A novel treating technology for nitrogen removal from soybean wastewater was studied. The process for nitrogen removal was achieved by alternating aeration and mixing, combined with real\|time control strategies. Resu...A novel treating technology for nitrogen removal from soybean wastewater was studied. The process for nitrogen removal was achieved by alternating aeration and mixing, combined with real\|time control strategies. Results showed that the COD and total nitrogen removal rates are more than 90% and 92% at COD and total nitrogen loads of 1\^0-1\^2 kg COD/(kgMLSS·d) and 0\^20-0\^27 kg TN/(kgMLSS·d), respectively. In addition, it could improve sludge settling property. SVI value is less than 70 g/ml during the whole cycles. The method not only may be adapted to treat soybean wastewater with high nitrogen, but also may be applied to treat other high nitrogen wastewater.展开更多
Control of sludge age and mixed liquid suspended solids concentration in the activated sludge process is critical for ensuring effective wastewater treatment. A nonlinear dynamic model for a step-feed activated sludge...Control of sludge age and mixed liquid suspended solids concentration in the activated sludge process is critical for ensuring effective wastewater treatment. A nonlinear dynamic model for a step-feed activated sludge process was developed in this study. The system is based on the control of the sludge age and mixed liquor suspended solids in the aerator of last stage by adjusting the sludge recycle and wastage flow rates respectively. The simulation results showed that the sludge age remained nearly constant at a value of 16 d in the variation of the influent characteristics. The mixed liquor suspended solids in the aerator of last stage were also maintained to a desired value of 2500 g/m3 by adjusting wastage flow rates.展开更多
In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical pr...In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical probes and an EKTAPRO 1000 high speed motion analyzer. It demonstrates that the radial profile of slug flow void fraction is parabolic. Influenced by the falling liquid film, the radial profile curve of liquid slug void fraction in the wake region is also parabolic. Since fully turbulent velocity distribution is built up in the developed region,the void fraction profile in this region is the saddle type. At given superficial liquid velocity, the liquid slug void fraction increases with gas velocity. The radial profiles of liquid slug void fraction at different axial locations are all saddle curves, but void fraction is obviously high around the centerline in the entrance region. The nearer the measuring station is from the entrance, the farther the peak location is away from the wall.展开更多
AIM:Systemic treatment with epidermal growth factor (EGF)leads to growth of all parts of the small intestine in normal functioning rats. In this study, we investigated the effect of this growth process on morphometric...AIM:Systemic treatment with epidermal growth factor (EGF)leads to growth of all parts of the small intestine in normal functioning rats. In this study, we investigated the effect of this growth process on morphometric and biomechanical parameters of ileum.METHODS: Rats were treated with EGF (150 μg@kg-1day-1)or placebo via osmotic minipumps for 2, 4, 7, and 14 days.A segment of ileum was removed. The morphology at noload state and zero-stress state was measured and passive biomechanical properties were assessed using a biaxial test machine (combined inflation and axial stretching).RESULTS: The ileum weight increased after EGF administration. After 4 days' EGF treatment, the wall thickness was increased. Significantly smaller inner perimeters were seen in 4 day and 7 day EGF treatment groups. The opening angle and residual strain began to increase after 7 days' EGF treatment. Wall stiffness, evaluated from the stress-strain curves, showed a continuous decrease in circumferential direction during the first 7 days' EGF treatment. The longitudinal stiffness increased during the first 7 days. The stress-strain curves for both circumferential and longitudinal direction tended to shift back to normal 14days after starting EGF administration.CONCLUSION: EGF can cause significant changes both in the morphology and in the passive mechanical properties of the rat ileum.展开更多
Semi-empirical molecular orbital calculations were performed on heterocyclic aromatic amines(HCAs). The relationship between the structures and the carcinogenicities can be rationally elucidated by the models based on...Semi-empirical molecular orbital calculations were performed on heterocyclic aromatic amines(HCAs). The relationship between the structures and the carcinogenicities can be rationally elucidated by the models based on the metabolism of HCAs and the Di-region theory. The degree of easiness for the formation of Di-region electrophilic centers determines the carcinogenic activity. There is a good linear relationship between the observed carcinogenicities and the PM3 calculated parameters, with r=0.973 and F=29.8>F ** 0.01 .展开更多
Based on generalized Apell-Chetaev constraint conditions and to take the inherent constrains for singular Lagrangian into account,the generalized canonical equations for a general mechanical system with a singular hig...Based on generalized Apell-Chetaev constraint conditions and to take the inherent constrains for singular Lagrangian into account,the generalized canonical equations for a general mechanical system with a singular higher-order Lagrangian and subsidiary constrains are formulated. The canonical symmetries in phase space for such a system are studied and Noether theorem and its inversion theorem in the generalized canonical formalism have been established.展开更多
AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angle...AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angles of collagen fiber and the pressure it undergoes.METHODS: A kind of 2-dimensional visible quantitative analyzing technique was described. Digital image-processing method was utilized to determine the angle of collagen fiber in parenchyma according to the changes of area analyzed and further to investigate quantitatively the distribution of collagen fiber. A series of intestinal slice′s images preprocessed by polarized light were obtained with electron microscope,and they were processed to unify each pixel. The approximate angles between collagen fibers were obtained via analyzing the images and their corresponding polarized light. The relationship between the angles of collagen fiber and the pressure it undergoes were statistically summarized.RESULTS: The angle of collagen fiber in intestinal tissue was obtained with the quantitative analyzing method of calculating the ratio of different pixels. For the same slice,with polarized light angle′s variation, the corresponding ratio of different pixels was also changed; for slices under different pressures, the biggest ratio of collagen fiber area was changed either.CONCLUSION: This study suggests that the application of stress on the intestinal tissue will change the angle and content of collagen fiber. The method of calculating ratios of different pixel values to estimate collagen fiber angle was practical and reliable. The quantitative analysis used in the present study allows a larger area of soft tissue to be analyzed with relatively low cost and simple equipment.展开更多
In the present research Monte Carlo technique was used to simulate the grain growth in heat-affected zone(HAZ) of an ultrafine grain steel. An experimental data based (EBD) model proposed by Gao was used to establish ...In the present research Monte Carlo technique was used to simulate the grain growth in heat-affected zone(HAZ) of an ultrafine grain steel. An experimental data based (EBD) model proposed by Gao was used to establish the relation between tMCS and real time temperature kinetics in our simulation. The simulations give out the evolution of grain structure and grain size distribution in HAZ of the ultrafine grain steel. A Microsoft Window based on computer program for the simulation of grain growth in the HAZ of weldment in three dimensions has been developed using Monte Carlo technique. For the system, inputting the temperature field data and material properties, the evolution of grain structure, both image of simulated grain structure and numerical datum reflecting grain size distribution can be produced by the program. The system was applied to the ultrafine grain steel welding, and the simulated results show that the ultrafine grain steel has large tendency of grain growth.展开更多
A new genetic algorithm (GA) is developed. It features three new operations: restoration, reconstruction and recording the better, so as to produce a limited monotonic sequence of fitness value, to realize a globally ...A new genetic algorithm (GA) is developed. It features three new operations: restoration, reconstruction and recording the better, so as to produce a limited monotonic sequence of fitness value, to realize a globally optimal choosing, and to converge to a globally optimal solution through a perfectly stochastic process. Practical examples are given to illustrate the superiority of this new GA.展开更多
The effect of seawater salinity on nitrite accumulation in short-range nitrification to nitrite as the end product was studied by using a SBR. Experimental results indicated that the growth of nitrobacteria was inhibi...The effect of seawater salinity on nitrite accumulation in short-range nitrification to nitrite as the end product was studied by using a SBR. Experimental results indicated that the growth of nitrobacteria was inhibited and very high levels of nitrite accumulation at different salinities were achieved under the conditions of 25—28℃, pH 7.5? ?.0 , and the influent ammonia nitrogen of 40—70 mg/L when seawater flow used to flush toilet was less than 35%(salinity 12393 mg/L, Cl - 6778 mg/L) of total domestic wastewater flow, which is mainly ascribed to much high chlorine concentration of seawater. Results showed that high seawater salinity is available for short-range nitrification to nitrite as the end product. When the seawater flow used to flush toilet accounting for above 70% of the total domestic wastewater flow, the removal efficiency of ammonia was still above 80% despite the removal of organics declined obviously(less than 60%). It was found that the effect of seawater salinity on the removal of organics was negative rather than positive one as shown for ammonia removal.展开更多
Welded joint is a mechanical heterogeneous body, and mechanical heterogeneity has great effect on dynamic fracture behaviour of welded joints. In the present investigation, dynamic response curve and dynamic J-integra...Welded joint is a mechanical heterogeneous body, and mechanical heterogeneity has great effect on dynamic fracture behaviour of welded joints. In the present investigation, dynamic response curve and dynamic J-integral of practical undermatched welded joint and whole base and whole weld three-point-bend (TPB) models containing longitudinal crack are com- puted. Dynamic J-integral is evaluated using virtual crack extension (VCE) method and the computation is performed using MARC finite element code. Because of the effect of inertia, dynamic load response curve of computed model waves periodically. Dynamic J-integral evaluated by VCE method is path independent. The effect of inertia has little influence on dynamic J-integral curve. The value of dynamic J-integral of undermatched welded joint is lower than that of whole base metal and higher than that of whole weld metal. The results establish the foundation of safety evaluation for dynamic loaded welded structures.展开更多
Based on the canonical action,a generalized canonical first Noether theorem and Poicare-Cartan integralinvariant for a system with a singular high-order Lagrangian are derived.It is worth while to point out that the c...Based on the canonical action,a generalized canonical first Noether theorem and Poicare-Cartan integralinvariant for a system with a singular high-order Lagrangian are derived.It is worth while to point out that the constraints are invariant under the total variation of canonical variables including time.We can also deduce the result,which differs from the previous work to reuire that the constraints are invariant under the simultaneous variations of canonical variables.A counter example to a conjecture of the Dirac for a system with a singular high-order Lagrangian is given,in which there is no linearization of constraint.展开更多
The spark plasma sintering (SPS) technique was introduced into the field ofNdFeB preparation due to its own advantages. High property NdFeB magnets with fine grains wereprepared by SPS method. The corrosion behaviors ...The spark plasma sintering (SPS) technique was introduced into the field ofNdFeB preparation due to its own advantages. High property NdFeB magnets with fine grains wereprepared by SPS method. The corrosion behaviors of SPS NdFeB were studied by electrochemicalmeasurements and 92 percent RH hyther tests at 353 K. The results were compared with those of thetraditional sintered NdFeB magnets. It shows that both the SPS NdFeB and the traditional sinteredNdFeB have good corrosion resistance in alkaline environment due to surface passivation; while, thefine grain microstructure of SPS NdFeB results in a more homogeneous phase composition distributionand thus reduces the electrochemical inhomogenity between the ferromagnetic phase and the Nd-richinter-granular phase in the magnet. Therefore, the SPS NdFeB exhibits better corrosion resistancethan the traditional sintered NdFeB in neutral and weak acidic environment.展开更多
By means of FEM, the physiologi cal blood flow in coronary bypass graft is simula ted. The stenosis in coronary artery is involved in the graft model, and the def ormation of graft end to allow the surgical suture wit...By means of FEM, the physiologi cal blood flow in coronary bypass graft is simula ted. The stenosis in coronary artery is involved in the graft model, and the def ormation of graft end to allow the surgical suture with a smaller diameter coron ary is taken into consideration. The flow pattern, secondary flow and wall shear stress in the vicinity of anastomosis are analyzed. It is shown that a zone of low wall stress and high wall stress gradient exists downstream the toe. The flo or opposed to the anastomosis is an area of high wall stress and high wall stres s gradient. Both the toe downstream and the anastomosis bottom floor are prone t o intimal hyperplasia.展开更多
The purpose of this paper is to summarize the important studies in the area of impingement heat transfer with or without phase change, with emphasis on the research conducted at Beijing Polytechnic University mainly w...The purpose of this paper is to summarize the important studies in the area of impingement heat transfer with or without phase change, with emphasis on the research conducted at Beijing Polytechnic University mainly with circular jets. Heat transfer characteristics of single phase jets are discussed in detail. Comment is presented on boiling heat transfer of impinging jets for steady and transient states. Some special colling configurations of two-phase jets are also introduced.展开更多
Using seven working fluids, a systematic experimental study was performed to investigate the local convective heat transfer from vertical heaters to impinging circular submerged jets in the range of Reynolds number be...Using seven working fluids, a systematic experimental study was performed to investigate the local convective heat transfer from vertical heaters to impinging circular submerged jets in the range of Reynolds number between 1.17 ×102 and 3.69 × 104 with the emphasis placed on the examination of Prandtl number dependence. Heat transfer coefficiellts at the stagnation point were collected and correlated with the plate held within and beyond the potential core. Radial distribution of the local heat transfer coefficient was measured with five test liquids. Based on the measured profiles of the local heat transfer, a correlation was developed to cover the entire range of the radial distance. Besides the presellt data, the correlations developed in this work were also compared with a large quantity of available data of circular air jets. General agreement was observed between the air data and the correlat ions.展开更多
An analytical research was conducted to study heat transfer from horizontal surfaces to normally impinging circular jets under arbitrary-heat-flux conditions. The laminar thermal and hydraulic boundary layers were div...An analytical research was conducted to study heat transfer from horizontal surfaces to normally impinging circular jets under arbitrary-heat-flux conditions. The laminar thermal and hydraulic boundary layers were divided into five regions of flow. General expressions of heat transfer coefficients were obtained in all the four regions of stagnation and wall jet zones before the hydraulic jump.展开更多
文摘A novel treating technology for nitrogen removal from soybean wastewater was studied. The process for nitrogen removal was achieved by alternating aeration and mixing, combined with real\|time control strategies. Results showed that the COD and total nitrogen removal rates are more than 90% and 92% at COD and total nitrogen loads of 1\^0-1\^2 kg COD/(kgMLSS·d) and 0\^20-0\^27 kg TN/(kgMLSS·d), respectively. In addition, it could improve sludge settling property. SVI value is less than 70 g/ml during the whole cycles. The method not only may be adapted to treat soybean wastewater with high nitrogen, but also may be applied to treat other high nitrogen wastewater.
基金The National Hi Tech Development Program (863) of China(No.2003AA601110) and the National Natural Science Foundation Key Item of China(No.50138010)
文摘Control of sludge age and mixed liquid suspended solids concentration in the activated sludge process is critical for ensuring effective wastewater treatment. A nonlinear dynamic model for a step-feed activated sludge process was developed in this study. The system is based on the control of the sludge age and mixed liquor suspended solids in the aerator of last stage by adjusting the sludge recycle and wastage flow rates respectively. The simulation results showed that the sludge age remained nearly constant at a value of 16 d in the variation of the influent characteristics. The mixed liquor suspended solids in the aerator of last stage were also maintained to a desired value of 2500 g/m3 by adjusting wastage flow rates.
文摘In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical probes and an EKTAPRO 1000 high speed motion analyzer. It demonstrates that the radial profile of slug flow void fraction is parabolic. Influenced by the falling liquid film, the radial profile curve of liquid slug void fraction in the wake region is also parabolic. Since fully turbulent velocity distribution is built up in the developed region,the void fraction profile in this region is the saddle type. At given superficial liquid velocity, the liquid slug void fraction increases with gas velocity. The radial profiles of liquid slug void fraction at different axial locations are all saddle curves, but void fraction is obviously high around the centerline in the entrance region. The nearer the measuring station is from the entrance, the farther the peak location is away from the wall.
基金Karen Elise Jensens Foundation and the Danish Technical Research Council
文摘AIM:Systemic treatment with epidermal growth factor (EGF)leads to growth of all parts of the small intestine in normal functioning rats. In this study, we investigated the effect of this growth process on morphometric and biomechanical parameters of ileum.METHODS: Rats were treated with EGF (150 μg@kg-1day-1)or placebo via osmotic minipumps for 2, 4, 7, and 14 days.A segment of ileum was removed. The morphology at noload state and zero-stress state was measured and passive biomechanical properties were assessed using a biaxial test machine (combined inflation and axial stretching).RESULTS: The ileum weight increased after EGF administration. After 4 days' EGF treatment, the wall thickness was increased. Significantly smaller inner perimeters were seen in 4 day and 7 day EGF treatment groups. The opening angle and residual strain began to increase after 7 days' EGF treatment. Wall stiffness, evaluated from the stress-strain curves, showed a continuous decrease in circumferential direction during the first 7 days' EGF treatment. The longitudinal stiffness increased during the first 7 days. The stress-strain curves for both circumferential and longitudinal direction tended to shift back to normal 14days after starting EGF administration.CONCLUSION: EGF can cause significant changes both in the morphology and in the passive mechanical properties of the rat ileum.
基金the National Natural Science Foundation of China(No.2 0 0 4 2 0 0 1) and by the Postdoctoral Foundation ofthe Ministry of Education P.R.China
文摘Semi-empirical molecular orbital calculations were performed on heterocyclic aromatic amines(HCAs). The relationship between the structures and the carcinogenicities can be rationally elucidated by the models based on the metabolism of HCAs and the Di-region theory. The degree of easiness for the formation of Di-region electrophilic centers determines the carcinogenic activity. There is a good linear relationship between the observed carcinogenicities and the PM3 calculated parameters, with r=0.973 and F=29.8>F ** 0.01 .
文摘Based on generalized Apell-Chetaev constraint conditions and to take the inherent constrains for singular Lagrangian into account,the generalized canonical equations for a general mechanical system with a singular higher-order Lagrangian and subsidiary constrains are formulated. The canonical symmetries in phase space for such a system are studied and Noether theorem and its inversion theorem in the generalized canonical formalism have been established.
文摘AIM: To propose a simple and effective method suitable for analyzing the angle and distribution of 2-dimensional collagen fiber in larger sample of small intestine and to investigate the relationship between the angles of collagen fiber and the pressure it undergoes.METHODS: A kind of 2-dimensional visible quantitative analyzing technique was described. Digital image-processing method was utilized to determine the angle of collagen fiber in parenchyma according to the changes of area analyzed and further to investigate quantitatively the distribution of collagen fiber. A series of intestinal slice′s images preprocessed by polarized light were obtained with electron microscope,and they were processed to unify each pixel. The approximate angles between collagen fibers were obtained via analyzing the images and their corresponding polarized light. The relationship between the angles of collagen fiber and the pressure it undergoes were statistically summarized.RESULTS: The angle of collagen fiber in intestinal tissue was obtained with the quantitative analyzing method of calculating the ratio of different pixels. For the same slice,with polarized light angle′s variation, the corresponding ratio of different pixels was also changed; for slices under different pressures, the biggest ratio of collagen fiber area was changed either.CONCLUSION: This study suggests that the application of stress on the intestinal tissue will change the angle and content of collagen fiber. The method of calculating ratios of different pixel values to estimate collagen fiber angle was practical and reliable. The quantitative analysis used in the present study allows a larger area of soft tissue to be analyzed with relatively low cost and simple equipment.
文摘In the present research Monte Carlo technique was used to simulate the grain growth in heat-affected zone(HAZ) of an ultrafine grain steel. An experimental data based (EBD) model proposed by Gao was used to establish the relation between tMCS and real time temperature kinetics in our simulation. The simulations give out the evolution of grain structure and grain size distribution in HAZ of the ultrafine grain steel. A Microsoft Window based on computer program for the simulation of grain growth in the HAZ of weldment in three dimensions has been developed using Monte Carlo technique. For the system, inputting the temperature field data and material properties, the evolution of grain structure, both image of simulated grain structure and numerical datum reflecting grain size distribution can be produced by the program. The system was applied to the ultrafine grain steel welding, and the simulated results show that the ultrafine grain steel has large tendency of grain growth.
文摘A new genetic algorithm (GA) is developed. It features three new operations: restoration, reconstruction and recording the better, so as to produce a limited monotonic sequence of fitness value, to realize a globally optimal choosing, and to converge to a globally optimal solution through a perfectly stochastic process. Practical examples are given to illustrate the superiority of this new GA.
文摘The effect of seawater salinity on nitrite accumulation in short-range nitrification to nitrite as the end product was studied by using a SBR. Experimental results indicated that the growth of nitrobacteria was inhibited and very high levels of nitrite accumulation at different salinities were achieved under the conditions of 25—28℃, pH 7.5? ?.0 , and the influent ammonia nitrogen of 40—70 mg/L when seawater flow used to flush toilet was less than 35%(salinity 12393 mg/L, Cl - 6778 mg/L) of total domestic wastewater flow, which is mainly ascribed to much high chlorine concentration of seawater. Results showed that high seawater salinity is available for short-range nitrification to nitrite as the end product. When the seawater flow used to flush toilet accounting for above 70% of the total domestic wastewater flow, the removal efficiency of ammonia was still above 80% despite the removal of organics declined obviously(less than 60%). It was found that the effect of seawater salinity on the removal of organics was negative rather than positive one as shown for ammonia removal.
基金National Natural Science Foundation of China(No.59501011)Science and Technology New Star Project of Beijing.
文摘Welded joint is a mechanical heterogeneous body, and mechanical heterogeneity has great effect on dynamic fracture behaviour of welded joints. In the present investigation, dynamic response curve and dynamic J-integral of practical undermatched welded joint and whole base and whole weld three-point-bend (TPB) models containing longitudinal crack are com- puted. Dynamic J-integral is evaluated using virtual crack extension (VCE) method and the computation is performed using MARC finite element code. Because of the effect of inertia, dynamic load response curve of computed model waves periodically. Dynamic J-integral evaluated by VCE method is path independent. The effect of inertia has little influence on dynamic J-integral curve. The value of dynamic J-integral of undermatched welded joint is lower than that of whole base metal and higher than that of whole weld metal. The results establish the foundation of safety evaluation for dynamic loaded welded structures.
文摘Based on the canonical action,a generalized canonical first Noether theorem and Poicare-Cartan integralinvariant for a system with a singular high-order Lagrangian are derived.It is worth while to point out that the constraints are invariant under the total variation of canonical variables including time.We can also deduce the result,which differs from the previous work to reuire that the constraints are invariant under the simultaneous variations of canonical variables.A counter example to a conjecture of the Dirac for a system with a singular high-order Lagrangian is given,in which there is no linearization of constraint.
文摘The spark plasma sintering (SPS) technique was introduced into the field ofNdFeB preparation due to its own advantages. High property NdFeB magnets with fine grains wereprepared by SPS method. The corrosion behaviors of SPS NdFeB were studied by electrochemicalmeasurements and 92 percent RH hyther tests at 353 K. The results were compared with those of thetraditional sintered NdFeB magnets. It shows that both the SPS NdFeB and the traditional sinteredNdFeB have good corrosion resistance in alkaline environment due to surface passivation; while, thefine grain microstructure of SPS NdFeB results in a more homogeneous phase composition distributionand thus reduces the electrochemical inhomogenity between the ferromagnetic phase and the Nd-richinter-granular phase in the magnet. Therefore, the SPS NdFeB exhibits better corrosion resistancethan the traditional sintered NdFeB in neutral and weak acidic environment.
文摘By means of FEM, the physiologi cal blood flow in coronary bypass graft is simula ted. The stenosis in coronary artery is involved in the graft model, and the def ormation of graft end to allow the surgical suture with a smaller diameter coron ary is taken into consideration. The flow pattern, secondary flow and wall shear stress in the vicinity of anastomosis are analyzed. It is shown that a zone of low wall stress and high wall stress gradient exists downstream the toe. The flo or opposed to the anastomosis is an area of high wall stress and high wall stres s gradient. Both the toe downstream and the anastomosis bottom floor are prone t o intimal hyperplasia.
文摘The purpose of this paper is to summarize the important studies in the area of impingement heat transfer with or without phase change, with emphasis on the research conducted at Beijing Polytechnic University mainly with circular jets. Heat transfer characteristics of single phase jets are discussed in detail. Comment is presented on boiling heat transfer of impinging jets for steady and transient states. Some special colling configurations of two-phase jets are also introduced.
文摘Using seven working fluids, a systematic experimental study was performed to investigate the local convective heat transfer from vertical heaters to impinging circular submerged jets in the range of Reynolds number between 1.17 ×102 and 3.69 × 104 with the emphasis placed on the examination of Prandtl number dependence. Heat transfer coefficiellts at the stagnation point were collected and correlated with the plate held within and beyond the potential core. Radial distribution of the local heat transfer coefficient was measured with five test liquids. Based on the measured profiles of the local heat transfer, a correlation was developed to cover the entire range of the radial distance. Besides the presellt data, the correlations developed in this work were also compared with a large quantity of available data of circular air jets. General agreement was observed between the air data and the correlat ions.
文摘An analytical research was conducted to study heat transfer from horizontal surfaces to normally impinging circular jets under arbitrary-heat-flux conditions. The laminar thermal and hydraulic boundary layers were divided into five regions of flow. General expressions of heat transfer coefficients were obtained in all the four regions of stagnation and wall jet zones before the hydraulic jump.
