Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes ...Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes which are subjected to stress-induced failure.The probability of failure(POF)depends on many factors,of which the geometry of an open stope is especially important.In this study,a methodology is proposed to assess the effect of stope geometrical parameters on the POF,using numerical modelling.Different ranges for each input parameter are defined according to previous surveys on open stope geometry in a number of Canadian underground mines.A Monte-Carlo simulation technique is combined with the finite difference code FLAC3D,to generate model realizations containing stopes with different geometrical features.The probability of failure(POF)for different categories of stope geometry,is calculated by considering two modes of failure;relaxation-related gravity driven(tensile)failure and rock mass brittle failure.The individual and interactive effects of stope geometrical parameters on the POF,are analyzed using a general multi-level factorial design.Finally,mathematical optimization techniques are employed to estimate the most stable stope conditions,by determining the optimal ranges for each stope’s geometrical parameter.展开更多
Backfill is often employed in mining operations for ground support,with its positive impact on ground stability acknowledged in many underground mines.However,existing studies have predominantly focused only on the st...Backfill is often employed in mining operations for ground support,with its positive impact on ground stability acknowledged in many underground mines.However,existing studies have predominantly focused only on the stress development within the backfill material,leaving the influence of stope backfilling on stress distribution in surrounding rock mass and ground stability largely unexplored.Therefore,this paper presents numerical models in FLAC3D to investigate,for the first time,the time-dependent stress redistribution around a vertical backfilled stope and its implications on ground stability,considering the creep of surrounding rock mass.Using the Soft Soil constitutive model,the compressibility of backfill under large pressure was captured.It is found that the creep deformation of rock mass exercises compression on backfill and results in a less void ratio and increased modulus for fill material.The compacted backfill conversely influenced the stress distribution and ground stability of rock mass which was a combined effect of wall creep and compressibility of backfill.With the increase of time or/and creep deformation,the minimum principal stress in the rocks surrounding the backfilled stope increased towards the pre-mining stress state,while the deviatoric stress reduces leading to an increased factor of safety and improved ground stability.This improvement effect of backfill on ground stability increased with the increase of mine depth and stope height,while it is also more pronounced for the narrow stope,the backfill with a smaller compression index,and the soft rocks with a smaller viscosity coefficient.Furthermore,the results emphasize the importance of minimizing empty time and backfilling extracted stope as soon as possible for ground control.Reduction of filling gap height enhances the local stability around the roof of stope.展开更多
Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method mor...Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method more easily controls the crystallization rate and is suitable for preparing large-area per-ovskite devices.However,the residual low-conductivity iodide layer in the two-step method can affect carrier transport and device stability,and the different crystallization rates of Sn-and Pb-based per-ovskites may result in poor film quality.Therefore,Sn-Pb mixed perovskites are mainly prepared by a one-step method.Herein,a MAPb_(0.5)Sn_(0.5)I_(3)-based self-powered photodetector without a hole transport layer is fabricated by a two-step method.By adjusting the concentration of the ascorbic acid(AA)addi-tive,the final perovskite film exhibited a pure phase without residues,and the optimal device exhibited a high responsivity(0.276 A W^(-1)),large specific detectivity(2.38×10^(12) Jones),and enhanced stability.This enhancement is mainly attributed to the inhibition of Sn2+oxidation,the control of crystal growth,and the sufficient reaction between organic ammonium salts and bottom halides due to the AA-induced pore structure.展开更多
A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,conf...A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,confocal laser microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,transmission electron microscopy,and electrochemical analysis,are employed to characterize MAO coatings at different stages of preparation.MAO has MgO,hydroxyapatite,Ca_(3)(PO_(4))_(2),and Mg2SiO4 phases.Its microstructure of the coating is characterized by"multiple breakdowns,pores within pores",and"repaired blind pores".The porosity and the uniformity of MAO coating first declines in the constant voltage mode,then augments while the discharge phenomenon takes place,and finally decreases in the repair stage.These analyses reveal a four-stage growth pattern for MAO coatings:anodic oxidation stage,micro-arc oxidation stage,breakdown stage,and repairing stage.During anodic oxidation and MAO stages,inward growth prevails,while the breakdown stage sees outward and accelerated growth.Simultaneous inward and outward growth in the repair stage results in a denser,more uniform coating with increased thickness and improved corrosion resistance.展开更多
High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production meth...High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.展开更多
The shear characteristics of the interface formed between a cemented tailings backfill(CTB)and surrounding rocks play a cru-cial role in the design and stability of underground goafs.To investigate the shear behavior ...The shear characteristics of the interface formed between a cemented tailings backfill(CTB)and surrounding rocks play a cru-cial role in the design and stability of underground goafs.To investigate the shear behavior of CTB-rock interfaces,rock samples repres-enting the topography of surrounding rocks were constructed using 3D morphology scanning and engraving techniques.A series of direct shear tests were conducted on the CTB rock samples to examine the influence of the cement-tailings ratio on the interfacial shear behavi-or.The results showed that the compressive strength of the CTB and shear strength of the CTB-rock interface decreased with decreasing cement proportion.With deceasing cement content,the failure area of the CTB after the test increased,and the roughness of the newly generated interface reduced.A digital image correlation analysis revealed that the compressive stress concentration in the region with an obtuse angle with respect to the shear direction was the primary cause of CTB failure.Moreover,the correlation between the wear area and the silicon-dense area helped confirm that the silicon particles are more prone to failure in these areas than in other regions.Our find-ings provide new insights into the shear sliding mechanism at CTB-rock interfaces and can aid in the selection of the cement-tailings ra-tio at engineering sites.For example,if the horizontal principal stress of the surrounding rock mass in a backfilling area is relatively high,the cement content can be reduced for CTB applications.展开更多
Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from...Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.展开更多
Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of un...Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of unsteady flows.To enhance computational efficiency,we propose the Implicit-Explicit Two-Step Runge-Kutta(IMEX-TSRK)time-stepping discretization methods for unsteady flows,and develop a novel adaptive algorithm that correctly partitions spatial regions to apply implicit or explicit methods.The novel adaptive IMEX-TSRK schemes effectively handle the numerical stiffness of the small grid size and improve computational efficiency.Compared to implicit and explicit Runge-Kutta(RK)schemes,the IMEX-TSRK methods achieve the same order of accuracy with fewer first derivative calculations.Numerical case tests demonstrate that the IMEX-TSRK methods maintain numerical stability while enhancing computational efficiency.Specifically,in high Reynolds number flows,the computational efficiency of the IMEX-TSRK methods surpasses that of explicit RK schemes by more than one order of magnitude,and that of implicit RK schemes several times over.展开更多
In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to character...In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to characterize the strength of the backfill. However, the actual working temperature of slopes varies, and natural phenomena such as rainfall and groundwater infiltration commonly result in unsaturated soil conditions, with cracks typically present in cohesive slopes. This study introduces a novel approach for assessing the stability of unsaturated soil stepped slopes under varying temperatures, incorporating the effects of open and vertical cracks. Utilizing the kinematic approach and gravity increase method, we developed a three-dimensional (3D) rotational wedge failure mechanism to simulate slope collapse, enhancing the traditional two-dimensional analyses. We integrated temperature-dependent functions and nonlinear shear strength equations to evaluate the impact of temperature on four typical unsaturated soil types. A particle swarm optimization algorithm was employed to calculate the safety factor, ensuring our method’s accuracy by comparing it with existing studies. The results indicate that considering 3D effects yields a higher safety factor, while cracks reduce slope stability. Each unsaturated soil exhibits a distinctive temperature response curve, highlighting the importance of understanding soil types in the design phase.展开更多
Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based...Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based BMGs,restricting their commercial applications significantly.In this study,this challenge was addressed by introducing a two-step alloying strategy to mitigate the remarkable density increment effect associated with heavy alloying elements required for enhancing the GFA.Consequently,through two-step alloying with Al and Fe in sequence,simultaneous enhancements in specific strength and GFA were achieved based on a Ti-Zr-Be ternary metallic glass,resulting in the development of a series of centimeter-sized metallic glasses exhibiting ultrahigh-specific strength.Notably,the newly developed(Ti_(45)Zr_(20)Be_(31)A_(l4))_(94)Fe_(6)alloy established a new record for the specific strength of Ti-based BMGs.Along with a critical diameter(D_(c))of 10 mm,it offers the optimal scheme for balancing the specific strength and GFA of Ti-based BMGs.The present results further brighten the application prospects of Ti-based BMGs as lightweight materials.展开更多
In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-s...In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-step annealing protocol(H_(2)/Ar,600 and 800℃)to circumvent the sintering issues imposed by conventional thermodynamics.Physical characterizations(X-ray diffraction,high-angle annular dark-field scanning transmission electron microscopy,X-ray absorption spectroscopy)and theoretical calculations reveal that low-temperature annealing at 600℃stabilizes sub-nano disordered PtFe alloys via the strong metal-support interactions(SMSI)between Zn in ZnNC and Pt precursors,while high-temperature treatment at 800℃promotes Zn diffusion from the support into the alloy bulk and simultaneously triggers the disorder-to-order phase transition.The as-prepared ZnNC-15PtFeZn exhibits an initial mass activity of 0.769 mA/μgPt and retains 61.7%of its activity after 30000 cycles of accelerated stress testing(AST).Notably,when used as a cathode catalyst in MEA,ZnNC-15PtFeZn achieves superior power density(2.018 W/cm^(2)under H_(2)-O_(2))at half the Pt loading(0.05 mg/cm^(2))of state-of-the-art commercial Pt/C,highlighting its potential for low-Pt PEMFCs.Density functional theory confirms that Fe enhances ORR activity via ligand effects,while Zn strengthens Pt-Fe/Zn bonding(elevating vacancy formation energies),thereby improving structural stability.This mild,scalable aqueous impregnation strategy offers a general approach for synthesizing multi-component ordered alloys in electrocatalysis.展开更多
Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer ...Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer MoS_(2) has improved electron mobility and current density, and therefore provides a more promising platform in terms of thin-film transistors, flexible electronic devices, etc. However, the synthesis of large-area, high-quality multilayer MoS_(2) films with controlled layer number remains a challenge. Here, we develop a two-step oxygen-assisted chemical vapor deposition(OA-CVD) methodology for the synthesis of 4-inch MoS_(2) films from monolayer to trilayer on sapphire substrates. The influence of critical growth parameters on the growth of multilayer MoS_(2) is systematically explored, such as the evaporation temperature of MoO_(3) and the flow rate of O_(2). Flexible field-effect transistor(FET) devices fabricated from bilayer/trilayer MoS_(2) show substantial improvements in mobility compared with flexible FETs based on monolayer films.展开更多
In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during ...In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during the bio-oxidation step was used. The results revealed that the optimum mode was to maintain solution p H at 1.0-1.2 during the biological oxidation stage. Under this condition, the activity of mixed culture could be sustained and the formation of jarosite could be diminished, thus the oxidation efficiency was improved. The oxidation levels of iron and sulfur were improved by 12.50% and 15.49%, and the gold recovery was increased by 21.02%. Therefore, the two-step process combined with p H control is an effective method for oxidizing the biohydrometallurgical process of Axi gold concentrate, and it will have a broad prospect of application in dealing with complex refractory gold concentrate.展开更多
[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first ...[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first phase（0-10 h）was to improve cell growth,and the second phase（10-30 h）was to promote spore formation.Four factors including initial glucose concentration,fermentation pH,temperature（in the second phase）and shaking speed（in the second phase）were optimized using the methods of single factor test and orthogonal experiment.[Result] The initial glucose concentration showed a significant effect on sporulation.The optimal conditions for the spore formation of B.subtilis B579 were as follows：initial glucose concentration 5 g/L,fermentation pH 7.0,the temperature for the first phase 37 ℃,and the shaking speed for the first phase 180 r/min,the temperature for the second phase 40 ℃,and the shaking speed for the second phase 200 r/min;in addition,the first phase was 10 h and the second phase of fermentation was conducted for 30 h.Under such conditions,the spore concentration and spore formation rate could reach 9.43×108 CFU/ml and 90.99%,respectively,which represented 6.70-fold and 2.43-fold increase compared with those before optimization.[Conclusion] The spores concentration of biocontrol agent was improved using two-step control strategy,which provided the basis for biopesticide production in large scale.展开更多
The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationsh...The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationship between the diffusion coefficient along the direction of z-axis which is normal to the Mg/Zn interface and temperature was investigated, and the AF＇s impact on the diffusion constant （D0） and activation energy （Q^＊） was studied. Then, two steps were taken to simulate the atomic diffusion process and the formation of new phases： one for acceleration and the other for equilibration. The results show that： the Arrhenius equation works well for the description of Dz with different accelerating factors; the AF has no effect on the diffusion constant Do in the case of no phase transition; and the relationship between Q＊ and Q conforms to Q^＊=Q/A. Then, the new Arrhenius equation for AFHD is successfully constructed as Dz=Doexp[-Q/（ART）]. Meanwhile, the authentic equilibrium conformations at any dynamic moment can only be reproduced by the equilibration simulation of the HD-simulated configurations. Key words： accelerating factor method; Arrhenius equation; two-steps scheme; Mg/Zn interface; hyperdynamic simulation展开更多
Backflling represents an environmentally friendly mining waste disposal technique.It is increasingly used in underground mines all over the world.However,its primary purpose remains to improve ground stability and to ...Backflling represents an environmentally friendly mining waste disposal technique.It is increasingly used in underground mines all over the world.However,its primary purpose remains to improve ground stability and to reduce ore dilution.Previous investigations have shown that fll drainage plays a key role in backfll and barricade design.With a poor drainage system in the backflled stope,the required dimension of barricade,which is constructed at the base of the stope near the drift entrance,has to be increased.A poor backfll drainage system can also lead to a signifcant increase in drainage waiting time and further reduction in mining productivity.In this paper,the drainage of conventional backfll design in backflled stopes is briefly reviewed.For the frst time,the application of the wick drain is introduced in the backfll within mine stopes.The drainage improvement from the introduction of the wick drain is illustrated using numerical modeling.展开更多
The nonlinear dynamical behaviors of artificial neural network (ANN) and their application to science and engineering were summarized. The mechanism of two kinds of dynamical processes, i.e. weight dynamics and activa...The nonlinear dynamical behaviors of artificial neural network (ANN) and their application to science and engineering were summarized. The mechanism of two kinds of dynamical processes, i.e. weight dynamics and activation dynamics in neural networks, and the stability of computing in structural analysis and design were stated briefly. It was successfully applied to nonlinear neural network to evaluate the stability of underground stope structure in a gold mine. With the application of BP network, it is proven that the neuro-com- puting is a practical and advanced tool for solving large-scale underground rock engineering problems.展开更多
We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced wi...We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. This QSDC protocol has a higher capacity than the original two-step QSDC protocol as each photon pair can carry 4 bits of information. Compared with the QSDC protocol based on hyperdense coding, this QSDC protocol has the immunity to Trojan horse attack strategies with the process for determining the number of the photons in each quantum signal as it is a one-way quantum communication protocol.展开更多
Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,wh...Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,which needs much reinforcement and support prior to mining.Cement-sodium silicate grout technology was selected,then its related parameters such as grout pressure,diffusion radius and time were calculated and proposed.In order to test the effect of the pressured grout in the fractured No.4 ore block,field experiments were conducted.To optimize stoping configuration,three-dimensional numerical simulation with ANSYS and FLAC 3 D softwares was proposed.The results show that the drilling porosity and mechanical properties of the rock masses are increased obviously.After grout,ore recovery rate is increased by 10.2%employing the newly designed stoping configuration compared with the previous.Last,analyzed from the surface movements,roof subsidence and the maximum principal stress of the pillars,the mining safety is probable of being ensured.展开更多
For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test sta...For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.展开更多
基金funded by a grant from Natural Sciences and Engineering Research Council of Canada (NSERC)the authors would like to acknowledge the Niobec mine (Saint-Honoré, QuébecQuébec)
文摘Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes which are subjected to stress-induced failure.The probability of failure(POF)depends on many factors,of which the geometry of an open stope is especially important.In this study,a methodology is proposed to assess the effect of stope geometrical parameters on the POF,using numerical modelling.Different ranges for each input parameter are defined according to previous surveys on open stope geometry in a number of Canadian underground mines.A Monte-Carlo simulation technique is combined with the finite difference code FLAC3D,to generate model realizations containing stopes with different geometrical features.The probability of failure(POF)for different categories of stope geometry,is calculated by considering two modes of failure;relaxation-related gravity driven(tensile)failure and rock mass brittle failure.The individual and interactive effects of stope geometrical parameters on the POF,are analyzed using a general multi-level factorial design.Finally,mathematical optimization techniques are employed to estimate the most stable stope conditions,by determining the optimal ranges for each stope’s geometrical parameter.
基金the funding support from the National Natural Science Foundation of China(Grant Nos.52304101 and 52004206)the China Postdoctoral Science Foundation(Grant No.2023MD734215)。
文摘Backfill is often employed in mining operations for ground support,with its positive impact on ground stability acknowledged in many underground mines.However,existing studies have predominantly focused only on the stress development within the backfill material,leaving the influence of stope backfilling on stress distribution in surrounding rock mass and ground stability largely unexplored.Therefore,this paper presents numerical models in FLAC3D to investigate,for the first time,the time-dependent stress redistribution around a vertical backfilled stope and its implications on ground stability,considering the creep of surrounding rock mass.Using the Soft Soil constitutive model,the compressibility of backfill under large pressure was captured.It is found that the creep deformation of rock mass exercises compression on backfill and results in a less void ratio and increased modulus for fill material.The compacted backfill conversely influenced the stress distribution and ground stability of rock mass which was a combined effect of wall creep and compressibility of backfill.With the increase of time or/and creep deformation,the minimum principal stress in the rocks surrounding the backfilled stope increased towards the pre-mining stress state,while the deviatoric stress reduces leading to an increased factor of safety and improved ground stability.This improvement effect of backfill on ground stability increased with the increase of mine depth and stope height,while it is also more pronounced for the narrow stope,the backfill with a smaller compression index,and the soft rocks with a smaller viscosity coefficient.Furthermore,the results emphasize the importance of minimizing empty time and backfilling extracted stope as soon as possible for ground control.Reduction of filling gap height enhances the local stability around the roof of stope.
基金supported by the National Natural Science Foun-dation of China(Nos.52025028,52332008,52372214,52202273,and U22A20137)the Priority Academic Program Development(PAPD)of Jiangsu Higher Education Institutions.
文摘Tin(Sn)-lead(Pb)mixed halide perovskites have attracted widespread interest due to their wider re-sponse wavelength and lower toxicity than lead halide perovskites,Among the preparation methods,the two-step method more easily controls the crystallization rate and is suitable for preparing large-area per-ovskite devices.However,the residual low-conductivity iodide layer in the two-step method can affect carrier transport and device stability,and the different crystallization rates of Sn-and Pb-based per-ovskites may result in poor film quality.Therefore,Sn-Pb mixed perovskites are mainly prepared by a one-step method.Herein,a MAPb_(0.5)Sn_(0.5)I_(3)-based self-powered photodetector without a hole transport layer is fabricated by a two-step method.By adjusting the concentration of the ascorbic acid(AA)addi-tive,the final perovskite film exhibited a pure phase without residues,and the optimal device exhibited a high responsivity(0.276 A W^(-1)),large specific detectivity(2.38×10^(12) Jones),and enhanced stability.This enhancement is mainly attributed to the inhibition of Sn2+oxidation,the control of crystal growth,and the sufficient reaction between organic ammonium salts and bottom halides due to the AA-induced pore structure.
文摘A custom micro-arc oxidation(MAO)apparatus is employed to produce coatings under optimized constant voltage–current two-step power supply mode.Various analytical techniques,including scanning electron microscopy,confocal laser microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,transmission electron microscopy,and electrochemical analysis,are employed to characterize MAO coatings at different stages of preparation.MAO has MgO,hydroxyapatite,Ca_(3)(PO_(4))_(2),and Mg2SiO4 phases.Its microstructure of the coating is characterized by"multiple breakdowns,pores within pores",and"repaired blind pores".The porosity and the uniformity of MAO coating first declines in the constant voltage mode,then augments while the discharge phenomenon takes place,and finally decreases in the repair stage.These analyses reveal a four-stage growth pattern for MAO coatings:anodic oxidation stage,micro-arc oxidation stage,breakdown stage,and repairing stage.During anodic oxidation and MAO stages,inward growth prevails,while the breakdown stage sees outward and accelerated growth.Simultaneous inward and outward growth in the repair stage results in a denser,more uniform coating with increased thickness and improved corrosion resistance.
基金Natural Science Foundation of Shanghai(24ZR1400800)he Natural Science Foundation of China(U23A20685,52073058,91963204)+1 种基金the National Key R&D Program of China(2021YFB3701400)Shanghai Sailing Program(23YF1400200)。
文摘High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.
基金supported by the National Natural Science Foundation of China(No.52374153).
文摘The shear characteristics of the interface formed between a cemented tailings backfill(CTB)and surrounding rocks play a cru-cial role in the design and stability of underground goafs.To investigate the shear behavior of CTB-rock interfaces,rock samples repres-enting the topography of surrounding rocks were constructed using 3D morphology scanning and engraving techniques.A series of direct shear tests were conducted on the CTB rock samples to examine the influence of the cement-tailings ratio on the interfacial shear behavi-or.The results showed that the compressive strength of the CTB and shear strength of the CTB-rock interface decreased with decreasing cement proportion.With deceasing cement content,the failure area of the CTB after the test increased,and the roughness of the newly generated interface reduced.A digital image correlation analysis revealed that the compressive stress concentration in the region with an obtuse angle with respect to the shear direction was the primary cause of CTB failure.Moreover,the correlation between the wear area and the silicon-dense area helped confirm that the silicon particles are more prone to failure in these areas than in other regions.Our find-ings provide new insights into the shear sliding mechanism at CTB-rock interfaces and can aid in the selection of the cement-tailings ra-tio at engineering sites.For example,if the horizontal principal stress of the surrounding rock mass in a backfilling area is relatively high,the cement content can be reduced for CTB applications.
基金supported by the National Natural Science Foundation of China(No.52405408,No.U21A20131,No.U2037204,No.52422510)the Natural Science Foundation of Hubei Province(No.2023AFB116)+1 种基金the State Key Laboratory of Materials Processing and Die&Mould TechnologyHuazhong University of Science and Technology(No.P2022-005)。
文摘Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.
基金supported by the National Natural Science Foundation of China(No.92252201)the Fundamental Research Funds for the Central Universitiesthe Academic Excellence Foundation of Beihang University(BUAA)for PhD Students。
文摘Efficient and accurate simulation of unsteady flow presents a significant challenge that needs to be overcome in computational fluid dynamics.Temporal discretization method plays a crucial role in the simulation of unsteady flows.To enhance computational efficiency,we propose the Implicit-Explicit Two-Step Runge-Kutta(IMEX-TSRK)time-stepping discretization methods for unsteady flows,and develop a novel adaptive algorithm that correctly partitions spatial regions to apply implicit or explicit methods.The novel adaptive IMEX-TSRK schemes effectively handle the numerical stiffness of the small grid size and improve computational efficiency.Compared to implicit and explicit Runge-Kutta(RK)schemes,the IMEX-TSRK methods achieve the same order of accuracy with fewer first derivative calculations.Numerical case tests demonstrate that the IMEX-TSRK methods maintain numerical stability while enhancing computational efficiency.Specifically,in high Reynolds number flows,the computational efficiency of the IMEX-TSRK methods surpasses that of explicit RK schemes by more than one order of magnitude,and that of implicit RK schemes several times over.
基金Project(51378510) supported by the National Natural Science Foundation of China。
文摘In existing studies, most slope stability analyses concentrate on conditions with constant temperature, assuming the slope is intact, and employ the Mohr-Coulomb (M-C) failure criterion for saturated soil to characterize the strength of the backfill. However, the actual working temperature of slopes varies, and natural phenomena such as rainfall and groundwater infiltration commonly result in unsaturated soil conditions, with cracks typically present in cohesive slopes. This study introduces a novel approach for assessing the stability of unsaturated soil stepped slopes under varying temperatures, incorporating the effects of open and vertical cracks. Utilizing the kinematic approach and gravity increase method, we developed a three-dimensional (3D) rotational wedge failure mechanism to simulate slope collapse, enhancing the traditional two-dimensional analyses. We integrated temperature-dependent functions and nonlinear shear strength equations to evaluate the impact of temperature on four typical unsaturated soil types. A particle swarm optimization algorithm was employed to calculate the safety factor, ensuring our method’s accuracy by comparing it with existing studies. The results indicate that considering 3D effects yields a higher safety factor, while cracks reduce slope stability. Each unsaturated soil exhibits a distinctive temperature response curve, highlighting the importance of understanding soil types in the design phase.
基金supported by the National Natural Science Foundation of China(Nos.52271148 and 51871129).
文摘Ti-based bulk metallic glasses(BMGs)have attracted increasing attention due to their high specific strength.However,a fundamental conflict exists between the specific strength and glass-forming ability(GFA)of Ti-based BMGs,restricting their commercial applications significantly.In this study,this challenge was addressed by introducing a two-step alloying strategy to mitigate the remarkable density increment effect associated with heavy alloying elements required for enhancing the GFA.Consequently,through two-step alloying with Al and Fe in sequence,simultaneous enhancements in specific strength and GFA were achieved based on a Ti-Zr-Be ternary metallic glass,resulting in the development of a series of centimeter-sized metallic glasses exhibiting ultrahigh-specific strength.Notably,the newly developed(Ti_(45)Zr_(20)Be_(31)A_(l4))_(94)Fe_(6)alloy established a new record for the specific strength of Ti-based BMGs.Along with a critical diameter(D_(c))of 10 mm,it offers the optimal scheme for balancing the specific strength and GFA of Ti-based BMGs.The present results further brighten the application prospects of Ti-based BMGs as lightweight materials.
文摘In this paper,we report the design of ultrafine ordered PtFeZn ternary intermetallics uniformly supported on ZIF-8-derived Zn,N-codoped graphitic carbon(ZnNC)via a green aqueous impregnation method followed by a two-step annealing protocol(H_(2)/Ar,600 and 800℃)to circumvent the sintering issues imposed by conventional thermodynamics.Physical characterizations(X-ray diffraction,high-angle annular dark-field scanning transmission electron microscopy,X-ray absorption spectroscopy)and theoretical calculations reveal that low-temperature annealing at 600℃stabilizes sub-nano disordered PtFe alloys via the strong metal-support interactions(SMSI)between Zn in ZnNC and Pt precursors,while high-temperature treatment at 800℃promotes Zn diffusion from the support into the alloy bulk and simultaneously triggers the disorder-to-order phase transition.The as-prepared ZnNC-15PtFeZn exhibits an initial mass activity of 0.769 mA/μgPt and retains 61.7%of its activity after 30000 cycles of accelerated stress testing(AST).Notably,when used as a cathode catalyst in MEA,ZnNC-15PtFeZn achieves superior power density(2.018 W/cm^(2)under H_(2)-O_(2))at half the Pt loading(0.05 mg/cm^(2))of state-of-the-art commercial Pt/C,highlighting its potential for low-Pt PEMFCs.Density functional theory confirms that Fe enhances ORR activity via ligand effects,while Zn strengthens Pt-Fe/Zn bonding(elevating vacancy formation energies),thereby improving structural stability.This mild,scalable aqueous impregnation strategy offers a general approach for synthesizing multi-component ordered alloys in electrocatalysis.
基金Project supported by the National Key Research and Development Program of China (Grant No. 2021YFA1202900)the National Natural Science Foundation of China (Grant Nos. 12422402, 61888102, 12274447, and 62204166)+1 种基金Chinese Academy of Sciences Strategic Priority Research Program (Grant No. XDB067020302)Guangdong Major Project of Basic and Applied Basic Research (Grant No. 2021B0301030002)。
文摘Molybdenum disulfide(MoS_(2)) is an emerging two-dimensional(2D) semiconductor and has great potential for highend applications beyond the traditional silicon-based electronics. Compared to the monolayers, multilayer MoS_(2) has improved electron mobility and current density, and therefore provides a more promising platform in terms of thin-film transistors, flexible electronic devices, etc. However, the synthesis of large-area, high-quality multilayer MoS_(2) films with controlled layer number remains a challenge. Here, we develop a two-step oxygen-assisted chemical vapor deposition(OA-CVD) methodology for the synthesis of 4-inch MoS_(2) films from monolayer to trilayer on sapphire substrates. The influence of critical growth parameters on the growth of multilayer MoS_(2) is systematically explored, such as the evaporation temperature of MoO_(3) and the flow rate of O_(2). Flexible field-effect transistor(FET) devices fabricated from bilayer/trilayer MoS_(2) show substantial improvements in mobility compared with flexible FETs based on monolayer films.
基金Project(2010CB630901)supported by the National Basic Research Program of ChinaProject(2013M531814)supported by the 53rd China Postdoctoral Science Foundation
文摘In order to improve the bio-oxidation efficiency of Axi refractory gold concentrate, a two-step process including a high temperature chemical oxidation and a subsequent bio-oxidation, combined with p H control during the bio-oxidation step was used. The results revealed that the optimum mode was to maintain solution p H at 1.0-1.2 during the biological oxidation stage. Under this condition, the activity of mixed culture could be sustained and the formation of jarosite could be diminished, thus the oxidation efficiency was improved. The oxidation levels of iron and sulfur were improved by 12.50% and 15.49%, and the gold recovery was increased by 21.02%. Therefore, the two-step process combined with p H control is an effective method for oxidizing the biohydrometallurgical process of Axi gold concentrate, and it will have a broad prospect of application in dealing with complex refractory gold concentrate.
基金Supported by the Natural Science Foundation of Tianjin(09JCZDJC19100)Scientific Research Fund of Tianjin Scienceand Technology University(20090403)~~
文摘[Objective] For preparing the biopesticide of Bacillus subtilis B579 with high spore concentration,the sporulation conditions were optimized.[Method] Two-step fermentation control strategy was used,in which,the first phase（0-10 h）was to improve cell growth,and the second phase（10-30 h）was to promote spore formation.Four factors including initial glucose concentration,fermentation pH,temperature（in the second phase）and shaking speed（in the second phase）were optimized using the methods of single factor test and orthogonal experiment.[Result] The initial glucose concentration showed a significant effect on sporulation.The optimal conditions for the spore formation of B.subtilis B579 were as follows：initial glucose concentration 5 g/L,fermentation pH 7.0,the temperature for the first phase 37 ℃,and the shaking speed for the first phase 180 r/min,the temperature for the second phase 40 ℃,and the shaking speed for the second phase 200 r/min;in addition,the first phase was 10 h and the second phase of fermentation was conducted for 30 h.Under such conditions,the spore concentration and spore formation rate could reach 9.43×108 CFU/ml and 90.99%,respectively,which represented 6.70-fold and 2.43-fold increase compared with those before optimization.[Conclusion] The spores concentration of biocontrol agent was improved using two-step control strategy,which provided the basis for biopesticide production in large scale.
基金Project (2012CB722805) supported by the National Basic Research Program of ChinaProjects (50974083, 51174131) supported by the National Natural Science Foundation of China+1 种基金Project (50774112) supported by the Joint Fund of NSFC and Baosteel, ChinaProject(07QA4021) supported by the Shanghai "Phosphor" Science Foundation, China
文摘The accelerating factor （AF） method is a simple and appropriate way to investigate the atomic long-time deep diffusion at solid-solid interface. In the framework of AF hyperdynamics （HD） simulation, the relationship between the diffusion coefficient along the direction of z-axis which is normal to the Mg/Zn interface and temperature was investigated, and the AF＇s impact on the diffusion constant （D0） and activation energy （Q^＊） was studied. Then, two steps were taken to simulate the atomic diffusion process and the formation of new phases： one for acceleration and the other for equilibration. The results show that： the Arrhenius equation works well for the description of Dz with different accelerating factors; the AF has no effect on the diffusion constant Do in the case of no phase transition; and the relationship between Q＊ and Q conforms to Q^＊=Q/A. Then, the new Arrhenius equation for AFHD is successfully constructed as Dz=Doexp[-Q/（ART）]. Meanwhile, the authentic equilibrium conformations at any dynamic moment can only be reproduced by the equilibration simulation of the HD-simulated configurations. Key words： accelerating factor method; Arrhenius equation; two-steps scheme; Mg/Zn interface; hyperdynamic simulation
基金the financial support of School of Advanced Technology(FIRPSIRE-research+1 种基金FDETS)the Natural Sciences and Engineering Research Council of Canada(RGPIN)
文摘Backflling represents an environmentally friendly mining waste disposal technique.It is increasingly used in underground mines all over the world.However,its primary purpose remains to improve ground stability and to reduce ore dilution.Previous investigations have shown that fll drainage plays a key role in backfll and barricade design.With a poor drainage system in the backflled stope,the required dimension of barricade,which is constructed at the base of the stope near the drift entrance,has to be increased.A poor backfll drainage system can also lead to a signifcant increase in drainage waiting time and further reduction in mining productivity.In this paper,the drainage of conventional backfll design in backflled stopes is briefly reviewed.For the frst time,the application of the wick drain is introduced in the backfll within mine stopes.The drainage improvement from the introduction of the wick drain is illustrated using numerical modeling.
基金This work was financially supported by the Key Project for National Science of "9.5" (Reward Ⅱ for National Science and Technol
文摘The nonlinear dynamical behaviors of artificial neural network (ANN) and their application to science and engineering were summarized. The mechanism of two kinds of dynamical processes, i.e. weight dynamics and activation dynamics in neural networks, and the stability of computing in structural analysis and design were stated briefly. It was successfully applied to nonlinear neural network to evaluate the stability of underground stope structure in a gold mine. With the application of BP network, it is proven that the neuro-com- puting is a practical and advanced tool for solving large-scale underground rock engineering problems.
基金supported by the Natural Science Foundation of Jiangsu Provincial Universities, China (Grant No. 10KJB180004)
文摘We propose a two-step quantum secure direct communication （QSDC） protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. This QSDC protocol has a higher capacity than the original two-step QSDC protocol as each photon pair can carry 4 bits of information. Compared with the QSDC protocol based on hyperdense coding, this QSDC protocol has the immunity to Trojan horse attack strategies with the process for determining the number of the photons in each quantum signal as it is a one-way quantum communication protocol.
基金Projects(51374034,51674012)supported by the National Natural Science Foundation of ChinaProject(2013BAB02B05)supported by the China National Science and Technology Support Program during the 12th Five-Year Plan Period
文摘Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,which needs much reinforcement and support prior to mining.Cement-sodium silicate grout technology was selected,then its related parameters such as grout pressure,diffusion radius and time were calculated and proposed.In order to test the effect of the pressured grout in the fractured No.4 ore block,field experiments were conducted.To optimize stoping configuration,three-dimensional numerical simulation with ANSYS and FLAC 3 D softwares was proposed.The results show that the drilling porosity and mechanical properties of the rock masses are increased obviously.After grout,ore recovery rate is increased by 10.2%employing the newly designed stoping configuration compared with the previous.Last,analyzed from the surface movements,roof subsidence and the maximum principal stress of the pillars,the mining safety is probable of being ensured.
基金the Major Programs of the National Basic Research Program of China (No.2005CB221503)the National Natural Science Foundation of China (Nos. 70533050 and 50674089) for their support of this project
文摘For a study of the movement and deformation of coal-rock mass and low protected seams below a stope,as well as for fracture developments and rules of evolution of permeability,we designed a plane strain model test stand to carry out model tests of similar materials in order to improve the effect of gas drainage from low protected seams and to measure the movement and deformation of coal-rock mass using a method of non-contact close-range photogrammetry.Our results show that 1) using paraffin melting to take the place of coal seam mining can satisfy the mining conditions of a protective seam;2) coal-rock mass under goafs has an upward movement after the protective seam has been mined,causing floor heaving;3) low protected seams become swollen and deformed,providing a good pressure-relief effect and causing the coal-rock mass under both sides of coal pillars to become deformed by compression and 4) the evolution of permeability of low protected seams follows the way of initial values→a slight decrease→a great increase→stability→final decrease.Simultaneously,the coefficient of air permeability increased at a decreasing rate with an increase in interlayer spacing.
