The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) metho...The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) method to address these limitations. In the vLEC method, the waverider is directly designed from the preassigned leading edge and the variable shock angle distribution based on the Leading-Edge Cone (LEC) concept. Since the vLEC method is an approximate method, two test waveriders are designed and evaluated using numerical simulations to validate the shock design accuracy and the effectiveness of the vLEC method. The results show that the shocks of the test waveriders coincide well with the preassigned positions. Furthermore, four specifically designed application cases are conducted to analyze the performance benefits of the vLEC waveriders. The results of these cases indicate that, due to their variable shock angle distributions, the vLEC waveriders exhibit higher lift-to-drag ratios and better longitudinal static stability than conventional waveriders. Additionally, the vLEC waveriders demonstrate superior volumetric capacities near the symmetry plane, albeit with a minor decrease in volumetric efficiency.展开更多
A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technolog...A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technology of stream tracing and shock cutting.Comparison between the newly designed inlet and a typical sidewall compression inlet is given.The design Mach number and entrance shape of this new inlet are chosen according to the sidewall compression inlet.Numerical results show that most of the performance parameters of the internal waverider inlet are a bit higher than the sidewall inlet,such as the flow capture coefficient,total pressure recovery and the kinetic efficiency.The performances of these two inlets at off-design points are compared.The internal waverider inlet can capture more than 91% of incoming flow under all simulated conditions.Results show that internal waverider inlet using 3-D compression and high flow capture coefficient is a kind of fixed-geometry inlet with better performance.展开更多
A method based on the computational fluid dynamics （CFD） is presented for a flexible waverider＇s design. The generating bodies of this method could be any cones. In addition, either the leading edge or the profile ...A method based on the computational fluid dynamics （CFD） is presented for a flexible waverider＇s design. The generating bodies of this method could be any cones. In addition, either the leading edge or the profile of the scramjet＇s inlet is used as the waverider＇s definition curve, parameterized by the quadric function, the sigmoid function or the B-spline function. Furthermore, several numerical examples are carried out to validate the method and the relevant codes. The CFD results of the configurations show that all the designs are successful. Moreover, primary suggestions are proposed for practical design by comparing the geometrical and aerodynamic performances of the conederived waveriders at Mach 6.展开更多
A design method based on tip to tail streamline tracing and osculating inward cone methods is discussed for designing the integrated Osculating Inward Cone Waverider Inlet（OICWI）. A practical geometrical constrained...A design method based on tip to tail streamline tracing and osculating inward cone methods is discussed for designing the integrated Osculating Inward Cone Waverider Inlet（OICWI）. A practical geometrical constrained experimental model of OICWI is designed based on the validated design method. It has a total contraction ratio of 4.61 and inner contraction ratio is 2.0. Wind-tunnel tests have been conducted for the OICWI model at free stream Mach number（Ma） of 4.0, 3.5 and 3.0 respectively. The experimental results show that the OICWI has high flow capture ratio and compression abilities. It can self-start at Ma= 3.5 and 4.0 and its flow capture ratio is 0.73 at Ma= 4.0, and Angle of Attack（AOA） 0°. The research results show that the OICWI has advantages of inward cone waverider and streamline tracing inlet. Present OICWI is a novel approach for waverider inlet integration studies and it will promote the use of waverider inlet integration configuration in the studies of airbreathing hypersonic vehicles.展开更多
Intensive studies have been carried out on generations of waverider geometry and hypersonic inlet geometry. However, integration efforts of waverider and related air-intake system are restricted majorly around the X43...Intensive studies have been carried out on generations of waverider geometry and hypersonic inlet geometry. However, integration efforts of waverider and related air-intake system are restricted majorly around the X43A-like or conical flow field induced configuration, which adopts mainly the two-dimensional air-breathing technology and limits the judicious visions of developing new aerodynamic profiles for hypersonic designers. A novel design approach for integrating the inward turning inlet with the traditional parameterized waverider is proposed. The proposed method is an alternative means to produce a compatible configuration by linking the off-the-shelf results on both traditional waverider techniques and inward turning inlet techniques. A series of geometry generations and optimization solutions is proposed to enhance the lift-to-drag ratio. A quantitative but efficient aerodynamic performance evaluation approach （the hypersonic flow panel method） with lower computational cost is employed to play the role of objective function for opti- mization purpose. The produced geometry compatibility with a computational fluid dynamics （CFD） solver is also verified for detailed flow field investigation. Optimization results and other numerical validations are obtained for the feasibility demonstration of the proposed method.展开更多
When considering the practical engineering application of a waverider,the on-design and off-design aerodynamic characteristics of the design conditions,especially the lift-to-drag ratio and the stability,deserve atten...When considering the practical engineering application of a waverider,the on-design and off-design aerodynamic characteristics of the design conditions,especially the lift-to-drag ratio and the stability,deserve attention.According to recently studies,the planform and rear sight shape of a waverider are closely related to the above aerodynamic performance.Thus,the planform leading-edge profile curve used to design the planform shape of a vehicle is applied to designing an osculating cone waverider.Two key parameters concerned in planform and rear sight shape,namely the plan view sweep angle of the leading edge and the dihedral angle of the underside are introduced to the waverider design process.Each parameter is inserted in the control curve equation.Especially,a parameterization scheme is put forward for the free adjustment of the sweep angle along the leading edge.Finally,three examples are generated for verification and investigation.After the verification process based on the inviscid flow field of one case,the influences of the sweep and dihedral angles on the lift-to-drag ratio and the lateral static stability are evaluated,and meaningful results are obtained.Based on these results,we can conclude that,considering the maximum lift-to-drag ratio,the sweep angle plays a role on the lift-to-drag ratio only at subsonic and trans/supersonic speed as a negligible effect is observed at hypersonic speeds,whereas the dihedral angle is seem to produce a relevant difference at hypersonic speeds.Considering the lateral static stability,the dihedral angles have more influence on the waverider than the sweep angles.展开更多
Developing the waverider based hypersonic vehicles is an inverse design process in which shape is developed from a known flow field by tracing of streamlines to form a stream surface. The flow field can be based on a ...Developing the waverider based hypersonic vehicles is an inverse design process in which shape is developed from a known flow field by tracing of streamlines to form a stream surface. The flow field can be based on a solution of Taylor Maccoll equation for a specified shock or cone angle. This Paper discusses the development of waverider shapes for hypersonic reentry vehicles.展开更多
An experiment of a hypersonic vehicle configuration was conducted. The pressure difference of forbody precornpress surface is small. Pressure difference of three monitor points are 25.2%, 20. 5% and 17.29% respectivel...An experiment of a hypersonic vehicle configuration was conducted. The pressure difference of forbody precornpress surface is small. Pressure difference of three monitor points are 25.2%, 20. 5% and 17.29% respectively in the design condition. It indicates that there is crosswise flow in forebody boundary layer. Pressure difference at Ma = 6. 971 is lower than those of two other Mach number conditions. It indicates that the tested configuration has good aerodynamic performance in high Maeh number. Angle of attack has no great influence on the pressure difference. In almost all the angle of attack conditions, the pressure difference at Ma =6. 971 is slightly smaller than that in Ma =5. 993. The difference in the third precompress surface is slightly smaller than those in two others.展开更多
基金supported by grants from the National Natural Science Foundation of China(No.U20B2006)the Guangdong Basic and Applied Basic Research Foundation(No.2022A1515110145)Young Elite Scientists Sponsorship Program by China Association for Science and Technology(No.2022QNRC001).
文摘The optimization of the waverider is constrained by the reversely designed leading edge and the constant shock angle distribution. This paper proposes a design method called the variable Leading-Edge Cone (vLEC) method to address these limitations. In the vLEC method, the waverider is directly designed from the preassigned leading edge and the variable shock angle distribution based on the Leading-Edge Cone (LEC) concept. Since the vLEC method is an approximate method, two test waveriders are designed and evaluated using numerical simulations to validate the shock design accuracy and the effectiveness of the vLEC method. The results show that the shocks of the test waveriders coincide well with the preassigned positions. Furthermore, four specifically designed application cases are conducted to analyze the performance benefits of the vLEC waveriders. The results of these cases indicate that, due to their variable shock angle distributions, the vLEC waveriders exhibit higher lift-to-drag ratios and better longitudinal static stability than conventional waveriders. Additionally, the vLEC waveriders demonstrate superior volumetric capacities near the symmetry plane, albeit with a minor decrease in volumetric efficiency.
文摘A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technology of stream tracing and shock cutting.Comparison between the newly designed inlet and a typical sidewall compression inlet is given.The design Mach number and entrance shape of this new inlet are chosen according to the sidewall compression inlet.Numerical results show that most of the performance parameters of the internal waverider inlet are a bit higher than the sidewall inlet,such as the flow capture coefficient,total pressure recovery and the kinetic efficiency.The performances of these two inlets at off-design points are compared.The internal waverider inlet can capture more than 91% of incoming flow under all simulated conditions.Results show that internal waverider inlet using 3-D compression and high flow capture coefficient is a kind of fixed-geometry inlet with better performance.
基金the National Natural Science Foundation of China （10502053, 10372106 , 10402043）, K. C. Wong Education Foundation of Hong Kongthe Key Laboratory of High Temperature Gas Dynamics of Chinese Academy of Sciences the State Key Laboratory of Structural Analysis for Industrial Equipment of Dalian University of Technology.
文摘A method based on the computational fluid dynamics （CFD） is presented for a flexible waverider＇s design. The generating bodies of this method could be any cones. In addition, either the leading edge or the profile of the scramjet＇s inlet is used as the waverider＇s definition curve, parameterized by the quadric function, the sigmoid function or the B-spline function. Furthermore, several numerical examples are carried out to validate the method and the relevant codes. The CFD results of the configurations show that all the designs are successful. Moreover, primary suggestions are proposed for practical design by comparing the geometrical and aerodynamic performances of the conederived waveriders at Mach 6.
基金supported by the National Natural Science Foundation of China (Nos. 51376192 and 91216303)
文摘A design method based on tip to tail streamline tracing and osculating inward cone methods is discussed for designing the integrated Osculating Inward Cone Waverider Inlet（OICWI）. A practical geometrical constrained experimental model of OICWI is designed based on the validated design method. It has a total contraction ratio of 4.61 and inner contraction ratio is 2.0. Wind-tunnel tests have been conducted for the OICWI model at free stream Mach number（Ma） of 4.0, 3.5 and 3.0 respectively. The experimental results show that the OICWI has high flow capture ratio and compression abilities. It can self-start at Ma= 3.5 and 4.0 and its flow capture ratio is 0.73 at Ma= 4.0, and Angle of Attack（AOA） 0°. The research results show that the OICWI has advantages of inward cone waverider and streamline tracing inlet. Present OICWI is a novel approach for waverider inlet integration studies and it will promote the use of waverider inlet integration configuration in the studies of airbreathing hypersonic vehicles.
基金supported by the National Natural Science Foundation of China (Grant No.61004089)
文摘Intensive studies have been carried out on generations of waverider geometry and hypersonic inlet geometry. However, integration efforts of waverider and related air-intake system are restricted majorly around the X43A-like or conical flow field induced configuration, which adopts mainly the two-dimensional air-breathing technology and limits the judicious visions of developing new aerodynamic profiles for hypersonic designers. A novel design approach for integrating the inward turning inlet with the traditional parameterized waverider is proposed. The proposed method is an alternative means to produce a compatible configuration by linking the off-the-shelf results on both traditional waverider techniques and inward turning inlet techniques. A series of geometry generations and optimization solutions is proposed to enhance the lift-to-drag ratio. A quantitative but efficient aerodynamic performance evaluation approach （the hypersonic flow panel method） with lower computational cost is employed to play the role of objective function for opti- mization purpose. The produced geometry compatibility with a computational fluid dynamics （CFD） solver is also verified for detailed flow field investigation. Optimization results and other numerical validations are obtained for the feasibility demonstration of the proposed method.
基金Project supported by the National Natural Science Foundation of China(No.11702322)the Natural Science Foundation of Hunan Province,China(No.2018JJ3589)。
文摘When considering the practical engineering application of a waverider,the on-design and off-design aerodynamic characteristics of the design conditions,especially the lift-to-drag ratio and the stability,deserve attention.According to recently studies,the planform and rear sight shape of a waverider are closely related to the above aerodynamic performance.Thus,the planform leading-edge profile curve used to design the planform shape of a vehicle is applied to designing an osculating cone waverider.Two key parameters concerned in planform and rear sight shape,namely the plan view sweep angle of the leading edge and the dihedral angle of the underside are introduced to the waverider design process.Each parameter is inserted in the control curve equation.Especially,a parameterization scheme is put forward for the free adjustment of the sweep angle along the leading edge.Finally,three examples are generated for verification and investigation.After the verification process based on the inviscid flow field of one case,the influences of the sweep and dihedral angles on the lift-to-drag ratio and the lateral static stability are evaluated,and meaningful results are obtained.Based on these results,we can conclude that,considering the maximum lift-to-drag ratio,the sweep angle plays a role on the lift-to-drag ratio only at subsonic and trans/supersonic speed as a negligible effect is observed at hypersonic speeds,whereas the dihedral angle is seem to produce a relevant difference at hypersonic speeds.Considering the lateral static stability,the dihedral angles have more influence on the waverider than the sweep angles.
文摘Developing the waverider based hypersonic vehicles is an inverse design process in which shape is developed from a known flow field by tracing of streamlines to form a stream surface. The flow field can be based on a solution of Taylor Maccoll equation for a specified shock or cone angle. This Paper discusses the development of waverider shapes for hypersonic reentry vehicles.
文摘An experiment of a hypersonic vehicle configuration was conducted. The pressure difference of forbody precornpress surface is small. Pressure difference of three monitor points are 25.2%, 20. 5% and 17.29% respectively in the design condition. It indicates that there is crosswise flow in forebody boundary layer. Pressure difference at Ma = 6. 971 is lower than those of two other Mach number conditions. It indicates that the tested configuration has good aerodynamic performance in high Maeh number. Angle of attack has no great influence on the pressure difference. In almost all the angle of attack conditions, the pressure difference at Ma =6. 971 is slightly smaller than that in Ma =5. 993. The difference in the third precompress surface is slightly smaller than those in two others.
