Mechanical properties of Mg-3Gd(wt.%)samples with average grain sizes ranging from 3 to 45μm were characterized by room temperature tensile test.A reversal of the trade-off,i.e.,high yield strength and large tensile ...Mechanical properties of Mg-3Gd(wt.%)samples with average grain sizes ranging from 3 to 45μm were characterized by room temperature tensile test.A reversal of the trade-off,i.e.,high yield strength and large tensile elongation,was simultaneously observed in the fine-grained samples.The microstructures and hardening response were analyzed in terms of the viewpoint of strain evolution,including local strain evolution by tensile digital image correlation strain measurement,and lattice strain by using synchrotronbased in-situ high energy X-ray diffraction technique.The dislocation-based deformation mechanisms were investigated to underpin the microstructural origin of the yield point phenomenon and enhancement in work-hardening.The occurrence of the yield point phenomenon represented by a yield drop and propagation of the Lüders band is related to the absence of mobile dislocations at an early stage and to the slip transmission between the adjacent grain.The extraordinary work-hardening enhancement over an extended range can be ascribed mainly to the increases in dislocation multiplication and accumulation capabilities by the activation and interaction of multiple slip systems includingand<c+a>types.These results contribute to the design of strong and ductile Mg alloys.展开更多
The metastable austenite was transformed to martensite by prestrain tension of SUS304 stainless steel to study the influence of transformed martensite on its subsequent work-hardening behavior under the uniaxial tensi...The metastable austenite was transformed to martensite by prestrain tension of SUS304 stainless steel to study the influence of transformed martensite on its subsequent work-hardening behavior under the uniaxial tensile condition. The X-ray diffractometer （XRD） was employed to detect the transformed martensite. Results showed that the volume fraction of transformed martensite increases with increasing prestrain. The pre-transformed martensite in the microstructure remarkably affects the deformation behavior of the steel, and the strength increases and the elongation decreases. The work-hardening curve of prestrained specimens observably changes with true strain. The work-hardening exponent n of stainless steel decreases with the increase of pre-transformed martensite. The achievement is a significant contribution to the process design during pressing.展开更多
We analyze a large-scale molecular dynamics simulation of work hardening in a model system of a ductile solid. With tensile loading, we observe emission of thousands of dislocations from two sharp cracks. The dislocat...We analyze a large-scale molecular dynamics simulation of work hardening in a model system of a ductile solid. With tensile loading, we observe emission of thousands of dislocations from two sharp cracks. The dislocations interact in a complex way, revealing three fundamental mechanisms of work-hardening in this ductile material. These are (1) dislocation cutting processes, jog formation and generation of trails of point defects; (2) activation of secondary slip systems by Frank-Read and cross-slip mechanisms; and (3) formation of sessile dislocations such as Lomer-Cottrell locks. We report the discovery of a new class of point defects referred to as trail of partial point defects, which could play an important role in situations when partial dislocations dominate plasticity. Another important result of the present work is the rediscovery of the Fleischer-mechanism of cross-slip of partial dislocations that was theoretically proposed more than 50 years ago, and is now, for the first time, confirmed by atomistic simulation. On the typical time scale of molecular dynamics simulations, the dislocations self-organize into a complex sessile defect topology. Our analysis illustrates numerous mechanisms formerly only conjectured in textbooks and observed indirectly in experiments. It is the first time that such a rich set of fundamental phenomena have been revealed in a single computer simulation, and its dynamical evolution has been studied. The present study exemplifies the simulation and analysis of the complex nonlinear dynamics of a many-particle system during failure using ultra-large scale computing.展开更多
Three characteristic points in the deformation history of a fractured tensile specimen are selected tocalculate two values of n( n1 and n2 ) to represent the hardening ability of material during the homogeneous plas-t...Three characteristic points in the deformation history of a fractured tensile specimen are selected tocalculate two values of n( n1 and n2 ) to represent the hardening ability of material during the homogeneous plas-tic deformation and the following large plastic deformation. Experimental results obtained with mild streel andred copper show that n determined using the three-point method proposed is better to describe the hardening a-bility of material. It is therefore concluded that three-point method can be used to describe the hardening prop-erty of material during both homogeneous deformation and large plastic deformation.展开更多
The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile ...The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile metal and the dispersive phase is assumed to consist of either aligned or randomly-oriented, elastic,, spheroidal inhomogeneities. The plastic flow and decreasing stiffness of the matrix during Eshelby's transformation strain of the equivalent inclusions are accounted for by using the deformation theory of plasticity. The explicit results of the instantaneous overall thermal expansion coefficients and the critical inelastic temperature changes are presented for aligned disc- and fiber-inclusions. For the spherical and randomly-oriented spheroidal inclusion, the present study demonstrates that when the yielding of the composites is governed by the average matrix stress, the overall response is always elastic in spite of the temperature change.展开更多
The work-hardening behaviour in an Fe-Mn-Si-Cr-Ni alloy has been investigated using tensile test at different temperatures and TEM observation. It was found that besides the intersection of εmartensite, the intersect...The work-hardening behaviour in an Fe-Mn-Si-Cr-Ni alloy has been investigated using tensile test at different temperatures and TEM observation. It was found that besides the intersection of εmartensite, the intersections of ε martensite with stacking fault and the cross-slip of dislocation which is difficult to occur in the alloy with low stacking fault energy are also important factors to the temperature dependent work-hardening behaviour.展开更多
A new approach is proposed to characterize the work-hardening behavior of metals based on the stress-strain data from uniaxial extension testing.With this new approach,the yield strength as a function of the plastic w...A new approach is proposed to characterize the work-hardening behavior of metals based on the stress-strain data from uniaxial extension testing.With this new approach,the yield strength as a function of the plastic work can be determined by directly fitting a wellchosen single-variable shape function to any given uniaxial data from the initial yielding up to the strength limit,in an explicit sense with no need to carry out the usual tedious trial-and-error procedures in treating nonlinear elastoplastic rate equations toward identifying numerous unknown parameters.Numerical examples show that the simulation results with the new approach are in accurate agreement with the test data.展开更多
X-ray diffraction Fourier profile analysis has been performed for polycrystalline α-brass plate with 31.55 wt-% Zn after a series of uniaxial tensile tests with different strain rates. Dislocation density p and confi...X-ray diffraction Fourier profile analysis has been performed for polycrystalline α-brass plate with 31.55 wt-% Zn after a series of uniaxial tensile tests with different strain rates. Dislocation density p and configuration parameter M may be presented as a function of ap- plied stress σ_a.A mechanism of alternative long-range and short-range strain hardening has been proposed.展开更多
The effect of C,Mn and heat-treatment on work-hardening of austenitic Mn steel and the work-hardening mechanism have been investigated under non-severe impact loading condition.The results show that the ability of wor...The effect of C,Mn and heat-treatment on work-hardening of austenitic Mn steel and the work-hardening mechanism have been investigated under non-severe impact loading condition.The results show that the ability of work-hardening in- creases with the increase of C and aging tempera- ture but decreases with Mn.The work-hardening with high austenitic stability results mainly from dislocations,and that with low austenitic stability results mainly from combined effects of strain-in- duced martensite and high density of dislocations under non-severe impact loading conditions.The wear resistance of medium manganese steel (Mn7) is 1.64-2.46 times that of Hadfield steel (Mnl3).展开更多
Work-hardening behaviour of type 316 austenitic stainless steel having difFerent initial dislocation structures introduced by swaging to various levels is analysed by a simplified Kock's model which takes into acc...Work-hardening behaviour of type 316 austenitic stainless steel having difFerent initial dislocation structures introduced by swaging to various levels is analysed by a simplified Kock's model which takes into account the structural changes through the dislocation accumulation and annihilation process during deformation. The dislocation accumulation and annihilation factors show a temperature and structure dependence. The dislocation annihilation factor shows a plateau or decreasing tendency in the dynamic strain ageing (DSA) temperature range. This is attributed as either due to dislocation accumulation being more pronounced than dislocation annihilation or as due to precipitates being formed at DSA temperatures acting as obstacles to dislocation motion in the DSA temperature range.展开更多
Composition design is one of the signifcant methods to break the trade-of relation between strength and ductility of medium-/high-entropy alloys(M/HEAs).Herein,we introduced three fundamental principles for the compos...Composition design is one of the signifcant methods to break the trade-of relation between strength and ductility of medium-/high-entropy alloys(M/HEAs).Herein,we introduced three fundamental principles for the composition design:high elastic modulus,low stacking-fault energy(SFE),and appropriate phase stability.Subsequently,based on the three principles of component design and the frst-principles calculation results,we designed and investigated a non-equiatomic Ni28 MEA with a single-phase and uniform microstructure.The Ni28 MEA has great mechanical properties with yield strength of 329.5 MPa,tensile strength of 829.4 MPa,and uniform elongation of 56.9%at ambient temperature,respectively.The high ductility of Ni28 MEA may be attributed to the dynamically refned microstructure composed of hexagonal close-packed(HCP)lamellas and stacking faults(SFs),which provide extremely high work-hardening ability.This work demonstrates the feasibility of the three principles for composition design and can be extended to more M/HEAs in the future.展开更多
We discovered two distinctive features in the mechanical properties of extruded Mg alloys containing a long-period stacking ordered(LPSO)phase,which are highly desirable for a new class of high-strength,lightweight ma...We discovered two distinctive features in the mechanical properties of extruded Mg alloys containing a long-period stacking ordered(LPSO)phase,which are highly desirable for a new class of high-strength,lightweight materials.First,the Mg/LPSO-extruded alloy shows greater elongation compared to other Mg solid-solution-extruded alloys when a certain high strength is required.Second,the simultaneous achievement of high strength and large elongation in the Mg/LPSO-extruded alloy enhances with a reduction in extrusion speed.In this study,the physical origins of these features were examined,focusing on how changes in the microstructure affect the mechanical properties of the extruded alloys.Our findings clarify that the LPSO phase contributes not only to increased strength but also to enhanced elongation through an increase in the work-hardening rate,a mechanism we termed aanisotropic mechanical property-induced ductilizationo(AMID).Until now,most efforts to improve the ductility of Mg materials have focused on achieving aisotropic mechanical propertieso via grain refinement.Based on our results,we propose an entirely opposite approach:increasing the elongation of Mg alloy by locally enhancing theiraanisotropic mechanical propertieso through the AMID mechanism.Computational analysis further suggests that reducing the diameter of Mg-worked grains should effectively improving elongation in Mg/LPSO alloys with a high volume fraction of Mg-worked grains.展开更多
The development of low-cost,high-performance Mg alloys is crucial to the industrial applications of large-scale production of Mg alloys.In this work,extruded Mg-5Bi-3Al alloy with excellent mechanical properties is su...The development of low-cost,high-performance Mg alloys is crucial to the industrial applications of large-scale production of Mg alloys.In this work,extruded Mg-5Bi-3Al alloy with excellent mechanical properties is successfully prepared by modifying the extrusion temperatures(240℃and 300℃).The extruded alloy obtained ultra-high strength(yield strength=380 MPa,ultimate tensile strength=418 MPa)and excellent plasticity(elongation=10.2%)at the extrusion temperature of 240℃,the main contributing factors are primarily attributed to the synergistic effect of ultrafine recrystallized grain size(~0.5µm)and high density of Mg_(3)Bi_(2)precipitates.Stacking faults within the sub-micron Mg_(3)Bi_(2)phase are observed in the E240 alloy,confirming the plastic deformation capability of Mg_(3)Bi_(2)phase.The effects of extrusion temperature on the microstructure,mechanical properties,and work-hardening behavior of the extruded Mg-5Bi-3Al alloys at room temperature are systematically investigated.The results suggest that decreasing the extrusion temperature can refine recrystallized grain size and Mg_(3)Bi_(2)phase size,and the quantity of Mg_(3)Bi_(2)phase is increased,while increasing the extrusion temperature can improve the degree of recrystallization and weaken texture.The work hardening rate is increased with the increased extrusion temperature,mainly due to the coarsening of grains and precipitates,and the weakening of texture.This work provides an experimental basis for preparing high-performance wrought Mg-5Bi-3Al alloys.展开更多
The effect of Mo on dual-phase precipitation behavior and tensile properties of Fe26Mn8Al1.2C–(2–3.5 wt.%)Mo lightweight austenitic steels after annealing at 700℃was investigated by electron backscatter diffraction...The effect of Mo on dual-phase precipitation behavior and tensile properties of Fe26Mn8Al1.2C–(2–3.5 wt.%)Mo lightweight austenitic steels after annealing at 700℃was investigated by electron backscatter diffraction,transmission electron microscopy,hardness and tensile tests.Alloying with Mo in the steels promotes the precipitation of Mo_(2)C carbides while inhibits the precipitation ofκ-carbides.The addition of Mo exceeding 2.5 wt.%facilitates the precipitation of intragranular Mo_(2)C carbides,whereas with up to 2.5 wt.%Mo,only intergranular Mo_(2)C carbides precipitate.With containing more Mo in the steels,the strength increases due to enhancement of precipitation strengthening and solid solution strengthening,while ductility gradually decreases.3Mo steel exhibits excellent overall mechanical properties,with the synergistic increase in strength,ductility,and work-hardening rate,which can be attributed to the precipitation of fine intragranular Mo_(2)C distributed uniformly in the matrix and the suppression of the formation of coarsenedκ-carbides.However,in 3.5Mo steel,abundant coarsened Mo2C precipitation strongly interacts with dislocations to promote crack propagation along non-coherent interfaces,leading to a high initial work-hardening rate but severe ductility loss.展开更多
The influences of rolling reduction and aluminum sheet initial thickness(AIT)on the thickness fluctuation of aluminum layer(TFA)of embedded aluminum?steel composite sheet produced by cold roll bonding were investigate...The influences of rolling reduction and aluminum sheet initial thickness(AIT)on the thickness fluctuation of aluminum layer(TFA)of embedded aluminum?steel composite sheet produced by cold roll bonding were investigated,the formation mechanism of TFA was analyzed and method to improve the thickness uniformity of the aluminum layer was proposed.The results showed that when the reduction increased,TFA increased gradually.When the reduction was lower than40%,AIT had negligible effect on the TFA,while TFA increased with the decrease of AIT when the reduction was higher than40%.The non-uniformities of the steel surface deformation and the interfacial bonding extent caused by the work-hardened steel surface layer,were the main reasons for the formation of TFA.Adopting an appropriate surface treatment can help to decrease the hardening extent of the steel surface for improving the deformation uniformity during cold roll bonding process,which effectively improved the aluminum thickness uniformity of the embedded aluminum/steel composite sheets.展开更多
The restoration mechanisms for static recrystallization of work-hardened austenite were investigated by using double-pass compression tests performed on medium-carbon steel containing chromium and molybdenum. The soft...The restoration mechanisms for static recrystallization of work-hardened austenite were investigated by using double-pass compression tests performed on medium-carbon steel containing chromium and molybdenum. The softening fraction was defined by 2% offset method. The results show that Avrami exponent of about 0.21 is insensitive to deformation temperature, indicating that the action of steel grade should be considered. The time of 50% recrystallization (t0.5) decreases noteworthily with the increase of deformation temperature. Apparent activation energy for static recrystallization of 195 kJ/mol, which is close to that of vanadium microalloyed steel, is obtained by calculating. The increasing trend of the driving force for recrystallization is opposite to that of the deformation temperature, which is attributed to the number of operative slip system increasing as temperature increasing.展开更多
This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl...This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.展开更多
The cavitation erosion corrosion behaviour of ZQMn12-8-3-2 manganese-nickel-aluminum bronze and ZHMn55- 3-1 manganese-brass was investigated by mass loss, electrochemical measurements （polarization curves and electro...The cavitation erosion corrosion behaviour of ZQMn12-8-3-2 manganese-nickel-aluminum bronze and ZHMn55- 3-1 manganese-brass was investigated by mass loss, electrochemical measurements （polarization curves and electrochemical impedance spectroscopy） and the cavitation damaged surfaces were observed by scanning electron microscopy （SEM）. The results showed that ZQMn12-8-3-2 had better cavitation erosion resistance than ZHMn55-3-1. After the cavitation erosion for 6 h, the cumulative mass loss of ZQMn12-8-3-2 was about 1/3 that of ZHMn55-3-1. The corrosion current density of ZQMn12-8-3-2 was less than that of ZHMn55-3-1 under both static and cavitaiton condition. The free-corrosion potentials of ZQMn12-8-3-2 and ZHMn55-3-1 were all shifted in positive direction under cavitation condition compared to static condition. In the total cumulative mass loss under cavitation condition, the pure erosion played a key role for the two tested materials （74% for ZHMn55-3-1 and 60% for ZQMn12-8-3-2）, and the total synergism between corrosion and erosion of ZQMn12-8-3-2 （39%） was larger than that of ZHMn55-3-1 （23%）. The high cavitation erosion resistance of ZQMn12-8-3-2 was mainly attributed to its lower stacking fault energy （SFE）, the higher microhardness and work-hardening ability as well as the favorable propagation of cavitation cracks for ZQMn12-8-3-2, i.e., parallel to the surface rather than perpendicular to the surface for ZHMn55-3-1.展开更多
The tensile and fracture behaviors of AA6061 alloy were investigated in order to provide quantitative data about this alloy at cryogenic temperatures.Specimens of AA6061 alloy were solution heat treated before tensile...The tensile and fracture behaviors of AA6061 alloy were investigated in order to provide quantitative data about this alloy at cryogenic temperatures.Specimens of AA6061 alloy were solution heat treated before tensile tests at 298,173 and 77 K and tested at strain rates in the range from 0.1 to 0.0001 s^(−1).The results indicate the suppression of the Portevin−Le Chatelier(PLC)effect and dynamic strain aging(DSA)at 77 K.In contrast,at 298 K,a remarkable serrated flow,characteristic of the PLC effect,is observed.Furthermore,the tensile behavior at 77 K,compared with that observed at 173 and 298 K,shows a simultaneous increase in strength,uniform elongation,modulus of toughness,strain-hardening exponent and strain rate sensitivity,which is related to a decrease in the dynamic recovery rate at low temperature.These responses are reflected on the fracture morphology,since the dimple size decreases at 77 K,while the area covered by dimples increases.Comparisons of the Johnson−Cook model show that a good agreement can be obtained for tests at 173 and 77 K,in which DSA is suppressed.展开更多
基金financially supported by the National Key Research and Develop-ment Program(No.2023YFB3712702)the National Natural Science Foundation of China(Nos.52071038,52071039,and 52301156)the Natural Science Foundation of Jiangsu Province(Nos.BK20232025 and BK20243005)。
文摘Mechanical properties of Mg-3Gd(wt.%)samples with average grain sizes ranging from 3 to 45μm were characterized by room temperature tensile test.A reversal of the trade-off,i.e.,high yield strength and large tensile elongation,was simultaneously observed in the fine-grained samples.The microstructures and hardening response were analyzed in terms of the viewpoint of strain evolution,including local strain evolution by tensile digital image correlation strain measurement,and lattice strain by using synchrotronbased in-situ high energy X-ray diffraction technique.The dislocation-based deformation mechanisms were investigated to underpin the microstructural origin of the yield point phenomenon and enhancement in work-hardening.The occurrence of the yield point phenomenon represented by a yield drop and propagation of the Lüders band is related to the absence of mobile dislocations at an early stage and to the slip transmission between the adjacent grain.The extraordinary work-hardening enhancement over an extended range can be ascribed mainly to the increases in dislocation multiplication and accumulation capabilities by the activation and interaction of multiple slip systems includingand<c+a>types.These results contribute to the design of strong and ductile Mg alloys.
基金Item Sponsored by National Natural Science Foundation of China (50675128 50975166)
文摘The metastable austenite was transformed to martensite by prestrain tension of SUS304 stainless steel to study the influence of transformed martensite on its subsequent work-hardening behavior under the uniaxial tensile condition. The X-ray diffractometer （XRD） was employed to detect the transformed martensite. Results showed that the volume fraction of transformed martensite increases with increasing prestrain. The pre-transformed martensite in the microstructure remarkably affects the deformation behavior of the steel, and the strength increases and the elongation decreases. The work-hardening curve of prestrained specimens observably changes with true strain. The work-hardening exponent n of stainless steel decreases with the increase of pre-transformed martensite. The achievement is a significant contribution to the process design during pressing.
文摘We analyze a large-scale molecular dynamics simulation of work hardening in a model system of a ductile solid. With tensile loading, we observe emission of thousands of dislocations from two sharp cracks. The dislocations interact in a complex way, revealing three fundamental mechanisms of work-hardening in this ductile material. These are (1) dislocation cutting processes, jog formation and generation of trails of point defects; (2) activation of secondary slip systems by Frank-Read and cross-slip mechanisms; and (3) formation of sessile dislocations such as Lomer-Cottrell locks. We report the discovery of a new class of point defects referred to as trail of partial point defects, which could play an important role in situations when partial dislocations dominate plasticity. Another important result of the present work is the rediscovery of the Fleischer-mechanism of cross-slip of partial dislocations that was theoretically proposed more than 50 years ago, and is now, for the first time, confirmed by atomistic simulation. On the typical time scale of molecular dynamics simulations, the dislocations self-organize into a complex sessile defect topology. Our analysis illustrates numerous mechanisms formerly only conjectured in textbooks and observed indirectly in experiments. It is the first time that such a rich set of fundamental phenomena have been revealed in a single computer simulation, and its dynamical evolution has been studied. The present study exemplifies the simulation and analysis of the complex nonlinear dynamics of a many-particle system during failure using ultra-large scale computing.
文摘Three characteristic points in the deformation history of a fractured tensile specimen are selected tocalculate two values of n( n1 and n2 ) to represent the hardening ability of material during the homogeneous plas-tic deformation and the following large plastic deformation. Experimental results obtained with mild streel andred copper show that n determined using the three-point method proposed is better to describe the hardening a-bility of material. It is therefore concluded that three-point method can be used to describe the hardening prop-erty of material during both homogeneous deformation and large plastic deformation.
基金This work was supported by the National Science Foundation under the Grant 19302017 and 59472031
文摘The instantaneous thermal expansion behavior of-two-phase heterogeneous materials subjected to a uniform temperature change is explored in the present study. The matrix phase is assumed to be a work-hardening ductile metal and the dispersive phase is assumed to consist of either aligned or randomly-oriented, elastic,, spheroidal inhomogeneities. The plastic flow and decreasing stiffness of the matrix during Eshelby's transformation strain of the equivalent inclusions are accounted for by using the deformation theory of plasticity. The explicit results of the instantaneous overall thermal expansion coefficients and the critical inelastic temperature changes are presented for aligned disc- and fiber-inclusions. For the spherical and randomly-oriented spheroidal inclusion, the present study demonstrates that when the yielding of the composites is governed by the average matrix stress, the overall response is always elastic in spite of the temperature change.
文摘The work-hardening behaviour in an Fe-Mn-Si-Cr-Ni alloy has been investigated using tensile test at different temperatures and TEM observation. It was found that besides the intersection of εmartensite, the intersections of ε martensite with stacking fault and the cross-slip of dislocation which is difficult to occur in the alloy with low stacking fault energy are also important factors to the temperature dependent work-hardening behaviour.
基金This study was carried out under the support of the start-up fund from Jinan University(Guangzhou)the fund from the Natural Science Foundation of China(No.11372172).
文摘A new approach is proposed to characterize the work-hardening behavior of metals based on the stress-strain data from uniaxial extension testing.With this new approach,the yield strength as a function of the plastic work can be determined by directly fitting a wellchosen single-variable shape function to any given uniaxial data from the initial yielding up to the strength limit,in an explicit sense with no need to carry out the usual tedious trial-and-error procedures in treating nonlinear elastoplastic rate equations toward identifying numerous unknown parameters.Numerical examples show that the simulation results with the new approach are in accurate agreement with the test data.
文摘X-ray diffraction Fourier profile analysis has been performed for polycrystalline α-brass plate with 31.55 wt-% Zn after a series of uniaxial tensile tests with different strain rates. Dislocation density p and configuration parameter M may be presented as a function of ap- plied stress σ_a.A mechanism of alternative long-range and short-range strain hardening has been proposed.
文摘The effect of C,Mn and heat-treatment on work-hardening of austenitic Mn steel and the work-hardening mechanism have been investigated under non-severe impact loading condition.The results show that the ability of work-hardening in- creases with the increase of C and aging tempera- ture but decreases with Mn.The work-hardening with high austenitic stability results mainly from dislocations,and that with low austenitic stability results mainly from combined effects of strain-in- duced martensite and high density of dislocations under non-severe impact loading conditions.The wear resistance of medium manganese steel (Mn7) is 1.64-2.46 times that of Hadfield steel (Mnl3).
文摘Work-hardening behaviour of type 316 austenitic stainless steel having difFerent initial dislocation structures introduced by swaging to various levels is analysed by a simplified Kock's model which takes into account the structural changes through the dislocation accumulation and annihilation process during deformation. The dislocation accumulation and annihilation factors show a temperature and structure dependence. The dislocation annihilation factor shows a plateau or decreasing tendency in the dynamic strain ageing (DSA) temperature range. This is attributed as either due to dislocation accumulation being more pronounced than dislocation annihilation or as due to precipitates being formed at DSA temperatures acting as obstacles to dislocation motion in the DSA temperature range.
基金supported by the National Natural Science Foundation of China(Nos.52130002 and 52321001)the National Key Research and Development Program of China(No.2022YFB3708200)the Youth Innovation Promotion Association CAS(No.2018226).
文摘Composition design is one of the signifcant methods to break the trade-of relation between strength and ductility of medium-/high-entropy alloys(M/HEAs).Herein,we introduced three fundamental principles for the composition design:high elastic modulus,low stacking-fault energy(SFE),and appropriate phase stability.Subsequently,based on the three principles of component design and the frst-principles calculation results,we designed and investigated a non-equiatomic Ni28 MEA with a single-phase and uniform microstructure.The Ni28 MEA has great mechanical properties with yield strength of 329.5 MPa,tensile strength of 829.4 MPa,and uniform elongation of 56.9%at ambient temperature,respectively.The high ductility of Ni28 MEA may be attributed to the dynamically refned microstructure composed of hexagonal close-packed(HCP)lamellas and stacking faults(SFs),which provide extremely high work-hardening ability.This work demonstrates the feasibility of the three principles for composition design and can be extended to more M/HEAs in the future.
基金supported by the Japan Science and Technology Agency(JST),CREST(grant number JPMJCR2094)。
文摘We discovered two distinctive features in the mechanical properties of extruded Mg alloys containing a long-period stacking ordered(LPSO)phase,which are highly desirable for a new class of high-strength,lightweight materials.First,the Mg/LPSO-extruded alloy shows greater elongation compared to other Mg solid-solution-extruded alloys when a certain high strength is required.Second,the simultaneous achievement of high strength and large elongation in the Mg/LPSO-extruded alloy enhances with a reduction in extrusion speed.In this study,the physical origins of these features were examined,focusing on how changes in the microstructure affect the mechanical properties of the extruded alloys.Our findings clarify that the LPSO phase contributes not only to increased strength but also to enhanced elongation through an increase in the work-hardening rate,a mechanism we termed aanisotropic mechanical property-induced ductilizationo(AMID).Until now,most efforts to improve the ductility of Mg materials have focused on achieving aisotropic mechanical propertieso via grain refinement.Based on our results,we propose an entirely opposite approach:increasing the elongation of Mg alloy by locally enhancing theiraanisotropic mechanical propertieso through the AMID mechanism.Computational analysis further suggests that reducing the diameter of Mg-worked grains should effectively improving elongation in Mg/LPSO alloys with a high volume fraction of Mg-worked grains.
基金supported by the National Natural Science Foundation of China[grant nos.52371005,52022017,and 51927801]Fundamental Research Funds for the Central Universities.E.G.thanks Xiaomi Foundation for support.
文摘The development of low-cost,high-performance Mg alloys is crucial to the industrial applications of large-scale production of Mg alloys.In this work,extruded Mg-5Bi-3Al alloy with excellent mechanical properties is successfully prepared by modifying the extrusion temperatures(240℃and 300℃).The extruded alloy obtained ultra-high strength(yield strength=380 MPa,ultimate tensile strength=418 MPa)and excellent plasticity(elongation=10.2%)at the extrusion temperature of 240℃,the main contributing factors are primarily attributed to the synergistic effect of ultrafine recrystallized grain size(~0.5µm)and high density of Mg_(3)Bi_(2)precipitates.Stacking faults within the sub-micron Mg_(3)Bi_(2)phase are observed in the E240 alloy,confirming the plastic deformation capability of Mg_(3)Bi_(2)phase.The effects of extrusion temperature on the microstructure,mechanical properties,and work-hardening behavior of the extruded Mg-5Bi-3Al alloys at room temperature are systematically investigated.The results suggest that decreasing the extrusion temperature can refine recrystallized grain size and Mg_(3)Bi_(2)phase size,and the quantity of Mg_(3)Bi_(2)phase is increased,while increasing the extrusion temperature can improve the degree of recrystallization and weaken texture.The work hardening rate is increased with the increased extrusion temperature,mainly due to the coarsening of grains and precipitates,and the weakening of texture.This work provides an experimental basis for preparing high-performance wrought Mg-5Bi-3Al alloys.
基金supported by the funding of National Science and Technology Major Project,China(J2019-VI-0019-0134).
文摘The effect of Mo on dual-phase precipitation behavior and tensile properties of Fe26Mn8Al1.2C–(2–3.5 wt.%)Mo lightweight austenitic steels after annealing at 700℃was investigated by electron backscatter diffraction,transmission electron microscopy,hardness and tensile tests.Alloying with Mo in the steels promotes the precipitation of Mo_(2)C carbides while inhibits the precipitation ofκ-carbides.The addition of Mo exceeding 2.5 wt.%facilitates the precipitation of intragranular Mo_(2)C carbides,whereas with up to 2.5 wt.%Mo,only intergranular Mo_(2)C carbides precipitate.With containing more Mo in the steels,the strength increases due to enhancement of precipitation strengthening and solid solution strengthening,while ductility gradually decreases.3Mo steel exhibits excellent overall mechanical properties,with the synergistic increase in strength,ductility,and work-hardening rate,which can be attributed to the precipitation of fine intragranular Mo_(2)C distributed uniformly in the matrix and the suppression of the formation of coarsenedκ-carbides.However,in 3.5Mo steel,abundant coarsened Mo2C precipitation strongly interacts with dislocations to promote crack propagation along non-coherent interfaces,leading to a high initial work-hardening rate but severe ductility loss.
基金Project(2013AA031301)supported by National High-tech Research and Development Program of ChinaProject(51104016)supported by National Natural Science Foundation of ChinaProject(BM2014006)supported by Jiangsu Key Laboratory for Clad Materials,China
文摘The influences of rolling reduction and aluminum sheet initial thickness(AIT)on the thickness fluctuation of aluminum layer(TFA)of embedded aluminum?steel composite sheet produced by cold roll bonding were investigated,the formation mechanism of TFA was analyzed and method to improve the thickness uniformity of the aluminum layer was proposed.The results showed that when the reduction increased,TFA increased gradually.When the reduction was lower than40%,AIT had negligible effect on the TFA,while TFA increased with the decrease of AIT when the reduction was higher than40%.The non-uniformities of the steel surface deformation and the interfacial bonding extent caused by the work-hardened steel surface layer,were the main reasons for the formation of TFA.Adopting an appropriate surface treatment can help to decrease the hardening extent of the steel surface for improving the deformation uniformity during cold roll bonding process,which effectively improved the aluminum thickness uniformity of the embedded aluminum/steel composite sheets.
文摘The restoration mechanisms for static recrystallization of work-hardened austenite were investigated by using double-pass compression tests performed on medium-carbon steel containing chromium and molybdenum. The softening fraction was defined by 2% offset method. The results show that Avrami exponent of about 0.21 is insensitive to deformation temperature, indicating that the action of steel grade should be considered. The time of 50% recrystallization (t0.5) decreases noteworthily with the increase of deformation temperature. Apparent activation energy for static recrystallization of 195 kJ/mol, which is close to that of vanadium microalloyed steel, is obtained by calculating. The increasing trend of the driving force for recrystallization is opposite to that of the deformation temperature, which is attributed to the number of operative slip system increasing as temperature increasing.
基金Shahid Chamran University of Ahvaz for supporting this research
文摘This study has evaluated the effect of different levels of cold rolling（from 0 to 50%）on the microstructural,magnetic,and mechanical properties and the corrosion behavior of 316L austenitic stainless steel in Na Cl（1 mol/L）＋H_2SO_4（0.5 mol/L）solution.Microstructural examinations using optical microscopy revealed the development of a morphological texture from coaxial to elongated grains during the cold-rolling process.Phase analysis carried out on the basis of X-ray diffraction confirmed the formation of the ferromagneticα′-martensite phase under the stresses applied during cold rolling.This finding is in agreement with magnetic measurements using a vibrating sample magnetometer.Mechanical properties determined by tensile and Vickers microhardness tests demonstrated an upward trend in the hardness-to-yield strength ratio with increasing cold-rolling percentage,representing a reduction in the material’s work-hardening ability.Uniform and localized corrosion parameters were estimated via potentiodynamic polarization corrosion tests and electrochemical impedance spectroscopy.In contrast to the uniform corrosion,wherein the corrosion current density increased with increasing cold-working degree because of the high density of microstructural defects,the passive potential range and breakdown potential increased by cold working,showing greater resistance to pit nucleation.Although pits were formed,the cold-rolled material repassivation tendency decreased because of the broader hysteresis anodic loop,as confirmed experimentally by observation of the microscopic features after electrochemical cyclic polarization evaluations.
基金supported by the National Natural Science Foundation of China (No 50499336)
文摘The cavitation erosion corrosion behaviour of ZQMn12-8-3-2 manganese-nickel-aluminum bronze and ZHMn55- 3-1 manganese-brass was investigated by mass loss, electrochemical measurements （polarization curves and electrochemical impedance spectroscopy） and the cavitation damaged surfaces were observed by scanning electron microscopy （SEM）. The results showed that ZQMn12-8-3-2 had better cavitation erosion resistance than ZHMn55-3-1. After the cavitation erosion for 6 h, the cumulative mass loss of ZQMn12-8-3-2 was about 1/3 that of ZHMn55-3-1. The corrosion current density of ZQMn12-8-3-2 was less than that of ZHMn55-3-1 under both static and cavitaiton condition. The free-corrosion potentials of ZQMn12-8-3-2 and ZHMn55-3-1 were all shifted in positive direction under cavitation condition compared to static condition. In the total cumulative mass loss under cavitation condition, the pure erosion played a key role for the two tested materials （74% for ZHMn55-3-1 and 60% for ZQMn12-8-3-2）, and the total synergism between corrosion and erosion of ZQMn12-8-3-2 （39%） was larger than that of ZHMn55-3-1 （23%）. The high cavitation erosion resistance of ZQMn12-8-3-2 was mainly attributed to its lower stacking fault energy （SFE）, the higher microhardness and work-hardening ability as well as the favorable propagation of cavitation cracks for ZQMn12-8-3-2, i.e., parallel to the surface rather than perpendicular to the surface for ZHMn55-3-1.
基金We would like to acknowledge the Sao Paulo Research Foundation(FAPESP)(Grant No.2014/15091-7 and 2016/10997-0)the Conselho Nacional de Desenvolvimento Científico e Tecnológico-Brazil(CNPq)(Grant No.449009/2014-9)This study was financed in part by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior-Brazil(CAPES)-Finance Code 001.Danielle Cristina Camilo MAGALHÃES acknowledges CNPq for her PhD scholarship(Grant No.153181/2013-3).
文摘The tensile and fracture behaviors of AA6061 alloy were investigated in order to provide quantitative data about this alloy at cryogenic temperatures.Specimens of AA6061 alloy were solution heat treated before tensile tests at 298,173 and 77 K and tested at strain rates in the range from 0.1 to 0.0001 s^(−1).The results indicate the suppression of the Portevin−Le Chatelier(PLC)effect and dynamic strain aging(DSA)at 77 K.In contrast,at 298 K,a remarkable serrated flow,characteristic of the PLC effect,is observed.Furthermore,the tensile behavior at 77 K,compared with that observed at 173 and 298 K,shows a simultaneous increase in strength,uniform elongation,modulus of toughness,strain-hardening exponent and strain rate sensitivity,which is related to a decrease in the dynamic recovery rate at low temperature.These responses are reflected on the fracture morphology,since the dimple size decreases at 77 K,while the area covered by dimples increases.Comparisons of the Johnson−Cook model show that a good agreement can be obtained for tests at 173 and 77 K,in which DSA is suppressed.
