Bubble breakup at T-junction microchannels is the basis for the numbering-up of gas−liquid two-phase flow in parallelized microchannels. This article presents the bubble breakup in viscous liquids at a microfluidic T-...Bubble breakup at T-junction microchannels is the basis for the numbering-up of gas−liquid two-phase flow in parallelized microchannels. This article presents the bubble breakup in viscous liquids at a microfluidic T-junction. Nitrogen is used as the gas phase, and glycerol-water mixtures with different mass concentration of glycerol as the liquid phase. The evolution of the gas−liquid interface during bubble breakup at the microfluidic T-junction is explored. The thinning of the bubble neck includes the squeezing stage and the rapid pinch-off stage. In the squeezing stage, the power law relation is found between the minimum width of the bubble neck and the time, and the values of exponents α1 and α2 are influenced by the viscous force. The values of pre-factors m_(1) and m_(2) are negatively correlated with the capillary number. In the rapid pinch-off stage, the thinning of the bubble neck is predominated by the surface tension, and the minimum width of the bubble neck can be scaled with the remaining time as power-law. The propagation of the bubble tip can be characterized by the power law between the movement distance and the time, with decreasing exponent as increased liquid viscosity.展开更多
Maximizing the efficiency of thermal engineering equipment involves minimizing entropy generation,which arises from irreversible processes.This study examines thermal transport and entropy generation in viscous flow o...Maximizing the efficiency of thermal engineering equipment involves minimizing entropy generation,which arises from irreversible processes.This study examines thermal transport and entropy generation in viscous flow over a radially stretching disk,incorporating the effects of magnetohydrodynamics(MHD),viscous dissipation,Joule heating,and radiation.Similarity transformations are used to obtain dimensionless nonlinear ordinary differential equations(ODEs)from the governing coupled partial differential equations(PDEs).The converted equations are then solved by using the BVP4C solver in MATLAB.To validate the findings,the results are compared with previously published studies under fixed parameter conditions,demonstrating strong agreement.Various key parameters are analyzed graphically to assess their impact on velocity and temperature distributions.Additionally,Bejan number and entropy generation variations are presented for different physical parameters.The injection parameter(S<0)increases the heat transfer rate,while the suction parameter(S>0)reduces it,exhibiting similar effects on fluid velocity.The magnetic parameter(M)effectively decreases entropy generation within the range of approximately 0≤η≤0.6.Beyond this interval,its influence diminishes as entropy generation values converge,with similar trends observed for the Bejan number.Furthermore,increased thermal radiation intensity is identified as a critical factor in enhancing entropy generation and the Bejan number.展开更多
This study examines the intricate occurrences of thermal and solutal Marangoni convection in three-layered flows of viscous fluids,with a particular emphasis on their relevance to renewable energy systems.This researc...This study examines the intricate occurrences of thermal and solutal Marangoni convection in three-layered flows of viscous fluids,with a particular emphasis on their relevance to renewable energy systems.This research examines the flow of a three-layered viscous fluid,considering the combined influence of heat and solutal buoyancy driven Rayleigh-Bénard convection,as well as thermal and solutal Marangoni convection.The homotopy perturbation method is used to examine and simulate complex fluid flow and transport phenomena,providing important understanding of the fundamental physics and assisting in the optimization of various battery configurations.The inquiry examines the primary elements that influence Marangoni convection and its impact on battery performance,providing insights on possible enhancements in energy storage devices.The findings indicate that the velocity profiles shown graphically exhibit a prominent core zone characterized by the maximum speed,which progressively decreases as it approaches the walls of the channel.This study enhances our comprehension of fluid dynamics and the transmission of heat and mass in intricate systems,which has substantial ramifications for the advancement of sustainable energy solutions.展开更多
Styrene-butadiene-styrene(SBS)modified asphalt(SA)has long found effective applications in road construction materials.When combined with fillers,SBS-modified asphalt has demonstrated promising resistance to fatigue c...Styrene-butadiene-styrene(SBS)modified asphalt(SA)has long found effective applications in road construction materials.When combined with fillers,SBS-modified asphalt has demonstrated promising resistance to fatigue cracking caused by temperature fluctuations and aging.In this study,molybdenum disulfide(MoS_(2))and polyphosphoric acid(PPA)were ground in naphthenic oil(NO)and subjected to mechanical activation to create PPAmodified MoS_(2),referred to as OMS-PPA.By blending various ratios of OMS-PPA with SBS-modified asphalt,composite-modified asphalts were successfully developed to enhance their overall properties.To assess the mechanical characteristics and stability of these modified asphalts,various methods were employed,including penetration factor,flow activation energy,fluorescence microscopy,and dynamic shear rheology.Additionally,the short-term aging performance was evaluated using Fourier transform infrared(FTIR)spectroscopy and nanoindentation tests.The results revealed a 3.7%decrease in the penetration-temperature coefficient for SAOMS compared to SA,while 1-SA-OMS-PPA showed an even greater reduction of 7.1%.Furthermore,after short-term aging,carboxyl group generation in SA increased by 5.93%,while SA-OMS exhibited a smaller rise of 1.36%,and 1-SA-OMS-PPA saw an increase of just 0.93%.The study also highlighted significant improvements in the hardness of these materials.The hardness change ratio for SA-OMS decreased by 43.08%,while the ratio for 1-SA-OMS-PPA saw a notable reduction of 65.16% compared to unmodified SA.These findings suggest that OMS-PPA contributed to improvements in temperature sensitivity,particle dispersibility,and resistance to shortterm aging in asphalts.The results hold significant promise for the future development of advanced asphalt-based materials with potential high-value applications in flexible pavements for highways.展开更多
Drying operations are of grave importance to realize the reduction and utilization of sewage sludge resources,but the conventional thermal evaporation drying(TED)technology presents challenges due to the need for a la...Drying operations are of grave importance to realize the reduction and utilization of sewage sludge resources,but the conventional thermal evaporation drying(TED)technology presents challenges due to the need for a large amount of thermal energy to conquer the phase-change latent heat of moisture.Herein,we report a non-phase change technology based on particle high-speed self-rotation in a cyclone for fast,low-temperature drying of viscous sludge with high-moisture contents.Dispersed phase medium(DPM)is introduced into the cyclone self-rotation drying(CSRD)reactor to enhance the dispersion of the viscous sludge.The effects of carrier gas temperature,feeding rate,size,and proportion of DPM particles in the drying process are systematically examined.Under optimal operating conditions,the weighted content of moisture in the viscous sludge could be reduced from 80%to 15.01%in less than 5 s,achieving a high drying efficiency of 95.79%.Theoretical calculations also reveal that 89.26%of the moisture is removed through non-phase change pathway,contributing to a 522-fold increase in the drying rate of CSRD compared to TED technology.This investigation presents a sustainable effective approach for high moisture viscous sludge treatment with low energy consumption and carbon emissions.展开更多
Studying immiscible fluid displacement patterns can provide a better understanding of displacement processes within heterogeneous porous media,thereby helping improving oil recovery and optimizing geological CO_(2) se...Studying immiscible fluid displacement patterns can provide a better understanding of displacement processes within heterogeneous porous media,thereby helping improving oil recovery and optimizing geological CO_(2) sequestration.As the injection rate of water displacing oil increases and the displacement pattern transits from capillary fingering to viscous fingering,there is a broad crossover zone between the two that can adversely affect the oil displacement efficiency.While previous studies have utilized phase diagrams to investigate the influence of the viscosity ratio and wettability of the crossover zone,fewer have studied the impact of rock heterogeneity.In this study,we created pore network models with varying degrees of heterogeneity to simulate water flooding at different injection rates.Our model quantifies capillary and viscous fingering characteristics while investigating porous media heterogeneity's role in the crossover zone.Analysis of simulation results reveals that a higher characteristic front flow rate within the crossover zone leads to earlier breakthrough and reduced displacement efficiency.Increased heterogeneity in the porous media raises injection-site pressure,lowers water saturation,and elevates the characteristic front flow rate,thereby expanding the extent of crossover zone.展开更多
In this paper,we consider the initial boundary value problem for the 2-D hyperbolic viscous Cahn-Hilliard equation.Firstly,we prove the existence and uniqueness of the local solution by the Galerkin method and contrac...In this paper,we consider the initial boundary value problem for the 2-D hyperbolic viscous Cahn-Hilliard equation.Firstly,we prove the existence and uniqueness of the local solution by the Galerkin method and contraction mapping principle.Then,using the potential well theory,we study the global well-posedness of the solution with initial data at different levels of initial energy,i.e.,subcritical initial energy,critical initial energy and arbitrary positive initial energy.For subcritical initial energy,we prove the global existence,asymptotic behavior and finite time blowup of the solution.Moreover,we extend these results to the critical initial energy using the scaling technique.For arbitrary positive initial energy,including the sup-critical initial energy,we obtain the sufficient conditions for finite time blow-up of the solution.As a further study for estimating the blowup time,we give a unified expression of the lower bound of blowup time for all three initial energy levels and estimate the upper bound of blowup time for subcritical and critical initial energy.展开更多
Based on the bulging principle of different ellipticity dies, the methyl vinyl silicone rubber with excellent thermal stability and heat transfer performance was chosen as the viscous medium. The finite element analys...Based on the bulging principle of different ellipticity dies, the methyl vinyl silicone rubber with excellent thermal stability and heat transfer performance was chosen as the viscous medium. The finite element analysis and experiments of viscous warm pressure bulging （VWPB） of AZ31B magnesium alloy were conducted to analyze the influence of different ellipticity dies on the formability of AZ31B magnesium alloy. At the same time, based on the grid strain rule, the forming limit diagram （FLD） of VWPB of AZ31B magnesium alloy was obtained through measuring the strain of bulging specimens. The results showed that at the temperature range of viscous medium thermal stability, the viscous medium can fit the geometry variation of sheet and generate non-uniform pressure field, and as the die ellipticity increases, the difference value of non-uniform pressure reduces. Meanwhile, according to the FLD, the relationship between part complexity and ultimate deformation was investigated.展开更多
Aim To get the analytical for laminar viscous flow in the gap of two parallel rotating disks. Methods By estimating the order of magnitude of each term in the Navier-Stokes equations to drop small terms and achieve...Aim To get the analytical for laminar viscous flow in the gap of two parallel rotating disks. Methods By estimating the order of magnitude of each term in the Navier-Stokes equations to drop small terms and achieve the required simplified differential equations, and by integrating the equations to obtain the solution for theflow between two rotary disks. Results Parameters related to the laminar viscous flow in the gap between two parallel rotary disks, such as the velocity, the pressure, the flowrate, the force, the shearing stress, the torque and the power derived. Conclusion The result provides a theoretical basis and an effective method for the designs of the devices connected with the laminar viscous flow in the gap between two parallel rotary disks.展开更多
The mean velocity estimation of debris flows, especially viscous debris flows, is an important part in the debris flow dynamics research and in the design of control structures. In this study, theoretical equations fo...The mean velocity estimation of debris flows, especially viscous debris flows, is an important part in the debris flow dynamics research and in the design of control structures. In this study, theoretical equations for computing debris flow velocity with the one-phase flow assumption were reviewed and used to analyze field data of viscous debris flows. Results show that the viscous debris flow is diffficult to be classified as a Newtonian laminar flow, a Newtonian turbulent flow, a Bingham fluid, or a dilatant fluid in the strict sense. However, we can establish empirical formulas to compute its mean velocity following equations for Newtonian turbulent flows, because most viscous debris flows are tur- bulent. Factors that potentially influence debris flow velocity were chosen according to two-phase flow theories. Through correlation analysis and data fitting, two empirical formulas were proposed. In the first one, velocity is expressed as a function of clay content, flow depth and channel slope. In the second one, a coefficient representing the grain size nonuniformity is used instead of clay content. Both formulas can give reasonable estimate of the mean velocity of the viscous debris flow.展开更多
A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions a...A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions according to Reynolds number.In the far-wall region,the thermal melt flow was calculated as Newtonian flow.In the near-wall region,the thermal melt flow was calculated as non-Newtonian flow.It was proved that the new algorithm based on the projection method with the implicit technique was correct through nonparametric statistics method and experiment.The simulation results show that the new algorithm based on the projection method with the implicit technique calculates more quickly than the solution algorithm-volume of fluid method using the explicit difference method.展开更多
Gridless method is developed for unsteady viscous flows involving moving boundaries. The point distri- bution of gridless method is implemented in an isotropic or anisotropic way according to the features of viscous f...Gridless method is developed for unsteady viscous flows involving moving boundaries. The point distri- bution of gridless method is implemented in an isotropic or anisotropic way according to the features of viscous flows. In the area far away from the body, the traditional cloud of isotropic points is used, while in the adjacent area, the cloud of anisotropic points is distributed. In this way, the point spacing normal to the wall can be small enough for simulating the boundary layer, and meanwhile, the total number of points in the computational do- main can be controlled due to large spacing in other tangential direction through the anisotropic way. A fast mov- ing technique of clouds of points at each time-step is presented based on the attenuation law of disturbed motion for unsteady flows involving moving boundaries. In the mentioned cloud of points, a uniform weighted least- square curve fit method is utilized to discretize the spatial derivatives of the Navier-Stokes equations. The pro- posed gridless method, coupled with a dual time-stepping method and the Spalart-Allmaras turbulence model, is implemented for the Navier-Stokes equations. The computational results of unsteady viscous flows around a NLR7301 airfoil with an oscillating flap and a pitching NACA0012 airfoil are presented in a good agreement with the available experimental data.展开更多
After nearly a decade of application and investigation, a motion amplification device with viscous dampers for energy dissipation has been recognized as an effective solution to mitigate wind or seismic excitation, es...After nearly a decade of application and investigation, a motion amplification device with viscous dampers for energy dissipation has been recognized as an effective solution to mitigate wind or seismic excitation, especially for stiff structural systems. As a result of compensation of amplified motion, it has been proved that the efficiency of viscous damper largely depends on the motion amplification device configuration, particularly for device stiflhess. In this paper, a ＂scissor-jack＂ type of motion amplification device, called a ＂toggle brace damper＂ system, is studied. It is demonstrated that the efficiency of such a device reflected by its amplification factor is not merely a function of its geometric configuration, but is highly dependent on the support elements＇ stiffness as well, similar to the mechanism of a leverage arm. Accordingly, a mathematical model in terms of complex modulus of the viscous damper with consideration of the support brace＇s stiffness is established. The results indicate that the efficiency of the motion amplification device with viscous dampers significantly depends on the stiffness of the support elements. Other parameters, such as toggle brace configuration and damping values of the viscous damper, are studied and compared. As an application example, numerical analyses are conducted to study the dynamic performance of a 39-story office tower installed with toggle brace dampers constructed on soft soil in a reclaimed area, under a combined effect of the vortex shedding of an adjacent existing 52-story building and earthquakes. The results show that viscous dampers with a motion amplification system using a properly designed toggle brace device proved to be an effective solution to alleviate the external excitations.展开更多
A meshless numerical simulation method, the moving-particle semi-implicit method （MPS） is presented in this paper to study the sloshing phenomenon in ocean and naval engineering. As a meshless method, MPS uses parti...A meshless numerical simulation method, the moving-particle semi-implicit method （MPS） is presented in this paper to study the sloshing phenomenon in ocean and naval engineering. As a meshless method, MPS uses particles to replace the mesh in traditional methods, the governing equations are discretized by virtue of the relationship of particles, and the Poisson equation of pressure is solved by incomplete Cholesky conjugate gradient method （ICCG）, the free surface is tracked by the change of numerical density. A numerical experiment of viscous liquid sloshing tank was presented and compared with the result got by the difference method with the VOF, and an additional modification step was added to make the simulation more stable. The results show that the MPS method is suitable for the simulation of viscous liquid sloshing, with the advantage in arranging the particles easily, especially on some complex curved surface.展开更多
A mass transfer model for devolatilization process of highly viscous media in rotating packed bed(RPB) was developed based on penetration theory and mass conservation.Before establishing the model,some mass transfer e...A mass transfer model for devolatilization process of highly viscous media in rotating packed bed(RPB) was developed based on penetration theory and mass conservation.Before establishing the model,some mass transfer experiments of thin film were conducted in a designed diffusion cell including vacuum and feeding system. In this study,acetone was used as the volatile organic compound(VOC) and syrup as the highly viscous media.The thickness of thin film was changed by using different liquid distributor.It was found that bubbling played an important role in the devolatilization.The correlation of diffusion coefficient of acetone in highly viscous dilute solution was proposed.The relative error between predicted and experimental data was within the range of ± 30% for diffusion coefficient of acetone in syrup.A comparison of experimental data of RPB with model indicated that the relative error was within ± 30% for efficiency of acetone removal.展开更多
The rising behavior of single bubbles has been investigated in six systems with different viscosity and Morton number(Mo) from 3.21×10-11 to 163. Bubbles with maximum equivalent diameter of up to 16 mm were inves...The rising behavior of single bubbles has been investigated in six systems with different viscosity and Morton number(Mo) from 3.21×10-11 to 163. Bubbles with maximum equivalent diameter of up to 16 mm were investigated. The bubble Reynolds number(Re) ranged from 0.02 to 1200 covering 3 regimes in which two func-tions are obtained relating the drag coefficient,CD,with Re and Mo. It has been found that in the high Reynolds number regime the drag coefficient increases until the Reynolds number of about 1200. The classic expression of Jamialahmadi(1994) is improved and extended to high viscosity liquids. A new relationship for the aspect ratio of deformed bubbles in terms of Re,the Etvs number and Mo,applicable to a wide range of system properties,espe-cially in high viscosity liquids,is also suggested.展开更多
The static dent resistance performance of the aluminum alloy double-curved panel formed using viscous pressure forming (VPF)was studied by finite element analysis,which mainly considers the forming process conditions....The static dent resistance performance of the aluminum alloy double-curved panel formed using viscous pressure forming (VPF)was studied by finite element analysis,which mainly considers the forming process conditions.The whole simulation consisting of three stages,i.e.,forming,spring-back and static dent resistance,was carried out continuously using the finite element code ANSYS.The influence of blank holder pressure(BHP)and the drawbead on the stiffness and the static dent resistance of the panels formed using VPF was analyzed.The results show that the adequate setting of the drawbead can increase the plastic deformation of the double-curved panel,which is beneficial to the initial stiffness and the static dent resistance.There is an optimum BHP range for the stiffness and the static dent resistance.展开更多
Two-dimensional unsteady incompressible viscous flow around a rolling cylinder with ship-like section is numerically simulated by employing the computational scheme previously developed by the authors, in which the co...Two-dimensional unsteady incompressible viscous flow around a rolling cylinder with ship-like section is numerically simulated by employing the computational scheme previously developed by the authors, in which the continuity and momentum equations are satisfied simultaneously at each time step for oscillating flow. The numerical results show that the motion of vortices around a rolling ship hull is cyclical. It is found that the location of the vortices is very similar to the existing experimental result. Using these simulation results, we can calculate the roll damping of ships including viscous effects.展开更多
The objective of this paper is to present and to validate a new hybrid coupling （HC） algorithm for modeling of fluid-structure interaction （FSI） in incompressible, viscous flows. The HC algorithm is able to avoid ...The objective of this paper is to present and to validate a new hybrid coupling （HC） algorithm for modeling of fluid-structure interaction （FSI） in incompressible, viscous flows. The HC algorithm is able to avoid numerical instability issues associated with artificial added mass effects, which are often encountered by standard loosely coupled （LC） and tightly coupled （TC） algorithms, when modeling the FSI response of flexible structures in incompressible flow. The artificial added mass effect is caused by the lag in exchange of interfacial displacements and forces between the fluid and solid solvers in partitioned algorithms. The artificial added mass effect is much more prominent for light/flexible struc- tures moving in water, because the fluid forces are in the same order of magnitude as the solid forces, and because the speed at which numerical errors propagate in an incom- pressible fluid. The new HC algorithm avoids numerical instability issues associated with artificial added mass effects by embedding Theodorsen＇s analytical approximation of the hydroelastic forces in the solution process to obtain better initial estimates of the displacements. Details of the new HC algorithm are presented. Numerical validation studies are shown for the forced pitching response of a steel and a plastic hydrofoil. The results show that the HC algorithm is able to converge faster, and is able to avoid numerical insta- bility issues, compared to standard LC and TC algorithms, when modeling the transient FSI response of a plastic hydrofoil. Although the HC algorithm is only demonstrated for a NACA0009 hydrofoil subject to pure pitching motion, the method can be easily extended to model general 3-D FSI response and stability of complex, flexible structures in turbulent, incompressible, multiphase flows.展开更多
Debris flow drainage canal is one of the most widely used engineering measures to prevent and manage debris flow hazards.The shape and the sizes of the cross-section are important parameters when design debris flow dr...Debris flow drainage canal is one of the most widely used engineering measures to prevent and manage debris flow hazards.The shape and the sizes of the cross-section are important parameters when design debris flow drainage canal.Therefore,how to design the appropriate shape and sizes of the cross-section so that the drainage canal can have the optimal drainage capacity is very important and few researched at home and abroad.This study was conducted to analyze the hydraulic condition of a Trapezoid-V shaped drainage canal and optimize its cross-section.By assuming characteristic sizes of the cross-section,the paper deduced the configuration parameter of the cross-section of a Trapezoid-V shaped debris flow drainage canal.By theory analysis,it indicates that the optimal configuration parameter is only related to the side slope coefficient and the bottom transverse slope coefficient.For this study,the Heishui Gully,a first-order tributary of the lower Jinsha River,was used as an example to design the optimal cross-section of the drainage canal of debris flow.展开更多
基金supports for this project from State Key Laboratory of Chemical Safety(SKLCS–2024001)are gratefully acknowledged。
文摘Bubble breakup at T-junction microchannels is the basis for the numbering-up of gas−liquid two-phase flow in parallelized microchannels. This article presents the bubble breakup in viscous liquids at a microfluidic T-junction. Nitrogen is used as the gas phase, and glycerol-water mixtures with different mass concentration of glycerol as the liquid phase. The evolution of the gas−liquid interface during bubble breakup at the microfluidic T-junction is explored. The thinning of the bubble neck includes the squeezing stage and the rapid pinch-off stage. In the squeezing stage, the power law relation is found between the minimum width of the bubble neck and the time, and the values of exponents α1 and α2 are influenced by the viscous force. The values of pre-factors m_(1) and m_(2) are negatively correlated with the capillary number. In the rapid pinch-off stage, the thinning of the bubble neck is predominated by the surface tension, and the minimum width of the bubble neck can be scaled with the remaining time as power-law. The propagation of the bubble tip can be characterized by the power law between the movement distance and the time, with decreasing exponent as increased liquid viscosity.
文摘Maximizing the efficiency of thermal engineering equipment involves minimizing entropy generation,which arises from irreversible processes.This study examines thermal transport and entropy generation in viscous flow over a radially stretching disk,incorporating the effects of magnetohydrodynamics(MHD),viscous dissipation,Joule heating,and radiation.Similarity transformations are used to obtain dimensionless nonlinear ordinary differential equations(ODEs)from the governing coupled partial differential equations(PDEs).The converted equations are then solved by using the BVP4C solver in MATLAB.To validate the findings,the results are compared with previously published studies under fixed parameter conditions,demonstrating strong agreement.Various key parameters are analyzed graphically to assess their impact on velocity and temperature distributions.Additionally,Bejan number and entropy generation variations are presented for different physical parameters.The injection parameter(S<0)increases the heat transfer rate,while the suction parameter(S>0)reduces it,exhibiting similar effects on fluid velocity.The magnetic parameter(M)effectively decreases entropy generation within the range of approximately 0≤η≤0.6.Beyond this interval,its influence diminishes as entropy generation values converge,with similar trends observed for the Bejan number.Furthermore,increased thermal radiation intensity is identified as a critical factor in enhancing entropy generation and the Bejan number.
基金Project(52276068)supported by the National Natural Science Foundation of China。
文摘This study examines the intricate occurrences of thermal and solutal Marangoni convection in three-layered flows of viscous fluids,with a particular emphasis on their relevance to renewable energy systems.This research examines the flow of a three-layered viscous fluid,considering the combined influence of heat and solutal buoyancy driven Rayleigh-Bénard convection,as well as thermal and solutal Marangoni convection.The homotopy perturbation method is used to examine and simulate complex fluid flow and transport phenomena,providing important understanding of the fundamental physics and assisting in the optimization of various battery configurations.The inquiry examines the primary elements that influence Marangoni convection and its impact on battery performance,providing insights on possible enhancements in energy storage devices.The findings indicate that the velocity profiles shown graphically exhibit a prominent core zone characterized by the maximum speed,which progressively decreases as it approaches the walls of the channel.This study enhances our comprehension of fluid dynamics and the transmission of heat and mass in intricate systems,which has substantial ramifications for the advancement of sustainable energy solutions.
基金financially supported by the Key Research and Development Program of Hubei Province(Nos.2022BCA077 and 2022BCA082).
文摘Styrene-butadiene-styrene(SBS)modified asphalt(SA)has long found effective applications in road construction materials.When combined with fillers,SBS-modified asphalt has demonstrated promising resistance to fatigue cracking caused by temperature fluctuations and aging.In this study,molybdenum disulfide(MoS_(2))and polyphosphoric acid(PPA)were ground in naphthenic oil(NO)and subjected to mechanical activation to create PPAmodified MoS_(2),referred to as OMS-PPA.By blending various ratios of OMS-PPA with SBS-modified asphalt,composite-modified asphalts were successfully developed to enhance their overall properties.To assess the mechanical characteristics and stability of these modified asphalts,various methods were employed,including penetration factor,flow activation energy,fluorescence microscopy,and dynamic shear rheology.Additionally,the short-term aging performance was evaluated using Fourier transform infrared(FTIR)spectroscopy and nanoindentation tests.The results revealed a 3.7%decrease in the penetration-temperature coefficient for SAOMS compared to SA,while 1-SA-OMS-PPA showed an even greater reduction of 7.1%.Furthermore,after short-term aging,carboxyl group generation in SA increased by 5.93%,while SA-OMS exhibited a smaller rise of 1.36%,and 1-SA-OMS-PPA saw an increase of just 0.93%.The study also highlighted significant improvements in the hardness of these materials.The hardness change ratio for SA-OMS decreased by 43.08%,while the ratio for 1-SA-OMS-PPA saw a notable reduction of 65.16% compared to unmodified SA.These findings suggest that OMS-PPA contributed to improvements in temperature sensitivity,particle dispersibility,and resistance to shortterm aging in asphalts.The results hold significant promise for the future development of advanced asphalt-based materials with potential high-value applications in flexible pavements for highways.
基金supported by the National Key Research and Development Program of China(2019YFA0705800)the National Natural Science Foundation of China(52030001)the Science&Technology Commission of Shanghai Municipality(20dz1207600).
文摘Drying operations are of grave importance to realize the reduction and utilization of sewage sludge resources,but the conventional thermal evaporation drying(TED)technology presents challenges due to the need for a large amount of thermal energy to conquer the phase-change latent heat of moisture.Herein,we report a non-phase change technology based on particle high-speed self-rotation in a cyclone for fast,low-temperature drying of viscous sludge with high-moisture contents.Dispersed phase medium(DPM)is introduced into the cyclone self-rotation drying(CSRD)reactor to enhance the dispersion of the viscous sludge.The effects of carrier gas temperature,feeding rate,size,and proportion of DPM particles in the drying process are systematically examined.Under optimal operating conditions,the weighted content of moisture in the viscous sludge could be reduced from 80%to 15.01%in less than 5 s,achieving a high drying efficiency of 95.79%.Theoretical calculations also reveal that 89.26%of the moisture is removed through non-phase change pathway,contributing to a 522-fold increase in the drying rate of CSRD compared to TED technology.This investigation presents a sustainable effective approach for high moisture viscous sludge treatment with low energy consumption and carbon emissions.
基金supported by the Research and Innovation Fund for Graduate Students of Southwest Petroleum University(No.2022KYCX027)supported by the National Natural Science Foundation for Youth Grant(No.41902157).
文摘Studying immiscible fluid displacement patterns can provide a better understanding of displacement processes within heterogeneous porous media,thereby helping improving oil recovery and optimizing geological CO_(2) sequestration.As the injection rate of water displacing oil increases and the displacement pattern transits from capillary fingering to viscous fingering,there is a broad crossover zone between the two that can adversely affect the oil displacement efficiency.While previous studies have utilized phase diagrams to investigate the influence of the viscosity ratio and wettability of the crossover zone,fewer have studied the impact of rock heterogeneity.In this study,we created pore network models with varying degrees of heterogeneity to simulate water flooding at different injection rates.Our model quantifies capillary and viscous fingering characteristics while investigating porous media heterogeneity's role in the crossover zone.Analysis of simulation results reveals that a higher characteristic front flow rate within the crossover zone leads to earlier breakthrough and reduced displacement efficiency.Increased heterogeneity in the porous media raises injection-site pressure,lowers water saturation,and elevates the characteristic front flow rate,thereby expanding the extent of crossover zone.
基金supported by the NSFC(12271122)the Fundamental Research Funds for the Central Universities.Han’s research was supported by the Fundamental Research Funds for the Central Universities(3072023GIP2401).
文摘In this paper,we consider the initial boundary value problem for the 2-D hyperbolic viscous Cahn-Hilliard equation.Firstly,we prove the existence and uniqueness of the local solution by the Galerkin method and contraction mapping principle.Then,using the potential well theory,we study the global well-posedness of the solution with initial data at different levels of initial energy,i.e.,subcritical initial energy,critical initial energy and arbitrary positive initial energy.For subcritical initial energy,we prove the global existence,asymptotic behavior and finite time blowup of the solution.Moreover,we extend these results to the critical initial energy using the scaling technique.For arbitrary positive initial energy,including the sup-critical initial energy,we obtain the sufficient conditions for finite time blow-up of the solution.As a further study for estimating the blowup time,we give a unified expression of the lower bound of blowup time for all three initial energy levels and estimate the upper bound of blowup time for subcritical and critical initial energy.
基金Project(51575364)supported by the National Natural Science Foundation of ChinaProject(2013024014)supported by the Natural Foundation of Liaoning Province,China
文摘Based on the bulging principle of different ellipticity dies, the methyl vinyl silicone rubber with excellent thermal stability and heat transfer performance was chosen as the viscous medium. The finite element analysis and experiments of viscous warm pressure bulging （VWPB） of AZ31B magnesium alloy were conducted to analyze the influence of different ellipticity dies on the formability of AZ31B magnesium alloy. At the same time, based on the grid strain rule, the forming limit diagram （FLD） of VWPB of AZ31B magnesium alloy was obtained through measuring the strain of bulging specimens. The results showed that at the temperature range of viscous medium thermal stability, the viscous medium can fit the geometry variation of sheet and generate non-uniform pressure field, and as the die ellipticity increases, the difference value of non-uniform pressure reduces. Meanwhile, according to the FLD, the relationship between part complexity and ultimate deformation was investigated.
文摘Aim To get the analytical for laminar viscous flow in the gap of two parallel rotating disks. Methods By estimating the order of magnitude of each term in the Navier-Stokes equations to drop small terms and achieve the required simplified differential equations, and by integrating the equations to obtain the solution for theflow between two rotary disks. Results Parameters related to the laminar viscous flow in the gap between two parallel rotary disks, such as the velocity, the pressure, the flowrate, the force, the shearing stress, the torque and the power derived. Conclusion The result provides a theoretical basis and an effective method for the designs of the devices connected with the laminar viscous flow in the gap between two parallel rotary disks.
基金supported by the National Natural Science Foundation of China (No. 41201011)the Key Research Program of the Chinese Academy of Sciences (CAS) (No. KZZD-EW-05-01)the Youth Talent Team Program of Institute of Mountain Hazards and Environment, CAS (No. SDSQB-2013-01)
文摘The mean velocity estimation of debris flows, especially viscous debris flows, is an important part in the debris flow dynamics research and in the design of control structures. In this study, theoretical equations for computing debris flow velocity with the one-phase flow assumption were reviewed and used to analyze field data of viscous debris flows. Results show that the viscous debris flow is diffficult to be classified as a Newtonian laminar flow, a Newtonian turbulent flow, a Bingham fluid, or a dilatant fluid in the strict sense. However, we can establish empirical formulas to compute its mean velocity following equations for Newtonian turbulent flows, because most viscous debris flows are tur- bulent. Factors that potentially influence debris flow velocity were chosen according to two-phase flow theories. Through correlation analysis and data fitting, two empirical formulas were proposed. In the first one, velocity is expressed as a function of clay content, flow depth and channel slope. In the second one, a coefficient representing the grain size nonuniformity is used instead of clay content. Both formulas can give reasonable estimate of the mean velocity of the viscous debris flow.
基金Project (50975263) supported by the National Natural Science Foundation of ChinaProject (2010081015) supported by International Cooperation Project of Shanxi Province, China+1 种基金 Project (2010-78) supported by the Scholarship Council in Shanxi province, ChinaProject (2010420120005) supported by Doctoral Fund of Ministry of Education of China
文摘A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions according to Reynolds number.In the far-wall region,the thermal melt flow was calculated as Newtonian flow.In the near-wall region,the thermal melt flow was calculated as non-Newtonian flow.It was proved that the new algorithm based on the projection method with the implicit technique was correct through nonparametric statistics method and experiment.The simulation results show that the new algorithm based on the projection method with the implicit technique calculates more quickly than the solution algorithm-volume of fluid method using the explicit difference method.
基金Supported by the National Natural Science Foundation of China(10372043,11172134)the Fundingof Jiangsu Innovation Program for Graduate Education(CXZZ11-0192)~~
文摘Gridless method is developed for unsteady viscous flows involving moving boundaries. The point distri- bution of gridless method is implemented in an isotropic or anisotropic way according to the features of viscous flows. In the area far away from the body, the traditional cloud of isotropic points is used, while in the adjacent area, the cloud of anisotropic points is distributed. In this way, the point spacing normal to the wall can be small enough for simulating the boundary layer, and meanwhile, the total number of points in the computational do- main can be controlled due to large spacing in other tangential direction through the anisotropic way. A fast mov- ing technique of clouds of points at each time-step is presented based on the attenuation law of disturbed motion for unsteady flows involving moving boundaries. In the mentioned cloud of points, a uniform weighted least- square curve fit method is utilized to discretize the spatial derivatives of the Navier-Stokes equations. The pro- posed gridless method, coupled with a dual time-stepping method and the Spalart-Allmaras turbulence model, is implemented for the Navier-Stokes equations. The computational results of unsteady viscous flows around a NLR7301 airfoil with an oscillating flap and a pitching NACA0012 airfoil are presented in a good agreement with the available experimental data.
文摘After nearly a decade of application and investigation, a motion amplification device with viscous dampers for energy dissipation has been recognized as an effective solution to mitigate wind or seismic excitation, especially for stiff structural systems. As a result of compensation of amplified motion, it has been proved that the efficiency of viscous damper largely depends on the motion amplification device configuration, particularly for device stiflhess. In this paper, a ＂scissor-jack＂ type of motion amplification device, called a ＂toggle brace damper＂ system, is studied. It is demonstrated that the efficiency of such a device reflected by its amplification factor is not merely a function of its geometric configuration, but is highly dependent on the support elements＇ stiffness as well, similar to the mechanism of a leverage arm. Accordingly, a mathematical model in terms of complex modulus of the viscous damper with consideration of the support brace＇s stiffness is established. The results indicate that the efficiency of the motion amplification device with viscous dampers significantly depends on the stiffness of the support elements. Other parameters, such as toggle brace configuration and damping values of the viscous damper, are studied and compared. As an application example, numerical analyses are conducted to study the dynamic performance of a 39-story office tower installed with toggle brace dampers constructed on soft soil in a reclaimed area, under a combined effect of the vortex shedding of an adjacent existing 52-story building and earthquakes. The results show that viscous dampers with a motion amplification system using a properly designed toggle brace device proved to be an effective solution to alleviate the external excitations.
基金the National Natural Science Foundation under Grant No.50579035
文摘A meshless numerical simulation method, the moving-particle semi-implicit method （MPS） is presented in this paper to study the sloshing phenomenon in ocean and naval engineering. As a meshless method, MPS uses particles to replace the mesh in traditional methods, the governing equations are discretized by virtue of the relationship of particles, and the Poisson equation of pressure is solved by incomplete Cholesky conjugate gradient method （ICCG）, the free surface is tracked by the change of numerical density. A numerical experiment of viscous liquid sloshing tank was presented and compared with the result got by the difference method with the VOF, and an additional modification step was added to make the simulation more stable. The results show that the MPS method is suitable for the simulation of viscous liquid sloshing, with the advantage in arranging the particles easily, especially on some complex curved surface.
基金Supported by the National Natural Science Foundation of China（20821004 20990221） the National High Technology Research and Development Program of China（2006AA030202）+1 种基金 the Program for New Century Excellent Talents in University of China（NCET-07-0053） the National Basic Research Program of China（2009CB219903）
文摘A mass transfer model for devolatilization process of highly viscous media in rotating packed bed(RPB) was developed based on penetration theory and mass conservation.Before establishing the model,some mass transfer experiments of thin film were conducted in a designed diffusion cell including vacuum and feeding system. In this study,acetone was used as the volatile organic compound(VOC) and syrup as the highly viscous media.The thickness of thin film was changed by using different liquid distributor.It was found that bubbling played an important role in the devolatilization.The correlation of diffusion coefficient of acetone in highly viscous dilute solution was proposed.The relative error between predicted and experimental data was within the range of ± 30% for diffusion coefficient of acetone in syrup.A comparison of experimental data of RPB with model indicated that the relative error was within ± 30% for efficiency of acetone removal.
基金Supported by the National Natural Science Foundation of China （20821004 20990224） the National Basic Research Program of China （2007CB714300）
文摘The rising behavior of single bubbles has been investigated in six systems with different viscosity and Morton number(Mo) from 3.21×10-11 to 163. Bubbles with maximum equivalent diameter of up to 16 mm were investigated. The bubble Reynolds number(Re) ranged from 0.02 to 1200 covering 3 regimes in which two func-tions are obtained relating the drag coefficient,CD,with Re and Mo. It has been found that in the high Reynolds number regime the drag coefficient increases until the Reynolds number of about 1200. The classic expression of Jamialahmadi(1994) is improved and extended to high viscosity liquids. A new relationship for the aspect ratio of deformed bubbles in terms of Re,the Etvs number and Mo,applicable to a wide range of system properties,espe-cially in high viscosity liquids,is also suggested.
文摘The static dent resistance performance of the aluminum alloy double-curved panel formed using viscous pressure forming (VPF)was studied by finite element analysis,which mainly considers the forming process conditions.The whole simulation consisting of three stages,i.e.,forming,spring-back and static dent resistance,was carried out continuously using the finite element code ANSYS.The influence of blank holder pressure(BHP)and the drawbead on the stiffness and the static dent resistance of the panels formed using VPF was analyzed.The results show that the adequate setting of the drawbead can increase the plastic deformation of the double-curved panel,which is beneficial to the initial stiffness and the static dent resistance.There is an optimum BHP range for the stiffness and the static dent resistance.
基金This project is supported by Fok Ying Tung Education Foundation and National Natural Science Foundation of China
文摘Two-dimensional unsteady incompressible viscous flow around a rolling cylinder with ship-like section is numerically simulated by employing the computational scheme previously developed by the authors, in which the continuity and momentum equations are satisfied simultaneously at each time step for oscillating flow. The numerical results show that the motion of vortices around a rolling ship hull is cyclical. It is found that the location of the vortices is very similar to the existing experimental result. Using these simulation results, we can calculate the roll damping of ships including viscous effects.
基金the financial support provided by the Office of Naval Research(ONR) through grant number N00014-09-1-1204 (managed by Dr. Ki-Han Kim)supported in part by the National Research Foundation of Korea (NRF)grant funded by the Korea government (MEST) through the GCRC-SOP Grant No. 2012-0004783
文摘The objective of this paper is to present and to validate a new hybrid coupling （HC） algorithm for modeling of fluid-structure interaction （FSI） in incompressible, viscous flows. The HC algorithm is able to avoid numerical instability issues associated with artificial added mass effects, which are often encountered by standard loosely coupled （LC） and tightly coupled （TC） algorithms, when modeling the FSI response of flexible structures in incompressible flow. The artificial added mass effect is caused by the lag in exchange of interfacial displacements and forces between the fluid and solid solvers in partitioned algorithms. The artificial added mass effect is much more prominent for light/flexible struc- tures moving in water, because the fluid forces are in the same order of magnitude as the solid forces, and because the speed at which numerical errors propagate in an incom- pressible fluid. The new HC algorithm avoids numerical instability issues associated with artificial added mass effects by embedding Theodorsen＇s analytical approximation of the hydroelastic forces in the solution process to obtain better initial estimates of the displacements. Details of the new HC algorithm are presented. Numerical validation studies are shown for the forced pitching response of a steel and a plastic hydrofoil. The results show that the HC algorithm is able to converge faster, and is able to avoid numerical insta- bility issues, compared to standard LC and TC algorithms, when modeling the transient FSI response of a plastic hydrofoil. Although the HC algorithm is only demonstrated for a NACA0009 hydrofoil subject to pure pitching motion, the method can be easily extended to model general 3-D FSI response and stability of complex, flexible structures in turbulent, incompressible, multiphase flows.
基金supported by the National Science and Technology Supporting Plan(Grant No.2009BAK56B05)Key Project of Chinese National Programs for Fundamental Research and Development(973 Program)(Grant No.2008CB425803)
文摘Debris flow drainage canal is one of the most widely used engineering measures to prevent and manage debris flow hazards.The shape and the sizes of the cross-section are important parameters when design debris flow drainage canal.Therefore,how to design the appropriate shape and sizes of the cross-section so that the drainage canal can have the optimal drainage capacity is very important and few researched at home and abroad.This study was conducted to analyze the hydraulic condition of a Trapezoid-V shaped drainage canal and optimize its cross-section.By assuming characteristic sizes of the cross-section,the paper deduced the configuration parameter of the cross-section of a Trapezoid-V shaped debris flow drainage canal.By theory analysis,it indicates that the optimal configuration parameter is only related to the side slope coefficient and the bottom transverse slope coefficient.For this study,the Heishui Gully,a first-order tributary of the lower Jinsha River,was used as an example to design the optimal cross-section of the drainage canal of debris flow.
