A wind tunnel test was conducted for a large steel gymnasium structure. Simultaneous pressure measurements were made on its entire ellipsoidal roof in a simulated suburban boundary layer flow field. Special attention ...A wind tunnel test was conducted for a large steel gymnasium structure. Simultaneous pressure measurements were made on its entire ellipsoidal roof in a simulated suburban boundary layer flow field. Special attention is paid to the charaeteristics of fluctuating wind pressures in different zones on the roof. Some selected results are presented： 1） correlations between fluctuating wind pressures on both roof surfaces, 2） eigenvalues and eigenvectors of covariance matrices of the fluctuating wind pressures, 3） probability distributions of the fluctuating wind pressures, and 4） statistical characteristics of peak factor. Furthermore, the applicability of the quasi-steady approach is discussed in detail. Based on the results, an empirical formula for estimating the minimum pressure coefficients, using a peak factor approach, is presented. Comparison of the minimum pressure coefficients determined by the proposed formula and those obtained from the wind tunnel tests is made to examine the applicability and accuracy of the proposed formula.展开更多
High-aspect-ratio aircraft are widely used in military and civilian fields,such as reconnaissance,surveillance,and attacks,due to their high lift-to-drag ratio,strong payload capability,significant endurance effect,an...High-aspect-ratio aircraft are widely used in military and civilian fields,such as reconnaissance,surveillance,and attacks,due to their high lift-to-drag ratio,strong payload capability,significant endurance effect,and good stealth performance.However,compared to conventional aircraft,high-aspect-ratio aircraft are more susceptible to gust disturbances during flight.In response to this phenomenon,a full-scale dynamic model of a high-aspect-ratio unmanned aerial vehicle was developed.Considering the coupling among control surfaces,structural forces,and aerodynamic forces,along with sensor,actuator,and delay effects,an H_(∞)control law was designed using the principle of singular value energy flow reduction and weighted function,with a PID(Proportional-Integral-Derivative)control law for comparison.The two controllers were then subjected to pulse-response and jury stability tests.Finally,wind tunnel tests were conducted to investigate the gust alleviation principle,in which gust disturbances were generated using gust generators and control surface self-excitation.The results present that the average wing root bending moment and wing tip overload under the PID control law decrease by approximately 30%,while under the H_(∞)control law,both the average wing root bending moment and wing tip overload reduction rate exceed 50%,with peaks reaching 60%.This validates the feasibility and efficiency of the designed H_(∞)controller.展开更多
The flutter characteristics of folding control fins with freeplay are investigated by numer- ical simulation and flutter wind tunnel tests. Based on the characteristics of the structures, fins with different freeplay ...The flutter characteristics of folding control fins with freeplay are investigated by numer- ical simulation and flutter wind tunnel tests. Based on the characteristics of the structures, fins with different freeplay angles are designed. For a 0° angle of attack, wind tunnel tests of these fins are conducted, and vibration is observed by accelerometers and a high-speed camera. By the expansion of the connected relationships, the governing equations of fit for the nonlinear aeroelastic analysis are established by the free-interface component mode synthesis method. Based on the results of the wind tunnel tests, the flutter characteristics of fins with different freeplay angles are analyzed. The results show that the vibration divergent speed is increased, and the divergent speed is higher than the flutter speed of the nominal linear system. The vibration divergent speed is increased along with an increase in the freeplay angle. The developed free-interface component mode synthesis method could be used to establish governing equations and to analyze the characteristics of nonlinear aeroe- lastic systems. The results of the numerical simulations and the wind tunnel tests indicate the same trends and critical velocities.展开更多
Combined with a UAV of the shape like Global Hawk, a new inlet is advanced to obtain high performance in both Radar Cross Section(RCS) and aerodynamic drag. Efforts are made to achieve this goal such as adopting a top...Combined with a UAV of the shape like Global Hawk, a new inlet is advanced to obtain high performance in both Radar Cross Section(RCS) and aerodynamic drag. Efforts are made to achieve this goal such as adopting a top-mounted inlet configuration, utilizing the diverterless technique and putting forward a new shape of entrance. A design method is brought forward and verified by wind tunnel tests. Results indicate: (1) Despite the negative effect of the front fuselage and the absence of the conventional boundary diverter, the performance of the top-mounted diverterless inlet advanced here(Ma:0.50-0.70, α:-4°-6°,σ>0.975) is equivalent to that of conventional S shaped inlet with diverter; (2) The integration of the inlet with the fuselage is realized by the utilization of a special inlet section and the diverterless technique, which disposes the whole inlet in the shield of the head of UAV, improving the drag characteristics and the stealthy performance of the aircraft; (3) The bump which is equal to the local boundary layer thickness in height can divert the boundary layer effectively. As a result, no obvious low total pressure zone is found at the outlet of the inlet; (4) According to the experimental results, negative angle of attack is favorable to the total pressure recovery and positive angle of attack is favorable to the total pressure distortion, while yaw brings bad effects on both; (5) The design of cowl lip is of great importance to the inlet performance at yaw, therefore, further improvement of the inlet performance will rely on the lip shapes of the cowl chosen.展开更多
In the present paper, an ‘in-house＇ genetic algorithm was numerically and experimentally validated. The genetic algorithm was applied to an optimization problem for improving the aerodynamic performances of an aircr...In the present paper, an ‘in-house＇ genetic algorithm was numerically and experimentally validated. The genetic algorithm was applied to an optimization problem for improving the aerodynamic performances of an aircraft wing tip through upper surface morphing. The optimization was performed for 16 flight cases expressed in terms of various combinations of speeds, angles of attack and aileron deflections. The displacements resulted from the optimization were used during the wind tunnel tests of the wing tip demonstrator for the actuators control to change the upper surface shape of the wing. The results of the optimization of the flow behavior for the airfoil morphing upper-surface problem were validated with wind tunnel experimental transition results obtained with infra-red Thermography on the wing-tip demonstrator. The validation proved that the 2D numerical optimization using the ‘in-house＇ genetic algorithm was an appropriate tool in improving various aspects of a wing＇s aerodynamic performances.展开更多
For the purpose of establishing and validating aerodynamic performance predictions at transonic Mach numbers, a wind tunnel test was conducted in the High-Speed Tunnel（HST） of the German-Dutch Wind Tunnels. The test...For the purpose of establishing and validating aerodynamic performance predictions at transonic Mach numbers, a wind tunnel test was conducted in the High-Speed Tunnel（HST） of the German-Dutch Wind Tunnels. The test article is the aerodynamic validation model from the Chinese Aeronautical Establishment, which is a full-span scale model representation of a business jet aircraft. The wind tunnel test comprised of parallel deployments of balance, pressures, infrared thermography, and model marker measurement techniques. Dedicated investigations with a dummy support were conducted as well, in order to derive and correct for the interference that the support system imposed on the overall model loads. This enabled the establishment of a comprehensive dataset in which the steady overall model loads, the wing load distribution, the state of the wing boundary layer, and the aeroelastic wing shape were quantified for conditions up to and beyond the cruise Mach number of 0.85.展开更多
In aircraft wing design,engineers aim to provide the best possible aerodynamic performance under cruise flight conditions in terms of lift-to-drag ratio.Conventional control surfaces such as flaps,ailerons,variable wi...In aircraft wing design,engineers aim to provide the best possible aerodynamic performance under cruise flight conditions in terms of lift-to-drag ratio.Conventional control surfaces such as flaps,ailerons,variable wing sweep and spoilers are used to trim the aircraft for other flight conditions.The appearance of the morphing wing concept launched a new challenge in the area of overall wing and aircraft performance improvement during different flight segments by locally altering the flow over the aircraft＇s wings.This paper describes the development and application of a control system for an actuation mechanism integrated in a new morphing wing structure.The controlled actuation system includes four similar miniature electromechanical actuators disposed in two parallel actuation lines.The experimental model of the morphing wing is based on a full-scale portion of an aircraft wing,which is equipped with an aileron.The upper surface of the wing is a flexible one,being closed to the wing tip;the flexible skin is made of light composite materials.The four actuators are controlled in unison to change the flexible upper surface to improve the flow quality on the upper surface by delaying or advancing the transition point from laminar to turbulent regime.The actuators transform the torque into vertical forces.Their bases are fixed on the wing ribs and their top link arms are attached to supporting plates fixed onto the flexible skin with screws.The actuators push or pull the flexible skin using the necessary torque until the desired vertical displacement of each actuator is achieved.The four vertical displacements of the actuators,correlated with the new shape of the wing,are provided by a database obtained through a preliminary aerodynamic optimization for specific flight conditions.The control system is designed to control the positions of the actuators in real time in order to obtain and to maintain the desired shape of the wing for a specified flight condition.The feasibility and effectiveness of the developed control system by use of a proportional fuzzy feed-forward methodology are demonstrated experimentally through bench and wind tunnel tests of the morphing wing model.展开更多
The accuracy of fluctuating pressure test in wind tunnel is affected by the tube system. By employing contradistinctive experimental method, systematic study was conducted to investigate the effects of the tube system...The accuracy of fluctuating pressure test in wind tunnel is affected by the tube system. By employing contradistinctive experimental method, systematic study was conducted to investigate the effects of the tube system on fluctuating pressure. The analyzed tube system parameters include tube length, inside diameter, curvature, deflection angle, thickness, material, restrictor length,restrictor inside diameter, and restrictor place. It is found that all the tube system parameters mentioned above except tube curvature have non-negligible effects on fluctuating pressure. Based on the research results, test methods were presented for the fluctuating pressure measurement in low-speed wind tunnel, which can obviously improve the data accuracy but not lose test efficiency. The effectiveness of the method is verified by the wind tunnel test.展开更多
Based on numerical simulations,this study highlights the sedimentation and erosion problems around a sand barrier through the relationship between the shear stress of the surface around the sand barrier and the critic...Based on numerical simulations,this study highlights the sedimentation and erosion problems around a sand barrier through the relationship between the shear stress of the surface around the sand barrier and the critical shear stress of sand grains.The numerical simulation results were verified using data measured by the wind tunnel test.The results showed that when the porosity was the same,the size and position of the vortex on the leeward side of the sand barrier were related to the inlet wind speed.As the wind speed increased,the vortex volume increased and the positions of the separation and reattachment points moved toward the leeward side.When the porosity of the sand barrier was 30%,the strength of the acceleration zone above the sand barrier was the highest,and the strength of the acceleration zone was negatively correlated with the porosity.Sand erosion and sedimentation distance were related to wind speed.With an increase in wind speed,the sand grain forward erosion or reverse erosion areas on the leeward side of the sand barrier gradually replaced the sedimentation area.With an increase in porosity,the sand sedimentation distance on the leeward side of the sand barrier gradually shortened,and the sand erosion area gradually disappeared.The sand sedimentation distance on the leeward side of the sand barrier with 30%porosity was the longest.The numerical simulation results were in good agreement with the wind tunnel test results.Based on the sand erosion and sedimentation results of the numerical simulation and wind tunnel test,when the porosity was 30%,the protection effect of the High Density Polyethylene(HDPE)board sand barrier was best.展开更多
An active control technique utilizing piezoelectric actuators to alleviate gust-response loads of a large-aspect-ratio flexible wing is investigated. Piezoelectric materials have been extensively used for active vibra...An active control technique utilizing piezoelectric actuators to alleviate gust-response loads of a large-aspect-ratio flexible wing is investigated. Piezoelectric materials have been extensively used for active vibration control of engineering structures. In this paper, piezoelectric materials further attempt to suppress the vibration of the aeroelastic wing caused by gust. The motion equation of the flexible wing with piezoelectric patches is obtained by Hamilton＇s principle with the modal approach, and then numerical gust responses are analyzed, based on which a gust load alleviation（GLA） control system is proposed. The gust load alleviation system employs classic propor tional-integral-derivative（PID） controllers which treat piezoelectric patches as control actuators and acceleration as the feedback signal. By a numerical method, the control mechanism that piezoelectric actuators can be used to alleviate gust-response loads is also analyzed qualitatively. Furthermore, through low-speed wind tunnel tests, the effectiveness of the gust load alleviation active control technology is validated. The test results agree well with the numerical results. Test results show that at a certain frequency range, the control scheme can effectively alleviate the z and x wingtip accelerations and the root bending moment of the wing to a certain extent. The control system gives satisfying gust load alleviation efficacy with the reduction rate being generally over 20%.展开更多
A series of tests have been conducted using a Cryogenic Wind Tunnel to study the effect of Reynolds number(Re)on the aerodynamic force and surface pressure experienced by a high speed train.The test Reynolds number ha...A series of tests have been conducted using a Cryogenic Wind Tunnel to study the effect of Reynolds number(Re)on the aerodynamic force and surface pressure experienced by a high speed train.The test Reynolds number has been varied from 1 million to 10 million,which is the highest Reynolds number a wind tunnel has ever achieved for a train test.According to our results,the drag coefficient of the leading car decreases with higher Reynolds number for yaw angles up to 30º.The drag force coefficient drops about 0.06 when Re is raised from 1 million to 10 million.The side force is caused by the high pressure at the windward side and the low pressure generated by the vortex at the lee side.Both pressure distributions are not appreciably affected by Reynolds number changes at yaw angles up to 30°.The lift force coefficient increases with higher Re,though the change is small.At a yaw angle of zero the down force coefficient is reduced by a scale factor of about 0.03 when the Reynolds number is raised over the considered range.At higher yaw angles the lift force coefficient is reduced about 0.1.Similar to the side force coefficient,the rolling moment coefficient does not change much with Re.The magnitude of the pitching moment coefficient increases with higher Re.This indicates that the load on the front bogie is higher at higher Reynolds numbers.The yawing moment coefficient increases with Re.This effect is more evident at higher yaw angles.The yawing moment coefficient increases by about 6%when Re is raised from 1 million to 10 million.The influence of Re on the rolling moment coefficient around the leeward rail is relatively smaller.It increases by about 2%over the considered range of Re.展开更多
In recent years,the safety and comfort of road vehicles driving on bridges under crosswinds have attracted more attention due to frequent occurrences of wind-induced disasters.This study focuses on a container truck a...In recent years,the safety and comfort of road vehicles driving on bridges under crosswinds have attracted more attention due to frequent occurrences of wind-induced disasters.This study focuses on a container truck and CRH2 high-speed train as research targets.Wind tunnel experiments are performed to investigate shielding effects of trains on aerodynamic characteristics of trucks.The results show that aerodynamic interference between trains and trucks varies with positions of trains(upstream,downstream)and trucks(upwind,downwind)and numbers of trains.To summarize,whether the train is upstream or downstream of tracks has basically no effect on aerodynamic forces,other than moments,of a truck driving on windward sides of bridges(upwind).In contrast,the presence of trains on the bridge deck has a significant impact on aerodynamic characteristics of a truck driving on leeward sides(downwind)at the same time.The best shielding effect on lateral forces of trucks occurs when the train is located downstream of tracks.Finally,the pressure measuring system shows that only lift forces on trains are affected by trucks,while other forces and moments are primarily affected by adjacent trains.展开更多
A theoretical formulation for time-domain nonlinear aeroelastic analysis of a flexible wing model is presented and validated by wind tunnel tests. A strain-based beam model for nonlinear structural analysis is combine...A theoretical formulation for time-domain nonlinear aeroelastic analysis of a flexible wing model is presented and validated by wind tunnel tests. A strain-based beam model for nonlinear structural analysis is combined with the Unsteady Vortex Lattice Method(UVLM) to form the complete framework for aeroelastic analysis. The nonlinear second-order differential equations are solved by an implicit time integration scheme that incorporates a Newton-Raphson sub-iteration technique. An advanced fiber optic sensing technique is firstly used in a wind tunnel for measuring large structural deformations. In the theoretical study, the nonlinear flutter boundary is determined by analyzing the transient response about the nonlinear static equilibrium with a series of flow velocities. The gust responses of the wing model at various gust frequencies are also studied. Comparisons of the theoretical and experimental results show that the proposed method is suitable for determining the nonlinear flutter boundary and simulating the gust response of flexible wings in the time domain.展开更多
Well-designed airfoil is very important for high-performance rotor.This paper developed an efficient multi-objective and multi-constraint optimization design system for rotor airfoils based on RANS analysis,and verifi...Well-designed airfoil is very important for high-performance rotor.This paper developed an efficient multi-objective and multi-constraint optimization design system for rotor airfoils based on RANS analysis,and verified the performance of the optimized airfoil.Using CRA09-A as the baseline rotor airfoil,the CRA09-B optimized rotor airfoil was designed successfully.Combined with the foundation of high-precision rotor airfoil stationary test technology,the CRA09-B and CRA09-A rotor airfoils were tested in the S3 MA high-speed wind tunnel of ONERA.In order to correct the aerodynamic data,a single parameter linear wall pressure method is used to consider the tunnel effects.The results indicate that multi-objective and multi-constraint optimization design method developed in this study is reliable,and that CRA09-B optimized airfoil provides better stationary performance than CRA09-A airfoil in terms of maximum lift coefficient and lift-to-drag ratio.展开更多
In view of the separation form of the separator from the back of the carrier upward and from the side of the carrier outward, separation-safety research is carried out by taking the separation of a cluster munition as...In view of the separation form of the separator from the back of the carrier upward and from the side of the carrier outward, separation-safety research is carried out by taking the separation of a cluster munition as an example. In previous wind tunnel free-flight tests, the similarity law of vertical, downward, moving submunition was used to design submunitions at different positions in different initial-velocity directions, which resulted in large discrepancies between wind tunnel test results and real flight. In a wind tunnel test, each submunition has an independent time-reduction ratio with respect to the dispenser. Even if the separation trajectory of a single submunition is accurate, there will be errors in the position of each submunition at a given time. Therefore, it is necessary to determine the time-reduction ratio between submunitions, and to modify the test results later. In order to ensure the accuracy of wind tunnel test results, the similarity law of a freeflight test in a wind tunnel is derived in this paper. The time-correction scheme to ensure motion similarity between submunitions is solved. Numerical simulation is used to simulate the separation of a wind tunnel test and real aircraft, and the motion parameters of different submunitions are solved. The results show that the new similarity laws derived for different types of submunitions can greatly reduce the errors caused by previous similarity laws. In addition to the case for the separation of a cluster munition, the similarity law can also be applied to the free-flight test design of wind tunnels for vertical separation and horizontal separation of other kinds of aircraft.展开更多
The changes of three components of aerodynamic force were discussed with the attack angle conversion for three kinds of section models. Based on the project of Shanghai Yangtze River Bridge, the wind tunnel test was c...The changes of three components of aerodynamic force were discussed with the attack angle conversion for three kinds of section models. Based on the project of Shanghai Yangtze River Bridge, the wind tunnel test was conducted to obtain its three components of aerodynamic force including 75 conditions of the construction stage, the bridge without vehicles and the bridge with vehicles from - 12 degrees to ＋ 12 degrees. For the bridge with vehicles, the drag force coefficient and the absolute value of both lift coefficient and moment coefficient were decreased by the vehicles. The test resuh shows that the bridge railing and vehicles have much influence on the three components of aerodynamic force of the vehicle-bridge system for Shanghai Yangtze River Bridge.展开更多
The accuracy of model attitude measurement has an important impact on wind tunnel test results. Microelectromechanical System Inertial Measurement Unit(MEMS IMU) provides a feasible way to measure model attitudes with...The accuracy of model attitude measurement has an important impact on wind tunnel test results. Microelectromechanical System Inertial Measurement Unit(MEMS IMU) provides a feasible way to measure model attitudes with high accuracy. However, the installation error between MEMS IMU coordinate system and the body coordinate system of test models can make the accuracy of the model attitude measurement decrease. In wind tunnel tests, the installation error depends on the relationship between the IMU and the model mechanism before tests. Therefore, infield calibration in wind tunnel tests is necessary to reduce installation errors. To improve attitude measurement accuracy, the least squares quaternion calibration method based on MEMS IMU and six-position calibration procedure are proposed. High-precision three-axis turntable tests are performed. The pitch accuracy after calibration is higher than that before calibration in the angle of attack sweeping tests. The Root-Mean-Square Errors(RMSE) in the roll and yaw are within0.01°, which are smaller than those before calibration. In the roll sweeping tests, RMSE of three attitude angles decrease significantly. In hypersonic wind tunnel tests, the pitch errors before and after calibration are within 0.05° and 0.02° in the angle of attack sweeping tests without wind. In five angle of attack sweeping tests with wind, the deviation between the mean of the pitch and the pitch after the elastic angle correction is within 0.03° and the standard deviation of five tests is within 0.01°. The proposed method is confirmed to enhance the accuracy of attitude measurement effectively, which is convenient for engineering applications.展开更多
The design and application of morphing systems are ongoing issues compelling the aviation industry.The Clean Sky-program represents the most significant aeronautical research ever launched in Europe on advanced techno...The design and application of morphing systems are ongoing issues compelling the aviation industry.The Clean Sky-program represents the most significant aeronautical research ever launched in Europe on advanced technologies for greening next-generation aircraft.The primary purpose of the program is to develop new concepts aimed at decreasing the effects of aviation on the environment,increasing reliability,and promoting eco-friendly mobility.These ambitions are pursued through research on enabling technologies fostering noise and gas emissions reduction,mainly by improving aircraft aerodynamic performances.Within the Clean Sky framework,a multimodal morphing flap device was designed based on tight industrial requirements and tailored for large civil aircraft applications.The flap is deployed in one unique setting,and its cross section is morphed differently in take-off and landing to get the necessary extra lift for the specific flight phase.Moreover,during the cruise,the tip of the flap is deflected for load control and induced drag reduction.Before manufacturing the first flap prototype,a high-speed(Ma=0.3),large-scale test campaign(geometric scale factor 1:3)was deemed necessary to validate the performance improvements brought by this novel system at the aircraft level.On the other hand,the geometrical scaling of the flap prototype was considered impracticable due to the unscalability of the embedded mechanisms and actuators for shape transition.Therefore,a new architecture was conceived for the flap model to comply with the scaled dimensions requirements,withstand the relevant loads expected during the wind tunnel tests and emulate the shape transition capabilities of the true-scale flap.Simplified strategies were developed to effectively morph the model during wind tunnel tests while ensuring the robustness of each morphed configuration and maintaining adequate stiffness levels to prevent undesirable deviations from the intended aerodynamic shapes.Additionally,a simplified design was conceived for the flap-wing interface,allowing for quick adjustments of the flap setting and enabling load transmission paths like those arising between the full-scale flap and the wing.The design process followed for the definition of this challenging wind tunnel model has been addressed in this work,covering the definition of the conceptual layout,the numerical evaluation of the most severe loads expected during the test,and the verification of the structural layout by means of advanced finite element analyses.展开更多
In this study, a multi-input/multi-output（MIMO） time-delay feedback controller is designed to actively suppress the flutter instability of a multiple-actuated-wing（MAW） wind tunnel model in the low subsonic flow r...In this study, a multi-input/multi-output（MIMO） time-delay feedback controller is designed to actively suppress the flutter instability of a multiple-actuated-wing（MAW） wind tunnel model in the low subsonic flow regime. The unsteady aerodynamic forces of the MAW model are computed based on the doublet-lattice method（DLM）. As the first attempt, the conventional linear quadratic-Gaussian（LQG） controller is designed to actively suppress the flutter of the MAW model. However, because of the time delay in the control loop, the wind tunnel tests illustrate that the LQG-controlled MAW model has no guaranteed stability margins. To compensate the time delay, hence, a time-delay filter, approximated via the first-order Pade approximation, is added to the LQG controller. Based on the time-delay feedback controller, a new digital control system is constructed by using a fixed-point and embedded digital signal processor（DSP） of high performance. Then, a number of wind tunnel tests are implemented based on the digital control system.The experimental results show that the present time-delay feedback controller can expand the flutter boundary of the MAW model and suppress the flutter instability of the open-loop aeroelastic system effectively.展开更多
Aiming at the safety problem of the stage separation of parallel reusable high-speed air vehicles,this paper studies the unsteady test method and focuses on deriving a similarity law of parallel stage separation free-...Aiming at the safety problem of the stage separation of parallel reusable high-speed air vehicles,this paper studies the unsteady test method and focuses on deriving a similarity law of parallel stage separation free-flight wind tunnel tests.The new similarity law considers the influences of aerodynamic force and gravity on the motions of the two stages,as well as the influence of aerodynamic interference between the two stages on each other’s motion.From the perspective of multiangle physical equations,the conditions to ensure that the two-stage separation trajectory of a wind tunnel test is similar to that of a real air vehicle are derived innovatively,so as to ensure the authenticity and credibility of wind tunnel test results.The similarity law is verified by an HIFiRE-5 air vehicle,and the separation trajectories of wind tunnel tests and the real air vehicle are obtained by numerical simulation.The research shows that the similarity law derived in this paper can ensure that wind tunnel free-flight tests have the ability to predict the two-stage separation characteristics of real parallel vehicles.By analyzing the separation trajectory curve of the typical state,it is found that the new method can ensure that the trajectory error of a wind tunnel test does not exceed 1%,which indicates that this method is credible.The establishment of the new method lays the foundation for subsequent wind tunnel tests and provides support for research on the safety of the stage separation of parallel reusable air vehicles.展开更多
基金Project(50978063) supported by the National Science Foundation of ChinaProject(NCET-09-0082) supported by the Program for New Century Excellent Talents in Chinese UniversitiesProject(121072) supported by the Fok Ying-Tong Education Foundation for Young Teachers in the Higher Education Institutions of China
文摘A wind tunnel test was conducted for a large steel gymnasium structure. Simultaneous pressure measurements were made on its entire ellipsoidal roof in a simulated suburban boundary layer flow field. Special attention is paid to the charaeteristics of fluctuating wind pressures in different zones on the roof. Some selected results are presented： 1） correlations between fluctuating wind pressures on both roof surfaces, 2） eigenvalues and eigenvectors of covariance matrices of the fluctuating wind pressures, 3） probability distributions of the fluctuating wind pressures, and 4） statistical characteristics of peak factor. Furthermore, the applicability of the quasi-steady approach is discussed in detail. Based on the results, an empirical formula for estimating the minimum pressure coefficients, using a peak factor approach, is presented. Comparison of the minimum pressure coefficients determined by the proposed formula and those obtained from the wind tunnel tests is made to examine the applicability and accuracy of the proposed formula.
基金supported by the National Natural Science Foundation of China(Nos.12272104,U22B2013).
文摘High-aspect-ratio aircraft are widely used in military and civilian fields,such as reconnaissance,surveillance,and attacks,due to their high lift-to-drag ratio,strong payload capability,significant endurance effect,and good stealth performance.However,compared to conventional aircraft,high-aspect-ratio aircraft are more susceptible to gust disturbances during flight.In response to this phenomenon,a full-scale dynamic model of a high-aspect-ratio unmanned aerial vehicle was developed.Considering the coupling among control surfaces,structural forces,and aerodynamic forces,along with sensor,actuator,and delay effects,an H_(∞)control law was designed using the principle of singular value energy flow reduction and weighted function,with a PID(Proportional-Integral-Derivative)control law for comparison.The two controllers were then subjected to pulse-response and jury stability tests.Finally,wind tunnel tests were conducted to investigate the gust alleviation principle,in which gust disturbances were generated using gust generators and control surface self-excitation.The results present that the average wing root bending moment and wing tip overload under the PID control law decrease by approximately 30%,while under the H_(∞)control law,both the average wing root bending moment and wing tip overload reduction rate exceed 50%,with peaks reaching 60%.This validates the feasibility and efficiency of the designed H_(∞)controller.
文摘The flutter characteristics of folding control fins with freeplay are investigated by numer- ical simulation and flutter wind tunnel tests. Based on the characteristics of the structures, fins with different freeplay angles are designed. For a 0° angle of attack, wind tunnel tests of these fins are conducted, and vibration is observed by accelerometers and a high-speed camera. By the expansion of the connected relationships, the governing equations of fit for the nonlinear aeroelastic analysis are established by the free-interface component mode synthesis method. Based on the results of the wind tunnel tests, the flutter characteristics of fins with different freeplay angles are analyzed. The results show that the vibration divergent speed is increased, and the divergent speed is higher than the flutter speed of the nominal linear system. The vibration divergent speed is increased along with an increase in the freeplay angle. The developed free-interface component mode synthesis method could be used to establish governing equations and to analyze the characteristics of nonlinear aeroe- lastic systems. The results of the numerical simulations and the wind tunnel tests indicate the same trends and critical velocities.
文摘Combined with a UAV of the shape like Global Hawk, a new inlet is advanced to obtain high performance in both Radar Cross Section(RCS) and aerodynamic drag. Efforts are made to achieve this goal such as adopting a top-mounted inlet configuration, utilizing the diverterless technique and putting forward a new shape of entrance. A design method is brought forward and verified by wind tunnel tests. Results indicate: (1) Despite the negative effect of the front fuselage and the absence of the conventional boundary diverter, the performance of the top-mounted diverterless inlet advanced here(Ma:0.50-0.70, α:-4°-6°,σ>0.975) is equivalent to that of conventional S shaped inlet with diverter; (2) The integration of the inlet with the fuselage is realized by the utilization of a special inlet section and the diverterless technique, which disposes the whole inlet in the shield of the head of UAV, improving the drag characteristics and the stealthy performance of the aircraft; (3) The bump which is equal to the local boundary layer thickness in height can divert the boundary layer effectively. As a result, no obvious low total pressure zone is found at the outlet of the inlet; (4) According to the experimental results, negative angle of attack is favorable to the total pressure recovery and positive angle of attack is favorable to the total pressure distortion, while yaw brings bad effects on both; (5) The design of cowl lip is of great importance to the inlet performance at yaw, therefore, further improvement of the inlet performance will rely on the lip shapes of the cowl chosen.
基金Bombardier Aerospace,Thales Canada,The Consortium in Research and Aerospace in Canada(CRIAQ)the Natural Sciences and Engineering Research Council of Canada(NSERC)for their financial support
文摘In the present paper, an ‘in-house＇ genetic algorithm was numerically and experimentally validated. The genetic algorithm was applied to an optimization problem for improving the aerodynamic performances of an aircraft wing tip through upper surface morphing. The optimization was performed for 16 flight cases expressed in terms of various combinations of speeds, angles of attack and aileron deflections. The displacements resulted from the optimization were used during the wind tunnel tests of the wing tip demonstrator for the actuators control to change the upper surface shape of the wing. The results of the optimization of the flow behavior for the airfoil morphing upper-surface problem were validated with wind tunnel experimental transition results obtained with infra-red Thermography on the wing-tip demonstrator. The validation proved that the 2D numerical optimization using the ‘in-house＇ genetic algorithm was an appropriate tool in improving various aspects of a wing＇s aerodynamic performances.
文摘For the purpose of establishing and validating aerodynamic performance predictions at transonic Mach numbers, a wind tunnel test was conducted in the High-Speed Tunnel（HST） of the German-Dutch Wind Tunnels. The test article is the aerodynamic validation model from the Chinese Aeronautical Establishment, which is a full-span scale model representation of a business jet aircraft. The wind tunnel test comprised of parallel deployments of balance, pressures, infrared thermography, and model marker measurement techniques. Dedicated investigations with a dummy support were conducted as well, in order to derive and correct for the interference that the support system imposed on the overall model loads. This enabled the establishment of a comprehensive dataset in which the steady overall model loads, the wing load distribution, the state of the wing boundary layer, and the aeroelastic wing shape were quantified for conditions up to and beyond the cruise Mach number of 0.85.
基金the Consortium for Research and Innovation in Aerospace in Quebec(CRIAQ)the National Sciences and Engineering Research Council (NSERC) for their funding of the CRIAQ MDO 505 project
文摘In aircraft wing design,engineers aim to provide the best possible aerodynamic performance under cruise flight conditions in terms of lift-to-drag ratio.Conventional control surfaces such as flaps,ailerons,variable wing sweep and spoilers are used to trim the aircraft for other flight conditions.The appearance of the morphing wing concept launched a new challenge in the area of overall wing and aircraft performance improvement during different flight segments by locally altering the flow over the aircraft＇s wings.This paper describes the development and application of a control system for an actuation mechanism integrated in a new morphing wing structure.The controlled actuation system includes four similar miniature electromechanical actuators disposed in two parallel actuation lines.The experimental model of the morphing wing is based on a full-scale portion of an aircraft wing,which is equipped with an aileron.The upper surface of the wing is a flexible one,being closed to the wing tip;the flexible skin is made of light composite materials.The four actuators are controlled in unison to change the flexible upper surface to improve the flow quality on the upper surface by delaying or advancing the transition point from laminar to turbulent regime.The actuators transform the torque into vertical forces.Their bases are fixed on the wing ribs and their top link arms are attached to supporting plates fixed onto the flexible skin with screws.The actuators push or pull the flexible skin using the necessary torque until the desired vertical displacement of each actuator is achieved.The four vertical displacements of the actuators,correlated with the new shape of the wing,are provided by a database obtained through a preliminary aerodynamic optimization for specific flight conditions.The control system is designed to control the positions of the actuators in real time in order to obtain and to maintain the desired shape of the wing for a specified flight condition.The feasibility and effectiveness of the developed control system by use of a proportional fuzzy feed-forward methodology are demonstrated experimentally through bench and wind tunnel tests of the morphing wing model.
基金supported by the Pre-research Fund of Vibration and Noise Control Technology (No. 51334060101)
文摘The accuracy of fluctuating pressure test in wind tunnel is affected by the tube system. By employing contradistinctive experimental method, systematic study was conducted to investigate the effects of the tube system on fluctuating pressure. The analyzed tube system parameters include tube length, inside diameter, curvature, deflection angle, thickness, material, restrictor length,restrictor inside diameter, and restrictor place. It is found that all the tube system parameters mentioned above except tube curvature have non-negligible effects on fluctuating pressure. Based on the research results, test methods were presented for the fluctuating pressure measurement in low-speed wind tunnel, which can obviously improve the data accuracy but not lose test efficiency. The effectiveness of the method is verified by the wind tunnel test.
基金financially supported by the fellowship of the China Postdoctoral Science Foundation(2021M703466)the Natural Science Foundation of Gansu Province,China(20JR10RA231)+1 种基金the Basic Research Innovation Group Project of Gansu Province,China(21JR7RA347)an Special Funds for Guiding Local Scientific and Technological Development by the Central Government(22ZY1QA005)。
文摘Based on numerical simulations,this study highlights the sedimentation and erosion problems around a sand barrier through the relationship between the shear stress of the surface around the sand barrier and the critical shear stress of sand grains.The numerical simulation results were verified using data measured by the wind tunnel test.The results showed that when the porosity was the same,the size and position of the vortex on the leeward side of the sand barrier were related to the inlet wind speed.As the wind speed increased,the vortex volume increased and the positions of the separation and reattachment points moved toward the leeward side.When the porosity of the sand barrier was 30%,the strength of the acceleration zone above the sand barrier was the highest,and the strength of the acceleration zone was negatively correlated with the porosity.Sand erosion and sedimentation distance were related to wind speed.With an increase in wind speed,the sand grain forward erosion or reverse erosion areas on the leeward side of the sand barrier gradually replaced the sedimentation area.With an increase in porosity,the sand sedimentation distance on the leeward side of the sand barrier gradually shortened,and the sand erosion area gradually disappeared.The sand sedimentation distance on the leeward side of the sand barrier with 30%porosity was the longest.The numerical simulation results were in good agreement with the wind tunnel test results.Based on the sand erosion and sedimentation results of the numerical simulation and wind tunnel test,when the porosity was 30%,the protection effect of the High Density Polyethylene(HDPE)board sand barrier was best.
基金supported by the National Key Research and Development Program (2016YFB 0200703)
文摘An active control technique utilizing piezoelectric actuators to alleviate gust-response loads of a large-aspect-ratio flexible wing is investigated. Piezoelectric materials have been extensively used for active vibration control of engineering structures. In this paper, piezoelectric materials further attempt to suppress the vibration of the aeroelastic wing caused by gust. The motion equation of the flexible wing with piezoelectric patches is obtained by Hamilton＇s principle with the modal approach, and then numerical gust responses are analyzed, based on which a gust load alleviation（GLA） control system is proposed. The gust load alleviation system employs classic propor tional-integral-derivative（PID） controllers which treat piezoelectric patches as control actuators and acceleration as the feedback signal. By a numerical method, the control mechanism that piezoelectric actuators can be used to alleviate gust-response loads is also analyzed qualitatively. Furthermore, through low-speed wind tunnel tests, the effectiveness of the gust load alleviation active control technology is validated. The test results agree well with the numerical results. Test results show that at a certain frequency range, the control scheme can effectively alleviate the z and x wingtip accelerations and the root bending moment of the wing to a certain extent. The control system gives satisfying gust load alleviation efficacy with the reduction rate being generally over 20%.
基金supported by a Major Programme of the National Science and Technology Support,China Grant(2013BAG24B00),under the project“Key technologies and engineering application demonstration of High-speed train for energy saving”.
文摘A series of tests have been conducted using a Cryogenic Wind Tunnel to study the effect of Reynolds number(Re)on the aerodynamic force and surface pressure experienced by a high speed train.The test Reynolds number has been varied from 1 million to 10 million,which is the highest Reynolds number a wind tunnel has ever achieved for a train test.According to our results,the drag coefficient of the leading car decreases with higher Reynolds number for yaw angles up to 30º.The drag force coefficient drops about 0.06 when Re is raised from 1 million to 10 million.The side force is caused by the high pressure at the windward side and the low pressure generated by the vortex at the lee side.Both pressure distributions are not appreciably affected by Reynolds number changes at yaw angles up to 30°.The lift force coefficient increases with higher Re,though the change is small.At a yaw angle of zero the down force coefficient is reduced by a scale factor of about 0.03 when the Reynolds number is raised over the considered range.At higher yaw angles the lift force coefficient is reduced about 0.1.Similar to the side force coefficient,the rolling moment coefficient does not change much with Re.The magnitude of the pitching moment coefficient increases with higher Re.This indicates that the load on the front bogie is higher at higher Reynolds numbers.The yawing moment coefficient increases with Re.This effect is more evident at higher yaw angles.The yawing moment coefficient increases by about 6%when Re is raised from 1 million to 10 million.The influence of Re on the rolling moment coefficient around the leeward rail is relatively smaller.It increases by about 2%over the considered range of Re.
基金Projects(52078504,51822803,51925808,U1934209)supported by the National Natural Science Foundation of ChinaProject(KF2021-05)supported by the State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures,China。
文摘In recent years,the safety and comfort of road vehicles driving on bridges under crosswinds have attracted more attention due to frequent occurrences of wind-induced disasters.This study focuses on a container truck and CRH2 high-speed train as research targets.Wind tunnel experiments are performed to investigate shielding effects of trains on aerodynamic characteristics of trucks.The results show that aerodynamic interference between trains and trucks varies with positions of trains(upstream,downstream)and trucks(upwind,downwind)and numbers of trains.To summarize,whether the train is upstream or downstream of tracks has basically no effect on aerodynamic forces,other than moments,of a truck driving on windward sides of bridges(upwind).In contrast,the presence of trains on the bridge deck has a significant impact on aerodynamic characteristics of a truck driving on leeward sides(downwind)at the same time.The best shielding effect on lateral forces of trucks occurs when the train is located downstream of tracks.Finally,the pressure measuring system shows that only lift forces on trains are affected by trucks,while other forces and moments are primarily affected by adjacent trains.
基金co-supported by the National Key Research and Development Program (No. 2016YFB0200703)Beijing Advanced Discipline Center for Unmanned Aircraft System。
文摘A theoretical formulation for time-domain nonlinear aeroelastic analysis of a flexible wing model is presented and validated by wind tunnel tests. A strain-based beam model for nonlinear structural analysis is combined with the Unsteady Vortex Lattice Method(UVLM) to form the complete framework for aeroelastic analysis. The nonlinear second-order differential equations are solved by an implicit time integration scheme that incorporates a Newton-Raphson sub-iteration technique. An advanced fiber optic sensing technique is firstly used in a wind tunnel for measuring large structural deformations. In the theoretical study, the nonlinear flutter boundary is determined by analyzing the transient response about the nonlinear static equilibrium with a series of flow velocities. The gust responses of the wing model at various gust frequencies are also studied. Comparisons of the theoretical and experimental results show that the proposed method is suitable for determining the nonlinear flutter boundary and simulating the gust response of flexible wings in the time domain.
基金supported by the National Natural Science Foundation of China(No.11902335)。
文摘Well-designed airfoil is very important for high-performance rotor.This paper developed an efficient multi-objective and multi-constraint optimization design system for rotor airfoils based on RANS analysis,and verified the performance of the optimized airfoil.Using CRA09-A as the baseline rotor airfoil,the CRA09-B optimized rotor airfoil was designed successfully.Combined with the foundation of high-precision rotor airfoil stationary test technology,the CRA09-B and CRA09-A rotor airfoils were tested in the S3 MA high-speed wind tunnel of ONERA.In order to correct the aerodynamic data,a single parameter linear wall pressure method is used to consider the tunnel effects.The results indicate that multi-objective and multi-constraint optimization design method developed in this study is reliable,and that CRA09-B optimized airfoil provides better stationary performance than CRA09-A airfoil in terms of maximum lift coefficient and lift-to-drag ratio.
基金supported by the Advanced Research Fund for Weapons and Equipment Development of China。
文摘In view of the separation form of the separator from the back of the carrier upward and from the side of the carrier outward, separation-safety research is carried out by taking the separation of a cluster munition as an example. In previous wind tunnel free-flight tests, the similarity law of vertical, downward, moving submunition was used to design submunitions at different positions in different initial-velocity directions, which resulted in large discrepancies between wind tunnel test results and real flight. In a wind tunnel test, each submunition has an independent time-reduction ratio with respect to the dispenser. Even if the separation trajectory of a single submunition is accurate, there will be errors in the position of each submunition at a given time. Therefore, it is necessary to determine the time-reduction ratio between submunitions, and to modify the test results later. In order to ensure the accuracy of wind tunnel test results, the similarity law of a freeflight test in a wind tunnel is derived in this paper. The time-correction scheme to ensure motion similarity between submunitions is solved. Numerical simulation is used to simulate the separation of a wind tunnel test and real aircraft, and the motion parameters of different submunitions are solved. The results show that the new similarity laws derived for different types of submunitions can greatly reduce the errors caused by previous similarity laws. In addition to the case for the separation of a cluster munition, the similarity law can also be applied to the free-flight test design of wind tunnels for vertical separation and horizontal separation of other kinds of aircraft.
基金Sponsored by the Key Project of the National Natural Science Foundation of China (Grant No.90715039)
文摘The changes of three components of aerodynamic force were discussed with the attack angle conversion for three kinds of section models. Based on the project of Shanghai Yangtze River Bridge, the wind tunnel test was conducted to obtain its three components of aerodynamic force including 75 conditions of the construction stage, the bridge without vehicles and the bridge with vehicles from - 12 degrees to ＋ 12 degrees. For the bridge with vehicles, the drag force coefficient and the absolute value of both lift coefficient and moment coefficient were decreased by the vehicles. The test resuh shows that the bridge railing and vehicles have much influence on the three components of aerodynamic force of the vehicle-bridge system for Shanghai Yangtze River Bridge.
文摘The accuracy of model attitude measurement has an important impact on wind tunnel test results. Microelectromechanical System Inertial Measurement Unit(MEMS IMU) provides a feasible way to measure model attitudes with high accuracy. However, the installation error between MEMS IMU coordinate system and the body coordinate system of test models can make the accuracy of the model attitude measurement decrease. In wind tunnel tests, the installation error depends on the relationship between the IMU and the model mechanism before tests. Therefore, infield calibration in wind tunnel tests is necessary to reduce installation errors. To improve attitude measurement accuracy, the least squares quaternion calibration method based on MEMS IMU and six-position calibration procedure are proposed. High-precision three-axis turntable tests are performed. The pitch accuracy after calibration is higher than that before calibration in the angle of attack sweeping tests. The Root-Mean-Square Errors(RMSE) in the roll and yaw are within0.01°, which are smaller than those before calibration. In the roll sweeping tests, RMSE of three attitude angles decrease significantly. In hypersonic wind tunnel tests, the pitch errors before and after calibration are within 0.05° and 0.02° in the angle of attack sweeping tests without wind. In five angle of attack sweeping tests with wind, the deviation between the mean of the pitch and the pitch after the elastic angle correction is within 0.03° and the standard deviation of five tests is within 0.01°. The proposed method is confirmed to enhance the accuracy of attitude measurement effectively, which is convenient for engineering applications.
基金carried out in the framework of AIRGREEN2 Project,which gratefully received funding from the Clean Sky 2 Joint Undertaking,under the European’s Union Horizon 2020 Research and Innovation Program,Grant Agreement(No.807089—REG GAM 4822018—H2020-IBA-CS2-GAMS-2017)funded by TUBITAK 2214-A-International Research Fellowship Programme for Ph.D.Students。
文摘The design and application of morphing systems are ongoing issues compelling the aviation industry.The Clean Sky-program represents the most significant aeronautical research ever launched in Europe on advanced technologies for greening next-generation aircraft.The primary purpose of the program is to develop new concepts aimed at decreasing the effects of aviation on the environment,increasing reliability,and promoting eco-friendly mobility.These ambitions are pursued through research on enabling technologies fostering noise and gas emissions reduction,mainly by improving aircraft aerodynamic performances.Within the Clean Sky framework,a multimodal morphing flap device was designed based on tight industrial requirements and tailored for large civil aircraft applications.The flap is deployed in one unique setting,and its cross section is morphed differently in take-off and landing to get the necessary extra lift for the specific flight phase.Moreover,during the cruise,the tip of the flap is deflected for load control and induced drag reduction.Before manufacturing the first flap prototype,a high-speed(Ma=0.3),large-scale test campaign(geometric scale factor 1:3)was deemed necessary to validate the performance improvements brought by this novel system at the aircraft level.On the other hand,the geometrical scaling of the flap prototype was considered impracticable due to the unscalability of the embedded mechanisms and actuators for shape transition.Therefore,a new architecture was conceived for the flap model to comply with the scaled dimensions requirements,withstand the relevant loads expected during the wind tunnel tests and emulate the shape transition capabilities of the true-scale flap.Simplified strategies were developed to effectively morph the model during wind tunnel tests while ensuring the robustness of each morphed configuration and maintaining adequate stiffness levels to prevent undesirable deviations from the intended aerodynamic shapes.Additionally,a simplified design was conceived for the flap-wing interface,allowing for quick adjustments of the flap setting and enabling load transmission paths like those arising between the full-scale flap and the wing.The design process followed for the definition of this challenging wind tunnel model has been addressed in this work,covering the definition of the conceptual layout,the numerical evaluation of the most severe loads expected during the test,and the verification of the structural layout by means of advanced finite element analyses.
基金supported in part by the National Natural Science Foundation of China (No. 10972100)
文摘In this study, a multi-input/multi-output（MIMO） time-delay feedback controller is designed to actively suppress the flutter instability of a multiple-actuated-wing（MAW） wind tunnel model in the low subsonic flow regime. The unsteady aerodynamic forces of the MAW model are computed based on the doublet-lattice method（DLM）. As the first attempt, the conventional linear quadratic-Gaussian（LQG） controller is designed to actively suppress the flutter of the MAW model. However, because of the time delay in the control loop, the wind tunnel tests illustrate that the LQG-controlled MAW model has no guaranteed stability margins. To compensate the time delay, hence, a time-delay filter, approximated via the first-order Pade approximation, is added to the LQG controller. Based on the time-delay feedback controller, a new digital control system is constructed by using a fixed-point and embedded digital signal processor（DSP） of high performance. Then, a number of wind tunnel tests are implemented based on the digital control system.The experimental results show that the present time-delay feedback controller can expand the flutter boundary of the MAW model and suppress the flutter instability of the open-loop aeroelastic system effectively.
基金supported by the National Natural Science Foundation of China(Nos.U21B2054 and 11772317).
文摘Aiming at the safety problem of the stage separation of parallel reusable high-speed air vehicles,this paper studies the unsteady test method and focuses on deriving a similarity law of parallel stage separation free-flight wind tunnel tests.The new similarity law considers the influences of aerodynamic force and gravity on the motions of the two stages,as well as the influence of aerodynamic interference between the two stages on each other’s motion.From the perspective of multiangle physical equations,the conditions to ensure that the two-stage separation trajectory of a wind tunnel test is similar to that of a real air vehicle are derived innovatively,so as to ensure the authenticity and credibility of wind tunnel test results.The similarity law is verified by an HIFiRE-5 air vehicle,and the separation trajectories of wind tunnel tests and the real air vehicle are obtained by numerical simulation.The research shows that the similarity law derived in this paper can ensure that wind tunnel free-flight tests have the ability to predict the two-stage separation characteristics of real parallel vehicles.By analyzing the separation trajectory curve of the typical state,it is found that the new method can ensure that the trajectory error of a wind tunnel test does not exceed 1%,which indicates that this method is credible.The establishment of the new method lays the foundation for subsequent wind tunnel tests and provides support for research on the safety of the stage separation of parallel reusable air vehicles.
