrostatic potentials of planar electrochemical surfaces within the framework of the restricted primitive model where small ions are represented by charged hard spheres of equal diameter and the solvent is assumed to be a continuous dielectric medium. The hard-sphere contribution to the excess Helmholtz energy functional is evaluated using the modified fundamentalmeasure theory and the electrostatic contribution is obtained from the quadratic functional Taylor expansion using the second-order direct correlation function from the mean-spherical approximation. Numerical results for the ionic density profiles and the mean electrostatic potentials near a planar surface of various charge densities are in excellent agreement with molecular simulations. In contrast to the modified Gouy-Chapman theory, the present density functional theory correctly predicts the second layer formation and charge inversion of charged surfaces as observed in simulations and in experiments. The theory has also been tested with the zeta potentials of positively charged polystyrene particles in aqueous solutions of KBr. Good agreement is achieved between the calculated and experimental results.
文摘Development of a predictive tool for H_2S solubility estimation can be very helpful in gas sweetening industry. Experimental databases on H_2 S solubility were rarely available, so as reliable predictive models. Thus, in this study the H_2 S solubility database was established, and then a Least-Squares Support Vector Machine(LSSVM) approach based on the established database is proposed. Group contribution method was also applied to eliminate the model's dependence on experimental data. Accordingly, our proposed LSSVM model can predict H_2 S solubility as a function of temperature, pressure, and 15 different chemical structures of Ionic liquids(ILs). Root Mean Square Error(RMSE) and coefficient of determination(R^2) are 0.0122 and 0.9941, respectively. Moreover, comparison of our model with other existing models showed its reliability for H_2 S solubility in ILs. This can be very useful for engineers dealing with gas sweetening process in different applications of analysis, simulation, and designation.
基金support from the National Science and Technology Innovation 2030 Major Project of the Ministry of Science and Technology of China(2018AAA0101605)the National Natural Science Foundation of China(21878171)。
文摘Intelligent fault recognition techniques are essential to ensure the long-term reliability of manufacturing.Due to the variations in material,equipment and environment,the process variables monitored by sensors contain diverse data characteristics at different time scales or in multiple operating modes.Despite much progress in statistical learning and deep learning for fault recognition,most models are constrained by abundant diagnostic expertise,inefficient multiscale feature extraction and unruly multimode condition.To overcome the above issues,a novel fault diagnosis model called adaptive multiscale convolutional neural network(AMCNN)is developed in this paper.A new multiscale convolutional learning structure is designed to automatically mine multiple-scale features from time-series data,embedding the adaptive attention module to adjust the selection of relevant fault pattern information.The triplet loss optimization is adopted to increase the discrimination capability of the model under the multimode condition.The benchmarks CSTR simulation and Tennessee Eastman process are utilized to verify and illustrate the feasibility and efficiency of the proposed method.Compared with other common models,AMCNN shows its outstanding fault diagnosis performance and great generalization ability.
基金This project was supported by the National Natural Science Foundation of China(No.31570348).
文摘Longan(Dimocarpus longan Lour.),as an edible fruit and traditional Chinese medicine,has been consumed for thousands of years.Longan pulp has abundant nutritional phytochemicals such as protein,carbohydrate,vitamin C,polysaccharides,polyphenols,which shows multiple biological activities including antioxidant,immunomodulatory and antitumor effects.Longan pericarp also demonstrates biological activities because of its rich content of polysaccharides and polyphenols.This review summarizes the bioactive compounds and bioactivities of longan pulp and aims to provide comprehensive information for future development of longan as a functional health food.
基金We gratefully acknowledge the Spanish Ministry of Science and Innovation(project PID2019-107499RB-100 and FPI grant BES-2017-081181)for the financial support.
文摘The aim of this work is to boost the combined hydrogen and added-values compounds generation(acetaldehyde, acetic acid and ethyl acetate) through ethanol electrochemical reforming using bimetallic anodes. In particular, the influence of the secondary metal on the electrochemical performance as well as on the product distribution was studied. For that purpose, Pt X/C electrocatalysts(where X corresponds to Cu, Co, Ni and Ru) were synthesized by the modified polyol method and tested in both half-cell and proton exchange membrane(PEM) cell configurations. Characterization results showed that incorporation of Ni and Co into the Pt matrix enhances the morphological properties of the material, providing smaller crystallite sizes, higher active surface areas and hence, better dispersion when comparing to Ru and Cu-based electrocatalysts. Ethanol oxidation reaction(EOR) was evaluated by cyclic, linear voltammetry and chronopotentiometry assays. Pt Co/C and Pt Ni/C exhibited the highest electrocatalytic activity at high polarization levels, which translate into an improvement of more than 30%(up to 1050 m A cm^(-2)) in the hydrogen production and chemical yields. On the other hand, Pt Ru/C results more advantageous for a lower potential interval(<0.85 V) promoting the acetic acid production despite sacrificing ethanol conversion. Pt Cu/C presented the lowest results in both electrochemical performance and product distribution. Such differences in the electrochemical performance can be rationalized in terms of the synergistic effect between both metals(particle size distribution, grade of dispersion and hydrophilic behavior), which demonstrate that the incorporation of a different secondary metal plays an essential role in the EOR development.
基金the support of Research & Development Division of Sarcheshmeh Copper Complex (Kerman/ Iran) and Tarbiat Modares University(Tehran/ Iran)
文摘The kinetics of the chemical leaching of copper from low grade ore in ferric sulfate media was investigated using the constrained least square optimization technique. The experiments were carried out for different particle sizes in both the reactor and column at constant oxidation-reduction potential （Eh）, pH values, and temperature. The main copper mineral was chalcopyrite. About 40% of Cu recovery is obtained after 7 d of reactor leaching at 85℃ using -0.5 mm size fraction, while the same recovery is obtained at 75℃ after 24 d. Also, about 23% of Cu recovery is obtained after 60 d of column leaching for ＋4--8 mm size fraction whereas the Cu recovery is as low as about 15% for ＋8--12.7 and ＋12.7--25 mm size fractions. A 4-stage model for chalcopyrite dissolution was used to explain the observed dissolution behaviors. The results show that thick over-layers of sulphur components cause the parabolic behavior of chalcopyrite dissolution and the precipitation of Fe3＋ plays the main role in chalcopyrite passivation. In the case of coarse particles, transformation from one stage to another takes a longer time, thus only two stages including the initial reaction on fresh surfaces and S0 deposition are observed.
文摘Large quantities of spent hydrodesulfurization (HDS) catalysts are available from petrochemical industry. Disposal of spent catalyst is a problem as it falls under the category of hazardous industrial waste due to its vanadium concentration. Most of these catalysts are usually supported on alumina containing a variable percentage of elements such as nickel or molybdenum. Hence these catalysts contain environmentally critical, and economically valuable metals such as molyb denum, vanadium, and, nickel. In this paper, a spent HDS catalyst was treated with caustic soda solution. Parameters such as temperature, time, and NaOH solution concentration have been studied thoroughly, in order to settle the appropriate conditions for the maximum recovery of molybdenum and vanadium. Under the best leaching conditions (20 %w NaOH, room temperature, 2 h) about 95% recovery of Mo and V was achieved, and the recovery of nickel obtained was of 99% in the form of NiAlO4.
基金Majesty Research Fund (SR/SCI/BIOL/08/01),Sultan Qaboos University,Oman and the Petroleum Development of Oman (CR/SCI/BIOL/07/02) for the research grants
文摘This study investigates the potential of enhancing oil recovery from a Middle East heavy oil field via hot water injection followed by injection of a chemical surfactant and/or a biosurfactant produced by a Bacillus subtilis strain which was isolated from oil-contaminated soil.The results reveal that the biosurfactant and the chemical surfactant reduced the residual oil saturation after a hot water flood.Moreover,it was found that the performance of the biosurfactant increased by mixing it with the chemical surfactant.It is expected that the structure of the biosurfactant used in this study was changed when mixed with the chemical surfactant as a probable synergetic effect of biosurfactant-chemical surfactants was observed on enhancing oil recovery,when used as a mixture,rather than alone.This work proved that it is more feasible to inject the biosurfactant as a blend with the chemical surfactant,at the tertiary recovery stage.This might be attributed to the fact that in the secondary mode,improvement of the macroscopic sweep efficiency is important,whereas in the tertiary recovery mode,the microscopic sweep efficiency matters mainly and it is improved by the biosurfactantchemical surfactant mixture.Also as evidenced by this study,the biosurfactant worked better than the chemical surfactant in reducing the residual heavy oil saturation after a hot water flood.
基金the Deanship of Scientific Research at King Saud University for funding this Research group No.RG 1435-004
文摘Structural, electronic, and optical properties of alloys BexMgl-xX （X = S, Se, Te） in the assortment 0 〈 x 〈 1 were theoretically reported for the first time in zinc-blende （ZB） phase. The calculations were carried out by using full-potential linearized augmented plane wave plus local orbitals （FP-LAPW＋lo） formalism contained by the framework of density functional theory （DFT）. Wu--Cohen （WC） generalized gradient approximation （GGA）, based on optimization energy, has been applied to calculate these theoretical results. In addition, we used Becke and Johnson （mBJ-GGA） potential, modified form of GGA functional, to calculate electronic structural properties up to a high precision degree. The alloys were composed with the concentrations x = 0.25, 0.5, and 0.75 in pursuance of ＇special quasi-random structures＇ （SQS） approach of Zunger for the restoration of disorder around the observed site of alloys in the first few shells. The structural parameters have been predicted by minimizing the total energy in correspondence of unit cell volume. Our alloys established direct band gap at different concentrations that make their importance in optically active materials. Furthermore, density of states was discussed in terms of the contribution of Be and Mg s and chalcogen （S, Se, and Te） s and p states and observed charge density helped us to investigate the bonding nature. By taking into consideration of immense importance in optoelectronics of these materials, the complex dielectric function was calculated for incident photon energy in the range 0--15 eV.
基金financially supported by the Natural Science Foundation of Ningxia Hui Autonomous Region(2020AAC03025)Undergraduate Training Programs for Innovation(2019107490001)+1 种基金East-West Cooperation Project of Ningxia Key R&D Plan(2017BY064)National First-rate Discipline Construction Project of Ningxia(NXYLXK2017A04)
文摘Due to the high salt content of coal chemical wastewater,pipeline fouling often occurs during wastewater treatment.Fouling will cause the diameter of the pipe to shrink or even block,which is not conducive to the safe and stable operation of the wastewater treatment process.In this paper,the experimental device was designed by using FLUENT software and the fouling deposition mechanisms at different flow velocities and different positions in a 90 deg bend were studied.The experimental results show that when the flow velocity is between 0.2 m·s^(-1)and 0.3 m·s^(-1),the thickness of fouling layer was positively correlated with the flow velocity;when the flow velocity is equal to 0.4 m·s^(-1),the formation of fouling is the most serious;when the flow velocity is between 0.4 m·s^(-1)and 0.7 m·s^(-1),the thickness of fouling layer was negative correlation with the flow velocity;with the increase of inlet velocity,the time for sediment point to develop into sediment surface is shortened.The fouling layer is easy to fall off because of the large shear force on the wall surface of the inner bend of the 90°elbow,so the density of sediment at this position is high.
文摘At the global level, the augmenting presence of harmful algae blooms constitutes important dares to water treatment plants (WTPs). In WTPs, coagulation remains the primary process of the applied procedure to treat algae-contaminated water. Such a chemical process influences the following techniques;thus, regulating coagulation parameters to eliminate algae at the maximum degree without provoking cell deterioration is more than crucial. This work aims to review coagulation-founded methods for algae elimination. First, investigations concentrating on algae elimination using the chemical process are discussed. The introduction presents the widespread algae encountered in the water treatment field. Then, habitually utilized experimental techniques and emerging methods in coagulation investigations are summarized with typical findings. Next, the newest expansions in improved algae elimination, launched by electrochemically and ultrasonically-enhanced coagulation, are discussed. Workable thoughts for applying coagulation to eliminate algae in WTPs are also debated. The paper finishes by defining restrictions and dares related to the present literature and suggesting trends for subsequent studies. The charge neutralization mechanism efficiently removes solubilized microcystins (MCs), and enhanced coagulation configuration is also found to be more efficient for their removal. However, considerations should be taken to avert that the acid introduction has no unwanted effect in killing algae treatment to avoid the solubilized MCs level elevation. If such techniques are well-optimized and controlled, both algae and solubilized MCs could be efficaciously removed by ultrasound-enhanced coagulation and electrocoagulation/electrooxidation.
文摘A trilogy review, based on more than 300 references, is used to underline three challenges facing 1) the supply of sustainable, durable and protected biosourced ingredients such as lipids, 2) the accounting for valuable bio-by-products, such as whey proteins that have added-value potential removing their environmental weight and 3) the practical reliable synthetic biology and evolutionary engineering that already serve as a technology and science basis to expand from, such as for biopolymer growth. Bioresources, which are the major topic of this review, must provide answers to several major challenges related to health, food, energy or chemistry of tomorrow. They offer a wide range of ingredients which are available in trees, plants, grasses, vegetables, algae, milk, food wastes, animal manures and other organic wastes. Researches in this domain must be oriented towards a bio-sustainable-economy based on new valuations of the potential of those renewable biological resources. This will aim at the substitution of fossil raw materials with renewable raw materials to ensure the sustainability of industrial processes by providing bioproducts through innovative processes using for instance micro-organisms and enzymes (the so-called white biotechnology). The final stage objective is to manufacture high value-added products gifted with the right set of physical, chemical and biological properties leading to particularly innovative applications. In this review, three examples are considered in a green context open innovation and bigger data environment. Two of them (lipids antioxidants and milk proteins) concern food industry while the third (biomonomers and corresponding bioplastics and derivatives) relates to biomaterials industry. Lipids play a crucial role in the food industry, but they are chemically unstable and very sensitive to atmospheric oxidation which leads to the formation of numerous by-compounds which have adverse effects on lipids quality attributes and on the nutritive value of meat. To overcome this problem, natural antioxidants, with a positive impact on the safety and acceptability of the food system, have been discovered and evaluated. In the same context, milk proteins and their derivatives are of great interest. They can be modified by enzymatic means leading to the formation of by-products that are able to increase their functionality and possible applications. They can also produce bioactive peptides, a field with almost unlimited research potential. On the other hand, biosourced chemicals and materials, mainly biomonomers and biopolymers, are already produced today. Metabolic engineering tools and strategies to engineer synthetic enzyme pathways are developed to manufacture, from renewable feedstocks, with high yields, a number of monomer building-block chemicals that can be used to produce replacements to many conventional plastic materials. Through those three examples this review aims to highlight recent and important advancements in production, modification and applications of the studied bioproducts. Bigger data analysis and artificial intelligence may help reweight practical and theoretical observations and concepts in these fields;helping to cross the boarders of expert traditional exploration fields and sometime fortresses.
文摘Air pollution has become a major problem in urban areas due to increasing industrialization and urbanization.In this study ambient concentrations of PM1 and metal concentrations as well as source contributions were identified and quantified by using Positive Matrix Factorization(PMF)in receptor modeling in the Metropolitan Area of Porto Alegre,Brazil.The PM1 samples were collected on PTFE filters from December 2012 to December 2014 in two sampling sites.Major ion and trace element concentrations were assessed.The average concentrations were 12.8 and 15.2μg/m^(3) for Canoas and Sapucaia do Sul sites,respectively.Major ion contributions of PM1 were secondary pollutants such as sulfate and nitrate.Trace elements,especially Cu,Pb,Zn,Cd,and Ni also made important contributions which are directly associated with anthropogenic contributions.Our results show significantly higher levels in winter than in summer.Most of the PM1 and the analyzed PM species and elements originated from anthropogenic sources,especially road traffic,combustion processes and industrial activities,which are grouped in 7 major contributing sources.A back-trajectory analysis showed that the long-range transport of pollutants was not relevant in relation to the contribution to PM1 and metal concentrations.This work highlights the importance of urban planning to reduce human health exposure to traffic and industrial emissions,combined with awareness-raising actions for citizens concerning the impact of indoor sources.
文摘The investigation focuses on evaluating the effect of varying % of Red Mud (RM) reinforcement with Ordinary Portland Slag Cement (OPSC). Characterisation is done by adding 10%, 20%, 30%, 40% and 50% of RM by weight to OPSC. RM + OPSC composite mortars are made in an 8.5 × 5 × 4 cm<sup>3</sup> cast iron mould with external vibration keeping water-binder ratio 0.4 by weight. The mortars are cured in water for 28 days and their physio-chemical characteristics are investigated. Mortar performances like compressive strength, hardness, XRD, FTIR, SEM are diagnosed. The composite mortars cementing properties are compared with original OPSC. The result reveals the augmentation of RM with OPSC increases the hydration capacity of OPSC with improved compressive strength. The experimental optimization shows a maximum value up to 10% - 20% OPSC can be replaced by RM as filling material.
