Press hardened steel(PHS)plays a key role in the manufacture of anti-collision structural components.The formation of δ-ferrite is a suffering issue for the laser welding of Al-Si coated PHS.Oscillating laser was use...Press hardened steel(PHS)plays a key role in the manufacture of anti-collision structural components.The formation of δ-ferrite is a suffering issue for the laser welding of Al-Si coated PHS.Oscillating laser was used to weld Al-Si coated 1.5 GPa PHS and novel 2 GPa PHS,and the effect of laser offset on the microstructure and properties of the dissimilar welded joints was studied.The results showed that a perfect weld profile was achieved by laser offset welding(LOW),without any welding defects.The δ-ferrite formed in as-received welds of laser alignment welding(LAW)with high Al content(up to 2.9 wt.%),but it disappeared with the laser offset to 2 GPa PHS,and the maximum Al content in the segregation zone reduced to 1.2 wt.%.After post-welding heat treatment,the δ-ferrite was coarsened and theα-ferrite formed in the secondary Al-rich area for the high Ac3 temperature,but the α-ferrite was few and fine in LOW welds.The hardness in the LAW welds was lower than that in the LOW welds,due to the presence of δ-ferrite,as well as less carbon content and Ti and V alloying elements.The tensile strength(1561 MPa)and elongation(5.4%)with LOW were higher than those with LAW(1490 MPa,3.1%),and the fracture occurred in the Al-Si coated PHS.It is indicated that adjusting the laser offset is effective to prevent the formation of δ-ferrite and is potential to avoid the formation of α-ferrite.It also provides a wide heat treatment temperature window for the dissimilar welds of 1.5 GPa PHS and novel 2 GPa PHS.展开更多
The influences of pin offset on the formation, microstructure and mechanical properties of friction stir welded joint of Ti6 Al4 V and AZ31 B Mg dissimilar alloys were investigated. The results show that sound joints ...The influences of pin offset on the formation, microstructure and mechanical properties of friction stir welded joint of Ti6 Al4 V and AZ31 B Mg dissimilar alloys were investigated. The results show that sound joints are obtained at different offsets. With the offset decreasing from 2.5 to 2.1 mm, the number of Ti alloy fragments is increased, and the stir zone(SZ) is enlarged and the grains in SZ become coarser. A hook-like structure is formed at the Mg/Ti interface and its length is increased with the decrease in pin offset. The Al element has an enrichment trend at the Ti alloy side near the Mg/Ti interface when the offset is decreased, which is beneficial to the bonding of the interface. An Al-rich layer with a thickness of 3–5μm forms at the offset of 2.1 mm. All the joints fracture at the interface and present a mixed ductile-and-brittle fracture mode. The joint tensile strength is increased with the offset decreasing from 2.5 to 2.1 mm, and the maximum tensile strength of 175 MPa is acquired at the offset of 2.1 mm.展开更多
Keyhole is one of the important phenomena in high-power laser welding process. By studying the keyhole characteristic and detecting the seam offset during high-power fiber laser welding, an infrared sensitive high-spe...Keyhole is one of the important phenomena in high-power laser welding process. By studying the keyhole characteristic and detecting the seam offset during high-power fiber laser welding, an infrared sensitive high-speed camera arranged off-axis orientation of laser beam was applied to capture the dynamic thermal images of a molten pool. The 304 austenitic stainless steel plate butt joint welding experiment with laser power 10 kW was carried out. Through analyzing the keyhole infrared image, the weld position was calculated. Least squares method was used to determine the actual weld position. Image filtering technique was used to process the keyhole image, and the keyhole centroid coordinate were calculated. Also, least squares method was used to fit the keyhole centroid curve equation and establish a nonlinear continuous model which described the deviation between keyhole centroid and weld seam. The heat accumulation effect affected by the infrared radiation was analyzed to determine whether the laser beam focus spot deviated from the desired welding seam. Experimental results showed that the keyhole centroid has related to the seam offset, and can reflect the welding quality.展开更多
Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） b...Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） by accounting for the combined effects of duty cycle β and offset α. The experimental measurements are in a good agreement with the results calculated by this new wire melting rate model, with the maximum discrepancy being less than 10%. Therefore it is evident that this new numerical model can successfully describe the dependence of wire melting rate on the duty cycle β and offset α.展开更多
基金financially supported by the funds of the National Natural Science Foundation of China(Nos.52005357 and U1908224)the support of Postdoctoral Research Foundation of China(2022M712308)Liaoning Revitalization Talents Program(No.XLYC2007066).
文摘Press hardened steel(PHS)plays a key role in the manufacture of anti-collision structural components.The formation of δ-ferrite is a suffering issue for the laser welding of Al-Si coated PHS.Oscillating laser was used to weld Al-Si coated 1.5 GPa PHS and novel 2 GPa PHS,and the effect of laser offset on the microstructure and properties of the dissimilar welded joints was studied.The results showed that a perfect weld profile was achieved by laser offset welding(LOW),without any welding defects.The δ-ferrite formed in as-received welds of laser alignment welding(LAW)with high Al content(up to 2.9 wt.%),but it disappeared with the laser offset to 2 GPa PHS,and the maximum Al content in the segregation zone reduced to 1.2 wt.%.After post-welding heat treatment,the δ-ferrite was coarsened and theα-ferrite formed in the secondary Al-rich area for the high Ac3 temperature,but the α-ferrite was few and fine in LOW welds.The hardness in the LAW welds was lower than that in the LOW welds,due to the presence of δ-ferrite,as well as less carbon content and Ti and V alloying elements.The tensile strength(1561 MPa)and elongation(5.4%)with LOW were higher than those with LAW(1490 MPa,3.1%),and the fracture occurred in the Al-Si coated PHS.It is indicated that adjusting the laser offset is effective to prevent the formation of δ-ferrite and is potential to avoid the formation of α-ferrite.It also provides a wide heat treatment temperature window for the dissimilar welds of 1.5 GPa PHS and novel 2 GPa PHS.
基金supported by the National Natural Science Foundation of China (No. 51705339)the Aeronautical Science Foundation of China (No. 20171125002)
文摘The influences of pin offset on the formation, microstructure and mechanical properties of friction stir welded joint of Ti6 Al4 V and AZ31 B Mg dissimilar alloys were investigated. The results show that sound joints are obtained at different offsets. With the offset decreasing from 2.5 to 2.1 mm, the number of Ti alloy fragments is increased, and the stir zone(SZ) is enlarged and the grains in SZ become coarser. A hook-like structure is formed at the Mg/Ti interface and its length is increased with the decrease in pin offset. The Al element has an enrichment trend at the Ti alloy side near the Mg/Ti interface when the offset is decreased, which is beneficial to the bonding of the interface. An Al-rich layer with a thickness of 3–5μm forms at the offset of 2.1 mm. All the joints fracture at the interface and present a mixed ductile-and-brittle fracture mode. The joint tensile strength is increased with the offset decreasing from 2.5 to 2.1 mm, and the maximum tensile strength of 175 MPa is acquired at the offset of 2.1 mm.
文摘Keyhole is one of the important phenomena in high-power laser welding process. By studying the keyhole characteristic and detecting the seam offset during high-power fiber laser welding, an infrared sensitive high-speed camera arranged off-axis orientation of laser beam was applied to capture the dynamic thermal images of a molten pool. The 304 austenitic stainless steel plate butt joint welding experiment with laser power 10 kW was carried out. Through analyzing the keyhole infrared image, the weld position was calculated. Least squares method was used to determine the actual weld position. Image filtering technique was used to process the keyhole image, and the keyhole centroid coordinate were calculated. Also, least squares method was used to fit the keyhole centroid curve equation and establish a nonlinear continuous model which described the deviation between keyhole centroid and weld seam. The heat accumulation effect affected by the infrared radiation was analyzed to determine whether the laser beam focus spot deviated from the desired welding seam. Experimental results showed that the keyhole centroid has related to the seam offset, and can reflect the welding quality.
文摘Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） by accounting for the combined effects of duty cycle β and offset α. The experimental measurements are in a good agreement with the results calculated by this new wire melting rate model, with the maximum discrepancy being less than 10%. Therefore it is evident that this new numerical model can successfully describe the dependence of wire melting rate on the duty cycle β and offset α.
基金National Natural Science Foundation of China(51265042)Special Plan Project for the Construction of Jiangxi Advantageous Scientific and Technological Innovation Team(20171BCB24007)Natural Science Foundation of Jiangxi Province(20114BAB206006)
