According to the Mohr-Coulomb yield criterion, the stress field of the infinite slope is derived under a vertical uniform load q on the top of the slope. It is indicated that elastic and elasto-plastic states would oc...According to the Mohr-Coulomb yield criterion, the stress field of the infinite slope is derived under a vertical uniform load q on the top of the slope. It is indicated that elastic and elasto-plastic states would occur in the slope. When q is smaller than the critical load, q(p), the slope is in the elastic state. If q equals q(p), the slope is in the critical state, and the plastic deformation would occur along the critical angle. With the increase of q, the plastic zone would extend, and the slope is in the elasto-plastic State. If q equals limit load, the slope is in the limit equilibrium state. The slope may be divided into three zones. Some charts of the critical angle, the critical and limit load coefficients are presented in this paper.展开更多
When one end of an air-dry igneous rock block was uniaxially loaded in laboratory, there appeared an electromotive force that made electric currents flow from the stressed volume to the unstressed volume. Quartz-free ...When one end of an air-dry igneous rock block was uniaxially loaded in laboratory, there appeared an electromotive force that made electric currents flow from the stressed volume to the unstressed volume. Quartz-free rocks such as gabbro also generated this force, stronger than quartz-bearing rocks such as granite. This indicates that the piezoelectric effect of quartz and the electrokinetic effect of pore water do not make a large contribution toward generating the electromotive force. We focus on peroxy bond that is one of the abundant lattice defects in igneous rock-forming minerals. When mechanical loading deforms the lattice structure around this defect and breaks its bond, its energy levels change and act like an accepter. As an electron is trapped at this defect from a neighbor 02- site, a positive hole is activated there. They attempt to diffuse toward the unstressed volume through the valence band and are simultaneously affected by the attractive electric force with the electrons trapped in peroxy bonds. This leads to a polarization in the stressed volume and the generation of electromotive force between the stressed and unstressed volumes. Similar electromotive force may be generated in the Earth＇s crust where inhomogeneous stress/strain is changing.展开更多
1 Introduction In highway construction,flled embankments are trapezoidal,and the ground is always improved by sand wells or columns.During embankment construction,because the width and height of the embankment are cha...1 Introduction In highway construction,flled embankments are trapezoidal,and the ground is always improved by sand wells or columns.During embankment construction,because the width and height of the embankment are changing,a non-uniform load that varies with time and lateral location is applied to the underlying ground.The consolidation phenomenon under two-dimensional(2D)conditions will keep pace with the construction of the embankment.In addition,because of evaporation and rainfall,the soils are mostly unsaturated.Therefore,it is meaningful to research the consolidation properties of unsaturated ground under non-uniform loading.展开更多
In this paper, using of the superposition principle. the bending solution ofrectangular plate with one edge built-in and one corner point supported subjected touniform load is derived. The results indicate the method ...In this paper, using of the superposition principle. the bending solution ofrectangular plate with one edge built-in and one corner point supported subjected touniform load is derived. The results indicate the method has the advantages of rabidconvergence and high precision.展开更多
An uncertainty analysis method is proposed for the assessment of the residual strength of a casing subjected to wear and non-uniform load in a deep well.The influence of casing residual stress,out-of-roundness and non...An uncertainty analysis method is proposed for the assessment of the residual strength of a casing subjected to wear and non-uniform load in a deep well.The influence of casing residual stress,out-of-roundness and non-uniform load is considered.The distribution of multi-source parameters related to the residual anti extrusion strength and residual anti internal pressure strength of the casing after wear are determined using the probability theory.Considering the technical casing of X101 well in Xinjiang Oilfield as an example,it is shown that the randomness of casing wear depth,formation elastic modulus and formation Poisson’s ratio are the main factors that affect the uncertainty of residual strength.The wider the confidence interval is,the greater the uncertainty range is.Compared with the calculations resulting from the proposed uncertainty analysis method,the residual strength obtained by means of traditional single value calculation method is either larger or smaller,which leads to the conclusion that the residual strength should be considered in terms of a range of probabilities rather than a single value.展开更多
Based on one type of practical Biot＇s equation and the dynamic-stiffness matrices ofa poroelastic soil layer and half-space, Green＇s functions were derived for unitformly distributed loads acting on an inclined line...Based on one type of practical Biot＇s equation and the dynamic-stiffness matrices ofa poroelastic soil layer and half-space, Green＇s functions were derived for unitformly distributed loads acting on an inclined line in a poroelastie layered site. This analysis overcomes significant problems in wave scattering due to local soil conditions and dynamic soil-structure interaction. The Green＇s functions can be reduced to the case of an elastic layered site developed by Wolf in 1985. Parametric studies are then carried out through two example problems.展开更多
The differential equations of the axisymmetric large amplitude free vibration for circular sandwich plates under static load are derived, and a set of nonlinearly coupled algebraic and differential eigenvalue equation...The differential equations of the axisymmetric large amplitude free vibration for circular sandwich plates under static load are derived, and a set of nonlinearly coupled algebraic and differential eigenvalue equations of the problem are formulated following an assumed time mode approach suggested. The analytic solutions are presented and a relation for amplitude frequency-load of the plates with edge clamped is derived by modified iteration method. The effects of static load on vibrations of plates are investigated.展开更多
During the excavation of deep coal and rock mass, the radial stress of the free face changes from three-dimensional compression state to two-dimensional stress, bearing the combined action of dynamic disturbance and s...During the excavation of deep coal and rock mass, the radial stress of the free face changes from three-dimensional compression state to two-dimensional stress, bearing the combined action of dynamic disturbance and static load at the same time. With that, many mines suffer from dynamic disasters, such as coal and gas outburst, rock burst and rock caving during deep mining excavation, which is often accompanied by plate crack, spalling and other disasters, seriously affecting the stability of stope and roadway. Taking thin rectangular coal and rock mass as the research object, the dual equation of the free vibration was derived and the exact solution model of the free vibration was established with the use of Hamilton dual system. Based on the action characteristics of the uniform impact load, the effective mode of the forced vibration was obtained by using the Duhamel integral principle and the orthogonality of the mode function. Based on the third strength theory and the numerical simulation results, the dynamic damage process and development trend of coal and rock mass were analyzed under uniform impact load. It was concluded that the starting position of dynamic damage can be judged by the first order main mode, and the development direction and trend of the damage can be judged by the fifth and sixth order main modes. It was concluded that the vibration mode functions of coal and rock mass with four side fixed (C-C-C-C), the two sides fixed and simply supported on the other (S-C-S-C) are mainly composed of three modes that are the first order (dominant frequency), the fifth order and the sixth order, from which the dynamic damage mechanism is preliminarily studied.展开更多
Natural frequencies of the bridge—vehicle coupling system considering uniform distributed load varying with position is investigated in this work.An analytic model of a simply supported beam bridge with constant sect...Natural frequencies of the bridge—vehicle coupling system considering uniform distributed load varying with position is investigated in this work.An analytic model of a simply supported beam bridge with constant section is introduced to establish the frequency equations of the coupled system.Comparisons with the results between analytic model and FEM indicate that the present research is correct and reasonable.In view of an example bridge,natural frequencies are studied on the bridge subjected to uniform distributed moving loads in cases of different weight and span,by which some regular phenomenon are obtained.The present study can apply in the engineering problem of interaction between bridges and moving loads such as trains and tracked vehicles.展开更多
The aim of this study is to calculate the critical load of variable inertia columns. The example studied in this paper can be used as a paradigm for other non-uniform columns. The wavelength of equivalent vibratory sy...The aim of this study is to calculate the critical load of variable inertia columns. The example studied in this paper can be used as a paradigm for other non-uniform columns. The wavelength of equivalent vibratory system is used to calculate the critical load of the trigonometrically varied inertia column. In doing so, the equilibrium equation of the column is theoretically studied using the perturbation method. Accuracy of the calculated results is evaluated by comparing the solution with numerical results. Effect of improving the initial guess on the solution accuracy is investigated. Effects of varying parameters of the trigonometrically varied inertia and the uniformly tapered columns on their stability behavior are studied. Finally, using the so-called ＂perfectibility＂ parameter, two design goals, i.e., being lightweight and being strong, are studied for the discussed columns.展开更多
It is desirable to get a uniform load distribution for the pressure rollers of the mangle.In thispaper,the load uniforming principle of the axially-staggered pressure rollers and the rules for theroller design have be...It is desirable to get a uniform load distribution for the pressure rollers of the mangle.In thispaper,the load uniforming principle of the axially-staggered pressure rollers and the rules for theroller design have been analysed by the theory of bending of beams.The ratio of maximum tominimum value of the distributed load in the nip being taken as a useful index to describe the uni-formity of the load distribution,the performance of the so-called load-uniforming pressure rollerswith rubber covering,under various operation conditions,has been evaluated.As a result,it isproved that the load-uniforming pressure rollers with axially-staggered contact is a pratically use-ful means of uniformizing the load distribution,which ensures that the mangle will squeeze the ma-terial to be processed uniformly over its whole width under any technological load,and needs onlysome simple regulations.The conclusions obtained in this paper can easily be extended to the pressure rollers with anysupport conditions.展开更多
The paper investigates the response of non-initially stressed Euler-Bernoulli beam to uniform partially distributed moving loads. The governing partial differential equations were analyzed for both moving force and mo...The paper investigates the response of non-initially stressed Euler-Bernoulli beam to uniform partially distributed moving loads. The governing partial differential equations were analyzed for both moving force and moving mass problem in order to determine the behaviour of the system under consideration. The analytical method in terms of series solution and numerical method were used for the governing equation. The effect of various beam observed that the response amplitude due to the moving force is greater than that due to moving mass. It was also found that the response amplitude of the moving force problem with non-initial stress increase as mass of the mass of the load M increases.展开更多
The water level rising rate of Tangshan mine well significantly accelerated in 2010,and the ascensional range was obviously higher than that of the same period in previous years.From the view of groundwater dynamics a...The water level rising rate of Tangshan mine well significantly accelerated in 2010,and the ascensional range was obviously higher than that of the same period in previous years.From the view of groundwater dynamics and loading effects,and based on the water pumping( pouring) water test model and semi-infinite elastic space theory model under uniform load,the effects of grouting and loading of nearby building construction on the well water level were analyzed. Results show that grouting at a distance of 200 ~ 700 m to the well,with amount of 2500m3 per day and duration of 270 d,can cause an 8 ~ 11 m rise of well water level; and loading of large-area building construction can cause about a 4m rise of well water level. Through the analysis of these factors,we find that the water level anomalous rising of Tangshan mine well was relevant to grouting and loading of the nearby building construction. This study provides a scientific basis for anomalous rising analysis of water level of Tangshan mine well.展开更多
A new strategy for elastic modulus adjustment is proposed based on the element bearing ratio （EBR）,and the elastic modulus reduction method （EMRM） is proposed for limit load evaluation of frame structures. The EBR...A new strategy for elastic modulus adjustment is proposed based on the element bearing ratio （EBR）,and the elastic modulus reduction method （EMRM） is proposed for limit load evaluation of frame structures. The EBR is defined employing the generalized yield criterion,and the reference EBR is determined by introducing the extrema and the degree of uniformity of EBR in the structure. The elastic modulus in the element with an EBR greater than the reference one is reduced based on the linear elastic finite element analysis and the equilibrium of strain energy. The lower-bound of limit-loads of frame structures are analyzed and the numerical example demonstrates the flexibility,accuracy and effciency of the proposed method.展开更多
文摘According to the Mohr-Coulomb yield criterion, the stress field of the infinite slope is derived under a vertical uniform load q on the top of the slope. It is indicated that elastic and elasto-plastic states would occur in the slope. When q is smaller than the critical load, q(p), the slope is in the elastic state. If q equals q(p), the slope is in the critical state, and the plastic deformation would occur along the critical angle. With the increase of q, the plastic zone would extend, and the slope is in the elasto-plastic State. If q equals limit load, the slope is in the limit equilibrium state. The slope may be divided into three zones. Some charts of the critical angle, the critical and limit load coefficients are presented in this paper.
基金partially supported by"Observation and Research Program for Prediction of Earthquakes and Volcanic Eruptions"of the Ministry of Education,Culture,Sports,Science and Technology of Japan,"FY2010 Research Incentive Assistance Program"of Educational System General Research Organization,Tokai University"Individual Research Projects"of Institute of Oceanic Development of Science and Technology,Tokai University
文摘When one end of an air-dry igneous rock block was uniaxially loaded in laboratory, there appeared an electromotive force that made electric currents flow from the stressed volume to the unstressed volume. Quartz-free rocks such as gabbro also generated this force, stronger than quartz-bearing rocks such as granite. This indicates that the piezoelectric effect of quartz and the electrokinetic effect of pore water do not make a large contribution toward generating the electromotive force. We focus on peroxy bond that is one of the abundant lattice defects in igneous rock-forming minerals. When mechanical loading deforms the lattice structure around this defect and breaks its bond, its energy levels change and act like an accepter. As an electron is trapped at this defect from a neighbor 02- site, a positive hole is activated there. They attempt to diffuse toward the unstressed volume through the valence band and are simultaneously affected by the attractive electric force with the electrons trapped in peroxy bonds. This leads to a polarization in the stressed volume and the generation of electromotive force between the stressed and unstressed volumes. Similar electromotive force may be generated in the Earth＇s crust where inhomogeneous stress/strain is changing.
基金supported by the National Nature Science Foundation of China(No.12172211)the National Key Research and Development Program of China(No.2019YFC1509800)。
文摘1 Introduction In highway construction,flled embankments are trapezoidal,and the ground is always improved by sand wells or columns.During embankment construction,because the width and height of the embankment are changing,a non-uniform load that varies with time and lateral location is applied to the underlying ground.The consolidation phenomenon under two-dimensional(2D)conditions will keep pace with the construction of the embankment.In addition,because of evaporation and rainfall,the soils are mostly unsaturated.Therefore,it is meaningful to research the consolidation properties of unsaturated ground under non-uniform loading.
文摘In this paper, using of the superposition principle. the bending solution ofrectangular plate with one edge built-in and one corner point supported subjected touniform load is derived. The results indicate the method has the advantages of rabidconvergence and high precision.
基金supported by the National Natural Science Foundation of China[51804061,51974052,51774063]the Academician Led Special Project of Chongqing Science and Technology Commission[cstc2017zdcy-yszxX0009]+1 种基金the Chongqing Research Program of Basic Research and Frontier Technology[cstc2019jcyj-msxmX0199,cstc2018jcyjAX0417]the Chongqing Education Committee foundation[KJQN201901544,KJZD-K201801501].
文摘An uncertainty analysis method is proposed for the assessment of the residual strength of a casing subjected to wear and non-uniform load in a deep well.The influence of casing residual stress,out-of-roundness and non-uniform load is considered.The distribution of multi-source parameters related to the residual anti extrusion strength and residual anti internal pressure strength of the casing after wear are determined using the probability theory.Considering the technical casing of X101 well in Xinjiang Oilfield as an example,it is shown that the randomness of casing wear depth,formation elastic modulus and formation Poisson’s ratio are the main factors that affect the uncertainty of residual strength.The wider the confidence interval is,the greater the uncertainty range is.Compared with the calculations resulting from the proposed uncertainty analysis method,the residual strength obtained by means of traditional single value calculation method is either larger or smaller,which leads to the conclusion that the residual strength should be considered in terms of a range of probabilities rather than a single value.
基金National Natural Science Foundation of China Under Grant No.50378063
文摘Based on one type of practical Biot＇s equation and the dynamic-stiffness matrices ofa poroelastic soil layer and half-space, Green＇s functions were derived for unitformly distributed loads acting on an inclined line in a poroelastie layered site. This analysis overcomes significant problems in wave scattering due to local soil conditions and dynamic soil-structure interaction. The Green＇s functions can be reduced to the case of an elastic layered site developed by Wolf in 1985. Parametric studies are then carried out through two example problems.
文摘The differential equations of the axisymmetric large amplitude free vibration for circular sandwich plates under static load are derived, and a set of nonlinearly coupled algebraic and differential eigenvalue equations of the problem are formulated following an assumed time mode approach suggested. The analytic solutions are presented and a relation for amplitude frequency-load of the plates with edge clamped is derived by modified iteration method. The effects of static load on vibrations of plates are investigated.
文摘During the excavation of deep coal and rock mass, the radial stress of the free face changes from three-dimensional compression state to two-dimensional stress, bearing the combined action of dynamic disturbance and static load at the same time. With that, many mines suffer from dynamic disasters, such as coal and gas outburst, rock burst and rock caving during deep mining excavation, which is often accompanied by plate crack, spalling and other disasters, seriously affecting the stability of stope and roadway. Taking thin rectangular coal and rock mass as the research object, the dual equation of the free vibration was derived and the exact solution model of the free vibration was established with the use of Hamilton dual system. Based on the action characteristics of the uniform impact load, the effective mode of the forced vibration was obtained by using the Duhamel integral principle and the orthogonality of the mode function. Based on the third strength theory and the numerical simulation results, the dynamic damage process and development trend of coal and rock mass were analyzed under uniform impact load. It was concluded that the starting position of dynamic damage can be judged by the first order main mode, and the development direction and trend of the damage can be judged by the fifth and sixth order main modes. It was concluded that the vibration mode functions of coal and rock mass with four side fixed (C-C-C-C), the two sides fixed and simply supported on the other (S-C-S-C) are mainly composed of three modes that are the first order (dominant frequency), the fifth order and the sixth order, from which the dynamic damage mechanism is preliminarily studied.
文摘Natural frequencies of the bridge—vehicle coupling system considering uniform distributed load varying with position is investigated in this work.An analytic model of a simply supported beam bridge with constant section is introduced to establish the frequency equations of the coupled system.Comparisons with the results between analytic model and FEM indicate that the present research is correct and reasonable.In view of an example bridge,natural frequencies are studied on the bridge subjected to uniform distributed moving loads in cases of different weight and span,by which some regular phenomenon are obtained.The present study can apply in the engineering problem of interaction between bridges and moving loads such as trains and tracked vehicles.
文摘The aim of this study is to calculate the critical load of variable inertia columns. The example studied in this paper can be used as a paradigm for other non-uniform columns. The wavelength of equivalent vibratory system is used to calculate the critical load of the trigonometrically varied inertia column. In doing so, the equilibrium equation of the column is theoretically studied using the perturbation method. Accuracy of the calculated results is evaluated by comparing the solution with numerical results. Effect of improving the initial guess on the solution accuracy is investigated. Effects of varying parameters of the trigonometrically varied inertia and the uniformly tapered columns on their stability behavior are studied. Finally, using the so-called ＂perfectibility＂ parameter, two design goals, i.e., being lightweight and being strong, are studied for the discussed columns.
文摘It is desirable to get a uniform load distribution for the pressure rollers of the mangle.In thispaper,the load uniforming principle of the axially-staggered pressure rollers and the rules for theroller design have been analysed by the theory of bending of beams.The ratio of maximum tominimum value of the distributed load in the nip being taken as a useful index to describe the uni-formity of the load distribution,the performance of the so-called load-uniforming pressure rollerswith rubber covering,under various operation conditions,has been evaluated.As a result,it isproved that the load-uniforming pressure rollers with axially-staggered contact is a pratically use-ful means of uniformizing the load distribution,which ensures that the mangle will squeeze the ma-terial to be processed uniformly over its whole width under any technological load,and needs onlysome simple regulations.The conclusions obtained in this paper can easily be extended to the pressure rollers with anysupport conditions.
文摘The paper investigates the response of non-initially stressed Euler-Bernoulli beam to uniform partially distributed moving loads. The governing partial differential equations were analyzed for both moving force and moving mass problem in order to determine the behaviour of the system under consideration. The analytical method in terms of series solution and numerical method were used for the governing equation. The effect of various beam observed that the response amplitude due to the moving force is greater than that due to moving mass. It was also found that the response amplitude of the moving force problem with non-initial stress increase as mass of the mass of the load M increases.
基金funded by the Earthquake Tracking Contract Orientated Task,CEA(2011020303)Science and Technology Project of Hebei Province(13275407D)
文摘The water level rising rate of Tangshan mine well significantly accelerated in 2010,and the ascensional range was obviously higher than that of the same period in previous years.From the view of groundwater dynamics and loading effects,and based on the water pumping( pouring) water test model and semi-infinite elastic space theory model under uniform load,the effects of grouting and loading of nearby building construction on the well water level were analyzed. Results show that grouting at a distance of 200 ~ 700 m to the well,with amount of 2500m3 per day and duration of 270 d,can cause an 8 ~ 11 m rise of well water level; and loading of large-area building construction can cause about a 4m rise of well water level. Through the analysis of these factors,we find that the water level anomalous rising of Tangshan mine well was relevant to grouting and loading of the nearby building construction. This study provides a scientific basis for anomalous rising analysis of water level of Tangshan mine well.
基金supported by the National Natural Science Foundation of China (No. 50768001)the Foundation of New Century Excellent Talents in University (No. NCET-04-0834)the Guangxi Natural Science Foundation (No. 0728026)
文摘A new strategy for elastic modulus adjustment is proposed based on the element bearing ratio （EBR）,and the elastic modulus reduction method （EMRM） is proposed for limit load evaluation of frame structures. The EBR is defined employing the generalized yield criterion,and the reference EBR is determined by introducing the extrema and the degree of uniformity of EBR in the structure. The elastic modulus in the element with an EBR greater than the reference one is reduced based on the linear elastic finite element analysis and the equilibrium of strain energy. The lower-bound of limit-loads of frame structures are analyzed and the numerical example demonstrates the flexibility,accuracy and effciency of the proposed method.
