The scroll expander,as the core component of the micro-compressed air energy storage and power generation system,directly affects the output efficiency of the system.Meanwhile,the scroll profile plays a central role i...The scroll expander,as the core component of the micro-compressed air energy storage and power generation system,directly affects the output efficiency of the system.Meanwhile,the scroll profile plays a central role in determining the output performance of the scroll expander.In this study,in order to investigate the output characteristics of a variable cross-section scroll expander,numerical simulation and experimental studies were con-ducted by using Computational Fluid Dynamics(CFD)methods and dynamic mesh techniques.The impact of critical parameters on the output performance of the scroll expander was analyzed through the utilization of the control variable method.It is found that increasing the inlet pressure and temperature within a certain range can improve the output power of the scroll expander.However,the increase in temperature and meshing clearance leads to a decline in the overall output performance of the scroll expander,leading to a decrease in volumetric efficiency by 8.43%and 12.79%,respectively.The experiments demonstrate that under equal inlet pressure conditions,increasing the inlet temperature elevates both the rotational speed and torque output of the scroll expander.Specifically,compared to operating at normal temperatures,the output torque increases by 21.8%under high-temperature conditions.However,the rate of speed and torque variation decreases as a consequence of enlarged meshing clearance,resulting in increased internal leakage and reduction in isentropic efficiency.展开更多
A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigate...A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.展开更多
In order to understand mechanical characters and find out a calculating method for preflex beams used in particular bridge engineering projects, two types of simply supported preflex beams with variable crosssection, ...In order to understand mechanical characters and find out a calculating method for preflex beams used in particular bridge engineering projects, two types of simply supported preflex beams with variable crosssection, preflex beam with alterative web depth and preflex beam with aherative steel flange thickness, are dis- cussed on how to achieve the equivalent moment of inertia and Young＇ s modulus. Additionally, methods of cal- culating the equivalent bending stiffness and post-cracking deflection are proposed. Results of the experiments on 6 beams agree well with the theoretical analysis, which proves the correctness of the proposed formulas.展开更多
This article analyzes the design of a variable-height simply supported steel truss bridge based on an actual project.It includes its basic situation,introduction to variable-height simply supported steel truss bridges...This article analyzes the design of a variable-height simply supported steel truss bridge based on an actual project.It includes its basic situation,introduction to variable-height simply supported steel truss bridges,key design points of such bridges,and finite element analysis of the design effect.The analysis shows that for such bridges,reasonable main structure design and node design are the keys to determining the overall design idea,and through the reasonable application of the finite element analysis method,the design effect can be scientifically determined,providing a reference for the subsequent structural design of such projects.展开更多
Variable stiffness mechanisms(VSMs)are a class of compliant mechanisms that can adjust their intrinsic stiffness,which promises to be beneficial in applications needed to interact with the environment,such as collabor...Variable stiffness mechanisms(VSMs)are a class of compliant mechanisms that can adjust their intrinsic stiffness,which promises to be beneficial in applications needed to interact with the environment,such as collaborative robots,wearable robots,and polishing robots.This paper presents the design and optimization of a novel linear VSM,called cLVSM,to produce linear motion,conversely to the majority of VSMs designed to perform rotary motion.By changing the effective length of specially designed circular beams,the cLVSM is capable of continuous stiffness regulation from a minimum value to almost rigid.Different from the VSMs which need rotation-to-translation converting mechanisms for stiffness regulation,the stiffness of the proposed design is adjusted by directly rotating the beams without the use of additional mechanisms,which contributes to improving the structural compactness,and reducing the energy loss and error in transmission.Moreover,the beam rotation needed to regulate the stiffness is almost perpendicular to the beam deflection force,which helps to reduce the torque needed for stiffness regulation.The stiffness model of the proposed VSM is developed using the screw theory,and the design parameters are optimized using the genetic algorithm.The effectiveness of the mathematical model and the performance of the design are verified by simulation and experiments.展开更多
The behavior of beams with variable stiffness subjected to the action of variable loadings (impulse or harmonic) is analyzed in this paper using the successive approximation method. This successive approximation metho...The behavior of beams with variable stiffness subjected to the action of variable loadings (impulse or harmonic) is analyzed in this paper using the successive approximation method. This successive approximation method is a technique for numerical integration of partial differential equations involving both the space and time, with well-known initial conditions on time and boundary conditions on the space. This technique, although having been applied to beams with constant stiffness, is new for the case of beams with variable stiffness, and it aims to use a quadratic parabola (in time) to approximate the solutions of the differential equations of dynamics. The spatial part is studied using the successive approximation method of the partial differential equations obtained, in order to transform them into a system of time-dependent ordinary differential equations. Thus, the integration algorithm using this technique is established and applied to examples of beams with variable stiffness, under variable loading, and with the different cases of supports chosen in the literature. We have thus calculated the cases of beams with constant or variable rigidity with articulated or embedded supports, subjected to the action of an instantaneous impulse and harmonic loads distributed over its entire length. In order to justify the robustness of the successive approximation method considered in this work, an example of an articulated beam with constant stiffness subjected to a distributed harmonic load was calculated analytically, and the results obtained compared to those found numerically for various steps (spatial h and temporal τ ¯ ) of calculus, and the difference between the values obtained by the two methods was small. For example for ( h=1/8 , τ ¯ =1/ 64 ), the difference between these values is 17%.展开更多
Analyzing the mass of behind-armor debris (BAD) generated by Rolled Homogeneous Armor (RHA) subjected to normal penetration of variable cross-section Explosively Formed Projectile (EFP) is the purpose of this paper. S...Analyzing the mass of behind-armor debris (BAD) generated by Rolled Homogeneous Armor (RHA) subjected to normal penetration of variable cross-section Explosively Formed Projectile (EFP) is the purpose of this paper. So theoretical analysis, numerical simulation and experimental data are combined to analyze the influence of variable cross-section characteristic on the time history of crater radius. Moreover the relationships between time history of crater radius (as well as mass of BAD) and the thickness of RHA (from 30mm to 70 mm) and the impact velocity of EFP (1650 m/s to 1860 m/s) are also investigated. The results indicate that: 1) being compared to the variable cross-section characteristic is ignored, the theoretical time history of crater radius is in better agreement with the simulation results when the variable cross-section characteristic is considered;2) being compared to the other three conditions of plug, the theoretical mass of BAD is in the best agreement with the simulation results when the shape of plug is frustum of a cone and the angle between generatrix and bottom is 45- and the axial length of mushroom is considered.展开更多
In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the ext...In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the extrusion ratio of various stages directly determines the size of corresponding stage strain by formula. In this paper, as an example of the two interim dies, three die combinations of different angles and extrusion ratio are designed. Aviation magnesium alloy ZM6 is studied, and the results show that dynamic recrystallization is even more complete when continuous shear deformation occurs, so that the refinement and homogenization of microstructure are obtained. By the use of different die combinations, the accumulative strain increases under the conditions of same total extrusion ratio. Thus, the refined crystalline strengthening effect of extrusion deformation can be further analyzed. Due to the dead-zone defects, the actual accumulative strain decreases significantly and the effect of microstructure and performance improvements also decreases with it. Therefore, the optimal design of die combination is the key to the process and product of CVCDE, which provides a scientific basis for the development of severe plastic deformation.展开更多
Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well ceme...Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.展开更多
The three dimensional variable cross-section roll forming is a kind of new metal forming technol- ogy which combines large forming force, multi-axis linkage movement and space synergic movement, and the sequential syn...The three dimensional variable cross-section roll forming is a kind of new metal forming technol- ogy which combines large forming force, multi-axis linkage movement and space synergic movement, and the sequential synergic movement of the ganged roller group is used to complete the metal sheet forming according to the shape of the complicated and variable forming part data. The control system should meet the demands of quick response to the test requirements of the product part. A new kind of real time data driving multi-axis linkage and synergic movement control strategy of 3D roll forming is put forward in the paper. In the new control strategy, the forming data are automatically generated according to the shape of the parts, and the multi-axis linkage movement together with cooperative motion among the six stands of the 3D roll forming machine is driven by the real-time information, and the control nodes are also driven by the forming data. The new control strategy is applied to a 48 axis 3D roll forming machine developed by our research center, and the control servo period is less than 10ms. A forming experiment of variable cross section part is carried out, and the forming preci- sion is better than ＋ 0.5mm by the control strategy. The result of the experiment proves that the control strategy has significant potentiality for the development of 3D roll forming production line with large scale, multi-axis ganged and svner^ic movement展开更多
Using ANSYS-CFX, a general purpose fluid dynamics program, the vortex-induced vibration(VIV) of a variable cross-section cylinder is simulated under uniform current with high Reynolds numbers. Large eddy simulation(LE...Using ANSYS-CFX, a general purpose fluid dynamics program, the vortex-induced vibration(VIV) of a variable cross-section cylinder is simulated under uniform current with high Reynolds numbers. Large eddy simulation(LES) is conducted for studying the fluid-structure interaction. The vortex shedding in the wake, the motion trajectories of a cylinder, the variation of drag and lift forces on the cylinder are analyzed. The results show that the vortices of variable cross-section cylinder are chaotic and are varying along the cylinder. In places where cross-sections are changing significantly, the vortices are more irregular. The motion trail of the cylinder is almost the same but irregular. The drag and lift coefficients of the cylinder are varying with the changes of diameters.展开更多
Due to the unique deformation characteristics of auxetic materials(Poisson’s ratioμ<0),they have better shock resistance and energy absorption properties than traditional materials.Inspired by the concept of vari...Due to the unique deformation characteristics of auxetic materials(Poisson’s ratioμ<0),they have better shock resistance and energy absorption properties than traditional materials.Inspired by the concept of variable crosssection design,a new auxetic re-entrant honeycomb structure is designed in this study.The detailed design method of re-entrant honeycomb with variable cross-section(VCRH)is provided,and five VCRH structures with the same relative density and different cross-section change rates are proposed.The in-plane impact resistance and energy absorption abilities of VCRH under constant velocity are investigated by ABAQUS/EXPLICIT.The results show that the introduction of variable cross-section design can effectively improve the impact resistance and energy absorption abilities of auxetic re-entrant honeycombs.The VCRH structure has better Young’s modulus,plateau stress,and specific energy absorption(SEA)than traditional re-entrant honeycomb(RH).The influence of microstructure parameters(such as cross-section change rateα)on the dynamic impact performance of VCRH is also studied.Results show that,with the increase in impact velocity andα,the plateau stress and SEA of VCRH increase.A positive correlation is also found between the energy absorption efficiency,impact load uniformity andαunder both medium and high impact speeds.These results can provide a reference for designing improved auxetic re-entrant honeycomb structures.展开更多
Flow channels with a variable cross-section are important components of piping system and are widely used in variousfields of engineering.Using afinite element method and modal analysis theory,flow-induced noise,mode ...Flow channels with a variable cross-section are important components of piping system and are widely used in variousfields of engineering.Using afinite element method and modal analysis theory,flow-induced noise,mode shapes,and structure-borne noise in such systems are investigated in this study.The results demonstrate that the maximum displacement and equivalent stress are located in the part with variable cross-sectional area.The aver-age excitation force on theflow channel wall increases with theflow velocity.The maximum excitation force occurs in the range of 0–20 Hz,and then it decreases gradually in the range of 20–1000 Hz.Additionally,as theflow velocity rises from 1 to 3 m/s,the overall sound pressure level associated with theflow-induced noise grows from 49.37 to 66.37 dB.Similarly,the overall sound pressure level associated with the structure-borne noise rises from 40.27 to 72.20 dB.When theflow velocity is increased,the increment of the structure-borne noise is higher than that of theflow-induced noise.展开更多
Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and sc...Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.展开更多
The longitudinal wave propagating in an elastic rod with a variable cross-section owns wide engineering background,in which the longitudinal wave dissipation determines some important performances of the slender struc...The longitudinal wave propagating in an elastic rod with a variable cross-section owns wide engineering background,in which the longitudinal wave dissipation determines some important performances of the slender structure.To reproduce the longitudinal wave dissipation effects on an elastic rod with a variable cross-section,a structure-preserving approach is developed based on the dynamic symmetry breaking theory.For the dynamic model controlling the longitudinal wave propagating in the elastic rod with the variable cross-section,the approximate multi-symplectic form is deduced based on the multi-symplectic method,and the expression of the local energy dissipation for the longitudinal wave propagating in the rod is presented,referring to the dynamic symmetry breaking theory.A structure-preserving method focusing on the residual of the multi-symplectic structure and the local energy dissipation of the dynamic model is constructed by using the midpoint difference discrete method.The longitudinal wave propagating in an elastic rod fixed at one end is simulated,and the local/total energy dissipations of the longitudinal wave are investigated by the constructed structure-preserving scheme in two typical cases in detail.展开更多
For a thin-walled box column with variable cross-section, the three governing equations for torsional-flexural buckling are ordinary differential equations of the second or fourth order with variable coefficients, so ...For a thin-walled box column with variable cross-section, the three governing equations for torsional-flexural buckling are ordinary differential equations of the second or fourth order with variable coefficients, so it is very difficult to solve them by means of an analytic method. In this paper, polynomials are used to approximate the geometric properties of cross-section and certain coefficients of the differential equations. Based on the energy principle and the Galerkin's method, the approximate formulas for calculating the flexural and torsional buckling loads of this kind of columns are developed respectively, and numerical examples are used to verify the correctness of the solutions obtained. The results calculated in this paper provide the basis for demonstrating the stability of thin-walled box columns with variable cross-section. This paper is of practical value.展开更多
The bending and free vibrational behaviors of functionally graded(FG)cylindrical beams with radially and axially varying material inhomogeneities are investigated.Based on a high-order cylindrical beam model,where the...The bending and free vibrational behaviors of functionally graded(FG)cylindrical beams with radially and axially varying material inhomogeneities are investigated.Based on a high-order cylindrical beam model,where the shear deformation and rotary inertia are both considered,the two coupled governing differential motion equations for the deflection and rotation are established.The analytical bending solutions for various boundary conditions are derived.In the vibrational analysis of FG cylindrical beams,the two governing equations are firstly changed to a single equation by means of an auxiliary function,and then the vibration mode is expanded into shifted Chebyshev polynomials.Numerical examples are given to investigate the effects of the material gradient indices on the deflections,the stress distributions,and the eigenfrequencies of the cylindrical beams,respectively.By comparing the obtained numerical results with those obtained by the three-dimensional(3D)elasticity theory and the Timoshenko beam theory,the effectiveness of the present approach is verified.展开更多
A novel variable stiffness model was proposed for analyzing elastic-plastic bending problems with arbitrary variable stiffness in detail.First,it was assumed that the material of a rectangular beam is an ideal isotrop...A novel variable stiffness model was proposed for analyzing elastic-plastic bending problems with arbitrary variable stiffness in detail.First,it was assumed that the material of a rectangular beam is an ideal isotropic elastic-plastic material,whose elastic modulus,yield strength,and section height are functions of the axial coordinates of the beam respectively.Considering the effect of shear on the deformation of the beam,the elastic and elastic-plastic bending problems of the axially variable stiffness beam were studied.Then,the analytical solutions of the elastic and elastic-plastic deformation of the beam were derived when the cross-section height and the elastic modulus of the material were varied by special function along the length of the beam respectively.The elastic and elastic-plastic analysis of the variable stiffness beam was carried out using Differential Quadrature Method(DQM)when the bending stiffness varied arbitrarily.The influence of the axial variation of the bending stiffness on the elastic and elastic-plastic deformation of the beam was analyzed by numerical simulation,DQM,and finite element method(FEM).Simulation results verified the practicability of the proposed mechanical model,and the comparison between the results of the solutions of DQM and FEM showed that DQM is accurate and effective in elastic and elastic-plastic analysis of variable stiffness beams.展开更多
The two coupled governing differential equations for the out-of-plane vibrations of non-uniform beams with variable curvature are derived via the Hamilton’s principle.These equations are expressed in terms of flexura...The two coupled governing differential equations for the out-of-plane vibrations of non-uniform beams with variable curvature are derived via the Hamilton’s principle.These equations are expressed in terms of flexural and torsional displacements simultaneously.In this study,the analytical method is proposed.Firstly,two physical parameters are introduced to simplify the analysis.One derives the explicit relations between the flexural and the torsional displacements which can also be used to reduce the difficulty in experimental measurements.Based on the relation,the two governing characteristic differential equations with variable coefficients can be uncoupled into a sixth-order ordinary differential equation in terms of the flexural displacement only.When the material and geometric properties of the beam are in arbitrary polynomial forms,the exact solutions with regard to the outof-plane vibrations of non-uniform beams with variable curvature can be obtained by the recurrence formula.In addition,the mode transition mechanism is revealed and the influence of several parameters on the vibration of the non-uniform beam with variable curvature is explored.展开更多
The paper presents the theoretical analysis of a variable stiffness beam. The bending stiffness EI varies continuously along the length of the beam. Dynamic equation yields differential equation with variable co- effi...The paper presents the theoretical analysis of a variable stiffness beam. The bending stiffness EI varies continuously along the length of the beam. Dynamic equation yields differential equation with variable co- efficients based on the model of the Euler-Bernoulli beam. Then differential equation with variable coefficients becomes that with constant coefficients by variable substitution. At last, the study obtains the solution of dy- namic equation. The cantilever beam is an object for analysis. When the flexural rigidity at free end is a constant and that at clamped end is varied, the dynamic characteristics are analyzed under several cases. The results dem- onstrate that the natural angular frequency reduces as the fiexural rigidity reduces. When the rigidity of clamped end is higher than that of free end, low-level mode contributes the larger displacement response to the total re- sponse. On the contrary, the contribution of low-level mode is lesser than that of hi^h-level mode.展开更多
基金funded by the National Key Research and Development Program of China(No.2024YFE0208100).
文摘The scroll expander,as the core component of the micro-compressed air energy storage and power generation system,directly affects the output efficiency of the system.Meanwhile,the scroll profile plays a central role in determining the output performance of the scroll expander.In this study,in order to investigate the output characteristics of a variable cross-section scroll expander,numerical simulation and experimental studies were con-ducted by using Computational Fluid Dynamics(CFD)methods and dynamic mesh techniques.The impact of critical parameters on the output performance of the scroll expander was analyzed through the utilization of the control variable method.It is found that increasing the inlet pressure and temperature within a certain range can improve the output power of the scroll expander.However,the increase in temperature and meshing clearance leads to a decline in the overall output performance of the scroll expander,leading to a decrease in volumetric efficiency by 8.43%and 12.79%,respectively.The experiments demonstrate that under equal inlet pressure conditions,increasing the inlet temperature elevates both the rotational speed and torque output of the scroll expander.Specifically,compared to operating at normal temperatures,the output torque increases by 21.8%under high-temperature conditions.However,the rate of speed and torque variation decreases as a consequence of enlarged meshing clearance,resulting in increased internal leakage and reduction in isentropic efficiency.
文摘A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.
基金Sponsored by the Subsidization Plan for Outstanding Young Teacher of Ministry of Education
文摘In order to understand mechanical characters and find out a calculating method for preflex beams used in particular bridge engineering projects, two types of simply supported preflex beams with variable crosssection, preflex beam with alterative web depth and preflex beam with aherative steel flange thickness, are dis- cussed on how to achieve the equivalent moment of inertia and Young＇ s modulus. Additionally, methods of cal- culating the equivalent bending stiffness and post-cracking deflection are proposed. Results of the experiments on 6 beams agree well with the theoretical analysis, which proves the correctness of the proposed formulas.
文摘This article analyzes the design of a variable-height simply supported steel truss bridge based on an actual project.It includes its basic situation,introduction to variable-height simply supported steel truss bridges,key design points of such bridges,and finite element analysis of the design effect.The analysis shows that for such bridges,reasonable main structure design and node design are the keys to determining the overall design idea,and through the reasonable application of the finite element analysis method,the design effect can be scientifically determined,providing a reference for the subsequent structural design of such projects.
基金Supported by National Key R&D Program of China(Grant No.2022YFB4701200)Ningbo Municipal Key Projects of Science and Technology Innovation 2025 Plan(Grant No.2022Z070)National Natural Science Foundation of China(Grant No.52205004).
文摘Variable stiffness mechanisms(VSMs)are a class of compliant mechanisms that can adjust their intrinsic stiffness,which promises to be beneficial in applications needed to interact with the environment,such as collaborative robots,wearable robots,and polishing robots.This paper presents the design and optimization of a novel linear VSM,called cLVSM,to produce linear motion,conversely to the majority of VSMs designed to perform rotary motion.By changing the effective length of specially designed circular beams,the cLVSM is capable of continuous stiffness regulation from a minimum value to almost rigid.Different from the VSMs which need rotation-to-translation converting mechanisms for stiffness regulation,the stiffness of the proposed design is adjusted by directly rotating the beams without the use of additional mechanisms,which contributes to improving the structural compactness,and reducing the energy loss and error in transmission.Moreover,the beam rotation needed to regulate the stiffness is almost perpendicular to the beam deflection force,which helps to reduce the torque needed for stiffness regulation.The stiffness model of the proposed VSM is developed using the screw theory,and the design parameters are optimized using the genetic algorithm.The effectiveness of the mathematical model and the performance of the design are verified by simulation and experiments.
文摘The behavior of beams with variable stiffness subjected to the action of variable loadings (impulse or harmonic) is analyzed in this paper using the successive approximation method. This successive approximation method is a technique for numerical integration of partial differential equations involving both the space and time, with well-known initial conditions on time and boundary conditions on the space. This technique, although having been applied to beams with constant stiffness, is new for the case of beams with variable stiffness, and it aims to use a quadratic parabola (in time) to approximate the solutions of the differential equations of dynamics. The spatial part is studied using the successive approximation method of the partial differential equations obtained, in order to transform them into a system of time-dependent ordinary differential equations. Thus, the integration algorithm using this technique is established and applied to examples of beams with variable stiffness, under variable loading, and with the different cases of supports chosen in the literature. We have thus calculated the cases of beams with constant or variable rigidity with articulated or embedded supports, subjected to the action of an instantaneous impulse and harmonic loads distributed over its entire length. In order to justify the robustness of the successive approximation method considered in this work, an example of an articulated beam with constant stiffness subjected to a distributed harmonic load was calculated analytically, and the results obtained compared to those found numerically for various steps (spatial h and temporal τ ¯ ) of calculus, and the difference between the values obtained by the two methods was small. For example for ( h=1/8 , τ ¯ =1/ 64 ), the difference between these values is 17%.
基金financially supported by the National Natural Science Foundation of China(Grant No.11372136)
文摘Analyzing the mass of behind-armor debris (BAD) generated by Rolled Homogeneous Armor (RHA) subjected to normal penetration of variable cross-section Explosively Formed Projectile (EFP) is the purpose of this paper. So theoretical analysis, numerical simulation and experimental data are combined to analyze the influence of variable cross-section characteristic on the time history of crater radius. Moreover the relationships between time history of crater radius (as well as mass of BAD) and the thickness of RHA (from 30mm to 70 mm) and the impact velocity of EFP (1650 m/s to 1860 m/s) are also investigated. The results indicate that: 1) being compared to the variable cross-section characteristic is ignored, the theoretical time history of crater radius is in better agreement with the simulation results when the variable cross-section characteristic is considered;2) being compared to the other three conditions of plug, the theoretical mass of BAD is in the best agreement with the simulation results when the shape of plug is frustum of a cone and the angle between generatrix and bottom is 45- and the axial length of mushroom is considered.
基金financially supported by the National Natural Science Foundation of China(No.51205094)
文摘In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the extrusion ratio of various stages directly determines the size of corresponding stage strain by formula. In this paper, as an example of the two interim dies, three die combinations of different angles and extrusion ratio are designed. Aviation magnesium alloy ZM6 is studied, and the results show that dynamic recrystallization is even more complete when continuous shear deformation occurs, so that the refinement and homogenization of microstructure are obtained. By the use of different die combinations, the accumulative strain increases under the conditions of same total extrusion ratio. Thus, the refined crystalline strengthening effect of extrusion deformation can be further analyzed. Due to the dead-zone defects, the actual accumulative strain decreases significantly and the effect of microstructure and performance improvements also decreases with it. Therefore, the optimal design of die combination is the key to the process and product of CVCDE, which provides a scientific basis for the development of severe plastic deformation.
基金This research was financially supported by the National Science Fund for Distinguished Young Scholars(Grant No.51825904)the National Science and Technology Major Project from the Ministry of Science and Technology(MOST)of China(Grant No.2016ZX05058004-005).
文摘Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.
基金Supported by National Key Technology R&D Program(No.2011BAG03B03)
文摘The three dimensional variable cross-section roll forming is a kind of new metal forming technol- ogy which combines large forming force, multi-axis linkage movement and space synergic movement, and the sequential synergic movement of the ganged roller group is used to complete the metal sheet forming according to the shape of the complicated and variable forming part data. The control system should meet the demands of quick response to the test requirements of the product part. A new kind of real time data driving multi-axis linkage and synergic movement control strategy of 3D roll forming is put forward in the paper. In the new control strategy, the forming data are automatically generated according to the shape of the parts, and the multi-axis linkage movement together with cooperative motion among the six stands of the 3D roll forming machine is driven by the real-time information, and the control nodes are also driven by the forming data. The new control strategy is applied to a 48 axis 3D roll forming machine developed by our research center, and the control servo period is less than 10ms. A forming experiment of variable cross section part is carried out, and the forming preci- sion is better than ＋ 0.5mm by the control strategy. The result of the experiment proves that the control strategy has significant potentiality for the development of 3D roll forming production line with large scale, multi-axis ganged and svner^ic movement
基金supported by the National Natural Science Foundation of China (Nos. 51179179 and 51079136)
文摘Using ANSYS-CFX, a general purpose fluid dynamics program, the vortex-induced vibration(VIV) of a variable cross-section cylinder is simulated under uniform current with high Reynolds numbers. Large eddy simulation(LES) is conducted for studying the fluid-structure interaction. The vortex shedding in the wake, the motion trajectories of a cylinder, the variation of drag and lift forces on the cylinder are analyzed. The results show that the vortices of variable cross-section cylinder are chaotic and are varying along the cylinder. In places where cross-sections are changing significantly, the vortices are more irregular. The motion trail of the cylinder is almost the same but irregular. The drag and lift coefficients of the cylinder are varying with the changes of diameters.
基金This research is supported by the National Natural Science Foundation of China(No.11902232).
文摘Due to the unique deformation characteristics of auxetic materials(Poisson’s ratioμ<0),they have better shock resistance and energy absorption properties than traditional materials.Inspired by the concept of variable crosssection design,a new auxetic re-entrant honeycomb structure is designed in this study.The detailed design method of re-entrant honeycomb with variable cross-section(VCRH)is provided,and five VCRH structures with the same relative density and different cross-section change rates are proposed.The in-plane impact resistance and energy absorption abilities of VCRH under constant velocity are investigated by ABAQUS/EXPLICIT.The results show that the introduction of variable cross-section design can effectively improve the impact resistance and energy absorption abilities of auxetic re-entrant honeycombs.The VCRH structure has better Young’s modulus,plateau stress,and specific energy absorption(SEA)than traditional re-entrant honeycomb(RH).The influence of microstructure parameters(such as cross-section change rateα)on the dynamic impact performance of VCRH is also studied.Results show that,with the increase in impact velocity andα,the plateau stress and SEA of VCRH increase.A positive correlation is also found between the energy absorption efficiency,impact load uniformity andαunder both medium and high impact speeds.These results can provide a reference for designing improved auxetic re-entrant honeycomb structures.
基金supported by the Key Research and Development Project of Shandong Province[2019GSF109084]the National Natural Science Foundation of China[51776111]Young Scholars Program of Shandong University[2018WLJH73].
文摘Flow channels with a variable cross-section are important components of piping system and are widely used in variousfields of engineering.Using afinite element method and modal analysis theory,flow-induced noise,mode shapes,and structure-borne noise in such systems are investigated in this study.The results demonstrate that the maximum displacement and equivalent stress are located in the part with variable cross-sectional area.The aver-age excitation force on theflow channel wall increases with theflow velocity.The maximum excitation force occurs in the range of 0–20 Hz,and then it decreases gradually in the range of 20–1000 Hz.Additionally,as theflow velocity rises from 1 to 3 m/s,the overall sound pressure level associated with theflow-induced noise grows from 49.37 to 66.37 dB.Similarly,the overall sound pressure level associated with the structure-borne noise rises from 40.27 to 72.20 dB.When theflow velocity is increased,the increment of the structure-borne noise is higher than that of theflow-induced noise.
基金financial support from the National Natural Science Foundation of China (No. 51675143)
文摘Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.
基金Projected supported by the National Natural Science Foundation of China(Nos.11872303,12172281,11972284)the Fund for Distinguished Young Scholars of Shaanxi Province of China(No.2019JC-29)+2 种基金the Foundation Strengthening Programme Technical Area Fund(No.2021-JCJQ-JJ-0565)the Fund of the Youth Innovation Team of Shaanxi Universitiesthe Open Foundation of State Key Laboratory of Structural Analysis of Industrial Equipment(No.GZ19103)。
文摘The longitudinal wave propagating in an elastic rod with a variable cross-section owns wide engineering background,in which the longitudinal wave dissipation determines some important performances of the slender structure.To reproduce the longitudinal wave dissipation effects on an elastic rod with a variable cross-section,a structure-preserving approach is developed based on the dynamic symmetry breaking theory.For the dynamic model controlling the longitudinal wave propagating in the elastic rod with the variable cross-section,the approximate multi-symplectic form is deduced based on the multi-symplectic method,and the expression of the local energy dissipation for the longitudinal wave propagating in the rod is presented,referring to the dynamic symmetry breaking theory.A structure-preserving method focusing on the residual of the multi-symplectic structure and the local energy dissipation of the dynamic model is constructed by using the midpoint difference discrete method.The longitudinal wave propagating in an elastic rod fixed at one end is simulated,and the local/total energy dissipations of the longitudinal wave are investigated by the constructed structure-preserving scheme in two typical cases in detail.
文摘For a thin-walled box column with variable cross-section, the three governing equations for torsional-flexural buckling are ordinary differential equations of the second or fourth order with variable coefficients, so it is very difficult to solve them by means of an analytic method. In this paper, polynomials are used to approximate the geometric properties of cross-section and certain coefficients of the differential equations. Based on the energy principle and the Galerkin's method, the approximate formulas for calculating the flexural and torsional buckling loads of this kind of columns are developed respectively, and numerical examples are used to verify the correctness of the solutions obtained. The results calculated in this paper provide the basis for demonstrating the stability of thin-walled box columns with variable cross-section. This paper is of practical value.
基金Project supported by the Natural Science Foundation of Guangdong Province of China(No.2018A030313258)。
文摘The bending and free vibrational behaviors of functionally graded(FG)cylindrical beams with radially and axially varying material inhomogeneities are investigated.Based on a high-order cylindrical beam model,where the shear deformation and rotary inertia are both considered,the two coupled governing differential motion equations for the deflection and rotation are established.The analytical bending solutions for various boundary conditions are derived.In the vibrational analysis of FG cylindrical beams,the two governing equations are firstly changed to a single equation by means of an auxiliary function,and then the vibration mode is expanded into shifted Chebyshev polynomials.Numerical examples are given to investigate the effects of the material gradient indices on the deflections,the stress distributions,and the eigenfrequencies of the cylindrical beams,respectively.By comparing the obtained numerical results with those obtained by the three-dimensional(3D)elasticity theory and the Timoshenko beam theory,the effectiveness of the present approach is verified.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51175058).
文摘A novel variable stiffness model was proposed for analyzing elastic-plastic bending problems with arbitrary variable stiffness in detail.First,it was assumed that the material of a rectangular beam is an ideal isotropic elastic-plastic material,whose elastic modulus,yield strength,and section height are functions of the axial coordinates of the beam respectively.Considering the effect of shear on the deformation of the beam,the elastic and elastic-plastic bending problems of the axially variable stiffness beam were studied.Then,the analytical solutions of the elastic and elastic-plastic deformation of the beam were derived when the cross-section height and the elastic modulus of the material were varied by special function along the length of the beam respectively.The elastic and elastic-plastic analysis of the variable stiffness beam was carried out using Differential Quadrature Method(DQM)when the bending stiffness varied arbitrarily.The influence of the axial variation of the bending stiffness on the elastic and elastic-plastic deformation of the beam was analyzed by numerical simulation,DQM,and finite element method(FEM).Simulation results verified the practicability of the proposed mechanical model,and the comparison between the results of the solutions of DQM and FEM showed that DQM is accurate and effective in elastic and elastic-plastic analysis of variable stiffness beams.
文摘The two coupled governing differential equations for the out-of-plane vibrations of non-uniform beams with variable curvature are derived via the Hamilton’s principle.These equations are expressed in terms of flexural and torsional displacements simultaneously.In this study,the analytical method is proposed.Firstly,two physical parameters are introduced to simplify the analysis.One derives the explicit relations between the flexural and the torsional displacements which can also be used to reduce the difficulty in experimental measurements.Based on the relation,the two governing characteristic differential equations with variable coefficients can be uncoupled into a sixth-order ordinary differential equation in terms of the flexural displacement only.When the material and geometric properties of the beam are in arbitrary polynomial forms,the exact solutions with regard to the outof-plane vibrations of non-uniform beams with variable curvature can be obtained by the recurrence formula.In addition,the mode transition mechanism is revealed and the influence of several parameters on the vibration of the non-uniform beam with variable curvature is explored.
基金National Natural Science Foundation of China(No.51178175)
文摘The paper presents the theoretical analysis of a variable stiffness beam. The bending stiffness EI varies continuously along the length of the beam. Dynamic equation yields differential equation with variable co- efficients based on the model of the Euler-Bernoulli beam. Then differential equation with variable coefficients becomes that with constant coefficients by variable substitution. At last, the study obtains the solution of dy- namic equation. The cantilever beam is an object for analysis. When the flexural rigidity at free end is a constant and that at clamped end is varied, the dynamic characteristics are analyzed under several cases. The results dem- onstrate that the natural angular frequency reduces as the fiexural rigidity reduces. When the rigidity of clamped end is higher than that of free end, low-level mode contributes the larger displacement response to the total re- sponse. On the contrary, the contribution of low-level mode is lesser than that of hi^h-level mode.
