Waste heat generation,upgrading,and refrigeration are the fundamental ways to recover and utilize waste heat.Rationalizing the use of refrigerants also contributes to creating energy savings and minimizing carbon emis...Waste heat generation,upgrading,and refrigeration are the fundamental ways to recover and utilize waste heat.Rationalizing the use of refrigerants also contributes to creating energy savings and minimizing carbon emissions.This study evaluates the thermodynamics,economics,and environment of different refrigerants in three waste heat recovery schemes:generate electricity,heat pump,and refrigeration.Based on this,the entropy weight and technique for order preference by similarity to an ideal solution are combined to assess the overall performance of the refrigerants.A thorough analysis reveals that R1234ze(E)could replace R245fa and R123 in the organic Rankine cycle.The best refrigerant for vapor compression refrigeration and high-temperature heat pump systems is R1243zf.In addition,the multi-objective decision analysis shows that the performance difference among the nine selected refrigerants is the total cost,followed by the environmental impact.The approach successfully recognizes the variations between different refrigerants in the same waste heat recovery scheme and gives a thorough evaluation.It sets instructions for the future use of eco-friendly refrigerants and their application of waste heat recovery schemes.展开更多
To further enhance the recovery rate of low-temperature waste heat,the low-temperature flue gas in the sinter annular cooler was chosen as the heat source of an organic Rankine cycle(ORC)system,and the comprehensive e...To further enhance the recovery rate of low-temperature waste heat,the low-temperature flue gas in the sinter annular cooler was chosen as the heat source of an organic Rankine cycle(ORC)system,and the comprehensive evaluation of energy,exergy and economic performance of the ORC system was conducted deeply.The energy,exergy and economic performance models of the ORC system were established,and proper candidate organic working fluids(OWFs)were selected based on the thermo-physical properties of OWF and operating characteristics of ORC system.Then,the effects of ORC crucial parameters on the system energy,exergy and economic performances were evaluated in detail.Finally,the bi-objective optimization based on the genetic algorithm was conducted to analyze the optimal performance of the ORC system under the designed ORC crucial parameters,and the exergy efficiency and electricity production cost were set as the evaluation indexes of parametric optimization.The results indicate that the ORC system with the higher evaporation temperature and lower condensation temperature can obtain the larger system exergy efficiency and smaller electricity production cost.The smaller the superheat degree of OWF and pinch-point temperature difference in the evaporator are,the better the energy and exergy performances of the ORC system are.Under the optimization results,R245fa has the best comprehensive performance with the exergy efficiency of 46.34%and electricity production cost of 0.12123$/kWh among the selected candidate OWFs,which should be preferentially chosen as the OWF of the ORC system.展开更多
Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was c...Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.展开更多
Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rank...Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.展开更多
In order to improve the recovery and utilization rates of sinter waste heat effectively,the organic Rankine cycle(ORC)system with subcritical cycle was designed to recover the low-temperature sinter cooling flue gas w...In order to improve the recovery and utilization rates of sinter waste heat effectively,the organic Rankine cycle(ORC)system with subcritical cycle was designed to recover the low-temperature sinter cooling flue gas waste heat in an annular cooler for power generation.The thermodynamic,economic and multi-objective optimization models of ORC system were established,and R600a was selected as the ORC working medium.Subsequently,the variations in system thermodynamic performance and economic performance with the ORC thermal parameters were discussed in detail,and the optimal ORC thermal parameters were determined.The results show that the system net output power increases with increasing the evaporation temperature and decreasing the condensation temperature and increases first and then,decreases with the increase in superheat degree for a given flue gas outlet temperature in the evaporator,while the heat transfer area per unit net output power appears different variation trends in various ranges of flue gas outlet temperature.Taking the sinter cooling flue gas waste heat of 160℃as the ORC heat source,the optimal thermal parameters of ORC system were the flue gas outlet temperature of 90℃,the evaporation temperature of 95℃,the superheat degree of 10℃,and the condensation temperature of 28℃.展开更多
Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high sola...Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.展开更多
The common problem of cold strip continuous annealing furnaces is high exhaust gas temperature and great energy consumption. Taking the cold-strip continuous annealing furnaces of Baosteel No. 4 cold mill plant as an ...The common problem of cold strip continuous annealing furnaces is high exhaust gas temperature and great energy consumption. Taking the cold-strip continuous annealing furnaces of Baosteel No. 4 cold mill plant as an example, several waste heat recovery systems in the annealing furnaces are compared and their advantages and disadvantages are analyzed through different energy-saving technologies.展开更多
Data centers(DCs)are highly energy-intensive facilities,where about 30%–50%of the power consumed is attributable to the cooling of information technology equipment.This makes liquid cooling,especially in twophase mod...Data centers(DCs)are highly energy-intensive facilities,where about 30%–50%of the power consumed is attributable to the cooling of information technology equipment.This makes liquid cooling,especially in twophase mode,as an alternative to air cooling for the microprocessors in servers of interest.The need to meet the increased power density of server racks in high-performance DCs,along with the push towards lower global warming potential(GWP)refrigerants due to environmental concerns,has motivated research on the selection of two-phase heat transfer fluids for cooling servers while simultaneously recovering waste heat.With this regard,a heat pump-assisted absorption chiller(HPAAC)system for recovering waste heat in DCs with an on-chip twophase cooling loop driven by the compressor is proposed in the present paper and the low GWP hydrofluoroolefin refrigerants,including R1224yd(Z),R1233zd(E),R1234yf,R1234ze(E),R1234ze(Z),R1243zf and R1336mzz(Z),are evaluated and compared against R245fa as server coolant.For theHPAAC system,beginning with the development of energy and economic models,the performance is analyzed through both a parametric study and optimization using the coefficient of performance(COP),energy saving ratio(ESR),payback period(PBP)and net present value(NPV)as thermo-economic indicators.Using a standard vapor compression cooling system as a benchmark,the results indicate that with the evaporation temperature between 50℃and 70℃and the subcooling degree ranging from5℃to 15°C,R1233zd(E)with moderate compressor suction pressure and pressure ratio is the best refrigerant for the HPAAC systemwhile R1234yf performs the worst.More importantly,R1233zd(E)is also superior to R245fa based on thermo-economic performance,especially under work conditions with relatively lower evaporation temperature as well as subcooling degree.Under the given working conditions,the overall COP,ESR,NPV,and PBP of R1233zd(E)HPAAC with optimum subcooling degree range from4.99 to 11.27,25.53 to 64.59,1.13 to 4.10×10^(7) CNY and 5.77 to 2.22 years,respectively.Besides,the thermo-economic performance of R1233zd(E)HPAAC under optimum working conditions in terms of subcooling degree varying with the evaporation temperature is also investigated.展开更多
In this paper, a detailed thermodynamic analysis of the pure low-temperature waste heat recovery generation system is presented. The parameters affecting the system performance are compared to obtain the most signific...In this paper, a detailed thermodynamic analysis of the pure low-temperature waste heat recovery generation system is presented. The parameters affecting the system performance are compared to obtain the most significant ones; furthermore, parameter values are optimized for the largest power generating capability of the system. It is found that the most important parameters are inlet flue gas temperature, steam pressure and the pinch point temperature difference. There is an optimal superheated steam pressure value for giving the maximum generation power per unit flue gas. With the increase of inlet flue gas temperature, the generating power increases and the optimized steam pressure rises as well. However, with increase in pinch point temperature difference, the generating power decreases and the optimized steam pressure decreases as well. The theoretical calculation provides a theoretical basis for the parameters optimization in the design of the pure low-temperature waste heat recovery eeneration swtem展开更多
In recent years, China pays more attention to the protection of environment and resources in the process of social and economic development, puts forward the development concept of green, energy saving and environment...In recent years, China pays more attention to the protection of environment and resources in the process of social and economic development, puts forward the development concept of green, energy saving and environmental protection, and carries on a clear specification for the development of various industries. Under the current situation, flue gas waste heat recovery and utilization technology has attracted more and more attention, which can avoid the waste of energy and maximize the interests of enterprises. Therefore, relevant personnel should pay attention to study and analyze the application of flue gas waste heat recovery and utilization technology, in order to provide some help for the development of enterprises.展开更多
Using the boiler smoke waste heat, the actual energy saving reconstruction in case of boiler flue gas waste heat recovery and energy saving effect is analyzed, the design of waste heat recovery plan, improve the boile...Using the boiler smoke waste heat, the actual energy saving reconstruction in case of boiler flue gas waste heat recovery and energy saving effect is analyzed, the design of waste heat recovery plan, improve the boiler heating water temperature, in order to improve the boiler thermal efficiency, at the same time reduce the emissions of pollutants such as flue gas nitrogen oxides, achieve energy conservation and emissions reduction.展开更多
Two novel thermal cycles based on Brayton cycle and Rankine cycle are proposed, respectively, which integrate the recovery of low-level waste heat and Liquefied Nature Gas （LNG） cold energy utilization for power gen...Two novel thermal cycles based on Brayton cycle and Rankine cycle are proposed, respectively, which integrate the recovery of low-level waste heat and Liquefied Nature Gas （LNG） cold energy utilization for power generation. Cascade utilization of energy is realized in the two thermal cycles, where low-level waste heat,low-temperature exergy and pressure exergy of LNG are utilized efficiently through the system synthesis. The simulations are carried out using the commercial Aspen Plus 10.2, and the results are analyzed. Compared with the conventional Brayton cycle and Rankine cycle, the two novel cycles bring 60.94% and 60% in exergy efficiency, respectively and 53.08% and 52.31% in thermal efficiency, respectively.展开更多
During data center operation,it generates a significant volume of low-grade waste heat.To recover waste heat,a coupled system including solar collector,double effect absorption refrigeration and organic Rankine cycle ...During data center operation,it generates a significant volume of low-grade waste heat.To recover waste heat,a coupled system including solar collector,double effect absorption refrigeration and organic Rankine cycle is proposed.The system performance is analyzed in detail.For the organic Rankine cycle,five organic working fluids(R245fa,R245ca,R123,R11,and R113)are selected.R245fa,R113 and R245ca obtain the maximum net power output,thermal efficiency and exergy efficiency,respectively.In the double effect absorption refrigeration system,the evaporation temperature,condensation temperature,and generation pressure affect the COP and exergy efficiency.When the generator pressure is unchanged,the COP increases with increasing evaporation temperature and decreasing condensation temperature.When the COP reaches 1.3,the COP slightly decreases as the evaporation temperature or condensation temperature changes.Similarly,the exergy efficiency of refrigeration systems exhibits the same trend as the COP,and the exergy efficiency maximum value appears at approximately 0.32.A new performance indicator,rPUE,was defined to evaluate the data center power utilization efficiency.The flow distribution ratio and heat source temperature were optimized with multi-objective optimization.When the mass flow distribution rate is 0.6 and the heat source temperature is 441.5 K,rPUE and the total unit production costs of the system obtain the optimal solution.展开更多
Solid oxide fuel cell(SOFC)is an extremely promising technology for sustainable energy conversion and storage through highly efficient electrochemical reaction at high-temperature conditions.The existing studies commo...Solid oxide fuel cell(SOFC)is an extremely promising technology for sustainable energy conversion and storage through highly efficient electrochemical reaction at high-temperature conditions.The existing studies commonly address the final equilibrium state of the SOFC electrode reactions,giving less consideration to the micro kinetic of electrode reactions.In this paper,a kinetic model-based SOFC combined cycle power generation system is suggested to recover multiple waste heat,which includes a Kalina cycle(KC)as the bottom cycle and a Rankine cycle(RC)as the top cycle.In devneloping the proposed system,a novel kinetic model is presented for SOFC based on the microscopic mechanism of the oxygen reduction.A dynamic stochastic programming model is established to optimize the integrated system sequentially and simultaneously,with maximum power generation taken as the objective,depending on whether the SOFC system and the KC-RC system are simultaneously optimized.In sequential optimization,the output power of SOFC-KC-RC system is 320.56 kW and it is 415.04 kW using simultaneous optimization,achieving a 29.5%increase in power generation.Further comparison with the previous reports obtained by a thermodynamic model,this work leads to a 10.8%increase in power generation,showing the promising power production performance of the developed system.展开更多
A medium-temperature waste-heat recovery system based on the organic Rankine cycle (ORC) is designed to recover the exhaust energy from a heavy-duty diesel engine. Analysis of the 1st law of thermodynamics for an ORC ...A medium-temperature waste-heat recovery system based on the organic Rankine cycle (ORC) is designed to recover the exhaust energy from a heavy-duty diesel engine. Analysis of the 1st law of thermodynamics for an ORC system is performed. This analysis contains two parts. The first part is an analysis with undefined heat exchangers to gain an understanding of the ORC and find out suitable organic fluid parameters for a better ORC efficiency. The second part of the analysis uses combined engine test results and two designs of heat exchangers. By comparing the two designs, an improved system of heat exchangers is described. This analysis also quantifies the effect of engine parameters on ORC system. The study concludes that the supercritical Rankine cycle is a better approach towards waste heat recovery. The ORC system is found to perform better under part-load conditions if the medium-high power condition rather than rated working point of the engine is used as the design parameter. The ORC system achieves the highest waste-heat recovery efficiency of up to 10-15% for the optimised heat ex-changer design.展开更多
Hybrid electric vehicles(HEVs)are acknowledged to be an effective way to improve the efficiency of internal combustion engines(ICEs)and reduce fuel consumption.Although the ICE in an HEV can maintain high efficiency d...Hybrid electric vehicles(HEVs)are acknowledged to be an effective way to improve the efficiency of internal combustion engines(ICEs)and reduce fuel consumption.Although the ICE in an HEV can maintain high efficiency during driving,its thermal efficiency is approximately 40%,and the rest of the fuel energy is discharged through different kinds of waste heat.Therefore,it is important to recover the engine waste heat.Because of the great waste heat recovery performance of the organic Rankine cycle(ORC),an HEV integrated with an ORC(HEV-ORC)has been proposed.However,the addition of ORC creates a stiff and multi-energy problem,greatly increasing the complexity of the energy management system(EMS).Considering the great potential of deep reinforcement learning(DRL)for solving complex control problems,this work proposes a DRL-based EMS for an HEV-ORC.The simulation results demonstrate that the DRL-based EMS can save 2%more fuel energy than the rule-based EMS because the former provides higher average efficiencies for both engine and motor,as well as more stable ORC power and battery state.Furthermore,the battery always has sufficient capacity to store the ORC power.Consequently,DRL showed great potential for solving complex energy management problems.展开更多
In conventional photovoltaic(PV) systems, a large portion of solar energy is dissipated as waste heat since the generating efficiency is usually less than 30%. As the dissipated heat can be recovered for various appli...In conventional photovoltaic(PV) systems, a large portion of solar energy is dissipated as waste heat since the generating efficiency is usually less than 30%. As the dissipated heat can be recovered for various applications, the wasted heat recovery concentrator PV/thermal(WHR CPVT) hybrid systems have been developed. They can provide both electricity and usable heat by combining thermal systems with concentrator PV(CPV) module, which dramatically improves the overall conversion efficiency of solar energy.This paper systematically and comprehensively reviews the research and development of WHR CPVT systems. WHR CPVT systems with innovative design configurations, different theoretical evaluation models and experimental test processes for several implementations are presented in an integrated manner. We aim to provide a global point of view on the research trends, market potential, technical obstacles, and the future work which is required in the development of WHR CPVT technology. Possibly, it will offer a generic guide to the investigators who are interested in the study of WHR CPVT systems.展开更多
The paper proposes a novel pneumatic-fuel hybrid system,which combines a traditional internal combustion engine(ICE)and a pneumatic engine.One important merit of this concept is that the system can recover waste from ...The paper proposes a novel pneumatic-fuel hybrid system,which combines a traditional internal combustion engine(ICE)and a pneumatic engine.One important merit of this concept is that the system can recover waste from cooling water of internal combustion engine to optimize the working process of pneumatic engine,and thus to improve the entire efficiency of the hybrid system.Meanwhile,energy-saving effect due to lower cooling fan power can be achieved on ICE by waste heat recovery of pneumatic engine.Based on thermodynamic analysis,an experimental system is designed and established for verification.The experimental results show that the performance of pneumatic engine is improved when the waste heat recovery concept of the hybrid system is applied.Then an application example on a 4-cylinder engine is analyzed and discussed using numerical simulation.The results show that the fan power of the ICE cooling system can be saved up to 50%by applying the hybrid system.Considering the appreciable improvements on the energy efficiency with only limited system modifications when the concept is applied to traditional ICE based power systems,the proposed hybrid concept has the potential to serve as an alternative technology aiming for energy saving and emission reduction.展开更多
The Rankine cycle system for waste heat recovery of heavy-duty vehicle diesel engines has been regarded as a promising tech- nique to reduce fuel consumption. Its heat dissipation in the condensation process, however,...The Rankine cycle system for waste heat recovery of heavy-duty vehicle diesel engines has been regarded as a promising tech- nique to reduce fuel consumption. Its heat dissipation in the condensation process, however, should be take：l away in time, which is an energy-consuming process. A fan-assisted auxiliary water-cooling system is employed in this paper. Results at 1300 r/min and 50% load indicate that the cooling pump and cooling fan together consume 7.66% of the recovered power. What＇s worse for the heavy load, cooling accessories may deplete of all the recovered power of the Rankine cycle system. Af- terwards, effects of the condensing pressure and water feeding temperature are investigated, based on which a cooling power consumption model is established. Finally, an overall efficiency optimization is conducted to balance the electric power gener- ation and cooling power consumption, taking condensing pressure, pressure ratio and exhaust bypass valve as major variables. The research suggests that the priority is to increase condensing pressure and open exhaust bypass valve appropriately at high speed and heavy load to reduce the cooling power consumption, while at low speed and light load, a lower condensing pressure is favored and the exhaust bypass valve should be closed making the waste heat recovered as much as possible. Within the sub-critical region, a larger pressure ratio yields higher overall efficiency improvement at medium-low speed and load. But the effects taper off at high speed and heavy load. For a given vehicular heavy-duty diesel engine, the overall e：＇ficiency can be improved by 3.37% at 1300 r/min and 25% load using a Rankine cycle system to recover exhaust energy. The improvement becomes smaller as engine speed and load become higher.展开更多
Waste heat recovery(WHR)is one of the most useful ways to improve the efficiency of internal combustion engines,and an electricity-cooling cogeneration system(ECCS)based on Rankin-absorption refrigeration combined cyc...Waste heat recovery(WHR)is one of the most useful ways to improve the efficiency of internal combustion engines,and an electricity-cooling cogeneration system(ECCS)based on Rankin-absorption refrigeration combined cycle for the WHR of gaseous fuel engines is proposed in the paper.This system can avoid wasting the heat in condenser so that the efficiency of the whole WHR system improves,but the condensing temperature of Rankin cycle(RC)must increase in order to use absorption refrigeration system,which leads to the decrease of RC output power.Therefore,the relationship between the profit of absorption refrigeration system and the loss of RC in this combined system is the mainly studied content in the paper.Because the energy quality of cooling and electricity are different,cooling power in absorption refrigeration is converted to corresponding electrical power consumed by electric cooling system,which is defined as equivalent electrical power.With this method,the effects of some important operation parameters on the performance of the ECCS are researched,and the equivalent efficiency,exergy efficiency and primary energy rate are compared in the paper.展开更多
基金supported by the National Natural Science Foundation of China(22178190)the National Youth Natural Science Foundation of China(22408195).
文摘Waste heat generation,upgrading,and refrigeration are the fundamental ways to recover and utilize waste heat.Rationalizing the use of refrigerants also contributes to creating energy savings and minimizing carbon emissions.This study evaluates the thermodynamics,economics,and environment of different refrigerants in three waste heat recovery schemes:generate electricity,heat pump,and refrigeration.Based on this,the entropy weight and technique for order preference by similarity to an ideal solution are combined to assess the overall performance of the refrigerants.A thorough analysis reveals that R1234ze(E)could replace R245fa and R123 in the organic Rankine cycle.The best refrigerant for vapor compression refrigeration and high-temperature heat pump systems is R1243zf.In addition,the multi-objective decision analysis shows that the performance difference among the nine selected refrigerants is the total cost,followed by the environmental impact.The approach successfully recognizes the variations between different refrigerants in the same waste heat recovery scheme and gives a thorough evaluation.It sets instructions for the future use of eco-friendly refrigerants and their application of waste heat recovery schemes.
基金the financial support for this work provided by the National Natural Science Foundation of China(51974087)Anhui Provincial Natural Science Foundation(1908085QE203)+1 种基金University Natural Science Research Foundation of Anhui Province(2022AH050262)Science Research Foundation of Anhui Jianzhu University(2020QDZ02).
文摘To further enhance the recovery rate of low-temperature waste heat,the low-temperature flue gas in the sinter annular cooler was chosen as the heat source of an organic Rankine cycle(ORC)system,and the comprehensive evaluation of energy,exergy and economic performance of the ORC system was conducted deeply.The energy,exergy and economic performance models of the ORC system were established,and proper candidate organic working fluids(OWFs)were selected based on the thermo-physical properties of OWF and operating characteristics of ORC system.Then,the effects of ORC crucial parameters on the system energy,exergy and economic performances were evaluated in detail.Finally,the bi-objective optimization based on the genetic algorithm was conducted to analyze the optimal performance of the ORC system under the designed ORC crucial parameters,and the exergy efficiency and electricity production cost were set as the evaluation indexes of parametric optimization.The results indicate that the ORC system with the higher evaporation temperature and lower condensation temperature can obtain the larger system exergy efficiency and smaller electricity production cost.The smaller the superheat degree of OWF and pinch-point temperature difference in the evaporator are,the better the energy and exergy performances of the ORC system are.Under the optimization results,R245fa has the best comprehensive performance with the exergy efficiency of 46.34%and electricity production cost of 0.12123$/kWh among the selected candidate OWFs,which should be preferentially chosen as the OWF of the ORC system.
基金financially supported by the National Natural Science Foundation of China(No.51972019)the National Key Research and Development Program of China(No.2019YFC1905702)。
文摘Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.
基金Project(2009Gk2009)supported by the Science and Technology Department Funds of Hunan Province,ChinaProject(12C0379)supported by the Scientific Research Fund of Hunan Province,ChinaProject(13QDZ04)supported by the Scientific Research Foundation for Doctors of Xiang Tan University,China
文摘Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.
基金support for this work provided by the National Natural Science Foundation of China(51974087 and 51904074)Anhui Provincial Natural Science Foundation(1908085QE203)+1 种基金Natural Science Research Foundation of Anhui Province University(2022AH050262)Science Research Foundation of Anhui Jianzhu University(2020QDZ02).
文摘In order to improve the recovery and utilization rates of sinter waste heat effectively,the organic Rankine cycle(ORC)system with subcritical cycle was designed to recover the low-temperature sinter cooling flue gas waste heat in an annular cooler for power generation.The thermodynamic,economic and multi-objective optimization models of ORC system were established,and R600a was selected as the ORC working medium.Subsequently,the variations in system thermodynamic performance and economic performance with the ORC thermal parameters were discussed in detail,and the optimal ORC thermal parameters were determined.The results show that the system net output power increases with increasing the evaporation temperature and decreasing the condensation temperature and increases first and then,decreases with the increase in superheat degree for a given flue gas outlet temperature in the evaporator,while the heat transfer area per unit net output power appears different variation trends in various ranges of flue gas outlet temperature.Taking the sinter cooling flue gas waste heat of 160℃as the ORC heat source,the optimal thermal parameters of ORC system were the flue gas outlet temperature of 90℃,the evaporation temperature of 95℃,the superheat degree of 10℃,and the condensation temperature of 28℃.
文摘Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.
文摘The common problem of cold strip continuous annealing furnaces is high exhaust gas temperature and great energy consumption. Taking the cold-strip continuous annealing furnaces of Baosteel No. 4 cold mill plant as an example, several waste heat recovery systems in the annealing furnaces are compared and their advantages and disadvantages are analyzed through different energy-saving technologies.
基金supported by the Key Science and Technology Project of China Southern Grid Co.,Ltd.(No.090000KK52220020).
文摘Data centers(DCs)are highly energy-intensive facilities,where about 30%–50%of the power consumed is attributable to the cooling of information technology equipment.This makes liquid cooling,especially in twophase mode,as an alternative to air cooling for the microprocessors in servers of interest.The need to meet the increased power density of server racks in high-performance DCs,along with the push towards lower global warming potential(GWP)refrigerants due to environmental concerns,has motivated research on the selection of two-phase heat transfer fluids for cooling servers while simultaneously recovering waste heat.With this regard,a heat pump-assisted absorption chiller(HPAAC)system for recovering waste heat in DCs with an on-chip twophase cooling loop driven by the compressor is proposed in the present paper and the low GWP hydrofluoroolefin refrigerants,including R1224yd(Z),R1233zd(E),R1234yf,R1234ze(E),R1234ze(Z),R1243zf and R1336mzz(Z),are evaluated and compared against R245fa as server coolant.For theHPAAC system,beginning with the development of energy and economic models,the performance is analyzed through both a parametric study and optimization using the coefficient of performance(COP),energy saving ratio(ESR),payback period(PBP)and net present value(NPV)as thermo-economic indicators.Using a standard vapor compression cooling system as a benchmark,the results indicate that with the evaporation temperature between 50℃and 70℃and the subcooling degree ranging from5℃to 15°C,R1233zd(E)with moderate compressor suction pressure and pressure ratio is the best refrigerant for the HPAAC systemwhile R1234yf performs the worst.More importantly,R1233zd(E)is also superior to R245fa based on thermo-economic performance,especially under work conditions with relatively lower evaporation temperature as well as subcooling degree.Under the given working conditions,the overall COP,ESR,NPV,and PBP of R1233zd(E)HPAAC with optimum subcooling degree range from4.99 to 11.27,25.53 to 64.59,1.13 to 4.10×10^(7) CNY and 5.77 to 2.22 years,respectively.Besides,the thermo-economic performance of R1233zd(E)HPAAC under optimum working conditions in terms of subcooling degree varying with the evaporation temperature is also investigated.
文摘In this paper, a detailed thermodynamic analysis of the pure low-temperature waste heat recovery generation system is presented. The parameters affecting the system performance are compared to obtain the most significant ones; furthermore, parameter values are optimized for the largest power generating capability of the system. It is found that the most important parameters are inlet flue gas temperature, steam pressure and the pinch point temperature difference. There is an optimal superheated steam pressure value for giving the maximum generation power per unit flue gas. With the increase of inlet flue gas temperature, the generating power increases and the optimized steam pressure rises as well. However, with increase in pinch point temperature difference, the generating power decreases and the optimized steam pressure decreases as well. The theoretical calculation provides a theoretical basis for the parameters optimization in the design of the pure low-temperature waste heat recovery eeneration swtem
文摘In recent years, China pays more attention to the protection of environment and resources in the process of social and economic development, puts forward the development concept of green, energy saving and environmental protection, and carries on a clear specification for the development of various industries. Under the current situation, flue gas waste heat recovery and utilization technology has attracted more and more attention, which can avoid the waste of energy and maximize the interests of enterprises. Therefore, relevant personnel should pay attention to study and analyze the application of flue gas waste heat recovery and utilization technology, in order to provide some help for the development of enterprises.
文摘Using the boiler smoke waste heat, the actual energy saving reconstruction in case of boiler flue gas waste heat recovery and energy saving effect is analyzed, the design of waste heat recovery plan, improve the boiler heating water temperature, in order to improve the boiler thermal efficiency, at the same time reduce the emissions of pollutants such as flue gas nitrogen oxides, achieve energy conservation and emissions reduction.
基金the Science and Technology Foundation of Shaanxi Province (No.2002K08-G9).
文摘Two novel thermal cycles based on Brayton cycle and Rankine cycle are proposed, respectively, which integrate the recovery of low-level waste heat and Liquefied Nature Gas （LNG） cold energy utilization for power generation. Cascade utilization of energy is realized in the two thermal cycles, where low-level waste heat,low-temperature exergy and pressure exergy of LNG are utilized efficiently through the system synthesis. The simulations are carried out using the commercial Aspen Plus 10.2, and the results are analyzed. Compared with the conventional Brayton cycle and Rankine cycle, the two novel cycles bring 60.94% and 60% in exergy efficiency, respectively and 53.08% and 52.31% in thermal efficiency, respectively.
基金the support provided by the National Natural Science Foundation of China(No.52106010)the Beijing Natural Science Foundation(3232037)the Fundamental Research Funds for the Central Universities(No.2024MS150)。
文摘During data center operation,it generates a significant volume of low-grade waste heat.To recover waste heat,a coupled system including solar collector,double effect absorption refrigeration and organic Rankine cycle is proposed.The system performance is analyzed in detail.For the organic Rankine cycle,five organic working fluids(R245fa,R245ca,R123,R11,and R113)are selected.R245fa,R113 and R245ca obtain the maximum net power output,thermal efficiency and exergy efficiency,respectively.In the double effect absorption refrigeration system,the evaporation temperature,condensation temperature,and generation pressure affect the COP and exergy efficiency.When the generator pressure is unchanged,the COP increases with increasing evaporation temperature and decreasing condensation temperature.When the COP reaches 1.3,the COP slightly decreases as the evaporation temperature or condensation temperature changes.Similarly,the exergy efficiency of refrigeration systems exhibits the same trend as the COP,and the exergy efficiency maximum value appears at approximately 0.32.A new performance indicator,rPUE,was defined to evaluate the data center power utilization efficiency.The flow distribution ratio and heat source temperature were optimized with multi-objective optimization.When the mass flow distribution rate is 0.6 and the heat source temperature is 441.5 K,rPUE and the total unit production costs of the system obtain the optimal solution.
基金supported by the financial support provided by the National Natural Science Foundation of China(Grant Nos.22008023,and 22178045)Fundamental Research Funds for the Central Universities(Grant No.DUT21RC(3)109).
文摘Solid oxide fuel cell(SOFC)is an extremely promising technology for sustainable energy conversion and storage through highly efficient electrochemical reaction at high-temperature conditions.The existing studies commonly address the final equilibrium state of the SOFC electrode reactions,giving less consideration to the micro kinetic of electrode reactions.In this paper,a kinetic model-based SOFC combined cycle power generation system is suggested to recover multiple waste heat,which includes a Kalina cycle(KC)as the bottom cycle and a Rankine cycle(RC)as the top cycle.In devneloping the proposed system,a novel kinetic model is presented for SOFC based on the microscopic mechanism of the oxygen reduction.A dynamic stochastic programming model is established to optimize the integrated system sequentially and simultaneously,with maximum power generation taken as the objective,depending on whether the SOFC system and the KC-RC system are simultaneously optimized.In sequential optimization,the output power of SOFC-KC-RC system is 320.56 kW and it is 415.04 kW using simultaneous optimization,achieving a 29.5%increase in power generation.Further comparison with the previous reports obtained by a thermodynamic model,this work leads to a 10.8%increase in power generation,showing the promising power production performance of the developed system.
基金supported by the National Natural Science Foundation of China (Grant No. 51076013)the Specialized Research Fund for the Doc-toral Program of Higher Education of China (Grant No. 20101101110008)
文摘A medium-temperature waste-heat recovery system based on the organic Rankine cycle (ORC) is designed to recover the exhaust energy from a heavy-duty diesel engine. Analysis of the 1st law of thermodynamics for an ORC system is performed. This analysis contains two parts. The first part is an analysis with undefined heat exchangers to gain an understanding of the ORC and find out suitable organic fluid parameters for a better ORC efficiency. The second part of the analysis uses combined engine test results and two designs of heat exchangers. By comparing the two designs, an improved system of heat exchangers is described. This analysis also quantifies the effect of engine parameters on ORC system. The study concludes that the supercritical Rankine cycle is a better approach towards waste heat recovery. The ORC system is found to perform better under part-load conditions if the medium-high power condition rather than rated working point of the engine is used as the design parameter. The ORC system achieves the highest waste-heat recovery efficiency of up to 10-15% for the optimised heat ex-changer design.
基金supported by the National Natural Science Foundation of China(Grant No.51906173)。
文摘Hybrid electric vehicles(HEVs)are acknowledged to be an effective way to improve the efficiency of internal combustion engines(ICEs)and reduce fuel consumption.Although the ICE in an HEV can maintain high efficiency during driving,its thermal efficiency is approximately 40%,and the rest of the fuel energy is discharged through different kinds of waste heat.Therefore,it is important to recover the engine waste heat.Because of the great waste heat recovery performance of the organic Rankine cycle(ORC),an HEV integrated with an ORC(HEV-ORC)has been proposed.However,the addition of ORC creates a stiff and multi-energy problem,greatly increasing the complexity of the energy management system(EMS).Considering the great potential of deep reinforcement learning(DRL)for solving complex control problems,this work proposes a DRL-based EMS for an HEV-ORC.The simulation results demonstrate that the DRL-based EMS can save 2%more fuel energy than the rule-based EMS because the former provides higher average efficiencies for both engine and motor,as well as more stable ORC power and battery state.Furthermore,the battery always has sufficient capacity to store the ORC power.Consequently,DRL showed great potential for solving complex energy management problems.
基金supported by the National Natural Science Foundation of China (51406051 and 51522602)the Beijing Municipal Science and Technology Project (Z161100002616039)the Fundamental Research Funds for the Central Universities (2016MS20)
文摘In conventional photovoltaic(PV) systems, a large portion of solar energy is dissipated as waste heat since the generating efficiency is usually less than 30%. As the dissipated heat can be recovered for various applications, the wasted heat recovery concentrator PV/thermal(WHR CPVT) hybrid systems have been developed. They can provide both electricity and usable heat by combining thermal systems with concentrator PV(CPV) module, which dramatically improves the overall conversion efficiency of solar energy.This paper systematically and comprehensively reviews the research and development of WHR CPVT systems. WHR CPVT systems with innovative design configurations, different theoretical evaluation models and experimental test processes for several implementations are presented in an integrated manner. We aim to provide a global point of view on the research trends, market potential, technical obstacles, and the future work which is required in the development of WHR CPVT technology. Possibly, it will offer a generic guide to the investigators who are interested in the study of WHR CPVT systems.
基金supported by the National Natural Science Foundation of China(Grant No.50976104)the National Basic Research Program of China("973" Program)(Grant No.2011CB707205)
文摘The paper proposes a novel pneumatic-fuel hybrid system,which combines a traditional internal combustion engine(ICE)and a pneumatic engine.One important merit of this concept is that the system can recover waste from cooling water of internal combustion engine to optimize the working process of pneumatic engine,and thus to improve the entire efficiency of the hybrid system.Meanwhile,energy-saving effect due to lower cooling fan power can be achieved on ICE by waste heat recovery of pneumatic engine.Based on thermodynamic analysis,an experimental system is designed and established for verification.The experimental results show that the performance of pneumatic engine is improved when the waste heat recovery concept of the hybrid system is applied.Then an application example on a 4-cylinder engine is analyzed and discussed using numerical simulation.The results show that the fan power of the ICE cooling system can be saved up to 50%by applying the hybrid system.Considering the appreciable improvements on the energy efficiency with only limited system modifications when the concept is applied to traditional ICE based power systems,the proposed hybrid concept has the potential to serve as an alternative technology aiming for energy saving and emission reduction.
基金supported by the National Basic Research Program of China("973"Project)(Grant No.2011CB707206)
文摘The Rankine cycle system for waste heat recovery of heavy-duty vehicle diesel engines has been regarded as a promising tech- nique to reduce fuel consumption. Its heat dissipation in the condensation process, however, should be take：l away in time, which is an energy-consuming process. A fan-assisted auxiliary water-cooling system is employed in this paper. Results at 1300 r/min and 50% load indicate that the cooling pump and cooling fan together consume 7.66% of the recovered power. What＇s worse for the heavy load, cooling accessories may deplete of all the recovered power of the Rankine cycle system. Af- terwards, effects of the condensing pressure and water feeding temperature are investigated, based on which a cooling power consumption model is established. Finally, an overall efficiency optimization is conducted to balance the electric power gener- ation and cooling power consumption, taking condensing pressure, pressure ratio and exhaust bypass valve as major variables. The research suggests that the priority is to increase condensing pressure and open exhaust bypass valve appropriately at high speed and heavy load to reduce the cooling power consumption, while at low speed and light load, a lower condensing pressure is favored and the exhaust bypass valve should be closed making the waste heat recovered as much as possible. Within the sub-critical region, a larger pressure ratio yields higher overall efficiency improvement at medium-low speed and load. But the effects taper off at high speed and heavy load. For a given vehicular heavy-duty diesel engine, the overall e：＇ficiency can be improved by 3.37% at 1300 r/min and 25% load using a Rankine cycle system to recover exhaust energy. The improvement becomes smaller as engine speed and load become higher.
基金supported by the National Basic Research Program of China("973"Project)(Gran No.2011CB707201)
文摘Waste heat recovery(WHR)is one of the most useful ways to improve the efficiency of internal combustion engines,and an electricity-cooling cogeneration system(ECCS)based on Rankin-absorption refrigeration combined cycle for the WHR of gaseous fuel engines is proposed in the paper.This system can avoid wasting the heat in condenser so that the efficiency of the whole WHR system improves,but the condensing temperature of Rankin cycle(RC)must increase in order to use absorption refrigeration system,which leads to the decrease of RC output power.Therefore,the relationship between the profit of absorption refrigeration system and the loss of RC in this combined system is the mainly studied content in the paper.Because the energy quality of cooling and electricity are different,cooling power in absorption refrigeration is converted to corresponding electrical power consumed by electric cooling system,which is defined as equivalent electrical power.With this method,the effects of some important operation parameters on the performance of the ECCS are researched,and the equivalent efficiency,exergy efficiency and primary energy rate are compared in the paper.
