Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method mor...Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method more easily controls the crystallization rate and is suitable for preparing large-area per-ovskite devices.However,the residual low-conductivity iodide layer in the two-step method can affect carrier transport and device stability,and the different crystallization rates of Sn-and Pb-based per-ovskites may result in poor film quality.Therefore,Sn-Pb mixed perovskites are mainly prepared by a one-step method.Herein,a MAPb_(0.5)Sn_(0.5)I_(3)-based self-powered photodetector without a hole transport layer is fabricated by a two-step method.By adjusting the concentration of the ascorbic acid(AA)addi-tive,the final perovskite film exhibited a pure phase without residues,and the optimal device exhibited a high responsivity(0.276 A W^(-1)),large specific detectivity(2.38×10^(12) Jones),and enhanced stability.This enhancement is mainly attributed to the inhibition of Sn2+oxidation,the control of crystal growth,and the sufficient reaction between organic ammonium salts and bottom halides due to the AA-induced pore structure.展开更多
A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,conf...A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,confocal laser microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,transmission electron microscopy,and electrochemical analysis,are employed to characterize MAO coatings at different stages of preparation.MAO has MgO,hydroxyapatite,Ca_(3)(PO_(4))_(2),and Mg2SiO4 phases.Its microstructure of the coating is characterized by"multiple breakdowns,pores within pores",and"repaired blind pores".The porosity and the uniformity of MAO coating first declines in the constant voltage mode,then augments while the discharge phenomenon takes place,and finally decreases in the repair stage.These analyses reveal a four-stage growth pattern for MAO coatings:anodic oxidation stage,micro-arc oxidation stage,breakdown stage,and repairing stage.During anodic oxidation and MAO stages,inward growth prevails,while the breakdown stage sees outward and accelerated growth.Simultaneous inward and outward growth in the repair stage results in a denser,more uniform coating with increased thickness and improved corrosion resistance.展开更多
High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production meth...High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.展开更多
The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationsh...The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationship between the diffusion coefficient along the direction of z-axis which is normal to the Mg/Zn interface and temperature was investigated, and the AF＇s impact on the diffusion constant （D0） and activation energy （Q^＊） was studied. Then, two steps were taken to simulate the atomic diffusion process and the formation of new phases： one for acceleration and the other for equilibration. The results show that： the Arrhenius equation works well for the description of Dz with different accelerating factors; the AF has no effect on the diffusion constant Do in the case of no phase transition; and the relationship between Q＊ and Q conforms to Q^＊=Q/A. Then, the new Arrhenius equation for AFHD is successfully constructed as Dz=Doexp[-Q/（ART）]. Meanwhile, the authentic equilibrium conformations at any dynamic moment can only be reproduced by the equilibration simulation of the HD-simulated configurations. Key words： accelerating factor method; Arrhenius equation; two-steps scheme; Mg/Zn interface; hyperdynamic simulation展开更多
Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from...Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.展开更多
Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of un...Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of unsteady flows.To enhance computational efficiency,we propose the Implicit-Explicit Two-Step Runge-Kutta(IMEX-TSRK)time-stepping discretization methods for unsteady flows,and develop a novel adaptive algorithm that correctly partitions spatial regions to apply implicit or explicit methods.The novel adaptive IMEX-TSRK schemes effectively handle the numerical stiffness of the small grid size and improve computational efficiency.Compared to implicit and explicit Runge-Kutta(RK)schemes,the IMEX-TSRK methods achieve the same order of accuracy with fewer first derivative calculations.Numerical case tests demonstrate that the IMEX-TSRK methods maintain numerical stability while enhancing computational efficiency.Specifically,in high Reynolds number flows,the computational efficiency of the IMEX-TSRK methods surpasses that of explicit RK schemes by more than one order of magnitude,and that of implicit RK schemes several times over.展开更多
In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to character...In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to characterize the strength of the backfill. However, the actual working temperature of slopes varies, and natural phenomena such as rainfall and groundwater infiltration commonly result in unsaturated soil conditions, with cracks typically present in cohesive slopes. This study introduces a novel approach for assessing the stability of unsaturated soil stepped slopes under varying temperatures, incorporating the effects of open and vertical cracks. Utilizing the kinematic approach and gravity increase method, we developed a three-dimensional (3D) rotational wedge failure mechanism to simulate slope collapse, enhancing the traditional two-dimensional analyses. We integrated temperature-dependent functions and nonlinear shear strength equations to evaluate the impact of temperature on four typical unsaturated soil types. A particle swarm optimization algorithm was employed to calculate the safety factor, ensuring our method’s accuracy by comparing it with existing studies. The results indicate that considering 3D effects yields a higher safety factor, while cracks reduce slope stability. Each unsaturated soil exhibits a distinctive temperature response curve, highlighting the importance of understanding soil types in the design phase.展开更多
In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-s...In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-step annealing protocol(H_(2)/Ar,600 and 800℃)to circumvent the sintering issues imposed by conventional thermodynamics.Physical characterizations(X-ray diffraction,high-angle annular dark-field scanning transmission electron microscopy,X-ray absorption spectroscopy)and theoretical calculations reveal that low-temperature annealing at 600℃stabilizes sub-nano disordered PtFe alloys via the strong metal-support interactions(SMSI)between Zn in ZnNC and Pt precursors,while high-temperature treatment at 800℃promotes Zn diffusion from the support into the alloy bulk and simultaneously triggers the disorder-to-order phase transition.The as-prepared ZnNC-15PtFeZn exhibits an initial mass activity of 0.769 mA/μgPt and retains 61.7%of its activity after 30000 cycles of accelerated stress testing(AST).Notably,when used as a cathode catalyst in MEA,ZnNC-15PtFeZn achieves superior power density(2.018 W/cm^(2)under H_(2)-O_(2))at half the Pt loading(0.05 mg/cm^(2))of state-of-the-art commercial Pt/C,highlighting its potential for low-Pt PEMFCs.Density functional theory confirms that Fe enhances ORR activity via ligand effects,while Zn strengthens Pt-Fe/Zn bonding(elevating vacancy formation energies),thereby improving structural stability.This mild,scalable aqueous impregnation strategy offers a general approach for synthesizing multi-component ordered alloys in electrocatalysis.展开更多
Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based...Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based BMGs,restricting their commercial applications significantly.In this study,this challenge was addressed by introducing a two-step alloying strategy to mitigate the remarkable density increment effect associated with heavy alloying elements required for enhancing the GFA.Consequently,through two-step alloying with Al and Fe in sequence,simultaneous enhancements in specific strength and GFA were achieved based on a Ti-Zr-Be ternary metallic glass,resulting in the development of a series of centimeter-sized metallic glasses exhibiting ultrahigh-specific strength.Notably,the newly developed(Ti_(45)Zr_(20)Be_(31)A_(l4))_(94)Fe_(6)alloy established a new record for the specific strength of Ti-based BMGs.Along with a critical diameter(D_(c))of 10 mm,it offers the optimal scheme for balancing the specific strength and GFA of Ti-based BMGs.The present results further brighten the application prospects of Ti-based BMGs as lightweight materials.展开更多
Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer ...Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer MoS_(2) has improved electron mobility and current density, and therefore provides a more promising platform in terms of thin-film transistors, flexible electronic devices, etc. However, the synthesis of large-area, high-quality multilayer MoS_(2) films with controlled layer number remains a challenge. Here, we develop a two-step oxygen-assisted chemical vapor deposition(OA-CVD) methodology for the synthesis of 4-inch MoS_(2) films from monolayer to trilayer on sapphire substrates. The influence of critical growth parameters on the growth of multilayer MoS_(2) is systematically explored, such as the evaporation temperature of MoO_(3) and the flow rate of O_(2). Flexible field-effect transistor(FET) devices fabricated from bilayer/trilayer MoS_(2) show substantial improvements in mobility compared with flexible FETs based on monolayer films.展开更多
In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during ...In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during the bio-oxidation step was used. The results revealed that the optimum mode was to maintain solution p H at 1.0-1.2 during the biological oxidation stage. Under this condition, the activity of mixed culture could be sustained and the formation of jarosite could be diminished, thus the oxidation efficiency was improved. The oxidation levels of iron and sulfur were improved by 12.50% and 15.49%, and the gold recovery was increased by 21.02%. Therefore, the two-step process combined with p H control is an effective method for oxidizing the biohydrometallurgical process of Axi gold concentrate, and it will have a broad prospect of application in dealing with complex refractory gold concentrate.展开更多
[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first ...[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first phase（0-10 h）was to improve cell growth,and the second phase（10-30 h）was to promote spore formation.Four factors including initial glucose concentration,fermentation pH,temperature（in the second phase）and shaking speed（in the second phase）were optimized using the methods of single factor test and orthogonal experiment.[Result] The initial glucose concentration showed a significant effect on sporulation.The optimal conditions for the spore formation of B.subtilis B579 were as follows：initial glucose concentration 5 g/L,fermentation pH 7.0,the temperature for the first phase 37 ℃,and the shaking speed for the first phase 180 r/min,the temperature for the second phase 40 ℃,and the shaking speed for the second phase 200 r/min;in addition,the first phase was 10 h and the second phase of fermentation was conducted for 30 h.Under such conditions,the spore concentration and spore formation rate could reach 9.43×108 CFU/ml and 90.99%,respectively,which represented 6.70-fold and 2.43-fold increase compared with those before optimization.[Conclusion] The spores concentration of biocontrol agent was improved using two-step control strategy,which provided the basis for biopesticide production in large scale.展开更多
The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that ...The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that the initial T1 ageing contributes a major increase of the tensile strength, and the 0.2% proof stress value reaches 482 MPa after ageing for 7 h at 115℃. Behavioral differences in the tensile properties of the alloy after the two-step ageing treatment were less with the first-step ageing at 115~C for different time periods （7, 14, and 21 h）. The effects of the second ageing parameters on the properties and microstructure of the 7B04 alloy were remarkable. TEM analysis of the samples aged at Temper I （7 h at 115℃ ＋ 12 h at 160℃） and Temper II （7 h at 115℃ ＋ 16 h at 165℃） indicates that two kinds of phases, i.e. 11＇ and 11 phases, precipitate from the matrix and efficiently improve the tensile strength of the alloy, and the grain boundary precipitates are coarse and discrete. There are obvious precipitate free zones （PFZs） along the grain boundary in the microstructure of the alloy after the two-step ageing treatment.展开更多
We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced wi...We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. This QSDC protocol has a higher capacity than the original two-step QSDC protocol as each photon pair can carry 4 bits of information. Compared with the QSDC protocol based on hyperdense coding, this QSDC protocol has the immunity to Trojan horse attack strategies with the process for determining the number of the photons in each quantum signal as it is a one-way quantum communication protocol.展开更多
Gametophytes of Laminaria japonica were cryopreserved in liquid nitrogen using encapsulation-dehydration with two-step cooling method. Gametophytes cultured at 10℃ and under continuous irradiance of 30 μmol m^-2 s^-...Gametophytes of Laminaria japonica were cryopreserved in liquid nitrogen using encapsulation-dehydration with two-step cooling method. Gametophytes cultured at 10℃ and under continuous irradiance of 30 μmol m^-2 s^-1 for 3 weeks were encapsulated in calcium alginate beads. The beads were dehydrated in 0.4 molLl sucrose prepared with seawater for 6 h, desiccated in an incubator set at 10℃ and 70% relative humidity for 4 h, pre-frozen at either -40℃ or -60℃ for 30 min, and stored in liquid nitrogen for 〉24 h. As high as 43% of survival rate was observed when gametophytes were thawed by placing the beads in 40℃ seawater and re-hydrated in 0.05 molL^-1 citrate sodium prepared using 30‰ NaCl 7 d later. More cells of male gametophytes survived the whole procedure in comparison with female gametophytes. The cells of gametophytes surviving the preservation were able to grow asexually and produce morphologically normal sporophytes.展开更多
Two-step steam reforming of methane (SRM) is a novel chemical looping process towards the production of pure hydrogen and syngas (synthesis gas), consisting of a syngas production step and a water-splitting step. Rene...Two-step steam reforming of methane (SRM) is a novel chemical looping process towards the production of pure hydrogen and syngas (synthesis gas), consisting of a syngas production step and a water-splitting step. Renewable energy can be used to drive this process for hydrogen production, especially solar energy. CeO2-Fe2O3 complex oxide oxygen carrier was prepared by the impregnation method and characterized by means of X-ray diffractometer (XRD), Raman spectroscopy (Raman) and hydrogen programmed reduction (H2-TPR). CH4 temperature programmed and isothermal reactions were adopted to test syngas production reactivity, and water splitting reaction was employed to investigate water-splitting activity. Moreover, two-step SRM performance was evaluated by a successive redox cycle. The results showed that CO-uncontaminated H2 and highly selective syngas (with H2/CO ratio close to 2) could be respectively obtained from two steps, and CeFeO3 formation was found in the first redox cycle and proved to be enhanced by the redox treatment. After 10 successive cycles, obvious CeFeO3 phase was detected, which may be responsible for favorable successive redox cycle performances.展开更多
The challenge of sintering ultrafine-grained refractory metals and alloys to full density is hereby addressed by pressureless two-step sintering in tungsten-rhenium alloy and pure molybdenum. Using properly processed ...The challenge of sintering ultrafine-grained refractory metals and alloys to full density is hereby addressed by pressureless two-step sintering in tungsten-rhenium alloy and pure molybdenum. Using properly processed nano powders(~50 nm average particle size), we are able to sinter W-10Re alloy to 98.4% density below 1200 ℃ while maintaining a fine grain size of 260 nm, and sinter molybdenum to 98.3% density below 1120 ℃ while maintaining a fine grain size of 290 nm. Compared to normal sintering,two-step sintering offers record-fine grain sizes and better microstructural uniformity, which translates to better mechanical properties with higher hardness(6.3 GPa for tungsten-rhenium and 4.0 GPa for molybdenum, both being the highest in all pressurelessly sintered samples of the respective material system)and larger Weibull modulus. Together with our previous demonstration in tungsten, we believe that twostep sintering is a general effective method to produce high-quality fine-grained refractory metals and alloys, and the lessons learned here are transferable to other materials for powder metallurgy.展开更多
The design of the two-step gear reducer is a tedious and time-consuming process. For the purpose of improving the efficiency and intelligence of design process, case-based reasoning（CBR） technology was applied to th...The design of the two-step gear reducer is a tedious and time-consuming process. For the purpose of improving the efficiency and intelligence of design process, case-based reasoning（CBR） technology was applied to the design of the two-step gear reducer. Firstly, the current design method for the two-step gear reducer was analyzed and the principle of CBR was described. Secondly, according to the characteristics of the reducer, three key technologies of CBR were studied and the corresponding methods were provided, which are as follows： （a） an object-oriented knowledge representation method, （b） a retrieval method combining the nearest neighbor with the induction indexing, and （c） a case adaptation algorithm combining the revision based on rule with artificial revision. Also, for the purpose of improving the credibility of case retrieval, a new method for determining the weights of characteristics and a similarity formula were presented, which is a combinatorial weighting method with the analytic hierarchy process（AHP） and roughness set theory. Lastly, according to the above analytic results, a design system of the two-step gear reducer on CBR was developed by VC＋＋, UG and Access 2003. A new method for the design of the two-step gear reducer is provided in this study. If the foregoing developed system is applied to design the two-step gear reducer, design efficiency is improved, which enables the designer to release from the tedious design process of the gear reducer so as to put more efforts on innovative design. The study result fully reflects the feasibility and validity of CBR technology in the process of the design of the mechanical parts.展开更多
A two-step leaching method in combination of acid and ethylene diaminetetraacetic acid disodium （EDTA-Na2） was applied to extract metals such as Cd, Cu, Fe, Pb and Zn from a zinc smelting slag. The results show that...A two-step leaching method in combination of acid and ethylene diaminetetraacetic acid disodium （EDTA-Na2） was applied to extract metals such as Cd, Cu, Fe, Pb and Zn from a zinc smelting slag. The results show that the extraction rates of Cd, Cu, Fe and Zn in slag reach 88.3%, 54.1%, 69.6% and 54.7%, respectively, while the extraction rate of Pb is only 0.05% leached with 1.25 mol/L sulfuric acid under the conditions of the ratio of slag to liquid of 100 g/L, 65 ℃ and 120 r/min for 2 h. However, Pb extraction rate from 1.25 mol/L sulfuric acid leached residue reaches as high as 66.5% by using 0.1 mol/L EDTA-Na2 solution. The results indicate that two-step sequential extraction procedure combining 1.25 mol/L sulfuric acid and 0.1 mol/L EDTA-Na2 solution can extensively extract Cd, Cu, Fe, Pb and Zn from zinc smelting slag.展开更多
CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane （SRM）. Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is di...CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane （SRM）. Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is directly converted to syngas at a H2/CO ratio close to 2 ： 1 at a high temperature （above 750 °C） by the lattice oxygen of CeO2; methane cracking is found when the reduction degree of CeO2 was above 5.0% at 850 °C in methane isothermal reaction. CeO2？δ obtained from methane isothermal reaction can split water to generate CO-free hydrogen and renew its lattice oxygen at 700 °C; simultaneously, deposited carbon is selectively oxidized to CO2 by steam following the reaction （C＋2H2O→CO2＋2H2）. Slight deactivation in terms of amounts of desired products （syngas and hydrogen） is observed in ten repetitive two-step SRM process due to the carbon deposition on CeO2 surface as well as sintering of CeO2.展开更多
基金supported by the National Natural Science Foun-dation of China(Nos.52025028,52332008,52372214,52202273,and U22A20137)the Priority Academic Program Development(PAPD)of Jiangsu Higher Education Institutions.
文摘Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method more easily controls the crystallization rate and is suitable for preparing large-area per-ovskite devices.However,the residual low-conductivity iodide layer in the two-step method can affect carrier transport and device stability,and the different crystallization rates of Sn-and Pb-based per-ovskites may result in poor film quality.Therefore,Sn-Pb mixed perovskites are mainly prepared by a one-step method.Herein,a MAPb_(0.5)Sn_(0.5)I_(3)-based self-powered photodetector without a hole transport layer is fabricated by a two-step method.By adjusting the concentration of the ascorbic acid(AA)addi-tive,the final perovskite film exhibited a pure phase without residues,and the optimal device exhibited a high responsivity(0.276 A W^(-1)),large specific detectivity(2.38×10^(12) Jones),and enhanced stability.This enhancement is mainly attributed to the inhibition of Sn2+oxidation,the control of crystal growth,and the sufficient reaction between organic ammonium salts and bottom halides due to the AA-induced pore structure.
文摘A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,confocal laser microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,transmission electron microscopy,and electrochemical analysis,are employed to characterize MAO coatings at different stages of preparation.MAO has MgO,hydroxyapatite,Ca_(3)(PO_(4))_(2),and Mg2SiO4 phases.Its microstructure of the coating is characterized by"multiple breakdowns,pores within pores",and"repaired blind pores".The porosity and the uniformity of MAO coating first declines in the constant voltage mode,then augments while the discharge phenomenon takes place,and finally decreases in the repair stage.These analyses reveal a four-stage growth pattern for MAO coatings:anodic oxidation stage,micro-arc oxidation stage,breakdown stage,and repairing stage.During anodic oxidation and MAO stages,inward growth prevails,while the breakdown stage sees outward and accelerated growth.Simultaneous inward and outward growth in the repair stage results in a denser,more uniform coating with increased thickness and improved corrosion resistance.
基金Natural Science Foundation of Shanghai(24ZR1400800)he Natural Science Foundation of China(U23A20685,52073058,91963204)+1 种基金the National Key R&D Program of China(2021YFB3701400)Shanghai Sailing Program(23YF1400200)。
文摘High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.
基金Project (2012CB722805) supported by the National Basic Research Program of ChinaProjects (50974083, 51174131) supported by the National Natural Science Foundation of China+1 种基金Project (50774112) supported by the Joint Fund of NSFC and Baosteel, ChinaProject(07QA4021) supported by the Shanghai "Phosphor" Science Foundation, China
文摘The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationship between the diffusion coefficient along the direction of z-axis which is normal to the Mg/Zn interface and temperature was investigated, and the AF＇s impact on the diffusion constant （D0） and activation energy （Q^＊） was studied. Then, two steps were taken to simulate the atomic diffusion process and the formation of new phases： one for acceleration and the other for equilibration. The results show that： the Arrhenius equation works well for the description of Dz with different accelerating factors; the AF has no effect on the diffusion constant Do in the case of no phase transition; and the relationship between Q＊ and Q conforms to Q^＊=Q/A. Then, the new Arrhenius equation for AFHD is successfully constructed as Dz=Doexp[-Q/（ART）]. Meanwhile, the authentic equilibrium conformations at any dynamic moment can only be reproduced by the equilibration simulation of the HD-simulated configurations. Key words： accelerating factor method; Arrhenius equation; two-steps scheme; Mg/Zn interface; hyperdynamic simulation
基金supported by the National Natural Science Foundation of China(No.52405408,No.U21A20131,No.U2037204,No.52422510)the Natural Science Foundation of Hubei Province(No.2023AFB116)+1 种基金the State Key Laboratory of Materials Processing and Die&Mould TechnologyHuazhong University of Science and Technology(No.P2022-005)。
文摘Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.
基金supported by the National Natural Science Foundation of China(No.92252201)the Fundamental Research Funds for the Central Universitiesthe Academic Excellence Foundation of Beihang University(BUAA)for PhD Students。
文摘Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of unsteady flows.To enhance computational efficiency,we propose the Implicit-Explicit Two-Step Runge-Kutta(IMEX-TSRK)time-stepping discretization methods for unsteady flows,and develop a novel adaptive algorithm that correctly partitions spatial regions to apply implicit or explicit methods.The novel adaptive IMEX-TSRK schemes effectively handle the numerical stiffness of the small grid size and improve computational efficiency.Compared to implicit and explicit Runge-Kutta(RK)schemes,the IMEX-TSRK methods achieve the same order of accuracy with fewer first derivative calculations.Numerical case tests demonstrate that the IMEX-TSRK methods maintain numerical stability while enhancing computational efficiency.Specifically,in high Reynolds number flows,the computational efficiency of the IMEX-TSRK methods surpasses that of explicit RK schemes by more than one order of magnitude,and that of implicit RK schemes several times over.
基金Project(51378510) supported by the National Natural Science Foundation of China。
文摘In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to characterize the strength of the backfill. However, the actual working temperature of slopes varies, and natural phenomena such as rainfall and groundwater infiltration commonly result in unsaturated soil conditions, with cracks typically present in cohesive slopes. This study introduces a novel approach for assessing the stability of unsaturated soil stepped slopes under varying temperatures, incorporating the effects of open and vertical cracks. Utilizing the kinematic approach and gravity increase method, we developed a three-dimensional (3D) rotational wedge failure mechanism to simulate slope collapse, enhancing the traditional two-dimensional analyses. We integrated temperature-dependent functions and nonlinear shear strength equations to evaluate the impact of temperature on four typical unsaturated soil types. A particle swarm optimization algorithm was employed to calculate the safety factor, ensuring our method’s accuracy by comparing it with existing studies. The results indicate that considering 3D effects yields a higher safety factor, while cracks reduce slope stability. Each unsaturated soil exhibits a distinctive temperature response curve, highlighting the importance of understanding soil types in the design phase.
文摘In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-step annealing protocol(H_(2)/Ar,600 and 800℃)to circumvent the sintering issues imposed by conventional thermodynamics.Physical characterizations(X-ray diffraction,high-angle annular dark-field scanning transmission electron microscopy,X-ray absorption spectroscopy)and theoretical calculations reveal that low-temperature annealing at 600℃stabilizes sub-nano disordered PtFe alloys via the strong metal-support interactions(SMSI)between Zn in ZnNC and Pt precursors,while high-temperature treatment at 800℃promotes Zn diffusion from the support into the alloy bulk and simultaneously triggers the disorder-to-order phase transition.The as-prepared ZnNC-15PtFeZn exhibits an initial mass activity of 0.769 mA/μgPt and retains 61.7%of its activity after 30000 cycles of accelerated stress testing(AST).Notably,when used as a cathode catalyst in MEA,ZnNC-15PtFeZn achieves superior power density(2.018 W/cm^(2)under H_(2)-O_(2))at half the Pt loading(0.05 mg/cm^(2))of state-of-the-art commercial Pt/C,highlighting its potential for low-Pt PEMFCs.Density functional theory confirms that Fe enhances ORR activity via ligand effects,while Zn strengthens Pt-Fe/Zn bonding(elevating vacancy formation energies),thereby improving structural stability.This mild,scalable aqueous impregnation strategy offers a general approach for synthesizing multi-component ordered alloys in electrocatalysis.
基金supported by the National Natural Science Foundation of China(Nos.52271148 and 51871129).
文摘Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based BMGs,restricting their commercial applications significantly.In this study,this challenge was addressed by introducing a two-step alloying strategy to mitigate the remarkable density increment effect associated with heavy alloying elements required for enhancing the GFA.Consequently,through two-step alloying with Al and Fe in sequence,simultaneous enhancements in specific strength and GFA were achieved based on a Ti-Zr-Be ternary metallic glass,resulting in the development of a series of centimeter-sized metallic glasses exhibiting ultrahigh-specific strength.Notably,the newly developed(Ti_(45)Zr_(20)Be_(31)A_(l4))_(94)Fe_(6)alloy established a new record for the specific strength of Ti-based BMGs.Along with a critical diameter(D_(c))of 10 mm,it offers the optimal scheme for balancing the specific strength and GFA of Ti-based BMGs.The present results further brighten the application prospects of Ti-based BMGs as lightweight materials.
基金Project supported by the National Key Research and Development Program of China (Grant No. 2021YFA1202900)the National Natural Science Foundation of China (Grant Nos. 12422402, 61888102, 12274447, and 62204166)+1 种基金Chinese Academy of Sciences Strategic Priority Research Program (Grant No. XDB067020302)Guangdong Major Project of Basic and Applied Basic Research (Grant No. 2021B0301030002)。
文摘Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer MoS_(2) has improved electron mobility and current density, and therefore provides a more promising platform in terms of thin-film transistors, flexible electronic devices, etc. However, the synthesis of large-area, high-quality multilayer MoS_(2) films with controlled layer number remains a challenge. Here, we develop a two-step oxygen-assisted chemical vapor deposition(OA-CVD) methodology for the synthesis of 4-inch MoS_(2) films from monolayer to trilayer on sapphire substrates. The influence of critical growth parameters on the growth of multilayer MoS_(2) is systematically explored, such as the evaporation temperature of MoO_(3) and the flow rate of O_(2). Flexible field-effect transistor(FET) devices fabricated from bilayer/trilayer MoS_(2) show substantial improvements in mobility compared with flexible FETs based on monolayer films.
基金Project(2010CB630901)supported by the National Basic Research Program of ChinaProject(2013M531814)supported by the 53rd China Postdoctoral Science Foundation
文摘In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during the bio-oxidation step was used. The results revealed that the optimum mode was to maintain solution p H at 1.0-1.2 during the biological oxidation stage. Under this condition, the activity of mixed culture could be sustained and the formation of jarosite could be diminished, thus the oxidation efficiency was improved. The oxidation levels of iron and sulfur were improved by 12.50% and 15.49%, and the gold recovery was increased by 21.02%. Therefore, the two-step process combined with p H control is an effective method for oxidizing the biohydrometallurgical process of Axi gold concentrate, and it will have a broad prospect of application in dealing with complex refractory gold concentrate.
基金Supported by the Natural Science Foundation of Tianjin(09JCZDJC19100)Scientific Research Fund of Tianjin Scienceand Technology University(20090403)~~
文摘[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first phase（0-10 h）was to improve cell growth,and the second phase（10-30 h）was to promote spore formation.Four factors including initial glucose concentration,fermentation pH,temperature（in the second phase）and shaking speed（in the second phase）were optimized using the methods of single factor test and orthogonal experiment.[Result] The initial glucose concentration showed a significant effect on sporulation.The optimal conditions for the spore formation of B.subtilis B579 were as follows：initial glucose concentration 5 g/L,fermentation pH 7.0,the temperature for the first phase 37 ℃,and the shaking speed for the first phase 180 r/min,the temperature for the second phase 40 ℃,and the shaking speed for the second phase 200 r/min;in addition,the first phase was 10 h and the second phase of fermentation was conducted for 30 h.Under such conditions,the spore concentration and spore formation rate could reach 9.43×108 CFU/ml and 90.99%,respectively,which represented 6.70-fold and 2.43-fold increase compared with those before optimization.[Conclusion] The spores concentration of biocontrol agent was improved using two-step control strategy,which provided the basis for biopesticide production in large scale.
基金the National High-Tech Research Development Program of China (No. 2003AA331100).
文摘The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that the initial T1 ageing contributes a major increase of the tensile strength, and the 0.2% proof stress value reaches 482 MPa after ageing for 7 h at 115℃. Behavioral differences in the tensile properties of the alloy after the two-step ageing treatment were less with the first-step ageing at 115~C for different time periods （7, 14, and 21 h）. The effects of the second ageing parameters on the properties and microstructure of the 7B04 alloy were remarkable. TEM analysis of the samples aged at Temper I （7 h at 115℃ ＋ 12 h at 160℃） and Temper II （7 h at 115℃ ＋ 16 h at 165℃） indicates that two kinds of phases, i.e. 11＇ and 11 phases, precipitate from the matrix and efficiently improve the tensile strength of the alloy, and the grain boundary precipitates are coarse and discrete. There are obvious precipitate free zones （PFZs） along the grain boundary in the microstructure of the alloy after the two-step ageing treatment.
基金supported by the Natural Science Foundation of Jiangsu Provincial Universities, China (Grant No. 10KJB180004)
文摘We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. This QSDC protocol has a higher capacity than the original two-step QSDC protocol as each photon pair can carry 4 bits of information. Compared with the QSDC protocol based on hyperdense coding, this QSDC protocol has the immunity to Trojan horse attack strategies with the process for determining the number of the photons in each quantum signal as it is a one-way quantum communication protocol.
文摘Gametophytes of Laminaria japonica were cryopreserved in liquid nitrogen using encapsulation-dehydration with two-step cooling method. Gametophytes cultured at 10℃ and under continuous irradiance of 30 μmol m^-2 s^-1 for 3 weeks were encapsulated in calcium alginate beads. The beads were dehydrated in 0.4 molLl sucrose prepared with seawater for 6 h, desiccated in an incubator set at 10℃ and 70% relative humidity for 4 h, pre-frozen at either -40℃ or -60℃ for 30 min, and stored in liquid nitrogen for 〉24 h. As high as 43% of survival rate was observed when gametophytes were thawed by placing the beads in 40℃ seawater and re-hydrated in 0.05 molL^-1 citrate sodium prepared using 30‰ NaCl 7 d later. More cells of male gametophytes survived the whole procedure in comparison with female gametophytes. The cells of gametophytes surviving the preservation were able to grow asexually and produce morphologically normal sporophytes.
基金Project support by the National Natural Science Foundation of China (50574046, 50774038)the Natural Science Foundation of Yunnan Prov-ince (2008E030M)+1 种基金the Research Fund for the Doctoral Program of Higher Education of China (20095314120005)2010 Innovation Fund of Kunming University of Science and Technology
文摘Two-step steam reforming of methane (SRM) is a novel chemical looping process towards the production of pure hydrogen and syngas (synthesis gas), consisting of a syngas production step and a water-splitting step. Renewable energy can be used to drive this process for hydrogen production, especially solar energy. CeO2-Fe2O3 complex oxide oxygen carrier was prepared by the impregnation method and characterized by means of X-ray diffractometer (XRD), Raman spectroscopy (Raman) and hydrogen programmed reduction (H2-TPR). CH4 temperature programmed and isothermal reactions were adopted to test syngas production reactivity, and water splitting reaction was employed to investigate water-splitting activity. Moreover, two-step SRM performance was evaluated by a successive redox cycle. The results showed that CO-uncontaminated H2 and highly selective syngas (with H2/CO ratio close to 2) could be respectively obtained from two steps, and CeFeO3 formation was found in the first redox cycle and proved to be enhanced by the redox treatment. After 10 successive cycles, obvious CeFeO3 phase was detected, which may be responsible for favorable successive redox cycle performances.
基金supports by the Natural Science Foundation of China(52074032,51974029,52131307,52071013)and“111”Project(No.B170003).Y.D.and J.L.acknowledge the support by Eni S.p.A.through the MIT Energy Initiative.
文摘The challenge of sintering ultrafine-grained refractory metals and alloys to full density is hereby addressed by pressureless two-step sintering in tungsten-rhenium alloy and pure molybdenum. Using properly processed nano powders(~50 nm average particle size), we are able to sinter W-10Re alloy to 98.4% density below 1200 ℃ while maintaining a fine grain size of 260 nm, and sinter molybdenum to 98.3% density below 1120 ℃ while maintaining a fine grain size of 290 nm. Compared to normal sintering,two-step sintering offers record-fine grain sizes and better microstructural uniformity, which translates to better mechanical properties with higher hardness(6.3 GPa for tungsten-rhenium and 4.0 GPa for molybdenum, both being the highest in all pressurelessly sintered samples of the respective material system)and larger Weibull modulus. Together with our previous demonstration in tungsten, we believe that twostep sintering is a general effective method to produce high-quality fine-grained refractory metals and alloys, and the lessons learned here are transferable to other materials for powder metallurgy.
基金This project is supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2008AA04Z115)Science and Technology Program of the Ministry of Construction of China (Grant No. 2008-K8-2)+1 种基金Jiangsu Provincial Natural Science Foundation of China (Grant No. BK2007042)Open Fund of State Key Lab of CAD&CG, Zhejiang University, China (Grant No. A0914)
文摘The design of the two-step gear reducer is a tedious and time-consuming process. For the purpose of improving the efficiency and intelligence of design process, case-based reasoning（CBR） technology was applied to the design of the two-step gear reducer. Firstly, the current design method for the two-step gear reducer was analyzed and the principle of CBR was described. Secondly, according to the characteristics of the reducer, three key technologies of CBR were studied and the corresponding methods were provided, which are as follows： （a） an object-oriented knowledge representation method, （b） a retrieval method combining the nearest neighbor with the induction indexing, and （c） a case adaptation algorithm combining the revision based on rule with artificial revision. Also, for the purpose of improving the credibility of case retrieval, a new method for determining the weights of characteristics and a similarity formula were presented, which is a combinatorial weighting method with the analytic hierarchy process（AHP） and roughness set theory. Lastly, according to the above analytic results, a design system of the two-step gear reducer on CBR was developed by VC＋＋, UG and Access 2003. A new method for the design of the two-step gear reducer is provided in this study. If the foregoing developed system is applied to design the two-step gear reducer, design efficiency is improved, which enables the designer to release from the tedious design process of the gear reducer so as to put more efforts on innovative design. The study result fully reflects the feasibility and validity of CBR technology in the process of the design of the mechanical parts.
基金Project(2011SK3262) supported by Science and Technology Program of Hunan Province,China
文摘A two-step leaching method in combination of acid and ethylene diaminetetraacetic acid disodium （EDTA-Na2） was applied to extract metals such as Cd, Cu, Fe, Pb and Zn from a zinc smelting slag. The results show that the extraction rates of Cd, Cu, Fe and Zn in slag reach 88.3%, 54.1%, 69.6% and 54.7%, respectively, while the extraction rate of Pb is only 0.05% leached with 1.25 mol/L sulfuric acid under the conditions of the ratio of slag to liquid of 100 g/L, 65 ℃ and 120 r/min for 2 h. However, Pb extraction rate from 1.25 mol/L sulfuric acid leached residue reaches as high as 66.5% by using 0.1 mol/L EDTA-Na2 solution. The results indicate that two-step sequential extraction procedure combining 1.25 mol/L sulfuric acid and 0.1 mol/L EDTA-Na2 solution can extensively extract Cd, Cu, Fe, Pb and Zn from zinc smelting slag.
基金supported by the National Natural Science Foundation of China (NO. 51004060)the Natural Science Foundation of Yunnan Province (NO. 2008E030M, 2010ZC108)+2 种基金the Research Foundation for the Doctoral Program of Higher Education of China (NO. 20095314120005)the Analysis and Test Foundation of Kunming University of Science and Technology (KUST)the 2010 Innovation Foundation of KUST
文摘CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane （SRM）. Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is directly converted to syngas at a H2/CO ratio close to 2 ： 1 at a high temperature （above 750 °C） by the lattice oxygen of CeO2; methane cracking is found when the reduction degree of CeO2 was above 5.0% at 850 °C in methane isothermal reaction. CeO2？δ obtained from methane isothermal reaction can split water to generate CO-free hydrogen and renew its lattice oxygen at 700 °C; simultaneously, deposited carbon is selectively oxidized to CO2 by steam following the reaction （C＋2H2O→CO2＋2H2）. Slight deactivation in terms of amounts of desired products （syngas and hydrogen） is observed in ten repetitive two-step SRM process due to the carbon deposition on CeO2 surface as well as sintering of CeO2.
