For the numerical simulation of flow systems with various complex components, the traditional one-dimensional （1D） network method has its comparative advantage in time consuming and the CFD method has its absolute a...For the numerical simulation of flow systems with various complex components, the traditional one-dimensional （1D） network method has its comparative advantage in time consuming and the CFD method has its absolute advantage in the detailed flow capturing. The proper coupling of the advantages of different dimensional methods can strike balance well between time cost and accuracy and then significantly decrease the whole design cycle for the flow systems in modern machines. A novel multi-fidelity coupled simulation method with numerical zooming is developed for flow systems. This method focuses on the integration of one-, two-and three-dimensional codes for various components. Coupled iterative process for the different dimensional simulation cycles of sub-systems is performed until the concerned flow variables of the whole system achieve convergence. Numerical zooming is employed to update boundary data of components with different dimen-sionalities. Based on this method, a highly automatic, multi-discipline computing environment with integrated zooming is developed. The numerical results of Y-Junction and the air system of a jet engine are presented to verify the solution method. They indicate that this type of multi-fidelity simulationmethod can greatly improve the prediction capability for the flow systems.展开更多
Effects of unsteady deformation of a＇flapping model insect wing on its aerodynamic force production are studied by solving the Navier-Stokes equations on a dynamically deforming grid. Aerodynamic forces on the flappi...Effects of unsteady deformation of a＇flapping model insect wing on its aerodynamic force production are studied by solving the Navier-Stokes equations on a dynamically deforming grid. Aerodynamic forces on the flapping wing are not much affected by considerable twist, but affected by camber deformation. The effect of combined camber and twist deformation is similar to that of camber deformation. With a deformation of 6% camber and 20% twist （typical values observed for wings of many insects）, lift is increased by 10% - 20% and lift-to-drag ratio by around 10% compared with the case of a rigid fiat-plate wing. As a result, the deformation can increase the maximum lift coefficient of an insect, and reduce its power requirement for flight. For example, for a hovering bumblebee with dynamically deforming wings （6% camber and 20% twist）, aerodynamic power required is reduced by about 16% compared with the case of rigid wings.展开更多
This study is aimed at using blade 3-D optimization to control corner flows in the high through-flow fan/booster of a high bypass ratio commercial turbofan engine. Two kinds of blade 3-D optimization, end-bending and ...This study is aimed at using blade 3-D optimization to control corner flows in the high through-flow fan/booster of a high bypass ratio commercial turbofan engine. Two kinds of blade 3-D optimization, end-bending and bow, are focused on. On account of the respective operation mode and environment, the approach to 3-D aerodynamic modeling of rotor blades is different from stator vanes. Based on the understanding of the mechanism of the corner flow and the consideration of intensity problem for rotors, this paper uses a variety of blade 3-D optimization approaches, such as loading distribution optimization, perturbation of departure angles and stacking-axis manipulation, which are suitable for rotors and stators respectively. The obtained 3-D blades and vanes can improve the corner flow features by end-bending and bow effects. The results of this study show that flows in corners of the fan/booster, such as the fan hub region, the tip and hub of the vanes of the booster, are very complex and dominated by 3-D effects. The secondary flows there are found to have a strong detrimental effect on the compressor performance. The effects of both end-bending and bow can improve the flow separation in corners, but the specific ways they work and application scope are somewhat different. Redesigning the blades via blade 3-D optimization to control the corner flow has effectively reduced the loss generation and improved the stall margin by a large amount.展开更多
A throughflow model based on the time-marching finite volume approach is described in this paper. The governing equations are derived by circumferentially averaging the three-dimensional Navier-Stokes equations neglec...A throughflow model based on the time-marching finite volume approach is described in this paper. The governing equations are derived by circumferentially averaging the three-dimensional Navier-Stokes equations neglecting the circumferentially non-uniform and viscous terms. An inviscid blade force model similar to the Large-particle method is derived. The viscous blade force has been modeled by the distributed loss model. The convective fluxes of the governing equation are discretized with the Edward’s low-diffusion flux-splitting (LDFSS) scheme. And a point-iterative Symmetric Gauss-Seidel (SGS) scheme is used in the temporal discretization. The throughflow model has been applied to the NASA Rotor 67 and a high-load transonic fan stage ATS-2. The reasonable good agreements with the experiments and the 3D viscous computations show the potential of the method.展开更多
The governing equations are derived by circumferentially averaging the three-dimensional （3D） Navier-Stokes equations, which are solved using a time marching finite volume approach. Both Euler throughflow model and ...The governing equations are derived by circumferentially averaging the three-dimensional （3D） Navier-Stokes equations, which are solved using a time marching finite volume approach. Both Euler throughflow model and Navier-Stokes （N-S） throughflow model are employed to investigate the performance and flow fields of a highly loaded transonic single-stage fan ATS-2 and a four-stage fan. The results are compared with the experimental and three-dimensional computational results. It shows that the throughflow models can provide reasonable perform- ance characteristics and N-S throughflow model gives better predictions in endwall regions. A throughflow com- putation in which all the non-axisymmetric terms are included has been performed at off-design condition and the radial distributions of the flow field can be well described.展开更多
The assembling error may lead to variation in stagger angles,which would affect the aerodynamic performance of the turbine.To investigate this underlying effect,two parallel numerical experiments on two turbines with ...The assembling error may lead to variation in stagger angles,which would affect the aerodynamic performance of the turbine.To investigate this underlying effect,two parallel numerical experiments on two turbines with the same profile,but uniform and nonuniform vane stagger angle respectively,were conducted in both steady and unsteady methods.The results indicate that certain changes in the detailed flow field of the turbine occur when the stagger angles are nonuniform,further,the blade loading distribution of the vane and rotor become markedly different from that in uniform vane stagger angle situation.Then these consequences caused by nonuniformity mentioned above enhance the unsteadiness of the flow,finally,the aerodynamic performance changes dramatically.It also shows that,compared with steady simulation,the unsteady numerical simulation is necessary in this investigation.展开更多
基金National Weapon Equipment Pre-research Foundation of China(0C410101110C4101)Innovation Foundation of BUAA for PhD Graduates(YWF-13-A01-15)for funding this work
文摘For the numerical simulation of flow systems with various complex components, the traditional one-dimensional （1D） network method has its comparative advantage in time consuming and the CFD method has its absolute advantage in the detailed flow capturing. The proper coupling of the advantages of different dimensional methods can strike balance well between time cost and accuracy and then significantly decrease the whole design cycle for the flow systems in modern machines. A novel multi-fidelity coupled simulation method with numerical zooming is developed for flow systems. This method focuses on the integration of one-, two-and three-dimensional codes for various components. Coupled iterative process for the different dimensional simulation cycles of sub-systems is performed until the concerned flow variables of the whole system achieve convergence. Numerical zooming is employed to update boundary data of components with different dimen-sionalities. Based on this method, a highly automatic, multi-discipline computing environment with integrated zooming is developed. The numerical results of Y-Junction and the air system of a jet engine are presented to verify the solution method. They indicate that this type of multi-fidelity simulationmethod can greatly improve the prediction capability for the flow systems.
基金Project supported by the"Fan Zhou"Youth Science Fund of Beijing University of Aeronautics and Astronautics (No.20070404)
文摘Effects of unsteady deformation of a＇flapping model insect wing on its aerodynamic force production are studied by solving the Navier-Stokes equations on a dynamically deforming grid. Aerodynamic forces on the flapping wing are not much affected by considerable twist, but affected by camber deformation. The effect of combined camber and twist deformation is similar to that of camber deformation. With a deformation of 6% camber and 20% twist （typical values observed for wings of many insects）, lift is increased by 10% - 20% and lift-to-drag ratio by around 10% compared with the case of a rigid fiat-plate wing. As a result, the deformation can increase the maximum lift coefficient of an insect, and reduce its power requirement for flight. For example, for a hovering bumblebee with dynamically deforming wings （6% camber and 20% twist）, aerodynamic power required is reduced by about 16% compared with the case of rigid wings.
基金supported by National Natural Science Foundation of China(51006005,51236001)National Basic Research Program of China(2012CB720201)Beijing Natural Science Foundation(No.3151002)
基金supported by National Natural Science Foundation of China (51006005,50736007)"Fan-Zhou" Youth Foundation(20100401)
文摘This study is aimed at using blade 3-D optimization to control corner flows in the high through-flow fan/booster of a high bypass ratio commercial turbofan engine. Two kinds of blade 3-D optimization, end-bending and bow, are focused on. On account of the respective operation mode and environment, the approach to 3-D aerodynamic modeling of rotor blades is different from stator vanes. Based on the understanding of the mechanism of the corner flow and the consideration of intensity problem for rotors, this paper uses a variety of blade 3-D optimization approaches, such as loading distribution optimization, perturbation of departure angles and stacking-axis manipulation, which are suitable for rotors and stators respectively. The obtained 3-D blades and vanes can improve the corner flow features by end-bending and bow effects. The results of this study show that flows in corners of the fan/booster, such as the fan hub region, the tip and hub of the vanes of the booster, are very complex and dominated by 3-D effects. The secondary flows there are found to have a strong detrimental effect on the compressor performance. The effects of both end-bending and bow can improve the flow separation in corners, but the specific ways they work and application scope are somewhat different. Redesigning the blades via blade 3-D optimization to control the corner flow has effectively reduced the loss generation and improved the stall margin by a large amount.
基金supported by National Natural Science Foundation of China (50676004, 50736007)"Fan-Zhou" Youth Foundation (20100401)the Fun-damental Research Funds for the Central Universities (YWF-10-02-013)
文摘A throughflow model based on the time-marching finite volume approach is described in this paper. The governing equations are derived by circumferentially averaging the three-dimensional Navier-Stokes equations neglecting the circumferentially non-uniform and viscous terms. An inviscid blade force model similar to the Large-particle method is derived. The viscous blade force has been modeled by the distributed loss model. The convective fluxes of the governing equation are discretized with the Edward’s low-diffusion flux-splitting (LDFSS) scheme. And a point-iterative Symmetric Gauss-Seidel (SGS) scheme is used in the temporal discretization. The throughflow model has been applied to the NASA Rotor 67 and a high-load transonic fan stage ATS-2. The reasonable good agreements with the experiments and the 3D viscous computations show the potential of the method.
基金supported by National Natural Science Foundation of China (50736007, 51006005)
文摘The governing equations are derived by circumferentially averaging the three-dimensional （3D） Navier-Stokes equations, which are solved using a time marching finite volume approach. Both Euler throughflow model and Navier-Stokes （N-S） throughflow model are employed to investigate the performance and flow fields of a highly loaded transonic single-stage fan ATS-2 and a four-stage fan. The results are compared with the experimental and three-dimensional computational results. It shows that the throughflow models can provide reasonable perform- ance characteristics and N-S throughflow model gives better predictions in endwall regions. A throughflow com- putation in which all the non-axisymmetric terms are included has been performed at off-design condition and the radial distributions of the flow field can be well described.
基金supported by National Nature Science Foundation of China under Grant Number 50776003the Innovation Foundation of BUAA for PhD Graduates
文摘The assembling error may lead to variation in stagger angles,which would affect the aerodynamic performance of the turbine.To investigate this underlying effect,two parallel numerical experiments on two turbines with the same profile,but uniform and nonuniform vane stagger angle respectively,were conducted in both steady and unsteady methods.The results indicate that certain changes in the detailed flow field of the turbine occur when the stagger angles are nonuniform,further,the blade loading distribution of the vane and rotor become markedly different from that in uniform vane stagger angle situation.Then these consequences caused by nonuniformity mentioned above enhance the unsteadiness of the flow,finally,the aerodynamic performance changes dramatically.It also shows that,compared with steady simulation,the unsteady numerical simulation is necessary in this investigation.
